ARMO Work at FSD Sattenapalli for the year 202526 SH miscellaneous repair works in depot complex

Cleaning of Service drains around godowns in all depths and width 0.30m including removal of debris/ rubbish and disposal of the same in all leads and lifts filling in low lying areas and levelling complete in the depot premises as directed by the Engineer-in-charge and the drain to be kept clean during the period of monsoon.

Cleaning of Storme water drains in all depths and width 0.60m to 1.00m including removal of debris/ rubbish and disposal of the same in all leads and lifts filling in low lying areas and levelling complete in the depot premises as directed by the Engineer-in-charge and the drain to be kept clean during the period of monsoon.

Servicing to the rolling shutters including cleaning the side guides , springs and shaft etc., with kerosene oil, providing and applying fresh grease, applying tension to the springs replacing damaged parts and welding locking plates stoppers etc., wherever necessary etc complete as directed by the Engineer -in- Charge(Rolling shutters parts like laths, springs etc.. will be supplied at free of cost )

Tightening of EPDM screws in GI profile sheet roofing including fixing of missing screws, arresting roof leakage by providing and applying sealant compound/ GI washers and other roof leaking arresting materials wherever required over EPDM screws including providing safety measures for the labourers to work at higher elevation viz., ropes etc., insurance coverage for labourers and hiring of required T&P etc complete.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Disposal of building rubbish/malba/similar unserviceable,dismantled or waste materials by mechanical means,including loading,transporting,unloading to approved municipal dumping ground or as approved by Engineer-in-charge,beyond 50 m initial lead, for all leads including all lifts involved

Steel work welded in built up sections/ framed work, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer using,structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer in Charge.Internal work exposed on wall. 20 mm nominal dia Pipes

Providing and fixing white vitreous china type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making goad the walls and floors wherever required • W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china lat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing wash basin with C.I brackets 15mm dia CP brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required: a) white viterous china wash basin size 550x400 mm with a 15mm CP brass single hole basin mixer

Providing and fixing PTMT bib cock of approved quality, colour : 15mm nominal bore, 122 mm long, weight not less than 99 gms

Dismantling tile work in floors and roofs laid in cement mortar including stacing material within 50 metres lead :for thickness of tiles 10mm to 25mm

Providing and laying ceramic glazed floor tiles of size 300x300 mm or more (thickness to be specified by manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slutty @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer) of approved make in all colours, shades except bburgundy,bottle green,black of any size as approved by engineer-in-charge, in skirting,risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement:3 coarse sand) jointing with grey cement slutty @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment complete.

Dismantling doors, windows and clerestory windows(steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead Of area 3 sq. metres and below

Providing and fixing ISI marked flush door shutters conforming to IS:2202 (part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face weneers on both faces of shutters: 30 mm thick including ISI marked stainless steel butt hings with necessary screws

Providing and fixing ISI marked oxidised M.S handles conforming to IS:4992 with necessary screws etc. complete (copper oxidised as per IS 1378):125 mm

Providing and fixing ISI marked oxidised M.S tower bolt black finish, (Barrel type) with necessary screws etc. complete (copper oxidised as per IS 1378):250x10 mm

Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door,window,ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawing and the direction of engineer-in0charge (cost of aluminium snap beading shall be paid in basic item: : with float glass panes of 5mm thickness (weight not less than 12.50 kg/sqm)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal Of unserviceable material within 50 metres lead as per direction Of Engineer - in-charge.

Demolishing brick work manually by mechanical means including stacking o serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- harge.In cement mortar

Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (bothside inclusive) as per IS : 277 and consisting of angle cleats of size25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with ashfastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flangeof cleat fixed to the angle hangers of 5x10x0.50 mm of requiredlength with nuts & bolts of required size and other end of anglehanger fixed with intermediate G.I. channels 45x15x0.9 mm runningat the spacing of 1200 mm centre to centre, to which the ceilingsection 0.5 mm thick bottom wedge of 80 mm with tapered flangesof 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channelwith connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mmthick 27 mm high having flanges of 20 mm and 30 mm long, theperimeter of ceiling fixed to wall/partition with the help of rawl plugsat 450 mm centre, with 25mm long dry wall screws @ 230 mminterval, including fixing of gypsum board to ceiling section andperimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finishof tapered and square edges of the board with recommended jointingcompound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats ofprimer suitable for board, all as per manufacturer's specification andalso including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitablyfixed, all complete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix).

Supply of services of semi-skilled labour like carpenter, sewer man, plumber etc. on daily rate basis for day-to-day maintenance atleast weekly once as per direction of Engineer-in-charge.

Supply of services of labour like beldar, coolie, helper etc. on daily rate basis for day-to-day maintenance atleast weekly once as per direction of Engineer-in-charge

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level::1:2:4 (1 cement : 2 coarse sand (zone-lil) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler. 110 mm.

Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 75 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler. 75 mm

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in Width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in- charge. : All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level::1:4:8 (1Cement: 4coarsesand (zone-III)Derived from Natural Sources :8 graded stone aggregate 40 mm nominal size Derived from Natural Sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 1 cement : 4 coarse sand

Half brick masonry With common burnt day EP. S. (non bricks Of class designation 7.5 in fmandations and plinth in : cement mortar (I cement : 4 coarse sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating Coat Of neat Cement, including Cement Slurry, but excluding the Cost Of nosing Of Steps etc. complete. 40 mm thick with 20 mm nominal Size Stone aggregate.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain 100 mm diameter and 1.20 m Iong complete as per standard design.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, This includes jointing of pipes & fittings with one step CPVC solvent, cement, and testing of joints complete as per direction of Engineer in Charge. internal Work Exposed on wall. 32 mm nominal outer dia Pipes

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm