Repair renovation DSC posts located on perimeter of OFD

Amount

CIVIL WORKS

Demolition cement concrete surfaces in ground floors and pavings n exc 15 cm thickness (below or above ground level).

Demolition of cement concrete of any description and in any position not otherwise specifically provided for

Taking down chaukhat or frame with shutters (without taking off shutters from the frames) n exc. 1.5 sqm.

Taking down Shutters of any description exc 1 sq. m but n exc. 2 sqm each

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

Ditto as item No 1.05 but without glazing bar

Repairing of existing steel windows by providing handles, locking /closing arrangements including supply of required fittings.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work. M&L

Plain fillets. Exc. 13 sq.cm but nexc. 25 sqcm square,rectangular or triangular in section, clean sawn, secured with nails or brads.M&L

Plain fillets. Exc. 6 sq.cm but nexc. 13 sqcm square,rectangular or triangular in section, clean sawn, secured with nails or brads.M&L

S&F Plywood, grade BWR,type BB, fixed with screws to timber frame Work.

S&F Sheet glass,3 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane for ventilator.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

S&F 100 mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed

Preparation of new surface / old treated surface and applying two coat synthetic enamel paint (ordinary tint) over one coat of red oxide / primer over steel surfaces.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F 25 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S & F 100 mm Butt hinges, medium , cold rolled mild steel, and fixed

S& F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed.

S& F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed

S&F 150 mm Aluminium handles, cast type, anodised.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

All as per item no1.18 above but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces with smooth finish without using extra cement.

S&F Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

S&F Glazed ceramic Coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm / mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tiles.

S&F Virified Ceramic tiles 10 mm thick ( light shade) (square/rectangular)polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes

M & L 75 mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate)

M&L 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) with smooth finish without using extra cement.

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surface ( including primer) by forced application complete all as specified.

Finishing of concrete surfaces with smooth finish without using extra cement.

Reinforced cement concrete Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like Type B0 1:2:4 (12.5 mm graded aggregate)

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips TMT bar.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat fair finished surface.

S& F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe ) complete including provision of lime concrete bedding & flush pipe to PVC (SWR) 'P’ trap. Make: Parryware/ Hindware/ Kerovit

S&F, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 10 liter capacity , flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern. complete with PVC connections 15mm size with PTMT nuts of length 450mm except angle cock, Make: Parryware/ Hindware/ Kerovit

S&F 110mm PVC (SWR) WC connector with lip ring

S&F, PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , Bore in 110mm.

S&F, PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , Bore in 75mm.

S & F 110mm PVC (SWR) bend any radius provided with access door

S & F 110mm PVC (SWR) bend any radius /floor trap/nahani trap including Jali Chromium plated

S & F PVC (SWR) vent cowl 75mm

S&F 150 mm dia Bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F 15 mm dia fancy type cromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S& F Tubes, medium grade' galvanised, 15 mm dia with all fitting and fixed complete to walls and ceilings or laid in floors

Preparing old surfaces plastered or unplastered and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work/old (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Make:- Water proof paint Apex (Ultima) Asian/ Dulux weathermax/ Nerolac

Preparing old surfaces plastered or unplastered and applying two coat of oil emulsion on walls make: Asian ( Tractor emulsion) / Nerolac/ ICI Dulux.

Preparation of new surface / old treated surface and applying two coat synthetic enamel paint (ordinary tint) over one coat of red oxide over steel surfaces.

Preparation of new surface / old treated surface and applying two coat synthetic enamel paint (ordinary tint) over one coat of primer over wooden surfaces.

Cutting holes in brick walls in built in cement mortar or stone walls n exc half brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required

Removing building materials etc. to a distance up to 500 metres or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.

S&F Glass dividing strips, 3 mm thick and 28 mm wide set in floor joints.

Credit (-) old/unserviceable dismentled wooden doors /shutters with or without frames except grills / welded mesh jali etc.

EARMARK INFRATECH INDIA PVT. LTD. (BID ID -748526)

M/S RP AGRAWAL (BID ID -753938)