Repair to plastering, plumbing, external painting and misc B/R items in OMQs and OTM accn under AGE B/R-II at GE (AF) No. 2 Jodhpur

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each or as directed by Engineer-in-Charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4 sqm each as directed by Engineer-in-Charge

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site to store complete as directed by Engineer-in-Charge.

Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site to store complete.

Dismantling of cast iron or reinforced concrete drain pipe, jointed in cemented mortar and taking out of trenches or in vertical position of internal dia 100 mm & less all as directed by the Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

Demolition of cement concrete (reinforced) in any position not otherwise specifically provided for and removing from site all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises as directed by Engineer-in-Charge

Taking down cement or cement lime plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc and complete all as specified

M&L for preparation of old plastered or unplastered surfaces of walls and applying one coat of white wash as directed by Engineer-in-Charge

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash as directed by Engineer-in-Charge

M&L for Complete removal of old existing surfaces and two layer of wall care putty for smooth surface of wall complete all as specified & directed.

M&L for preparation of old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying two coat of oil emulsion distemper white or approved tinted including removing existing nails, if any and filling the disturbed / surface, holes/voids with wall care putty/POP to achieve the smooth surface complete all as specified & directed.

M&L for preparation of plastered and unplastered surface of walls and applying two coats of wheather proof exterior emulsion paint complete all as specified and all as directed

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint as directed by Engineer-in-Charge

M&L for preparation of old painted wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint as directed by Engineer-in-Charge

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surfaces finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:6 on stone masonry surfaces finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M&L rendering 10mm thick in CM (1:3) on stone masonry fair faces of concrete surfaces as in ceilling finished fair and even without using extra cement complete all as specified and as directed

M&L for preparation of new plastered and unplastered surface of walls and applying two coats of wheather proof exterior emulsion paint complete all as specified and all as directed

M&L for two coats of oil emulsion distemper , white or tinted, over a coat of chalk whiting smooth putty surfaces of walls all as directed.

M&L for preparation of New plastered or unplastered surfaces of ceiling and applying two coat of white wash.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described priming with red oxide and applying two coats of synthetic enamel paint as directed by Engineer-in-Charge

M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described priming coat with pink primer and applying two coats of synthetic enamel paint as directed by Engineer-in-Charge

S&F steel windows with side hung shutters including projecting type hinges sith steel handle and steel peg stay , complete with glazing bars, dovetailed or welded. (Note : One AC vent of size 0.70 mtr x 0.50 mtr with top hung shutter will be provided)

All as per item No 25.00 above but without glazing bars complete all as specified and directed.

M&L powder coated anodised aluminium frame for doors, windows, louver type ventilators including rotating type fixing arrangement for fixing of louver glass joining cleat for fixing etc complete and all as specified.

S&F powder coated louvers with including arrangement of fixing glass pinhead as per size & louvers ventilator (Glass shall be measurement separately) complete all as specified and as diredcted.

S&F 30 mm thick factory made , second class hard wood flush shutters ,solid core constructions with block board core and plywood face panels, commercial type on both face directed by Engineer-in-Charge

S&F 35 mm thick factory made , second class hard wood and skeleton shutters open rebated and prepared to receive glass gauze etc (without sash bars ) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24 (a) supplied and fitted to chowkats as directed by Engineer-in-Charge

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, as directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site as per specification & drawing as directed by Engineer-in-Charge

S&F 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge

S&F 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or casr aluminium alloy as directed by Engineer-in-Charge

S&F for 100 mm long butt hinges, medium weight stainless steel as directed by Engineer-in-Charge

S&F aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples as directed by Engineer-in-Charge

S&F 300 mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete as directed by Engineer-in-Charge.

S&F floor door stopper, with 150 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor as directed by Engineer-in-Charge.

Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm and n exc 2 sqm each as directed by Engineer-in-Charge

S&F in repairs aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge.

S&F in repairs 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast aluminium alloy

S&F in repairs 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge.

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

S&F in repair galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples as directed by Engineer-in-Charge

S&F in repairs stainless steel curatin rod , having outer dia 25 mm including stainless steel fixing brackets all as directed by Engineer-in-Charge.

S&F in repairs Stainless Steel cap for curtain rod for 25mm dia curtain rod as directed by Engineer-in-Charge.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones as directed by Engineer-in-Charge.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F in repair CP tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and all as specified and directed by Engineer-in-Charge

S&F in repair CP grating 100 mm dia all as specified and as directed.

S&F in repair glass corner shelf (set of three) fixed with and including chromium plated brass screws and wooden/plastic cleats and all as specified and as directed.

S&F in repairs stainless steel plate rack 0.56mm thick of standard pattern of size 750x600x250 mm complete as directed by Engineer-in-Charge

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm complete all as specified and directed by Engr-in-Charge.

S&F ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed as directed by Engineer-in-Charge

S&F 40 mm dia cupboard knobs of fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by Engr-in-Charge.

S&F cupboard shutters of required sizes at site made out of 18mm thick WPC laminated board with decorative teak face density not less than 650 Kg/cum all the edges shall be covered with 2 mm thick edge beading tape or 90 degree edge bend finish as per make and specification & the panels shall be fabricated using adhesive and screws where required complete all as specified. Make :- Rajshree or equivalent.

S&F 18mm thick WPC plain board of required size in cupboards and similar works density not less than 650 Kg/cum all the edges shall be covered with 2 mm thick edge beading tape or 90 degree edge bend finish as per make and specification & the panels shall be fabricated using adhesive and screws where required complete all as specified. Make :- Rajshree or equivalent.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as directed by Engineer-in-Charge.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup , screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge.

S&F 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge.

S&F in repairs 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends for iron pipes as directed by Engineer-in-Charge

S&F in repair brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union as directed by Engineer-in-Charge.

S&F in repairs brass chromium plated health faucet of 15 mm bore complete as directed by Engineer-in-Charge.

S&F in repairs brass chromium plated center hole basin mixer without popup waste system, all as directed by Engr-in-charge

S&F in repairs brass chromium plated sink mixer with regular spout w/m, all as directed by Engr-in-charge

S&F in repairs brass chromium plated wall mixer with bend (Provision for O H Shower) all as directed by Engr-in-charge

S&F in repairs PVC connection 15 mm size with nuts of length 450 mm as directed by Engineer-in-Charge.

S&F in repairs stainless steel toilet paper holder fixed to walls with chromium plated (CP) brass screws all as directed by Engr-in-charge

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe PVC connection 15 mm size with nuts of length 450 mm.complete all as specified and as directed by Engineer-in-Charge

S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and as directed by Engineer-in-Charge

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including PVC 'P' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish and as directed by Engineer-in-Charge.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets all as directed by Engr-in-charge.

S&F in repairs single mirror bath room cabinet moulded body and framed (made from strong and fine quality ABS plastic ) with hinged door of size 16 " x 12 " x 6 " white or ivory colour fixed on wall with appropriate rawl plugs . Make : Prayag/Polytuff as directed by Engineer-in-Charge

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long all as directed by Engr-in-charge

S&F in repair sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of suitable length, all as directed by Engr-in-charge

S&F in repair sink made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of suitable length, all as directed by Engr-in-charge

Dismantling of existing water tank (PVC/RCC/AC) exc 500 ltr but n exc 1000 ltr capcity and removing from site complete as directed by Engr -in-charge.

Dismantling of existing water tank (PVC/RCC/AC) exc 250 ltr but n exc 500 ltr capcity and removing from site complete as directed by Engr -in-charge.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed as directed by Engineer-in-Charge

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixedas directed by Engineer-in-Charge

Supply and laying 15mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls (concealed type) and ceilings or laid in floors all as specified and directed.

Supply and laying 20 mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

S&F PVC (SWR) gully traps of size 125/110 mm,setting and jointing with solvent cement and complete and as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints fixed in walls as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints but fixed in walls as directed by Engineer-in-Charge

S&F in repair for PVC (SWR), junction single, (Single T) with door 110 mm dia equal or unequal as directed by Engineer-in-Charge

All as per item No.90.00 ,but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) door bends 110 mm dia as directed by Engineer-in-Charge

All as per item No.92,but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) Cowl 110 mm dia as directed by Engineer-in-Charge

S&F in repair for PVC (SWR), 75mm dia of floor trap, with grating including jointing with solvent cement and complete and as directed by Engineer-in-Charge.

Dismantling of existing treatment of roof surface and Wire brushing , cleaning top surfaces of tarrace or cement concrete including flashing and junction of parapets complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete B-1. 1:2:4 (20mm graded aggregate) in padding finishing surface of concrete topping even and fair without using extra cement all as specified of average thickness 50 mm in slop 1:40 over roof & complete all as specified and directed by Engr-in-Charge.

Wire brushing and cleaning top surfaces of tarrace or cement concrete including dismantling existing old roof treatment and junction of parapets as directed by Engineer-in-Charge

M&L10 mm thick screed bed with CM 1:4 with water proofing compound @ 3% by weight of cement finish even and smooth surfaces using without extra cement. Water proofing compound shall be measured and paid seperately as directed by Engineer-in-Charge

M/L for providing APP based polymeric membrane minium weighting 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non wave fabric ( weight not less than 150 gms/sqm ) land over a coat of primed surfaced by forced application and complete all as specified and as directed by Engr-In-Charge.( Note : Quoted rate shall be deemed to be included for work in building/structure of any height) overlapped by 100 mm in all sides & including 250 gms per sqm bituminus primer as directed by Engr-in-Charge

Supply only integral water proofing compound ISI marked as directed by Engineer-in-Charge

M&L for water proofing treatment of sunken floor of WCs bathroom etc by applying of the following specifiaction:-(i) Cleaning of sunken floor surface with mechanical means i.e wire brush/air blower etc and remove all loose/unsound material dirt dust etc. (ii)Applying cement slurry mixed with acrylic based polymer modified cementious composite compund coating Hydroproof Xtra of FOSROC /Equivalent of Dr Fixit of Pidilite industries Ltd in the ratio 1:2:4 (one part of acrylic polymer : two part of water and four partof cement) (iiii) First layer of cement slurry @0.444 kg /sqm mixed with acrylic based modified cementious composite compund @0.222 litre/sqm and allow it to air dry for 4 hour. (iv) Second layer of cement slurry @0.222 kg /sqm mixed with acrylic based dified cementious composite compound @0.111 litre/sqm and allow it to air dry for 4 hour followed with water curing for 48 hours (v) 200 micron thick polytgen film shall be pasted with help of adhesive over treatment . Note:- Joints of WC/Trap/Soil waste shall be prperly sealed with sealing compund . Testing of all traps and joints and sunken slab shall be done as per IS-1742 before filling and tiling work as directed by Engineer-in-Charge.

M&L for plain cement conrete 1:5:10 type E-2 (using 20 mm graded broken bricks aggregate ) as in foundation and mass concrete complet all as specified and as directed by Engineer-in-Charge

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors as directed by Engineer-in-Charge.

Supply and laying 32 mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge

M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone or brick masonry surfaces as directed by Engineer-in-Charge.

M&L for light coloured vitrfifed cermaic tiles 10 mm thick area of each tiles not less than 0.36 sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1;6 as directed by Engineer-in-Charge

All as per item no. 109.00 above but on vertical surfaces such as dados skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick renedering in CM 1:4 on stone masonary surfacesas directed by Engineer-in-Charge

M&L for PCC block masonary with solid blocks exc 10 cm in width 1:3:6 Type C1 20 mm graded aggregate and setting in cement moratr 1:6 complete and as directed by Engineer-in-Charge

M&L for granite (of any type ) tiles 20 mm thick machine cut in skirting /dado over and including 10 mm thick rendering in CM 1:4 on stone masonry surfaces jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed by Engineer-in-Charge

Cutting holes in brick walls in cement mortar for insering holdfasts and making good dismantled portion in cment mortar 1:3 or cment conrete 1:2:4 type B-1 as required exc half brick but not exc one brick as directed by Engineer-in-Charge

M&L for framed work as in door or gates of angle or other section with gusset plate rails braces etc complet drilled for fixing of steel sheeting or other covering . Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings 9 exclusive of steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing complete grade Fe-290 (Gde E-165) as directed by Engineer-in-Charge

S&F framed work such as grills gratings etc with ends of bars shoulders and/or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings frame work of water tanks and similar works conforming to Fe 290 gde E-165.

M&L for PVC green sheet 1.00 mm in wall cladding steel gate and similar work cut to size holes punched includinground headed screws clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted seams including bending or turning up mitred angles etc as required complete all as required as directed by Engineer-in-Charge

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer as directed by Engineer-in-Charge.

S&F figured glass pin head type 4 mm thick, fixed as louvers in ventilators supplied square n.exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc for 125 X60 mm complete & fixing also as specified supplied and fixed and as directed by Engineer-in-Charge

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc for 105 X60 mm complete & fixing also as specified supplied and fixed and as directed by Engineer-in-Charge

Demoliton of reinforced cement concrete of any description for roofs, floor (Other than ground floor), beams, staicases, landing, chajjas and similar work and complete all as specified

M&L RCC Nominal mix Type B 1, 1:2:4 (20 mm graded aggregate) for slabs supported on walls, beams and colimns in floor, roofs, landings, balconies, deck slab and in shelves and the like and complete all as specified.

S&F MS TMT bars 10mm dia and over, cut to length, bent shape required, including cranking, bending, hooking etc and binding with MS wire 0.9mm dia(annealed as directed by Engineer-in-Charge.

S&F MS TMT bars 5mm dia and over upto 10mm dia in stirrups, spacers and binders and complete all as specified.

M&L for Formwork to soffits of suspended slabs for rough finished surfaces of concrete such as roof slabs, floor slabs, landing and similar work: not exc 200 mm thick (horizental or sloping) and complete all as specified .

M&L for Formwork to edges of concrete flats, treads, breaks in floors, concrete railings, opening in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC /PCC bands in walls, horizental or sloping and similar work exc 10 cm but n.exc 20 cm wide for rough finished and complete all as specified.

M&L upto 6 m height from ground including neccessary suttering and form work for applying 10mm thick bonding coat of modified styrene butadiene emulsion (SBR bonding agent i.e. Nitobond SBR 45) in proportion 1 (Nitobond SBR 45) : 1(water) : 3 (OPC) by volume with the brushes etc to bind new cement plaster/ polymer modified plaster/ concrete/ screed concrete with old surface including removal of loose / disintegrated old concrete / plaster surface preparaion etc and applying RCC (1:1.5:3) OR 15 mm thick plaster with polymer modified mortar fortified with SBR (Nitobond SBR 45 ) in proportion 1:3 by weight 5 litres Nit bond SBR 45 to added to 50 KG Cement with 13 litre water addition, finished surface to match with existing surface of ceiling, beams, chajja and alike complete all as specified & directed.

Bansal Enterprises (BID ID -3083952)

JAMWAY MATA CONSTRUCTION COMPANY (BID ID -3086404)

VIKAS CONSTRUCTION CO. (BID ID -3090354)

GANGADHAN ENTERPRISES (BID ID -3085332)