REPAIR MAINT OF PUMP SET MOTORS STARTER INCLUDING PANEL BOARDS AND MISC WORKS AT WATER SUPPLY AT WATER SUPPLY INSTALLATION AT SOUTH OF RAILWAY LINE UNDER GE MISSAMARI

Amount

Servicing/Overhauling of 3 Phase 415 Volts 1440 RPM 75 HP capacity Induction Motor (MAKE : KIRLOSKAR/ JYOTI) installed at Old Pump House alongwith following others repairs :- (a) Taking out Motor from its Position by decoupling from Pump and disconnecting all Cable Connections. (b) Dismantling of induction Motor complete Part by Part carefully, testing all Coils, degreasing bearing and display all the Parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the Serviceability of existing Parts. (c) Heating & Varnishing to Stator with super quality varnish and dried out properely with external heat as ordered and as directed. (d) Reassembeling the Motor complete with all existing Serviceable Parts obtained , greasing the Bearing with bearing grease and new Parts as ordered by Engineer-in-Charge (New Parts shall be measured and paid separately under relevant Item here-in after) (e) Reinstall the Motor at its existing Position, couple with the Pump connecting all Cable connections and testing on completion complete all as specified and as directed. Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). .Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No-1 to 5 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only DE ( Driver End ) Bearing No- NU314/N 344 or as per existing size suitable for 75 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Supply only NDE ( Non Driver End ) Bearing No- 6313/6331 or as per existing suitable for 75 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Supply only Bakelite connection terminal plate with brass nuts bolts and washers suitable for 75 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed.

Rewinding burnt coils of Induction Motor stator of capacity 75 HP obtained from Item Ser No-1 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed.

Servicing / Overhauling of Electric driven Multi driven Pump-set having discharge 40000 GPH, H 61-M ( Make- BE, ALSTOM ) coupled with induction Motor 75 HP capacity installed at Old Pump house along with following others repairs :- a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b). Dismantling of Pump complete part by part carefully, degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope. d). Reassembeling the Pump complete with all existing serviceable parts obtained, greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position, couple with the Motor and connecting all suction delivery water connections and testing on completion complete all as specified and as directed. Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No-7 to 14 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only DE ( Driver End ) bearing as per existing size (heavy duty) for pump coupled with 75 HP motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) bearing as per existing size ( heavy duty) for pump coupled with 75 HP motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only SS Pump Shaft sleeve for Pump shaft of 75 HP Motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only CI Impeller as per Existing of pump set for pump coupled with 75 HP motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only Pump Shaft for pump coupled with 75 HP motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only Rubber Tyre Coupling complete set UNIQUE -PX-90 for pump coupled with 75 HP motor to incorporate against Item No-6 here-in-above complete all as specified and as directed.

Supply only CI coupling tyre only UNIQUE PX-90 for pump coupled with 75 HP motor to incorporate against Item No-06 here-in-above complete all as specified and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 6 here-in-before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / overhauling of 3 Phase 415 Volts 1440 RPM 50 HP capacity induction (Motor Make- Kirloskar, Alstom ) Installed at Old Pump House, along with following others repairs :- a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully, testing all coils, degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed. d). Reassembeling the motor complete with all existing serviceable parts obtained , greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge. (New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion complete all as specified and as directed. Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 16 to 19 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only DE ( Driver End ) Bearing No- 6407 ZZ or as per existing of Induction Motor against Item No-15 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) Bearing No - 6408 ZZ or as per existing size of Induction Motor against Item No-15 here-in-above complete all as specified and as directed.

Supply only Bakelite connection plate with brass nuts bolts and washers of Induction Motor against Item No-15 here-in-above complete all as specified and as directed.

Rewinding burnt coils of Induction Motor stator of capacity 50 HP obtained from Item Ser No-15 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed.

Servicing/over hauling of Electric driven Multi Staging Pump set of Discharge cap 2040 LPM, H-55 M (Pump Make-Beacon) Installed at Old pump House coupled with induction Motor 50 HP capacity along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantling of Pump complete part by part carefully, degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained , greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position, couple with the Motor and connecting all suction delivery water connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 21 to 23 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only DE ( Driver End ) bearing as per existing size (heavy duty) for pump coupled with 50 HP motor to incorporate against Item No-20 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) bearing as per existing size ( heavy duty) for pump coupled with 50 HP motor to incorporate against Item No-20 here-in-above complete all as specified and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 20 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / over hauling of Electric Motor Vertical 3 Phase 415 Volts 1440 RPM capacity 20 HP ( Make- Kriloskar) . installed at Jalkendra, along with following others repairs. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully, testing all coils, degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c) Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained , greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 25 to 31 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only DE ( Driver End ) bearing as per existing size (heavy duty) for pump coupled with 20 HP motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only NDE ( Non Driver End ) bearing as per existing size ( heavy duty) for pump coupled with 20 HP motor to incorporate against Item No-24 here-in-above complete all as specified and as directed.

Supply only Bakelite connection plate with brass nuts bolts and washers of Induction Motor against Item No-24 here-in-above complete all as specified and as directed.

Rewinding burnt coils of Vertical Electric Induction Motor stator cap 40 HP obtained from Item Ser No-24 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Supply only Plastic Rotar Fan of Motor against Item No-24 here-in-above complete all as specified and as directed.

Supply only 20 HP Motor to incorporate against each Item No-24 here-in-above Tyre coupling Rubber tyre only complete set No-60/70 complete all as specified and as directed.

Servicing/over hauling of Electric driven Horizontal split casing Pump set of Discharge cap 1230 LPM, H-30 M (Pump Make-Kirloskar , HBB) Installed at Old pump House, New Jalkendra coupled with induction Motor 20 HP capacity along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantling of Pump complete part by part carefully , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained , greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position, couple with the Motor and connecting all suction delivery water connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 32 to 37 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-31 here-in-above DE ( Driver End ) bearing as per existing size complete all as specified and as directed.

Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-31 here-in-above NDE ( Non Driver End ) bearing as per existing size complete all as specified and as directed.

Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-31 here-in-above SS Pump Shaft sleeve for Pump shaft complete all as specified and as directed.

Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-31 here-in-above CI Impeller as per Existing complete all as specified and as directed.

Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-31 here-in-above Pump Shaft complete all as specified and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 31 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 10 HP Motor (Make-Kirloskar, Jyoti , CG ) Installed at Old pump House, along with following others repairs. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c)., Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained, greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 39 to 42 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only 10 HP Motor to incorporate against each Item No-38 here-in-above DE ( Driver End ) bearing as per existing size complete all as specified and as directed.

Supply only 10 HP Motor to incorporate against each Item No-38 here-in-above NDE ( Non Driver End ) Bearing as per existing size complete all as specified and as directed.

Supply only 10 HP Motor to incorporate against each Item No-38 here-in-above Bakelite connection plate with brass nuts bolts and washers complete all as specified and as directed.

Rewinding burnt coils of Induction Motor stator cap 10 HP obtained from Item Ser No-38 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed

Servicing / over hauling of Electric driven Horizontal split casing Pump set of Pump Discharge Centrifugal 10000 - GPH, H- 40M, 10 HP, (Pump Make-Kirloskar ,BE, Jyoti ) Installed at Old pump House along with following others repairs. a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery water connections , setting aside Pump from base plate , b).Dismantling of Pump complete part by part carefully, degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Replacement of Gasket set and gland packing rope . d). Reassembeling the Pump complete with all existing serviceable parts obtained, greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after) e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery water connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 44 to 52 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above DE ( Driver End ) bearing as per existing size complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above NDE ( Non Driver End ) bearing as per existing size complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above SS Pump Shaft sleeve for Pump shaft complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above CI Impeller as per Existing complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above Pump Shaft complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above tyre Coupling complete set No.60 complete all as specified and as directed.

Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above tyre copling rubber only N0.60 complete all as specified and as directed.

Welding Turning and machining works of Pump Shaft obtained from Item No 43 here-in-Before to true size to match with the new Parts / existing serviceable parts for proper allignment and smooth operation of Motor Pump Set complete all as specified and as directed

Supply only Tyre coupling rubber Pump coupled with 10 HP Motor to incorporate against each Item No-43 here-in-above complete all as specified and as directed.

Servicing/over hauling of 1 Phase 240 Volts 1440 RPM 1/1.5 HP Installed at various pump house along with following others repairs. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearing and display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts. c). Heating & varnishing to stator with super quality varnish and dried out properely with external heat as ordered & directed d). Reassembeling the motor complete with all existing serviceable parts obtained , greasing the bearing with bearing grease , and new parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Item here-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as ''Supply only'' (s) of this schedule. However labour element involved in replacement is included in unit rate quoated against this Item. (ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 55 to 58 but required to complete the repair work / smooth functioning of Motor shall be deemed to be included with the unit rate .Transportation of Stator / Rotor parts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate. iii). Rewinding of stator / rotor of motor, any machine work where involved shall be measured and paid separetely against relevant item of this schedule.

Rewinding burnt coils of Induction Motor stator cap 1/1.5 HP obtained from Item Ser No-53 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve the required /specified RPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete as directed.

Supply only Differential pressure switch for booster pump of capacity 1/1.5 HP as per existing size complete all as specified and as directed.

Supply only Level float valve for booster pump of capacity 1/1.5 HP as per existing size complete all as specified and as directed.

Supply only Brass foot valve for booster pump of capacity 1/1.5 HP as per existing size complete all as specified and as directed.

S&F LED aviation abstruction light double headed 100 Watt with and including fixing arrangement using 50mm bore GI pipe (medium weight) 2 mtrs height complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 10 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Material and labour for PVC insulated and sheathed flat 3 core, Size 16 Sqmm copper stranded conductor water proof submersible cable 1100 Volts Grade , and connecting to submersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed.

Supply, laying , fixing , passing through pipe or cable tray PVC insulated & PVC sheathed unarmoured Multi core copper conductor 1 core 50 Sqmm 1100 Volts Grade cable confirming to IS 694 including including taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed.

S&F in repair Cast Iron Foot valve of size 100 mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position complete all as specified and as directed

S&F in repair Cast Iron Foot valve of size 150mm to suction Pipe of Motor Pump set by disconnecting Lifting suction Pipe from shallow well/ UG Sump and fixing in Position complete all as specified and as directed

S&F in repair Cast Iron NRV of size 100 mm with gun metal seat PN 1.6 to delivery Pipe of Motor Pump set fixing in Position complete all as specified and as directed

S&F in repair Cast Iron NRV of size 150 mm with gun metal seat PN 1.6 to delivery Pipe of Motor Pump set fixing in Position valve complete all as specified and as directed

S&F in repair Cast Iron Diaphragm Valve of size 150 mm wheel type with necessary Nut, Bolts, Gasket, Washer, etc. complete all as specified and as directed.

Repair to water level indicator of OH Reservoir by replacement of brass float ball 300 mm dia 2mm thick mild steel pulley flexible steel wire rope from brass float ball to measuring key and painting to indicator with 2 coat of synthetic enamel paint and marking number, strip for measuring of water level at OHT with red/black/Yellow reflective type colour complete and all as directed.

Desliting/Taking out accumulated Silt, Sand , Mud etc.,from Jack well of diameter 6.10 Metre and 12.20 Metre deep ( installed at old pump house) through Manhole, removing the same to a distance not exc. 50 Metre, complete all as specified and as directed. Note : The contractor to monitor day to day and avoid damage of VT pumpset due to intake of sand/mud (accumulated into bowl assembly Note:- Any damage made to Jack well, the contractor is fully responsible for repair the same without any extra payment.

M&L cutting/Cleaning amd removing of all unwanted vegetations, bushes, grasses, roots ,etc and removing to a distance not exc 50mtrs complete all as specified and as directed.

M&L preparation of old steel surfaces of valve pit chamber cover with angle iron frame of size 900mm x 900mm and applying one coat of super enameled black paint complete all as specified and as directed

M&L preparation to surfaces of sluice/release/NRV Valves of size 300/250 mm dia and applying one coat of super enameled black paint complete all as specified and as directed

Supply only grease for lubrication of bearings AP 3 moving parts of motors/pumpsets/chain pulleys etc complete all as specified and as directed

Supply only Copper lugs of size 6 to 25 sqmm for connection of starters Copper cables at various water supply installations complete all as specified and directed.

Supply only Copper lugs of size 25 to 50 sqmm for connection of starters Copper cables at various water supply installations complete all as specified and directed.

Supply only aluminium lugs of size 70 to 95 sqmm for connection of starters at various water supply installations complete all as specified and directed by EIC.

Supply only aluminium lugs of size 120 to 185 sqmm for connection of starters at various water supply installations complete all as specified and directed by EIC.

Supply only aluminium lugs of size 240 to 300 sqmm for connection of starters at various water supply installations complete all as specified and directed by EIC.

Supply, Installation, commissioning and Testing Chlorine Pressure Feed Pump high pressure single head gear motorised adjustable Dozing pump with acessories including Lead Tubing, Connection Nuts, Injection Check Valves, Clay Weight, FRP Dosing tank and Ferrules including taking out/removal of old unserviceable one complete all as directed.

Supply & laying Steel Water Tubing 80mm bore, Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other situation including Taking up or down old unserviceable Pipe, complete as all specified and as directed.

Supply & laying Steel Water Tubing 100mm bore, Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other situation including Taking up or down old unserviceable Pipe, complete as all specified and as directed.

Supply & laying Steel Water Tubing 150mm bore, Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other situation including Taking up or down old unserviceable Pipe, complete as all specified and as directed.

M&L Cast Iron Sluice Valve 80 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve, complete all as specified and as directed.

M&L Cast Iron Sluice Valve 100 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve, complete all as specified and as directed.

M&L Cast Iron Sluice Valve 150 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve, complete all as specified and as directed.

M&L Cast Iron Sluice Valve 250 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve, complete all as specified and as directed.

M&L Cast Iron Sluice Valve 300 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve, complete all as specified and as directed.

Supply and fabrication from MS Sheet/Sections, frame of motor pump set of 75/70 HP as per existing shape & size and applying a coat of red oxide zinc chrome primer including dismantling/taking out old unserviceable one complete all as specified and as directed.

Supply only Brass bar/lock for making of brass bushing as per as per existing housing of various pump sets, induction motor and submerssible pump complete all as specified and as directed.

Supply and fixing Rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 (Gde E-165) and applying a coat of red oxide zinc chrome primer including dismantling/taking out old unserviceable one complete all as specified and as directed.

Supply and fix in repair, Single Phase Preventer 415 Volts, 50 Hz complete all as specified and as directed

Supply of JCB/Fork land for removal of Silt/Gravels in the open drain from Ghabharu River to sand catcher at Jalkendra all as specified and directed by EIC Note:- (a) Rate quoted is deemed to inclusive of payment of Driver, Feul, Coolent, Lubricant or any other acessories as required (b) No additional charges will be paid for the T&P required. (c) Work shall be carried out only in written orders of Engg-In-Charge, and duty roster mentioning the Vechile Registration No. shall be maintained for start time and end time, date wise signed by JE, Engg-In-Charge,Contractor dully countersigned by GE. Photographic evidence shall be submitted to Engg-In-Charge as demanded and cost of Photos (One Photo per hour) is deemed to be inclusive in the unit rate quoted.

M&L for Cement Concrete 1:2:4 type B2 (40mm graded coarse aggregate) as in Foundation for 150 HP IRP pump motor, Filling, Mass Concrete and using 10 mm TMT bar having centre distance between bars not more than 100 mm etc including demoliation of old unserviceable foundation, complete all as specified and as directed.

Excavation in trenches as in Soft/ Loose Soil not exc. 1.50 Metre wide and not exc 1.50 Metre in depth and getting out for taking out/laying of GI/CI Pipe Line and making bottom surfaces of excavation leveled and required gradient complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 25 Cm in Soft/Loose Soil, complete all as specified and as directed.

Removing Surplus soil/spoil to a distance not exc. 50 Metre away and depositing where directed at a level not exc. 1.50 Metre above the starting point complete all as specified and as directed.

Taking up or down GI steel tubing of 25/32mm bore including connections from trenches/walls/floors etc complete all as specified and as directed.

Taking up or down GI steel tubing of 40mm bore including connections from trenches/walls/floors etc complete all as specified and as directed.

Taking up or down GI steel tubing of 50mm bore including connections from trenches/walls/floors etc complete all as specified and as directed.

Taking up or down GI steel tubing of 80mm bore including connections from trenches/walls/floors etc complete all as specified and as directed.

Taking up cast iron water mains 100mm bore (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed. Note:- Serviceable Lead shall be deposited in MES store yard

Taking up cast iron water mains 150mm bore (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed. Note:- Serviceable Lead shall be deposited in MES store yard

M&L 90mm outer dia,3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4(PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed.

M&L 63mm outer dia,3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4(PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed.

M&L 50mm outer dia,3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4(PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed.

M&L 40mm outer dia,3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4(PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed.

M&L 25mm outer dia,3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4(PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed.

S&F in repair, 25mm outer dia, PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

S&F in repair, 32mm outer dia, PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

S&F in repair, 40mm outer dia, PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

S&F in repair, 50mm outer dia, PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

S&F in repair, 63mm outer dia, PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

M&L in repair,Making connection of PP-R distribution branch with PP-R main of 16mm to 40mm outer dia by providing and fixing tee including cutting and making fusion joint etc. complete all as specified and as directed.

M&L in repair,Making connection of PP-R distribution branch with PP-R main of 50mm to 90mm outer dia by providing and fixing tee including cutting and making fusion joint etc. complete all as specified and as directed.

Supply, laying, jointing & testing of Ductile Iron (DI) Pressure 100mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-9 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed. Note- Excavation,DI Specials shall be measured and paid separately .

Supply, laying, jointing & testing of Ductile Iron (DI) Pressure 150mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-9 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed. Note- Excavation,DI Specials shall be measured and paid separately .

S&F DI Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.)Tee pieces single branch. "Y" junction, double branch, cross collars, caps and plugs for Pipe upto 150mm bore complete all as specified and as directed.

M&L Construction Brick Masonry Valve Pit of size 750x750x750 mm (Internal Dimension) one Brick thick Wall in Cement Mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggre-gate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40x5mm Flat Iron Frame alround including provision of Hinges, Handle with Locking Arrangement and 40x40 x6mm Angle Iron Frame fixed on top of Valve Pit by means of holdfast 150mm long, embedded in PCC 1:2:4 (20mm graded aggregate) Block of size 230x200x100 mm, applying two coats of Anti-corrosive Paint to all exposed Steel Surfaces over a coat of red oxide zinc chrome Primer after preparation of Surfaces and necessary Earth Work in Soft/ Loose Soil including demolition of unserviceable Valve Pit, complete all as specified and as directed.

Boring holes horizontally under Road without damaging the surface of Road (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 150 mm bore (dia) for passing of pipes, complete all as specified and as directed. Note:- GI pipe will be measured and paid seperately under appropiate item

Shree Krishna Traders (BID ID -3456688)