Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹3.8 CrAdmitted-Finance | +0.00% | ₹3.8 Cr | L1 | Admitted-Finance |
| 2 | L2₹3.9 CrAdmitted-Finance 232 RAJENDRA NAGAR STREET 7 KAULAGARH ROAD DEHRADUN | +0.00% | ₹3.9 Cr | L2 | Admitted-Finance |
| 3 | L3₹4.1 CrAdmitted-Finance 27 46 INDER ROAD DALANWALA DEHRADUN | DEHRADUN | UTTARAKHAND | 248001 | +0.00% | ₹4.1 Cr | L3 | Admitted-Finance |
Tender Value
₹3.8 Cr
EMD Value
₹7.7 L
Closing Date
5 Mar 2026, 1:00 pmClosed
Superintending Engineer, EDC(U),Dehradun
office of the Superintending Engineer, EDC(U),Dehradun
New service connection and associated line for EV Charging Station under EDD South,18 EC Road Dehradun
2026_UPCL4_92000_1
Tender No.49/EDC(U)/2025-26
Open Tender
Electrical Works
45 days
as per tender specification
as per tender specification
4 documents required · 4 mandatory
₹17,700
Executive Engineer, ETD(U),Dehradun
₹7.7 L
9 Apr 2026
19 Feb 2026
5 Mar 2026
20 Feb 2026
5 Mar 2026
21 Feb 2026
(A) 33 KV Underground Transportnagar
(B) EV CHARGING S/S
Item Rate BoQ
BoQ_Ver3.0
Name of the Bidder/ Bidding Firm / Company :
(A) 33 KV Underground Transportnagar (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) Note:-GST Extra as per applicable
NUMBER #
Decentralized Material
33 KV CABLE END TERMINATION J/KIT FOR 3CX400 SQMM CABLE (O/D)
33 KV CABLE END TERMINATION J/KIT FOR 3CX400 SQMM CABLE (I/D)
33 KV STRIGHT THROUGH JOINT KIT FOR 3CX400 SQMM CABLE
EARTH WIRE CLAMP FOR SP-55 WITH N/B
CLAMP FOR STP POLE
STAY CLAMP FOR SP-55
AL LUGS OF SIZE UPTO 400 SQMM
CABLE HOLDING CLAMP FOR SP -55
MS BOLTS & NUT WITH WASHER
LA CLAMP
EARTHING STRIP 50X5 MM
DANGER BOARD
33KV 630 AMP ISOLATOR VERTICAL TYPE
630A ISOLATOR CLAMP
G.I. PIPE FOR POLE MOUNT CABLE (6 DIA.)
LABOUR CHARGES
GROUND-PENETRATING RADAR (GPR) FOR ENTAIR ROUTE BEFORE STARTING THE ROUTE
CARTAGE OF OTHER STOCK MATERIAL (OTHER THEN POLES) BY VEHICLE FROM STORE CENTER TO NEAREST CONSTRUCTION SITE STORE INCLUDING LOADING AND UNLOADING AT BOTH ENDS. (0-20KM)
CARTAGE OF ST-55 POLE POLE FROM STORE CENTRE TO CONSTRUCTION SITE WITH LOADING,UNLOADING AT BOTH POINTS AND PROPER STACKING (0-20 KM)
MANNUAL CARTAGE OF MATERIAL UNLOADING POINT TO WORK SITE ( 0 TO 0.5 KM) (A) STOCK MATERIAL
MANNUAL CARTAGE OF MATERIAL UNLOADING POINT TO WORK SITE ( 0 TO 0.5 KM) (B) STP SP-55 POLE
EXCAVATION OF EARTH FOR POLE PIT OF SIZE 0.9X0.6X1/6 OF FULL LENGTH OF POLE FOR ERECTION OF POLE IN ALL TYPE OF SOIL INCLUDING PROPER DRESSING OF SIDES AND RAMMING OF BOTTOM INCLUDING GETTING OUT THE EXCAVATED SOIL AND DISPOSAL OF SURPLUS EXCAVATED SOIL AS DIRECTED COMPLETE WORK
ERECTION OF FOLLOWING SINGLE SUPPORT POLE IN PROPER LEVEL AND ALIGNMENT ALONG WITH FIXING OF ALL ACCESSORIES,LIKE TOP CHANNEL & CLAMP AS PER RESPO CONSTRUCTION MANUAL. (A) STP POLE SP-55
ERECTION OF FOLLOWING DOUBLE SUPPORT POLE IN PROPER LEVEL AND ALIGNMENT ALONG WITH FIXING OF ALL ACCESSORIES,LIKE TOP CHANNEL & CLAMP AS PER RESPO CONSTRUCTION MANUAL. (A) STP POLE SP-55
GROUTING OF POLE IN SIZE 0.45X0.45X1/9 OF THE SUPPORT IN CC RATIO 1:4:8(1 CEMENT:4 GRADED STONE 20MM NOMINAL SIZE : 8 COARSE SAND) BLOCK INCLUDING COSTOF CEMENT,SAND ALIGNMENT,LEVELING AS PER RESPOCONSTRUCTION MANUAL.
MUFFING OF POLES SIZE 0.45 CMX0.60 CM RADIOUS WITH CC 1:3:6 (1 CEMENT : 3 COARSE SAND : 6 GRADED STONE 10 MM NOMINAL SIZE) BLOCK SIZE 45 CM HEIGHT FROM GROUND LEVEL INCLUDING COST OF CEMENT, STONE AND SAND ETC.
PAINTING OF NEW POLES WITH CHANNEL INCLUDING ONE COAT PRIMER AND TWO COAT SILVER PAINT AND RED ASIAN PAINT OF SUPERIOR QUALITY ON UPPER SIDE OF POLE
EXCAVATION OF PIT FOR STAY SET
FIXING AND GROUTING OF STAY SET INCLUDING DIGGING OF PIT IN SIZE OF CC 1:4:8 (0.3X0.6X0.6) MTR INCLUDING NOZZELING, FIXING, TENSIONING AND TIGHTENING COMPLETE.
GROUTING OF STAY SET
FIXING OF MS EARTH ROD INCLUDING EXCAVATION, INSERTING OF EARTH ROD IN SOIL AND CONNECTION OF EARTH WIRE
LAYING OF HDPE PIPE FOR 33 KV CABLE WITH TRENCHLESS TECHNOLOGY INCLUDING COST OF SUITABLE OUTER DIA MATERIAL GRADE PE80/PN6 (AT A DEPTH OF 1.2 MTRS) HDPE PIPE
SUPPLY AND FIXING OF 160 MM DIA PE80 HDPE PIPE HIGH-DENSITY POLYETHYLENE PIPE
MAKING OPEN TRENCH IN ROCKY SOIL FOR 33 KV CABLE LAYING AT 1.2 MTR DEPTH BELOW GROUND LEVEL
SUPPLY AND FIXING OF GI PIPE AT POINTS OF ROAD CROSSING, CABLE RISING ETC
LAYING OF 33 KV CABLE IN HDPE PIPE, GI PIPE, LOOP ETC
SUPPLY AND FIXING OF SPECIAL EARTHING FOR CABLE AT DIFFERENT POLE STRUCTURE BY 450X450X10MM G.I. PLATE VERTICALLY 3M BELOW THE GROUND LEVEL WITH ALTERNATE LAYERS OF CHARCOAL & SALT ATLEAST 200MM THICK AROUND CONNECTED WITH G.I STRIP RUNNING TILL TOP OF POLE COMPLETE.
FILLING & FIXING OF 33KV END TERMINATION CABLE J.KIT (O/D & I/D)
FILLING & FIXING OF 33KV END TERMINATION CABLE J.KIT (ST TH)
FIXING OF MS CHANNEL, ANGLE AND ALL ACCESSORIES ON EXISTING/NEW SINGLE POLE
FIXING OF MS CHANNEL, ANGLE AND ALL ACCESSORIES ON EXISTING/NEW DOUBLE POLE
SUPPLY AND FIXING OF RCC ROUTE MARKER
SUPPLY AND FIXING OF DANGER/NUMBER/NAME PLATE
LAYING/SAGGING/JUMPERING/STRINGING OF ACSR CONDUCTOR
TESTING OF CABLE BEFORE CHARGING
MOUNTING & FIXING OF LIGHTNING ARRESTOR SET(3 NOS) ON DOUBLE POLE STRUCTURE INCLUDING MAKING ALL CONNECTION BY G.I STRIP SIZE 50X5 MM TO EARTH POINT COMPLETE WORK (INCLUDING COST OF G.I STRIP)
SUPPLY AND ERECTION OF LA EARTHING
ERECTION AND FABRICATION OF 33KV ISOLATOR VERTICAL TYPE IN PROPER ALIGNMENT FOR SMOOTH OPERATION
Item Rate BoQ
BoQ_Ver3.0
Name of the Bidder/ Bidding Firm / Company :
(B) EV CHARGING S/S (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) Note:-GST Extra as per applicable
NUMBER #
Decentralized Material
GI Pipe 2" dia., 2.5 mm. thickness, 6 mtr. Long for isolator handle
M.S. Bolt & Nut Off size
MS Plate 225x225x8 mm.
MS Plate 400x400x8 mm.
G.I. Strip 40x6 mm.
G.I. Strip 65x6 mm.
Stay clamp for ST Pole
Clamp of required size for holding cable supporting angle, pipe, cable & bus isolator handle on double pole & bus bar gantry
Bracing Clamp for ST Pole
Connector for LA suitable for panther
M.S. bolts & nut with washers.
PG clamp Panther to Panther
P.P. & Clamps for S.T. Pole SP-55 with nut & bolts
P.P. & Clamps for S.T. Pole SP-72
For Isolators suitable for dog/weasel
For Isolators suitable for panther
Disc insulator Polymer,120 KN, B & S type
G.I.pipe 40/50 mm out.dia. & thickness 4/5 mm, 6 mtr. Long for making opearting mechanism for vertical bus isolator
33 KV Danger board with clamp
GI pipe 4" dia. 3mtr long ( for double pole & bus bar gantry)
Connecting clamp for Panther Conductor
150W, HPSV/ LED lamp with control gear & mounting accessories
250W, HPSV/ LED lamp with control gear & mounting accessories
GI pipe 6" dia, 3mtr long
Perforated tray 300 mm width for cable trench
Connector for Fuse setsuitable for dog/weasel
Connector for LA suitable for dog/weasel
Insulators for holding earthing strip of lightening arrestor & transformer neutral
LT XLPE Cable 1Cx630 sq.mm.
Cable jointing kit outdoor type suitable for 3x50 sq. mm. XLPE cable 33 KV.
Iron clad 30 Amps switch on the ST pole.
33 KV, Line isolator (Vertical Type)
Wire mesh fencing with 4 mtr. & 1 mtr. Wide gate duly painted on both sides
Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)
MS Bar, 12 mm Dia for Steel reinforcement
Isolator Clamp
33 KV Bus Bar Isolator
Stone Pad 300x300x75
Connector for VCB suitable for panther
Instruction board 3"x21/2 of polyflex board moulded with frame duly painted & writing
Maximum & minimum display board of size 5' x 3' of polyflex board moulded with frame duly painted & writing
Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted & fixing at S/s with C.C. 1:4:8
single line diagram board of size 2 1/2x 1 1/2 polyflex board with frame,duly painted & writing
Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet and Duly painted with red color including cost of all material, fabrication etc. complete work
Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required
Metal Fire bucket Filled with sand
Connector for CT/PT suitable for panther/dog
Perforated tray 400mm width for cable trench
Perforated tray 100 mm width for cable trench
Clamp of required size for holding cable supporting angle, cable & isolator handle
Clamp of MS flat 75x10 mm. of suitable size for fixing of MS channels
Clamp of MS flat 50x6 mm. of suitable size for fixing of MS angles
2 MVA, 33/.433 KVA T/F
Connector for Fuse set suitable for panther
Connector for T/F suitable for panther
Connector for T/F suitable for LT side
Connector for station transformer suitable for dog/weasel
33/0.433 KV, 63 KVA Station Transformer
Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.
Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.
LV switchgear consisting of 3200A, 4P microprocessor based ACB and 04 Nos 630 A microprocessor controlled MCCB (d) IP54 outdoor enclosure and all accesories / protections as per specification.and mounting structure as per specification
connector suitable for LT XLPE Cable 1Cx630 sq.mm.
LABOUR CHARGES
Excavation of earth
Earthfilling in yard
Cement concreting of Double pole 1:4:8
Brick work in 1:4
Cement plaster in 1:4
Making cable trench.including fabrication, fixing of MS angle 50/40X6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.trench size of 125x1x1 (Lxbxh)
Fabrication charges of structure as per approved drawing
Errection of ST Pole SP-10 and fitting of accessories.
Erection of Double pole complete with all fittings, accessories, stays & earthing.
Cement concreting of Double pole 1:4:8, 2x(.45x.45x2.1)
Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint
Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.
Erection of 33 KV fuse set on double pole
Fixing and erection charges of Lightening arrestor
Filling of cable jointing kit 33 KV outdoor type
Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8
Erection charges of structure
Fixing and erection of CT
Erection charges of Isolator complete by fabrication, assembeling, fixing of operating handle, pins etc for smooth operation of the isolator. (Vertical)
Cartage of pannels & Circuit breaker from road side to SGR
Erection of transformer by fixing all accessories, tank, filling of transformer oil etc.
Laying of XLPE Al. conductor 4x10 mm Power Cable in trench & back filling of sand.
Erection charges of Isolator complete by fabrication, assembeling, fixing of operating handle, pins etc for smooth operation of the isolator including grauting. (Horizantal)
Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..
Straightening and laying of Earth mat of 32 mm M S round 0.6 mtr deep in mixed soil according to drawing or as per UPCL direction or/and as per site requirement. Making T-joints, cross joint and Lap joints by welding of M S round bar together using cleats of MS Angles 65x65x6 mm, chipping the slag and painting of the joints with black bitumen paint (including supply of paint) to avoid rusting. Cutting & making electrode 2.5 mtr long with conical pointed bottom and driving of the electrode remains 450 mm below ground level. Backfilling of soil in trenches, ramming and leveling of trench properly after completion of eartmat and earthing work is complete. Making of Delta/Bridge earthing for structure/panels i.e. LA, 11 KV panels, ACDB, DCDB, Neutral of power & station transformer.
Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.
Earthing of structures using G.I. strips including strengthening, cutting, bending & welding with structure and equipments.
Erection of 24 V Battery set Maint. Free
Laying of LT Cable in trench 1Cx630 sq.mm.
Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.
Erection charges of isolator structure
Erection of 24 V Battery charger with boost & trickle charge
Laying of 33 KV KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.
Erection of DCDB 24 V
Erection of ACDB
Erection charges of Bus Gantry
Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.
Erection of Name plates, instruction board, SLD, Max., Min. board etc.
Instalation/Mounting of Fire Extinguishers
Shifting of transformer from road side to transformer plinth through chain pully, lift pully and slippers etc.
Fixing and erection of equipments.
Erection of 33/0.433 KV station transformer on double pole with all accessories complete work
Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..
Making electrical connection of panels by control wiring complete with & VCB etc.
Plinth Work for Breaker
Erection of all lighting equipment, other than pole & its accessories
Gravel pitching of size 1/2" to 3/4" (20x30x1)
Please Enable Macros to View BoQ information
PQR PART-1 SHEET For Tender No. 49/EDC(U)/2025-26
PART -I OPENED ON DATE 05-03-2026 AT 16:00 HRS
Full Postal Address of Tenderers (Head Office)
Works Address
Email:- ID
Singature of Bidder
stage.html
html • 0.03 MB
technical_108943.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.23 MB
Coverpage49.pdf
Tender Documents • 0.18 MB
BOQ_108943.xls
BOQ • 0.40 MB
Tenderdoucments49PDF2.pdf
Tender Documents • 1.55 MB
PQR492025.xls
Tender Documents • 0.03 MB
Tecnicalspecification49.pdf
Tender Documents • 0.34 MB
Download all tender documents and submit your bid