PROVN OF WASHING POINT FOR PATIENTS CLOTHES NEAR BLDG NO T-201, 01 X TOILET NEAR BLDG NO P-274 OF CAMP DET, 01 X STORAGE ROOM FOR OR MESS AND CERTAIN MINOR WORK AT MASIMPUR MILITARY STATION UNDER GE SILCHAR

Amount

PART-I (B/R WORKS) Surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc. 1.50 m deep and 1.50 m wide and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas, n exc 1.5m deep and getting out in any type of soil complete all as specified and directed.

As per item No. 3 but exc 1.5 mtr deep & not exc 3 mtr deep complete all as specified and directed.

Earth filling under floor incl spreading, levelling & well ramming includuing watering as required n exc . 25 cm thick complete all as specified and directed. Note :- Earth obtained from item No. 2 to 4 is reused

Surface excavation n.exc 30 cm deep and averaging 15cm deep ad getting out in soft/loose soil complete all as specified and directed.

Returning filling in incl watering, ramming in layers n.exc. 25cm thick in soil complete all as specified and directed.

Removing excavated surplus soil to a distance n.exc. 50m and depositing where directed at level n.exc. 1.50m above the starting point complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 Cum getting out soft/ disintegrated soil returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and makind good surface complete all as specified and directed.

M&L for Hardcore of broken stone of gauge n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for loose filling with broken bricks of guage 40 to 80 mm in soakage wells complete all as specified and directed.

M&L sand filling under floors or in foundation including watering levelling and consoliation complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Material and Labour for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregates as in foundations, mass concrete etc complete all as specified.

M&L for Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and directed.

M&L for Use and waste of Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for Use and waste of form work to chullah hoods, chajjas, shelves troughs and similar items including edges, for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for Use and waste of Form work to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantilevers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to edges of roof slab exc 10cm wide but n. exc 20cm wide as rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar works n.exc, 200mm thick (Horizontal or sloping) for flat surfaces as rough finished surfaces of concrete complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design mix ) using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design mix ) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design mix ) using 20 mm graded aggregate as in Chajja etc complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design mix ) using 20 mm graded aggregate in slabs supported on walls, beams etc complete all as specified and directed.

Material and labour for 10mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No. 26 here in before but 6mm to 8mm dia

All as per item No. 26 here in before but mild steel bar 5 mm and over up to 10 mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B0 damp proof course to horizontal or vertical surfaces incl necessary formwork and applying a coat of blown type bitumen at the rate of 1.50kg per square metre and blinding with clean dry sand @ 0.05cum per sqm complete all as specified and directed.

M&L Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L for half brick work with sub class 'B' bricks straight or curved on plan to radius built in cement mortar 1:4 complete all as specified and directed.

M&L for Cutting openings, through brick walls built in Cement mortor for door, window and other openings or enlarging existing openings , converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and directed.

M&L for forming jambs etc to opening (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete all as specified and directed.

Material and labour for brickwork, with subclass ‘B’ bricks in one brick thick honey comb work, built in cement mortar (1:4) all as specified and directed.

Material and Labour for 70mm thick PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in floor finished even & fair complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in flooring finished even & fair complete all as specified and directed.

S&F glass diving strip 3mm thick and 38mm width complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement laid shall be alternate panels and joints filled with bituminous 1 part and 3 part of sand complete all as specified and directed.

M&L plain cement concrete type C1 (1:3:6) using 20 mm graded aggregate in surface channel/drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm thick jointed in grey cement slurry mixed with pigment to match the shade of the slab as in flooring incl rubbing and mirror finish polishing complete including 20mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm thick jointed in grey cement slurry mixed with pigment to match the shade of the slab as in skirting dado incl rubbing and mirror finish polishing complete including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm thick area 0.11 to 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement te match over and including 15mm thick screed bed of CM 1:6 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm thick area 0.06 to 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement te match over and including 15mm thick screed bed of CM 1:6 complete all as specified and directed.

All as per item No. 46 but as in skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10mm thick backing coat of rendering with CM 1:4 complete all as specified and directed.

S&F Glazed ceramic colour tiles (300x200x7mm thick) on dado & skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering with rough finished in cement mortar 1:4 to received tile complete all as specified and directed.

M&L for 25mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windows cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with shade of granite complete all as specified and directed.

Material and labour for 100mm thick Plain Cement concrete type D2 1:4:8 (40mm graded aggregate) for base in floor finished even and fair complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clan and washing down with water to remove dust complete all as specified and directed.

Material and labour for 15mm thick Cement Mortar (1:4) screed bed or bedding layer for laying floor finishes over & incl brushing neat cement slurry with 3.0 Kg of cement per Sq. meter complete all as specified and directed.

Material and labour for vitrified ceramic tiles light shade 8 to 10mm thick (square rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material and labour for vitrified ceramic tiles light shade 8 to 10mm thick (square rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM (1:4) for laying skirting finishes complete all as specified and directed.

Taking down cement plaster of any description on bricks or stone walls, etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block (rubber moulded)any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade with proper jointing, pointed with grey cement and pigment complete all as specified and directed.

S&F Steel tubular trusess, purlins, rafters including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinay and counter sunk) forming holes, without any attachment of Fe 410W (Gde-E -250) Quality 'A' complete all as specified and directed.

S&F Mild steel screw bolt (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each exc 5cm but n.exc 10cm long dia 11 to 15mm necessary fitting complete all as specified and directed.

S&F Prepainted galvalume aluminium zinc coating steel based corrugated steel sheet 0.50mm thick of and colour having tensile strength of 550 Mpa as in roof coverings/ claddings to wall, fixed with self tapping screws complete all as specified and directed.

S&F Prepainted galvalume aluminium zinc coating steel based plain steel sheet 0.50mm thick of and colour having tensile strength of 550 Mpa as in roof coverings/ claddings to wall, fixed with self tapping screws complete all as specified and directed.

S&F for 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screw complete all as specified and directed.

S&F for 0.63mm thick Plain, galvanised mild steel sheeting as in ridges hips, valley gutters drip or as in eaves boarding complete all as specified and directed.

Steel windows with side hung shutters including box type hinges with steel handles, 2 Nos steel tower bolts 100mm long peg stay complete with glazing bars, dovetailed or welded, including locking arrangements complete all as specified and directed.

All as per item No. 64 above but without glazing bars

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and or riveted, or forged in to spikes; framed guard bars; similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc of size 125X60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed.

M&L Flush shutters, 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides including 6/8mm thick polished teak wood lipping around the door properly fixed complete all as specified and directed.

M&L 2nd class hard wood, 35 mm thick, glazed and skeleton shutter, divided into square, with plain, chamfered or rounded mitered and , any number of panels, prepared to receive glass, gauge etc. edges of frames chamfered or round size of numbers of shutters as specifed in SSR Part-I section clause 8.24 (a) complete all as specified and directed.

M&L for 10mm thick cement plaster in CM 1:6 on brick wall or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick cement plaster in CM 1:3 on concrete surfaces in ceiling finished fair and even complete all as specified and directed.

M&L for 10mm thick cement plaster in CM 1:3 on concrete surfaces in roof slab finished fair and even complete all as specified and directed. Note -WPC shall be measured and paid separetly.

M&L rendering 15 mm thick cement plaster in two layer each of 10+5 mm thick on fair faces of brick wall or condrete surfaces in CM (1:3) & water proofing compound mixed with second layer @ 3% finished even and smooth using extea cement. Note -WPC shall be measured and paid separetly.

Supply only WPC complete all as specified and directed.

S & F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010) complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified and directed.

M&L for providing plain cement concrete 1:3:6 type C0 (using 12.50 mm graded stone aggregate) as in filling hollow of pressed steel frame and hold fast etc. complete all as specified and directed.

M&L Plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in bed blocks, coping, cills, steps, kneelers, bed plates, apex stones kerbs benching and similar work including necessary form work complete all as specified and directed.

M&L MS work as in hold fasts, bands, straps, wall ties, plain angle cleats and similar articles including welding and all necessary labour conforming to Fe 250 Gde-E-165 complete all as specified and directed.

Mild steel sliding door bolt, 300 mm, plate type, stove enameled black, with bright bolt not less than 12 mm dia, with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed to door with over all length 150mm with rubber bush complete all as specified and directed.

S&F Galvanized mild steel wire cloth 0.46 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

S&F Mild steel 300mm size ordinary rat tail rod pattern springs including roller and roller plate complete including necessary fitting complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 200mm long complete all as specified and directed.

S&F Aluminium handle cast type anodized of size 125mm complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size, complete all as specified and directed.

Supply and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors or laid in trenches . all as specified and directed.

All as per item No. 88 here in before but 20 mm bore.

All as per item No. 88 here in before but 25 mm bore.

Supply and fix, as in repair for vitreous china wash down water closet pan of padestel pattern white with P or S trap including Plastic water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device jointed in white cement complete all as specified & directed Make JAQUAR Cat part No LYS-WHT-38201 Cistern with cistern fittings for 38751P180UFSM & 38751S250UFSM set or equivalent make as approved by GE.

Supply and Fix health faucet with or without swivel jonts of any colour for fixing with 15 mm boreconnecting pipe minimum 1 mtr long with hanger of PTMT any colour incl all necessary fitting & fixtures complete all as specified & directed Make Hindware Cat part No F-160027 or equivalent make as approved by GE.

Supply and Fix chromium plated Swivel shower roses with arm, 125 size including fixing to steel pipe or union complete all as specified.

S&F PVC valve less syphonic action type of capacity 10 ltrs, low level flushing cistern, white with inlet, ball valve float and handle including brackets complete all as specified and directed.

Supply and fix vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

Supply & fix Vitreous China urinals, half stall type flat back of size 465 x 355 x 265 mm white (minimum), complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

Supply and fix 15 mm bore bib taps, chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix 15 mm bore pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe complete all as specified and directed.

Supply and fix, 15 mm bore stop valve, cast copper alloy, screwed down high pressure, with crutch or butterfly handles fixed to pipe unions complete all as specified and directed.

Supply and fix, 20mm bore stop valve, cast copper alloy, screwed down high pressure, with crutch or butterfly handles fixed to pipe unions complete all as specified and directed.

Supply & fix soap dish, any type fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F gun metal globe, or gate valves of size 25mm bore with iron wheel head, screwed at both end for iron pipe and fixed complete all as specified and directed.

S&F gun metal globe, or gate valves of size 20mm bore with iron wheel head, screwed at both end for iron pipe and fixed complete all as specified and directed.

S&F PVC connections 15mm dia size with PTMT nuts of length 450mm complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L for cutting holes to existing man hole for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in CM 1:2:4 type B1 smooth finished, and removing benching as required complete all as specified and directed.

S&F PVC (SWR) Pipe 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floor or fixed to walls with suitable size of clamps & nuts bolt complete all as specified and directed.

S&F PVC (SWR) Pipe 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floor or fixed to walls with suitable size of clamps & nuts bolt complete all as specified and directed.

M&L PCC 1:3:6 type C2, using 40mm graded crushed stone aggregate as in PCC bed to drain pipes 150mm dia including packing under and hauncing against the sides of pipes after the pipes are laid and tested completed all as specified and directed.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly-nuts, flange end bedded in red lead, cement and other other end fixed completed all as specified and directed.

S&F PVC (SWR) bends 75 mm bore any radius complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore any radius complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm complete all as specified and directed.

S&F PVC waste coupling for 32 mm bore waste pipe in WHB complete all as specified and directed.

S&F PVC waste pipe 32 mm bore for WHB 900 mm long complete all as specified and directed.

S&F chromium plated tubular towel rail 20 mm dia 60 cm long, with brackets complete all as specified and directed.

Supply and fix 32mm Brass chromium plated trap 'P' or 'S' pattern for wash basin with inlet and outlet screwd for pipe or connections, and with one cleaning cap and fixing complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap CP with grating including jointing to waste fixed in PCC 1:2:4 type B1 complete all as specified and directed.

Preparation of new or untreated surfaces of wood or wood based surfaces of any description exc.10 cm. in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Preparation of new or untreated steel surface of any description exc. 10 cm. in width or girth and applying two coats of synthetic enamel paints, over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces in walls and applying three coats of white wash complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying two coats of exterior wheather coats (as per manufacturers instruction) (Apex Ultima) of M/s Asian make or equivalent of M/s Berger M/s Shalimar M/s Neroloc over & incl a coat of wall putty 3mm thick complete all as specified and directed.

M&L preparation and applying two coats of oil emulsion (distemper) over a coat of primer on new plastered surfaces of walls over a coat of wall putty 3 mm thick including preparation of surfaces complete all as specified and directed.

PART-II (E/M WORKS) M&L for point wiring with single core PVC insulated cable of size 1.5Sqmm nominal area with multi-stranded copper conductor, 1100V grade FRLSH drawn through and including PVC non metatllic concealed conduit of appropriate size & 1.8mm wall thickness with all fitting and accessories including GI sunken box alongwith hylum sheet of required thickness for mounting switches/sockets etc of suitable size including 1.5Sqmm PVC insulated unsheathed single core copper conductor earth continuity wire connected to common earth dolly with proper colour coding for one light point/fan point/bell point complete all as specified and directed.

All as per item No. 125 above but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

All as per item No. 125 above but for One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No. 125 above but with stranded copper conductor 2.5 Sq mm (nominal area), two single core, PVC insulated and unsheathed cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed.

Supply and fix switch piano flush type button single pole one way 5 Amps complete all as specified and directed.

Supply and fix socket outlet 3/5 pin 5 Amps flush type complete all as specified and directed.

Supply and fix switch socket outlet 3 pin 5 amp and 5/6 pin 15 Amps 2 in 1 universal plate complete all as specified and directed.

S & F ceiling fan regulator socketed, step type, flush type heavy duty suitable to work on 230 volts AC supply complete all as specified and directed.

Supply and fix lamp Angular holder insulated body with back plate suitable for batten fittings complete all as specified and directed.

Supply and fix wall mounted LED batten Box type 22 watt with LED tube rod prewired complete all as specified and directed. Make. Havells, Product Code : REGALBATTENT8UPTO1X22WDSBSWH & CRYSTAL1213T8DSTL20WLED865SGLASS or equivalent make of Philips/Bajaj/Wipro/Syska LED/Crompton Greaves/M/s Surya Roshni Limited /M/s Jaquar & Company Pvt Ltd

Supply and fix street/bldg security light LED luminaire 20 watt IP 66 LED lamp, driver etc, including service bracket made cut of 25mm bore GI pipe medium grade fixed with MS clamps, nuts and bolts with all accessories complete all as specified and directed. Make:- Havells type 20W LED, Cat No. ENDURAPEARLSL20WLED757SASYTOPCMP or equivalent make of Philips/Bajaj/Wipro/Syska LED/Crompton Greaves/M/s Surya Roshni Limited /M/s Jaquar & Company Pvt Ltd

Supply and fix ceiling fan complete with all accessories 230 V, 1200 mm sweep. BEE 5 star rated with regulator complete all as specified and directed. Make:- Usha Model : Energia 5 Star or equivalent make of Havells/Crompton Greaves/ Khaitan/Bajaj/Orient

S & F plastic body exhaust fan, AC single phase, 240 V of size 250 mm sweep with louvers including necessary connection of flexible copper cable from ceiling rose complete all as specified and directed. Make:- Havells 250mm Crisp Air LX or equivalent make of Crompton Greaves/ Khaitan/Bajaj/Orient

Supply and fix sheet metal enclosure powder coated single phase DB SPN for fixing of MCBs, 8 ways double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated single phase DB SPN for fixing of MCBs, 4 ways double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed.

Supply and fix MCB SP 240 volts, 50 Hz capacity 6-32 Amps complete all as specified and directed.

Supply and fix MCB SPN 240 volts, 50 Hz of capacity 40 Amps complete all as specified and directed.

Material and labour for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth lead wire 4 mm dia by means of galvanized iron or steel bolts, nuts, check nuts and washers, and connected to equipments as directed, including funnel with GI med grade watering pipe 20 mm bore, wire mesh, charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with concrete pit in PCC 1:3:6 type C1, 50 mm thick pre cast RCC 1:2:4 type B1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar, GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance not exceeding 50 m and necessary testing complete all as shown on electrical plate No. 3 of MES Schedule 2009, Part-I complete all as specified and directed.

Supply and laying connecting and testing XLPE insulated PVC sheathed armoured LT electric power UG cable (heavy duty with stranded aluminium conductor) of size 25 sqmm 2.0 core,1100 volts (Earthed) grade, conforming to IS 7098 (Part-II) laid thorught duct/pipe in trenches etc with cable glands & suitable size of aluminium lugs complete all as specified and directed.

Supply and spread dry sand in trenches as sand cushioning to under ground cable for protection with fine river sand and provide reqd cover after punning down complete all as specified and directed. Note : Thickness of sand cushion after punning down will be measured and paid.

Material and labour for laying of bricks locally available sub-class 'B' brick (old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the directon of cable complete all as specified and directed.

Supply and laying GI tube light grade 40mm bore with fitting laid in trenches of for road crossing for protection of LT underground cables complete all as specified and directed.

M/S. N.A.BARBHUIYA

SURANA CORPORATION

m/s builders and suppliers

M/S R A ENTERPRISE

MAGADH TRADING

M/S MOLOY KUMAR DEY