REPAIR AND POLISHING OF WOODEN FURNITURE UNDER GE (N) BINNAGURI

Amount

Peg Set of Six Drawing No FD-80(M)/DB-4069

(a) Taking out old damaged decayed TW Plank form its position and S&F new TW Plank in the same position as per existing shape and size made out of 19mm x 75mm section well seasoned teak wood timber and Key plate including one coat of french polish over wood filler whereever reqd complete all as specified, directed and shown or drawing.

(b) Taking out old damaged / decayed pegs from its position and S&F new pegs as per existing shape and size made with brass chromium plated fixed with suitable screw, complete all as specified & as directed and as shown on drawing.

(c) M&L for applying French Polish one or more coat till glossy finish achieved after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Stool Dressing Drawing No FD-282

(a) Taking out old damaged / decayed leg from its position and S&F new leg in the same position made out of well seasoned ‘teakwood’ timber complete all specified and as directed and as shown on drawing.

(b) -Ditto- all as per item Ser No 2(a) above but for long rail and –ditto-.

(c) -Ditto- all as per item No 2(a) above but short rail –ditto-

(d) -Ditto- all as per item No 2(a) above but stiffener and –ditto-

(e) Taking out old unserviceable / worn out plastic cane from seat fixed and re-canning the same with new white plastic cane 2mm wide half round (oval) type best quality for weaving and 4mm wide for bordering (Godrej pattern) complete all as specified and as directed and as shown on drawing. Make : Ajoy/primer/Aryan)

(f) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing

Table 900*600*760 mm with drawer wooden Drawing No FD-41(M)/FD-283

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged/decayed long rail from its position and S & F new long rail in the same position as per existing shape and size made out of well seasoned ‘hard wood Teak including applying one coat of French polish over wood filler wherever required complete as specified and as directed and as shown on drg.

(c) -Ditto- all as per item Ser No 3(b) above but for short rail and –ditto-.

(d) -Ditto- all as per item Ser No 3(b) above but for leg and –ditto-.

(e) -Ditto- all as per item Ser No 3(b) above but for leg stiffener and and –ditto-.

(f) Taking out old damaged/decayed drawer from its position and S & F new drawer as per existing shape and size made out well seasoned ‘hard wood’ timber complete all as specified and directed and as shown on drg.

(g) Taking out old damaged / decayed handle from shutter and S&F new Square 'D' type 100 mm long (4"), steel handle as approved the same place, complete all as specified & as directed by Engr-in-charge.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Table 900*900*760mm wooden Drawing No FD-88(M)/FD-291

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged/decayed rail (front/back/sides) from its position and S & F new rail in the same position as per existing shape and size made out of well seasoned hard wood ‘Teak' including applying one coat of French polish over wood filler wherever required complete as specified and as directed and as shown on drg.

(c) -Ditto- all as per item Ser No 4(b) above but for leg and –ditto-.

(d) S&F wooden corner of size 100x 100 x 35mm thick teak wood bracket corner fixed to place of joining legs with top rails by suitable wood screw complete all as specified and directed by engr-in-charge .

(e) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Table Dining Six Persons Drawing No FD-239/FD-273

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged / decayed long rail from its position and S&F new long rail in the same position as per existing shape and size made out well seasoned ‘Teakwood’ timber including applying one coat of French polish over wood filler over exposed new timber surfaces compete all as specified & as directed and as shown on drawing.

(c) -Ditto- all as per item No 5(b) above but short rail and –ditto-.

(d) -Ditto- all as per item No 5(b) above but leg and –ditto-.

(e) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Chair Writing Drawing No FD-20(M)/FD-280: Repairs to Chair Writing for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs, rails, stiffiners, Hand rest etc and supply and fixing with new items of well seasoned hard wood (Teak) and minor repairs if any complete all as specified and shown on drawing.

(a) Front legs.

(b) Rear legs.

(c) Rails (both side, front/rear).

(d) Leg stiffeners .

(e) Back rest stiffener.

(f) Arm rest (left/right).

(g) Taking out and removing old unserviceable worn-out of plastic cane from chair writing and recanning the same with white new plastic cane half round oval type 2mm wide, 0.4mm thick for weaving and 4mm wide for boarding (Godrej Pattern) complete all as specified and as directed and as shown on drg.

(h) Taking out of all old unserviceable PVC shoes and S & F new hard PVC shoes with screws as approved, complete all as directed and shown on drg.

(j) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Chair Dining Drawing No FD-16(M)/FD-279/FD-1105: Repairs to Chair dining for the following :- Removing old unserviceable fitting and fixture of Chair dining without disturbing to the other parts such as legs, rails, stiffiners etc and supply and fixing with new items of well seasoned HW (Teak) and minor repairs if any complete all as specified and shown on drawing.

(a) Front legs.

(b) Rear legs.

(c) Seat rails (front / back, both side).

(d) Leg stiffeners.

(e) Back rest stiffeners.

(f) Taking out and removing unserviceable worn out plastic cane from seat of chair dining and re-canning the same with new white plastic cane of 2mm wide, 0.4mm thick half round (oval type) for weaving and 4mm wide for bordering as per Godrej pattern complete all as specified & as directed and as shown on drawing.

(g) Taking out of unserviceable hard rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws as approved, directed and shown on drg.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Chair Wooden Drawing No FD-56(M)/FD-225: Repairs to Chair wooden bottom without arms for the following :- Removing old unserviceable fitting and fixture of Chair wooden bottom without disturbing to the other parts such as legs, rails, stiffiners etc and supply and fixing with new items of well seasoned hard wood (Teak) and minor repair if any complete all as specified and shown on drawing.

(a) Front legs.

(b) Rear legs.

(c) Side rails (Right/Left/Front/Rear).

(d) Leg/Bottom stiffeners.

(e) Back rest stiffeners.

(f) Taking out old damaged/decayed ply wood seat from its position and S & F new seat ply of 6mm thick BWR grade commercial type to the same position as per existing shape and size complete all as specified and as shown on drawing.

(g) Taking out of old unserviceable hard rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws to the same position complete all as specified and as shown on drawing.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Chair Easy Drawing No FD-17(M)/FD-229: Repairs to Chair Easy for the following :- Removing old unserviceable fitting and fixture of Chair Easy without disturbing to the other parts such as legs, rails, stiffiners, Hand rest etc and supply and fixing with new items of well seasoned hard wood (Teak) and minor repair if any complete all as specified and shown on drawing.

(a) Front legs.

(b) Rear legs.

(c) Rails of back frame (top/bottom/sides).

(d) Rails of bottom frame (front/rear/left/right).

(e) Arm rest (left/right).

(f) Taking out and removing all unserviceable worn out plastic cane from seat and back of chair easy and re-canning the same with new white plastic cane 2mm wide, 0.4mm thick oval type in seat and back by weaving and 4 mm wide for bordering complete all as specified and shown in drawing.

(g) Taking out of old unserviceable hard rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws to the same position complete all as specified and as shown on drawing.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Hat Stand Drawing No FD-233

(a) Taking out old broken / decayed mirror from its position and S&F new 5.5mm thick looking mirror of the same as per existing shape and size complete all as specified and as shown on drawing.

(b) Taking out old damaged/decayed wooden edging (top/bottom/sides) from its position and S&F new edging in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber 35mm x 6mm thick including applying one coat of French polish over wood filler over exposed new timber surfaces complete all as specified and as shown on drawing.

(c) Taking out old damaged / decayed back ply from its position and S&F new 4mm thick plywood BWR grade including one coat french polish to new surface complete all as specified & as directed and as shown on drawing.

(d) Taking out old damaged / decayed front ply from its position and S&F new 4mm thick plywood BWR grade with 0.9mm thick sunmica one side teak face complete all as specified & as directed and as shown on drawing.

(e) Taking out old damaged / decayed pegs from its position and S&F new pegs as per existing shape and size made with brass chromium plated fixed with brass screw, complete all as specified & as directed and as shown on drawing.

(f) M&L for applying French Polish to Hat stand with one or more coat till glossy finish achieved to match with existing surface (wood/woodbase) and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table Peg Drawing No FD-384

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with 0.9mm thick sunmica decorative natural teak glossy finish including wooden beading all round complete all as specified and directed and shown on drawing.

(b) Taking out old damaged / decayed long rail (front/rear) from its position and supply of fixing new long rail as per existing shape and size made out of well seasoned hard wood ‘Teak' complete all as directed and shown on drawing.

(c) All as per item No 11(b) here in before but for short rail (right/left) and ditto.

(d) All as per item No 11(b) here in before but for leg and ditto.

(e) All as per item No 11(b) here in before but for stiffener and ditto.

(f) S&F PVC shoes in repair to bottom of leg as approved quality Complete all as specified and shown on drg.

(g) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Almirah Mess Utensil Drawing No FD-93(M)

(a) Taking out old damaged/ decayed legs from its position and S&F new leg as per existing shape and size in the same position made out of well seasoned `teakwood timber including applying one coat of french polish over wood filler complete all as specified & as directed and as shown on drawing.

(b) All as per item Ser No 12(a) above but for bottom long rail.

(c) All as per item Ser No 12(a) above but for bottom short rail.

(d) Taking out old unserviceable/ decayed back ply from its posn and S&F new back plywood in the same posn of 9mm thick commercial grade BWR type as per the existing shape and size including applying one coat of french polish over wood filler complete all as specified & as directed and as shown on drawing.

(e) Taking out old damaged/ decayed door shutter (Right/Left) from its position and S&F new shutter made out of 18 mm thick plywood BWR grade with 0.9mm thick sunmica teak face glossy finish laminated on outer surface and another surface with applying french polish including wooden beading on all arround the shutter and fixed with stainless steel hinges 75mm long (Type E-II) with suitable screw, complete all as specified & as directed and as shown on drawing.

(f) All as per item ser No 12(e) above but for cabinet top shelf and -ditto-.

(g) Taking out old damaged/ decayed sides (Right/Left) from its position and S&F new sides (Left/right) made out of 19mm thick well seasoned hard wood including applying one coat of french polish over wood filler complete all as specified & as directed and as shown on drawing.

(h) All as per item ser No 12(g) above but for Top of almirah and -ditto-.

(j) All as per item ser No 12(g) above but for inner shelf and -ditto-.

(k) All as per item ser No 12(g) above but for Bottom base and -ditto-.

(l) Taking out old damaged / decayed handle from shutter and S&F new Square 'D' type 100 mm long (4"), steel handle as approved the same place, complete all as specified & as directed by Engr-in-charge.

(m) S&F in repair new megnatic catcher with stainless steel plate fixed with screw at middle edge of inner shelf complete all as specified & as directed and as shown on drawing.

(n) M&L for applying French Polish to Almirah 'MU' with one or more coat till glossy finish achieved to match with existing surface (wood/woodbase) and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Sidew Board Drawing No FD-241,FD-1112

(a) Taking out old damaged/decayed leg from its position and S&F new leg in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber complete all as specified and as shown on drawing.

(b) All as per Ser No 13(a) above but stiffner of size 25 x 25mm section and –ditto-.

(c) S&F stiffner in repair to all around (long&short) at bottom/base of side board, made with 75mm x 30mm section hard wood teak incl one coat of french polish high glossy complete all as specified and directed by engr-in-charge .

(d) Taking out old damaged/decayed bottom from its position and S&F new bottom base in the same position as per existing shape and size made out of 18mm thick ply wood BWR grade with 0.9mm thick sunmica decorative choice glossy finish or as per site reqmt incl wood beading all around complete all as specified and as directed.

(e) Taking out old damaged/decayed bottom from its position and S&F new bottom base in the same position as per existing shape and size made out of 18mm thick prelaminated particle board exterior grade decorative teak face glossy finish both side and wooden beading all around complete all as specified and as shown on drawing.

(f) All as per Ser No 13(d) above but door shutter with piano type SS hinges with screw and -ditto-.

(g) All as per ser No 13(e) above but door shutter with piano type SS hinges with screw and –ditto-

(h) All as per Ser No 13(d) above but Top and -ditto-.

(j) All as per ser No 13(e) above but Top and –ditto-

(k) All as per Ser No 13(d) above but side(left/right) and –ditto-.

(l) All as per ser No 13(e) above but side(left/right) and –ditto-

(m) All as per ser No 13(e) above but Inner shelf and –ditto-

(n) Taking out old damaged / decayed drawer from its position and S&F new drawer of same size and shape complete all as specified & as directed and as shown on drawing.

(o) Taking out old damaged/decayed back ply wood from its position and S&F new plywood 6mm thick commercial BWR grade fixed in the same position as per existing shape and size including applying one coat of French polish inner and outer complete all as specified & as directed and shown drawing.

(p) Taking out old damaged / decayed handle from drawer/shutter and S&F new Square 'D' type 100 mm long (4"), steel handle as approved, the same place, complete all as specified & as directed

(q) S&F new megnatic catcher with stainless steel plate fixed with screw after taking out old unsv megnatic catcher from its position complete all as specified & as directed and as shown on drawing.

(r) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table Writing Drawing No FD-275

(a) Taking out old damaged/decayed leg from its position and S&F new leg in the same position as per existing shape and size made out of well seasoned teak wood’ timber all as specified, directed and shown on drawing.

(b) All as per ser No 14(a) above but top long rails and –ditto-

(c) All as per ser No 14(a) above but top Short rails and –ditto-

(d) All as per ser No 14(a) above but leg stiffener (long/short) and –ditto-

(e) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(f) All as per ser No 14(e) above but shutter including stainless steel long hinges and - ditto-.

(g) All as per ser No 14(e) above but bottom of cupboard and - ditto-.

(h) All as per ser No 14(e) above but cabinet sides (left/right) and - ditto-.

(j) All as per ser No 14(e) above but Inner shelf of cupboard including applying one coat of french polish and - ditto-.

(k) All as per ser No 14(e) above but back of 6mm thick plywood commercial BWR grade including one coat french polish high glossy finish and - ditto-.

(l) Taking out old damaged / decayed drawer from its position and S&F new drawer of same size and shape complete all as specified & as directed and as shown on drawing.

(m) M&L for fixing of Square 'D' type 100 mm long (4"), steel handle as approved to the same place, complete all as specified & as directed by Engr-in-charge.

(n) Taking out old damaged / decayed lock from its position and S&F new lock to the same size and shape, as approved by the ingr -in-charge, complete all as specified & as directed.

(o) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface (wood/woodbase) and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Teapoy Drawing No FD-382

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged / decayed long rail (front/rear) from its position and supply of fixing new long rail as per existing shape and size made out of well seasoned hard wood ‘Teak' complete all as directed and shown on drawing.

(c) All as per item No 15(b) here in before but for short rail (right/left) and ditto.

(d) All as per item No 15(b) here in before but for leg and ditto.

(e) All as per item No 15(b) here in before but for leg stiffener and ditto.

(f) S&F PVC shoes in repair to bottom of leg as approved quality Complete all as specified and shown on drg.

(g) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table Centre FD-235/FD-274

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged / decayed leg from its position and S&F new leg in the same position as per existing shape and size made out of well seasoned hard wood ‘Teak' completed all as specified and shown on drawing.

(c ) All as per items No 16(b) above but long rail and –ditto-.

(d) Aall as per items No 16(b) above but short rail and –ditto-.

(e) All as per items No 16(b) above but stiffener and –ditto-.

(f) S&F PVC shoes in repair to bottom of leg as approved quality Complete all as specified and shown on drg.

(g) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table Dressing Ladies with Mirror Drawing No FD-32(M)/FD-251

(a) Taking out old damaged / decayed leg from its position and S&F new leg in the same position as per existing shape and size made out well seasoned hard wood teak complete all as specified & directed and as shown on drawing.

(b) All as per item ser No 17(a) above but bottom rails (long/short) and ditto.

(c) All as per item ser No 17(a) above but mirror frame and ditto.

(d) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18mm thick plywood BWR grade with 0.9mm thick sunmica decorative natural teak glossy finish for one side and another side with applying french polish over wood filler incl wooden beading all arround complete all as specified and directed.

(e) All as per item No 17(d) here in before but side (left/right) and -detto.

(f) All as per item No 17(d) here in before but bottom and -detto- .

(g) All as per item No 17(d) here in before but inner vertical portion and -detto- .

(h) Taking out old damaged / decayed back ply from its position and S&F new 6mm thick plywood, commercial, grade BWR as per existing shape and size in the same position complete all as specified & as directed and as shown on drawing.

(j) All as per item Ser No 17(h) above but drawer bottom and ditto.

(k) Taking out old unserviceable knob from its position and S&F new knob of 25mm chromium plated knob as approved by GE/Engr-in-charge fixed to same with new brass screws/ nut / bolts and washer complete all as specified & as directed and shown on drawing.

(l) S&F in repair new sliding glass as per existing shape and size in the same position complete all as specified & as directed and as shown on drawing.

(m) Taking out old damaged / broken mirror from its position and S&F new mirror of 5mm thick as per existing shape and size complete all as specified and as directed and shown on drawing.

(n) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table Bed Side FD-276/248

(a) Taking out old damaged /decayed leg from its position and S&F new leg in the same position as per existing shape and size made out well seasoned Teak wood’ timber including applying one coat of French polish over wood filler wherever required all as specified, as directed and shown on drawing.

(b) All as per item Ser No 18(a) above but for bottom stiffener and –ditto-.

(c) Taking out old damaged decayed top from its position and S&F newTop made out of 18 mm thick plywood BWR grade with decorative choice lamination on top side and another side applying french polish incl lamination beading decorative choice in all arround complete as specified and as shown on drawing .

(d) All as per item Ser No 18(c) above but for sides (left/right) and –ditto-.

(e) All as per item Ser No 18(c) above but for shelf and –ditto-.

(f) All as per item Ser No 18(c) above but for bottom and –ditto-.

(g) Taking out old damaged decayed ply wood back form its position and S&F new 6mm thick commercial plywood grade BWR in the same position as per existing shape and size complete all as specified, directed and shown or drawing.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Bed Hard Plywood Drawing No FD-246/213

(a) Taking out old damaged / broken plywood from its position and refixing the same with new 12mm thick plywood BWR grade (Best quality as approved by GE) 07 layer to be fixed with screw as per existing shape all as specified and as directed and shown on drawing.

(b) Taking out old damaged / broken long rail from its position and S&F new long rail using well seasoned Teak wood complete all as specified and as directed and shown on drawing.

(c) All as per item Ser No 19(b) above but short rail /stiffeners and –ditto-.

(d) Taking out old damaged / broken Head board from its position and S&F new Head board using well seasoned Teak wood complete all as specified and as directed and shown on drawing.

(e) All as per item Ser No 19(d) above but foot board and –ditto-.

(f) Taking out old damaged / broken plywood from both side of Head board / foot board from its position and S&F new plywood 4mm thick teak face commercial to fixed with suitable size nails complete all as specified and as directed and shown on drawing.

(g) Taking out old damaged / broken beading from head/foot board and S&F new 12mm thick half cut teak wood beading fixed to existing place complete all as specified and as shown on drg.

(h) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface to complete existing/replaced parts after preparation of surfaces and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Book Case Drawing No FD-45(M)/FD-237

(a) Taking out old broken / decayed leg from its position and S&F new leg of the same as per existing shape and size made with Teak wood incl applying one coat french polish high gloss finish complete all as specified and as shown on drawing.

(b) All as per item Ser No 20(a) above but leg stiffner(long/short) and –ditto-

(c) Taking out old damaged/decayed top from its position and S&F new top in the same position as per existing shape and size made out of 18mm thick prelaminated particle board both side teak face including teak wood beading all around complete all as specified & directed and as shown on drawing.

(d) All as per item Ser No 20(c) but top made out of 18mm thick plywood BWR grade with 0.9mm thick sunmica with decorative choice lamination glossy finish including teak wood beading all arround and -ditto-.

(e) All as per item Ser No 20(c) but both side and –ditto-

(f) All as per item Ser No 20(d) but both side and –ditto-

(g) All as per item Ser No 20(c) but bottom and –ditto-

(h) All as per item Ser No 20(d) but bottom and –ditto-

(j) All as per item Ser No 20(c) but shelve/inner partition and –ditto-

(k) All as per item Ser No 20(c) but shutter including long poiano type hinges and –ditto-.

(l) All as per item Ser No 20(d) but shutter including long piano type hinges and –ditto-

(m) Taking out old damaged/decayed back ply wood from its position and S&F new 6mm thick plywood BWR Grade as per existing shape and size complete all as specified & as directed and shown drawing.

(n) Taking out old damaged/decayed continous Hinges piano type from its position and S&F new continous Hinges piano type fixed in the same position with screw as per existing shape and size complete all as specified & as directed and shown drawing.

(o) M&L for fixing of Square 'D' type 100 mm long (4"), SS handle as approved by GE/Engr-in-charge the same place, complete all as specified & as directed by Engr-in-charge.

(p) S&F in repair new megnatic catcher with steel plate fixed with screw to inner side of shutter for holding the shutter complete all as specified & as directed by Engr-in-charge.

(q) M&L for applying French Polish to wood/wooden base surface with one or more coat till glossy finish achieved to match with existing surface and remove the all dirt/dust etc from existing/ replaced parts before polish and applying wood filler whenever required complete all as specified, directed and shown on drawing.

Table 900*600*760mm wooden W/O drawer Drawing No FD-223/FD-231/FD-284

(a) Taking out old damaged / decayed top from its position and S&F new top as per existing shape and size in the same position made out of 18 mm thick plywood BWR grade with one side 0.9mm thick sunmica decorative natural teak glossy finish on top and another side applying french polish over wood filler including wooden beading all aroung complete all as specified and directed and shown on drawing.

(b) Taking out old damaged/decayed long rail from its position and S & F new long rail in the same position as per existing shape and size made out of well seasoned hard wood Teak including applying one coat of French polish over wood filler complete as directed and shown on drg.

(c) All as per item Ser No 21(b) above but short rail and –ditto-.

(d) All as per item Ser No 21(b) above but leg and –ditto-.

(e) All as per item Ser No 21(b) above but stiffener (long/short) and –ditto-.

(f) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Bin solid linen small/large Drawing No FD-244

(a) Taking out old damaged / decayed leg from its position and S&F new leg in the same position made out of well seasoned ‘teakwood’ timber complete all specified and as directed and as shown on drawing.

(b) -Ditto- all as per item Ser No 22(a) above but for bottom/top rail and –ditto-.

(c) -Ditto- all as per item No 22(a) above but stiffener/batten/brackets –ditto-

(d) -Ditto- all as per item No 22(a) above but stopper (25 x 25 x 150mm) –ditto-

(e) Taking out old damaged / decayed top ply from its position and S&F new top ply 6mm thick with Teak veneer finish on outer surface as per existing shape and size in the same position including 3mm x 25mm TW ebging all around complete all as specified and directed and shown on drawing.

(f) -Ditto- all as per item Ser No 22(e) above but for front side plywood and –ditto-.

(g) -Ditto- all as per item Ser No 22(e) above but for back side commercial plywood and –ditto-.

(h) Taking out old damaged / decayed plastic cane from both side and S&F new aluminium wire mess with ss coating 1mm thick as approved by Engr-in-Charge in the same position including TW beading all around complete all specified and as directed and as shown on drawing.

(j) M&L for applying French Polish one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

Rifle rack for 36 rifle INSAS/LMG Drawing No GE/BIN/TD/18/2018

(a) Taking out old damaged/decayed Bottom of Rack Rif (Left/Right) from its position and S & F new Bottom of Rack Rifle including notch to suit for stay of rifle in the same position as per existing shape and size made out of well seasoned hard wood in one pcs as approved by Engr -in-Charge including applying one coat of wood primer over wood filler complete as directed and shown on drg.

(b) All as per item Ser No 23(a) above but for bottom Base of Rack Rif and –ditto-.

(c) All as per item Ser No 23(a) above but for Up Right (100 x 100 x 905mm )of Rack Rif and –ditto-.

(d) All as per item Ser No 23(a) above but for Top (110mm x 40mm section ) of Rack Rif and –ditto-.

(e) All as per item Ser No 23(a) above but for Bracket (90 x 90 x 75mm) of Rack Rif and –ditto-.

(f) Taking out old damaged / broken Flat Iron from its position and S&F new Flat Iron of 25mm x 3mm thick as per existing sahape and size to the same place with 10mm dia bolt, Nut and washer complete all as specified and as shown on drg.

(g) M&L for applying Synthetic Enamel paint one or more coat till glossy finish achieved to match with existing surface after preparation of surfaces with applying wood filler wherever required complete all as specified & as directed and as shown on drawing.

BBKundu (BID ID -3485181)

HINDUSTAN ENGINEERING WORKS (BID ID -3479798)