SPECIAL REPAIRS TO MT SECTION P-18 MT GARAGE P-83 G POL STORE P-13 AND R AND D SECTION P-83 AT BVY VISAKHAPATNAM

Amount

Dismantling floor, hearth or wall tiling including cement morter bedding (but not backing) , removing serviceable tiles to store and rubbish of the premises.

M&L Joint free non skid coloured ceramic, tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic colour tiles 450 X 300 X 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10 mm thick on fair faces of brick work or concrete surface in cement morter 1:4 as in backing of dado/skirting complete all as specified and directed.

M&L Joint free non skid coloured ceramic, tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and as directed.

Taking down chowkat with shutter (without taking off shutters from the frame) exc 1.5 Sqm but n exc 4.0 sqm each complete all as specified and as directed.

Supply and fixing Factory made UPVC white coloured sliding window three trackmade of external profile with wall thickness off 2.3mm (--0.2mm) window profile with halo section with multi chamber frame (88mm X 52 mm) sliding sash(42 mm X 67 mm) sliding mesh sash(42 mm X 16 mm ) will be mitered cut and fusuion welded at all corners including brailing of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware. EPDM gasket 1.2mm +0.2mm thick galvanized steel frame (30mm X 18 mm) 2 Nos Sliding Sash (30 mm X 18mm) Sliding mash sash (26mm X 10mm) Profile to be inserted in required profile frame will befixed to the wall with 8mm X 100 mm long fasteners Hardware. Touch lock of zinc alloyed (while poweder coated) steel roller system, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories .( Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet , edges painted to match with printed sheet complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS fram welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed.

S&F Anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing with poweder coating etc complete all as specified and directed.

S&F Anodised aluminum doors shutter aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges ,anodised aluminium snap beading screws with powder coating etc complete all as specified and directed.

S&F 5.5mm thick Sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq m in each pane for cup board, cabinet racks etc complete all as specified and directed .

S & F Anodised Aluminium window and ventilator shutters, slide hug type without sash bars, aluminum sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, snodised aluminum fitting such as peg stays 150mm long (1 No) , hings type B-21 100mm long (2 No) suitable handles, (1 No) with poweder coating complete all as specified and directed

S&F 2nd class hard wood as in plain straight chowkat and frames wrought framed rebeared on the solid rounded or charmfered but together with glue pinned at joints,etc complete all as specified and as directed

S&F 35 mm thick factory made 2nd class hard wood plain framed, panelled shutter with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneeing on both faces. The size of rail and stile as per IS: 1003 (Part-I), klin seasoned and chemically pressure treated, complete all as specified and directed.

S&F 50 micron thick solar control film reflictive type of make as approved by GE sticked to glass as per instructions of manufacturer complete all as specified and directed.

S&F 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations & other side balancing white laminations, fixed with screw to timber frame work complete all as specified and directed..

S & F in repairs cast iron body door closer hydraucally redgulated , designation No 3 universal type , suitable for door shutters of 851 to 1000 mm in width of weight betwwen 61 to 80 kg complete all as specified and directed..

S & F 100mm butt hings, extruded aluminum alloy with galvanised mild steel hings pin anodised and fixed complete all as specified and directed.

S&F 150 mm long Extruded Aluminum alloy handles , fabricated type , anodised complete all as specified and directed.

S & F 150 mm long aluminum , anodised barrel tower bolts of extruded section complete all as specified and directed..

S & F 30 mm long Aluminum , alloy , anodised sliding door bolt with hasp (bolt type) and fixing clips of sheet, cast or extruted section and fixing bolt and sliding bolts of extruted sections or cast aluminum alloycomplete all as specified and directed.

Aluminum frame work for grill, deco grill model DG-104 with 10 mm thick flat matt design making scope and level and fixed in 30 x 12 x 5 mm aluminium channe lwith necessary fixing arrangements etc complete all as specified and as directed.

S &F 4mm thick figured glass , pin head type and glazing with oil putty in squarenot exceeding 0.5 sq m in each pane complete all as specified and as directed

S & F 140mm Floor door stopper of Aluminum alloy body and tongue anodised with hard drawal steel spring fixed in floor complete all as specified and as directed.

Supply and Fixing in repairs 20 mm dia curtain roads of aluminum anodised fixed alongwith 2 Nos of brackets complete all as specified and as directed

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection laid to stop of 1:12, finished surface even and fair without using extera cement and including all necessary from work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection dully filled with mastic filling (One part of the bitumen 85/25 and three part of the fine sand by weight ) complete all as specified and directed.

Demolition of un-reinforced cement concrete above ground floor exceeding 15 cm thickness ( below or above ground level) complete all as specified and as directed

M&L for cement concrete 40mm thick type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in hard standing and paving even and smooth without using extra cement complete all as specified and as directed.

M&L for cement concrete 100mm thick type B-2 (1:2:4) using 40mm graded crushed stone aggregate as in hard standing and paving finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 20mm thick wearproof trooping as per manufacturers instruction using metallic floor hardner of make as approved by GE @ 4 kg per sqm, laid on concrete floor and paving, and finished and smooth including metallic floor hardner, applied when the base concrete is sufficently stiffiened complete all as specified and as directed

M&L for forming 12mm thick expansion joints filled with and including pre-formed bitumnous filler and top 30 mm primed and sealed with sealing compound , Grade "B'' for 100mm thickness of concrete slab complete all as specified and as directed.

S & F kota stone slab 25mm thick in riser of steps, skirting , dado and pillar laid over and including 20 mm thick cement screed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting and polishing complete all as specified and as directed

M &L for providing and injecting chemical emulsion anti termite treatment of soil under existing floors using chemical emulsion at the rate of one liter per hole, 300mm apart including drilling and plugging 12 mm dia, holes with cement morter 1:2 (1 cement: 2 coarse sand) to match witch existing floor complete all as specified and as directed

M & L providing and injecting chemical emulsion for anti termite treatment along the external wall below concrete or masnory apron using chemical emulsion at the rate of 2.25 liters per linear metre including drilling and plugged holes etc. in apron complete all as specified and as directed

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

S &F 20 mm bore UPVC pipes of pressure rating 10 kgf/sqcm fixed complete to walls, celling or in floors etc, any type pf pipes complete all as specified and as directed .

S &F 15 mm bore UPVC pipes of pressure rating 10 kgf/sqcm fixed complete to walls, celling or in floors etc, any type pf pipes complete all as specified and as directed .

S&F in rotational moulded polyethylene water storage tanks three layered (ISI Marked) 1000 ltrs capacity(cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old tank and removing complete all as specified and directed

S & F in repairs Vitreous China wash down water closet pan (pedestal pattern )with seat cover complete including provision of cement concrete bedding in PCC 1:2:4 complete all as specified and directed.

S&F in repairs PVC connection 15 mm dia 450mm long complete all as specified and directed

S&F in repairs vitreous china wash and basin, white, flat back, size 550 mm x 400 mm fixed on existing bracket, fixing of tap, waste fitting,pipe and union complete all as specified and as directed.

Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S & F in repairs Stainless stee Tubular towel rail , 20mm dia , D type 60cm long between flanges complete all as specified and as directed

S&F in repairs Health faucet with 1 m stainless steel flexible tube , wall hook, non return valve complete all as per Jaquar Catalouge No ALD-585 or its equivelent in Marc, Cera, parryware etc complete all as specified and directed

S & F in repairs 15mm mixing valve including three joints steel pipes or union add plugging screwing to wallscomplete all as specified and directed.

S&F in repairs 15 mm bore pillar tap, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified and directed.

S&F in repair 15 mm bore CP bib tap of fancy type with long shunk with cast copper alloy of crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule fixed complete all as specified and directed.

S &F 32mm bore dia of discharge pipe waste couping of PTMT (half or full threded) (min weight for 32mm to be 45gms) complete all as specified and directed

S&F in repairs 125mm dia stainless steel gratings with waste hole of min weight 100 gms complete all as specified and directed

S&F in repair 15mm bore CP stop cock with wall flange fancy type with long shunk with cast copper alloy of crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule of concealed type complete all as specified and as directed.

S & F in repairs 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for iron pipe and fixed. (minimum weight 455gms) complete all as specified and directed. .

S&F in repairs PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float & handle, & brackets complete set all as specified and directed.

S & F in repairs PVC waste pipe 32mm dia complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste : including bedding in cement morter to dwarf wall over and including fixing cantinlever brackets and connecting union to pipe overall size 915mm X 460 mm bowl size 410mm X 330mm X 160mm complete all as specified and directed.

Taking down rain water pipes including all fittings any size and pattern complete all as specified and directed

M&L for 110mm PVC (SWR) pipes single socketed in length with rubber ring joints fixed to walls/floors complete all as specified and directed.

M&L for 75 mm PVC (SWR) pipes single socketed in length with rubber ring joints fixed to walls/floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius with access door complete all as specified and directed

S&F 75 mm bore PVC (SWR) bends of any radius with access door complete all as specified and directed

S & F 75 mm bore PVC ( SWR) junction single T) equal or unequal with access door complete all as specified and directed .

S & F PVC (SWR) Floor trap of 75mm outlet with grating including jointing to waste pipe in run lead complete all as specified and directed.

S & F in repairs 20 mm dia Gun Metal, globe or Gate valve with iron wheel head screwed both ends for Iron Pipe and fixed complete all as specified and directed.

Removing the existing roof treatment completely inluding roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc and Brushing with neat cement slurry with 3 Kg of cement per squaremeter and Rendering 15 mm thick on fair faces of brick work or concrete surface in cement morter 1:3 and even and smooth without using extra cement including mixing of water proofing compound wherever required and providing APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application including coating the surface with water based bituminous primer blow bitumen of 85/25 @ 1.2 Kg/Sqm both at bottom and top of the membrance and finally finished with one coat of bitumenous aluminium primer at 100 gm per sqm complete all as specified and directed

M & L for Cutting / Chipping the spalled loose concrete of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Zinc rich epoxy primer to all steel surfaces as antirust agent and welding steel wire Fabric / Mesh of aperture 75mm and 2mm dia of wire to existing reinforcement, applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd as per manufacturer's instructions and providing pressure Guniting average 30mm thick at a pressure of not less than 6 KG / Sqcm in CM 1:3 duly mixing the mortar with and including polycrete admixture of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 2% of weight of cement, finishing the surface rough and finally rendering with 15 mm thick in CM 1:4 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics to match with the existing surface including providing double scaffolding and safety measures as required and removal of the same on completion and disposal of demolished materials / debris outside MD land complete all as specified and as directed.

Taking down cement or lime plaster of any description from stone or brick walls etc uncluding raking out, joijnts, hacking for key scrubbing down with water and dispossing of the rubbish matterial where directed at low lying areas in defence land complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement morter 1:4 and finished fair and even without using extra cement including mixing of water proofing compound complete all as specified and directed

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement morter 1: 6 and finished smooth and even without using extera cement complete all as specified and directed.

M & L for rendering 5 mm thick on fair faces of concrete surfaces in ceiling in cement morter 1:3 and finished fair and even without using extera cement complete all as specified and directed.

M & L preparing plastered or unplastered new surfaces by using vaccume based hand held or long handle sander machine and applying Three coat of white wash on walls/ceiling and cornices complete all as specified and directed

Preparing new previously untreated plastered or unplastered surfaces of any description and girth not otherwise described by using vaccume based hand held or long handle sander machine and applying 3 mm thick cement based wall putty by using automatic putty sprayer, (the putty shall be mixed with multipurpose mixer only) to achieve even and smooth surfaces and applying two coats of distemper oil emulsion by using Auto roller or Airless sprayer machine on surfaces of walls complete all as specified and directed.

M & L preparing plastered or unplastered new surfaces by using vaccume based hand held or long handle sander machine and cleaning the surfaces by using Jet washer and applying two coats of water proof acrylic emulsion paints, exterior grade (100% acrylic) over a coat of primer on prepared walls and cornices by using Auto roller or Airless sprayer machine complete all as specified and directed

S &F mild steel hold fast , clamps or similar small articles (conforming to Fe-410-0) complete all as specified and directed.

S & F 40mm bore of discharge pipe waste coupling of PTMT (half or full threaded) (min weight 60 gms) complete all as specified and directed

M & L preparing plastered or unplastered old decorated surfaces by using vaccume based hand held or long handle sander machine and applying Two coat of white wash on walls/ceiling and cornices complete all as specified and directed

Supply only Integral water proofing compound complete all as specified and directed.

Labour only for repair and servicing of rolling shutter and removing of worn component such as hood cover laths ball bearing helical wire springs, lock plates , brackets, shaft rod straighting of existing at required places including greasing and refixing in the same location as directed .

S & F 1.25mm thick steel rolling shutters, with out ball bearing , as specified including top cover, as-choring rod, hasp and staple and one shop coat of promer , erection in position as indicated complete: push pull or manual type gear operated type with bevel gear box and crank handles, complete all as specified and directed.

M & L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 m mean radius built in cement morter 1:6 inclusing demolition of old brick work complete all as specified and directed.

Preparation of new previously untreated wood surfaces of any description, over 10cm width or grith, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer by using auto roller or airless sprayer machine, complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and depth for foundations, etc not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and directed.

M & L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

S&F 150 mm dia Glazed stoneware pipes laid in trenches and jointed including dismantling of old pipes complete all as specified and directed

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate in pcc bed for 150 mm dia SWG pipes including packing under and haunching against the sides of pipe after they are laid complete all as specified and directed

Rendering 10 mm thick on fair faces of brickwork or concrete surfaces in CM 1:4 and finished fair and even without using extra cement complete all as specified and directed.

M&L PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate cast in situ in lintels , cills and other similar bands complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm thickness as in soil complete all as specified and directed.

Removing excavated material /soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Precast cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in landing and cover slabs etc and set in CM 1:6 complete all as specified and directed.

M & L for TMT bars 10 mm dia and over as in reinforcement cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel wire (annealed) not less than 0.9mm dia as in stirrups, spacers, binders complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150 mm dia of pipe complete all as specified and directed

Plain cement concrete 1:2:4 type B2 using 40 mm graded crushed stone aggregate as in surface channels and drains etc complete all as specified and directed.

Material and labour for modular point wiring with 1.5 Sqmm PVC insulated and unsheathed copper cable 1100V, FRLS grade multistranded drawn in and including 20mm PVC concealed/surface conduit in walls/ceiling with tee, bend, elbows,junction box etc. with provision of PVC insulated 1.5 sqmm copper conductor cable as earth continuity including 2.0mm thick prefabricated concealed galvanised boxes with white modular cover plate & frame of suitable size for fixing modular switches, sockets regulator and connected the earth wire to common earth dolly for One light/fan / bell point controlled by one switch complete including taking down old unserviceable point wiring all as specified and as directed. Note:-(i) All the disturbed surfaces of wall / ceiling shall be made good to match the existing wall / ceiling finishes and the rate also include all the cutting, chasing and cementing work for concealed wiring and as directed by the Engineer-in-Charge.

All as per item No 95 above but one 5A socket point controlled by one switch on independent board.

All as per item No 95 above but one 5A socket point controlled by one switch on same board.

All same as per item No 95 above but with 4sqmm PVC insulated unsheathed multistranded copper cable with one run of 4sqmm PVC insulated copper cable as earth continuity for power socket on independent board.

S & F in repair modular switch 1 way one module 6 Amps.complete all as specified and directed by the Engineer-in-Charge.

S & F in repair for modular socket out let 3 pin 5 Amps , 230V.complete all as specified and directed by the Engineer-in-Charge

S & F in repair modular socket 2 in 1, 3 pin, 6/16 Amps,complete all as specified and directed by the Engineer-in-Charge

S & F in repair modular switch 1 way one module 16 Ampscomplete all as specified and directed by the Engineer-in-Charge

S & F modular electronic fan regulator , complete all as specified and directed by the Engineer-in-Charge

S & F in repair ceiling rose surface backlite 3 terminals 65X50mm 230V including PVC Box of size 3"X3" round type. complete all as specified and directed by the Engineer-in-Charge

Material and labour for point wiring with 1.5 Sqmm PVC insulated and unsheathed copper cable 1100V, FRLS grade multistranded drawn in and including 25mm surface stove enamel steel conduit in walls/ceiling with tee, bend, elbows,junction box etc. with provision of PVC insulated 1.5 sqmm copper conductor cable as earth continuity suitable for flame proof switches, sockets regulator and connected the earth wire to common earth dolly for One light point/fan point controlled one switch including taking down old copper/aluminium point wiring aling with all fittings complete all as specified and as directed by Engr-in-Charge. all as specified and as directed, Note:-(i) All the disturbed surfaces of wall / ceiling shall be made good to match the existing wall / ceiling finishes and as directed by the Engineer-in-Charge.

Description all as per item No. 105 above but for 15/16Amp flame proof switch socket out let, independent with 4.0sqmm copper cable of PVC insulated, unsheathed, multi stranded and 4.0 Sqmm for earth continuity conductor, complete all as specified

M&L Switch flame proof switch socket and plug combined in LM6 cable with termination box in LM6 ,16A 250 volt,2P+earth complete all as specified and directed.

M&L Switch flame proof junction box with plane cover 3/4"139+E4 ET 80 complete all as specified and directed.

M&L Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V

M&L sub main wiring with 2 runs of 6sqmm PVC insulated unsehathed copper cable multistand 1100 V of FRLS grade with drawn in surface/ concealed (as per site requirement/ directed by Engr -in- Charge) PVC conduit not less than 25mm dia and one run of PVC insulated unsheathed 6 sqmm as earth continuity conductor drawn in PVC conduit with accessories complete,including taking out old UNSV submain wiring with accessories and making good to disturded surfaces complete all as specified and directed. NOTE (1): 3 runs of 6 Sqmm of copper wire and conduit will be measured as one unit i.e RM Note:-(2) Rate includes all cutting & chasing on existing wall/ceiling and also includes making good to match the existing wall / ceiling finishes the disturbed surfaces of wall / ceiling complete all as specified and directed by the Engineer-in-Charge.

M&L sub main wiring with 2 runs of 2.5 sqmm PVC insulated unsehathed copper cable multistand 1100 V FRLS grade with drawn in surface/ concealed PVC conduit not less than 19mm dia and one run of PVC insulated unsheathed 2.5 sqmm as earth continuity conductor drawn in non metallic rigid PVC surface/conceald PVC conduit with accessories complete, including taking out old UNSV submain wiring with accessories and making good to disturded surfaces complete all as specified and directed. NOTE (1): 3 runs of 4Sqmm, and 1 run of copper wire and conduit will be measured as one unit i.e RMNote:-(2) Rate includes all cutting & chasing on existing wall/ceiling and also includes making good to match the existing wall / ceiling finishes the disturbed surfaces of wall / ceiling complete all as specified and directed by the Engineer-in-Charge.

M&L for sub main 4 runs of 10 Sqmm for 3 Phases, neutral and one runs of 10Sqmm for earthing with PVC insulated unsehathed copper FRLS grade cable multistrand 1100 V grade with drawn in surface/ concealed PVC conduit/ 32/25mm dia with accessories including taking down old unserviceable submain wiring complete all as specified and directed. NOTE: 4 runs of 10 Sqmm with 01 run of surface PVC conduit 25mm dia/PVC Casing and caping will be measured as one unit i.e RM

Supply and fixing in repair of Factory made sheet metal enclosure double door SPN MCB DBs (Fixed flush to the wall), 240 volt, 4 Way, IP-42 protection with 200 Amp rated bus bar with suitsble size of copper PVC sheathed cable for earth continuity and suitable for having MCB’s including taking out old DBs any type and making good the disturbed surfaces by using plaster/ PCC/ cement work etc , complete all as specified and directed.

Supply and fixing in repair of Factory made sheet metal enclosure double door SPN MCB DBs (Fixed flush to the wall), 240 volt, 12 Way, IP-42 protection with 200 Amp rated bus bar with suitsble size of copper PVC sheathed cable for earth continuity and suitable for having MCB’s including taking out old DBs any type and making good the disturbed surfaces by using plaster/ PCC/ cement work etc , complete all as specified.

Supply and fixing in replacement of Factory made sheet metal enclosure for TPN MCCB DBs double door (Fixed flush to the wall), with provision of 100 Amps MCCB 4 pole as incommer & outgoing as TPN 415 volt, 6 Way, IP-42 protection with 200 Amp rated bus bar and copper PVC sheathed cable for earth continuity and suitable for having MCCB’s incomming and including taking out old DBs and making good the disturbed surfaces by using plaster/ PCC/ cement work etc complete all as specified

S & F in repair sheet metal enclosure single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB SPN 20 Amps capacity as per site requirement complete all as specified and directed by the Engineer-in-Charge

S & F in repairs MCCB 4 Pole, 100 Amps, 50 Hz, 16KA, 415 Volts,adjustable thermal and fixed magnetic type with all necessary aluminium lugs and glands, etc complete all as directed

S & F in repair 40 Amps MCB 415 Volt, TP/TPN, 50 Hz, "C" curve AC supply, as per site requirement complete all as specified and directed by the Engineer-in-Charge

S & F in repair 6 to 32 A MCB SPN 240 v "C" curve AC supply complete all as specified and directed by the Engineer-in-Charge

S & F in repair MCB SP 6 to 40 Amps 240 Volts, "C" curve AC supply as per site requirementcomplete all as specified and directed by the Engineer-in-Charge

Supply lay and testing of cable in trenches/walls XLPE insulated, armoured electric cable (heavy duty 1100volt grade with stranded aluminium conductor of size 25sq mm 4.0 core complete all as specified and directed by Engr-in-charge.

Taking down the existing any type and capacity of LED light/security light fitting and fixture from any location/position and, keeping in safe custrudy and refixing the same/new location with proper cleaning & by using of clamps nuts/ bolts/washer/ PVC copper cables etc as per ste requirements) after necessary ( B/R) and E/M work complete all as directed by Engineer-in-charge.

Labour charge for Taking down the existing AC any type and capacity (Window/split ) complete with outdoor/indoor fitting and fixture from its exiting location/position after diconnecting power supply and restoring refrigent gas and sealingpipe line and, keeping in safe custrudy and refixing the same/new location by using of clamps nuts/ bolts/washer/ PVC copper cables etc as per ste requirements) after necessary ( B/R) and E/M work complete all as directed by Engineer-in-charge.

S & F in repair for telephone socket with trasperent shutter 1 module , with provision PVC conduit 20 mm dia for incerting of telepfone cable complete all as specified and directed by the Engineer-in-Charge.

Taking down ceiling fans/exhaust fan/wall mounting fan from its position of any make, model,sweep, dismantling blades and removing fan and blades and cleaning/overlauling/servicing/repairing/greasing/oiling/rewinding the ceiling fan by using all spair parts such as bush/ knopy/ capacitor etc & painting the complete fan by using of spray paint of two coats and testing the fan and refixing the fan at old/new location complete all as specified and directed by Engr-in- Charge. Note:- the unit rate are enclusive of all spare parts & painting only rewinding of fan motor & two no of bearing will measure and paid separetaly in respective item . if required.

M&L for rewinding ceiling fan by using the suitable size/guage of super enamelled copper wire , with one set (two No bearings)and painting the complete fan by using of spray paint of two coats and testing the fan complete all as specified and directed by Enge-in- charge

M&L for rewinding Exhaust of any size by using the suitable size/guage of super enamelled copper wire , with one set (two No bearings)and painting the complete fan by using of spray paint of two coats and testing the fan complete all as specified and directed by Enge-in- charge

Materal and labour for renewal of earthing complete with GI earth plate elctrode 600x 600 x6.0 mm thick buried in ground not less than 2.25 mts deep below ground level with top edge of the plate not less than 1.5 meters below normal ground connected GI earth wire 4 mm dia fixed by means of bolts,nuts ,check nuts, and washers of galvanised iron GI pipe 25 mm dia perforated and top edge including necessary excavation earth work etc and earh pit size 300 x 300 x 300 mm with PCC type C1 1:3:6 RCC cover slab with type B1, 1:2:3 as per SSR plate No.5 and testing on completion incl taking down old unsv one.(Note:GI earth strip with GI protection pipe 40mm dia upto 7.5mtr from earth point is included in the unit rate considered).

M&L for 4mm GI wire for earthing connection to building, complete all as specified.

RL ENTERPRISES

ALLURI CONSTRUCTIONS

GVR CONSTRUCTIONS

GS ENGINEERS

GOLLAVILLI RAJANI KUMAR

S A R CONSTRUCTIONS

ANJANA ENTERPRISES