ADDITION/ALTERATION/RENOVATION OF MES OFFICERS MESS, SPECIAL REPAIRS TO WORKSHOP AND LT/HT CABLES ALONGWITH PANELS RESPECTIVELY AT INMAS AND SSPL LABS RESPECTIVELY, PROVISION OF EXTERNAL FACADE IN LABS OF KWC AREA AND PROVISION OF MAST LIGHTS IN MET

Amount

B/R (Portion) Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and including removing rubbish outside MoD land complete all as specified and directed.

Roughening surfaces of old concrete /terrazzo flooring by picking, sweeping clean and washing down with water to remove dust complete all as specified and directed .

M&L for laying double charged Vitrified Ceramic tiles (light shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, first quality coloured of grade B II (a) /B II (b) and of abrasion resistance PE-I-III or above etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed .

M&L for laying double charged Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm first quality coloured of grade B II (a) /B II (b) and of abrasion resistance PE-I-III or above, for work on vertical surfaces such as skirting / dado etc. set and jointed in neat cement slurry and pointed in colour cement to match tile over and including 10 mm thick rendering in Cement Mortar (1:4) complete all as specified and directed .

M&L for laying anti skid ceramic tiles 8mm thick coloured design (square /rectagular) area of each tile exc 0.11 sqm but n exc 0.18 sqm first quality coloured of grade B 11(a) /B 11(b) and of abrasion reistance PE-I-III or above in floors set jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed of Cement Mortar (1:6) complete all as specified and directed .

M&L for providing Glazed coloured design ceramic tiles 7 to 8mm thick area n.exc 0.36 Sqm each super glossy 1st quality of grade B tiles on vertical surfaces such as skirting /dado etc set and jointed in neat cement slurry and pointed in colour cement to match tiles over and including 10 mm thick screed bed in Cement Morter (1:3) complete all as specified and directed .

M&L for providing Glazed coloured ceramic tiles 300X 200X 7mm thick super glossy 1st quality of grade B tiles on vertical surfaces such as skirting /dado etc set and jointed in neat cement slurry and pointed in colour cement to match tiles over and including 10 mm thick rendering in Cement Mortar (1:3) complete all as specified and directed.

M&L for 25 mm thick Plain cement concrete (PCC) (1:2:4), type B0 (using 12.5mm graded crushed stone aggregate) as in sub floors and sub base floors to receive floor topping, complete all as specified and directed .

Demolition of plain cement Concrete of any description and in any position not otherwise specifically provided for and including removal of debris and rubbish out side defence land complete all as specified and directed.

M&L for 16 to 18 mm thick machine cut kota stone slab of size 520mmx520mm to 550 mm x 550 mm or as per site requirement laid as in flooring, tread / landing laid over and including 20 mm thick screed bed or bedding layer in Cement Mortar (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing complete all as specfied and directed.

M&L for providing machine cut kota stone slab 16-18mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in Cement Mortar (1:3), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing complete all as specfied and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons skirting etc laid bedded and pointed in any mortar and including removal from the out side defence land with mortar complete all as specified and directed

M&L for laying 16 to 18 mm thick machine cut mirror polished granite stone slab prefect black as in shelves , counter for wash hand basin , floor and window cill etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade / matrix of granite stone including grinding, moulding & polishing and bevelling half round edges of stones laid over and including 20 mm thick screed bed in Cement Mortar (1:4) complete all as specified and directed

M&L for providing 16 to 18 mm thick machine cut mirror polished granite stone slab perfect black on vertical surfaces such as skirting/dado, window sides etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, moulding & polishing and bevelling half round edges of stones fixed over and including rendering 10 mm thick in Cement Mortar (1:3) complete all as specified and directed

M&L for laying rubber/PVC moulded pre polished coulured concrete chequered tiles of size 300 x 300 x 25mm texture series in floor etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade / matrix of tiles laid over over and including 20 mm thick sereed bed in Cement Mortar (1:6) complete all as specified and directed.

Taking down steel/wooden chowkhats or frames (without taking off shutters from the frame) area n.exc 1.5 sqm each complete all as specified and directed

Taking down steel/ wooden/ Aluminium chowkats or frames or partitions( (without taking off shutters from the frames) area exc 1.5 Sqm but n exc 4 Sqm complete all as specified and directed Notes for Ser item No 16 to 17 :- Rate also included in this items for necessary cutting doors/taking out hold fast from the existing concrete /brick work and making good the disturbed surfaces with match existing surfaces after erecting new frames /chowkhats/partitions.

S&F Pressed steel frames for doors made out of 1.25mm thick MS Sheet hollow frame size 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, all as specified, and directed. Notes :- PCC filling to frame shall be measured & paid separately under respective item of BOQ.

S&F Pressed steel frames for doors made out of 1.25mm thick MS Sheet hollow frame size 105 x 60mm with one rebate including necessary fixing lugs, hinges, lock strike plate, etc., complete, all as specified, and directed. Notes :- PCC filling to frame shall be measured & paid separately under respective item of BOQ.

M&L for PCC (1:3:6) type C1 using (20 mm graded crushed stone aggregate) as filling steel frames, bed blocks for hold fasts etc complete all as specified and directed

S&F stainless steel barrel tower bolts, size 150mm and dia of shoot / bolts not less than 10mm of AISI 316 grade complete all as specified and directed

S&F stainless steel handle, size 150mm of AISI 316 grade complete all as specified and directed

S&F stainless steel butt hinges, size 100mm of AISI 316 grade complete all as specified and directed

S&F stainless steel sliding door bolts with hasp, staple of size 250mm long and dia of shoot not less than 12mm of AISI 316 grade complete all as specified and directed

S&F in repairs aluminum (die cast) body door closer hydraulically regulated, designation No 1 universal type, suitable for door shutters upto 700mm in width and of weight not more than 35 Kg complete all as specified and directed.

Easing and adjusting to shutter of any description, area exc 1.00 but n.exc 4.00 sqm each and includes taking down, refixing in the same opening including builders hardware as required complete all as specified and directed. Note : New builders hard ware fittings shall be measured and paid separately under respective item of BoQ.

M&L for 12 mm thick prelaminated particle board exterior grade with decorative choice laminations both sides for insertion to panels of aluminium shutters/partitions etc complete all as specified and directed .

M&L for 4.8 to 5.00mm thick obscured or frosted sheet glass n.exc 0.5 sqm in each pane over and including and fixing by means of glazing pins, rubber beading and glazing filling materials in panels of partitions, windows, doors etc complete all as specified and directed .

Dismantling wrought iron or mild steel in grill/guard bar (windows/ doors), railing, rolling shutters and steel work of any description not otherwise provided rolling shutters for complete all as specified and directed .

S&F mild steel framed work such as grills grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; framework of water tanks, hold fasts and similar work conforming to Fe 290 Gde E-165 complete all as directed.

M&L for preparation of new previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

Demolition of brick work or stone boulder masonry, built in cement mortar all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles including removal from the site complete all as specified and directed.

M&L for brickwork with fly ash old size bricks having compressive strength not less than 75 Kg/Cm2 straight or curved on plan exc 6m mean radius, built in cement mortar (1:6). complete all as specified and directed .

All as per srl item No 35.00 here-in-before but half brick thick walls built in cement mortar (1:4). complete all as specified and directed .

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal fo debris and rubbish out side defence land complete all as specified and as directed .

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces and fininshing the surface fair and even complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on other than fair faces of brick work or concrete surfaces (vertical walls surfaces) and fininshing the surface fair and even complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar (1:3) on brick work or concrete surfaces of ceiling and fininshing the surface fair and even cement complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified Notes : (i) Proposed washed stone grit plaster colour shall match with existing . (ii) White cement shall be used in lieu of ordinary cement in top layer of washed stone grit. (iii) Grooves shall be measured and paid separately,

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer -in-charge.

Complete removal of existing treatment from walls, fins, chajja etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including removing waste material/ debris outside MoD land complete all as specified and directed. Note Rate also includes necessary scaffolding to carryout work up to portion of building G+3 storey high.

All as per ser item No. 43.00 here-in-before but on ceiling/chajjas/sunshade including necessary scaffolding.

M&L for applying two coat wall care putty (each coat not less than 1mm thick) over newly plastered or old (complete removal of existing treatment) on wall/vertical surfaces to achieve an even finished smooth surface for applying finishes complete all as specified and directed.

All as per ser item No. 45 here-in-before but on ceiling/chajja/sunshade including scaffolding.

M&L for preparation of new plastered surfaces of walls and applying two coat of oil bound distemper priming plastered and other surface with alkaline resistant, preparatory to distempering complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coat of OBD, over a coat of chalk whiting on plastered surfaces preparatory to distempering complete all as specified and directed .

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for applying two coats of acrylic exterior emulsion weather proof paint of any tint including priming with alkali resistant primary paint on external new plastered/ putty surfaces for portion of building G+3 including necessary scaffolding complete all specified and directed.

All as per ser item No. 50 here-in-before but on ceilinjg, soffts of chajjas/sunshades including scaffolding.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for as in columns, roof slab, Chajja, shelves, lintel band & WHB counter and reinforcement cut as required to facilitate demolition, and removal debris and rubbish from out side defence land complete all as specified and directed

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. Note:- MS binding wire shall not be considered for purpose of measurements of weight.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in roofs/Chajjas, shelves, lintel bands etc complete all as specified and as directed

Providing form work to roofs, chajjas, RCC shelves, lintel band, and similar work including edges fair finished surfaces of flat concrete complete all as specified and directed

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern) of size 350 x 475x390, 'S' trap in, white including PVC seat cover with mild steel chromium plated hinging device & EWC Jet chromimum plated with 1.00 m long (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed. Make Jaquar Cat part No V N S-WHT-551 PNP 18422 or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F in repairs Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of concrete bedding and removal of waste materials/debris out side MoD land complete all as specified and directed.

S&F in repair Wall Hung Water Closet with all accessories :- (i) Wall Hung water closet of size 370 X 545 X 370 mm including UF soft self close seat cover, hinges, in builts, jets & including all accesories. Make Jaquar Cat part No DRS-WHT-37953UFSM or equivalent in make/ manufacturers as given in Appendix 'B' to PS. (ii) Slim Concealed Cistern with Floor Mounting Frame, Installation Kit P type and Drain Pipe Set for Wall Wall Hung WC (Without flush Control Plate) complete. Make Jaquar Cat part No V N S-JSA-WHT-2400WP equivalent in make/ manufacturers as given in Appendix 'B' to PS. (iii) Control Plate Segment White/Chrome Slim for concealed cistern compete. Make Jaquar Cat part No JCP-CHR-852415 or equivalent in make/ manufacturers as given in Appendix 'B' to PS. (iv) Control stop cock suitable for cistern coomplete.

S&F in repairs Vitreous China wash basin, white, flat back, size 550 x 400 mm including PVC waste pipe, chain and plug and porcelain stopper, CP waste fitting 32mm dia and PVC bottle trap etc complete all as specified and directed .

S&F in repairs UPVC 32 mm bore pipe of presure rating 10 Kgf/Sqcm , complete all as specified and directed.

S&F in repairs vitreous china Table top /oval type (under/over counter wash basin) white size 600x400mm including CP waste fitting 32mm dia and CP bottle trap etc complete all as specified and directed . Make Jaquar Cat part No KVS-WHT-35935 or CERA cat part No S022103WT or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F in repairs vitreous china half stall urinals, olympus star, white complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, CP urinal Spreader fixed to water supply pipe, CP waste coupling, grating and union for discharge pipe complete all as as specified and directed . Make Jaquar Cat part No URS-WHT-132530 and CERA cat part No S4020112 or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F in repairs 10mm thick Urinal partition made of, frosted acrylic sheet glass of size 450 x900mm in chrome fininsh complete all as specified and directed. Make Jaquar Cat part No JSE-CHR-810 UC450X or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 ltr capacity, low level white with inlet ball valve, float, ,handle and brackets including fittings flush pipe 32mm bore complete all as specified and directed . Make Jaquar Cat part No WHC-WHT-184NL or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F in repairs bib taps long body chromium plated cast copper alloy fancy type with crutch or butterfly handle screwed down suitable for iron pipe or brass ferrule of 15 mm bore complete all as specified and directed . Make Jaquar Cat part No KUP 35037PM or cera cat No F-2008152 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs pillar tap fancy long body push type time duly screwed for iron pipe and fixed 15mm dia bore complete all as specified and directed . Make Jaquar Cat part No KUP 35021PM or Cera cat part No F 1002101 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F 15mm bore brass chromium plated single lever tall body basin mixture without pop up waste system with 450 mm long braided hoses etc complete all as specified and directed. Make Jaquar Cat part No KUP 35005BPM or Cera cat part No F2008461 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs chromium plated fancy Angle/stop valve high pressure with crutch or butter fly handle screwed both end for angle valves cast copper alloy, screwed iron pipe or for unions and fixed 15mm bore dia complete all as specified and directed . Make Jaquar Cat part No KUP 35053PM or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed . Make Jaquar Cat part No ALD805A or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs chromium plated health faucet, teliphonic type,with CP flexible arms and Jet, suitable to fixed and including 15mm bore CP angle valves, etc complete all as specified and directed. Make Jaquar Cat part No ALD 573 or OR Cera health faucet cat part No F 8030301 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs toilet paper holder Chromium plated brass complete all as specified and directed. Make Jaquar Cat part No AQN-7753 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs tubular towel rail,wall thickness not less than 1 mm, 20mm dia, D type, 60cm long between flanges of brass chromium plated bracket complete all as specified and directed . Make Jaquar Cat part No ACN-1111NN or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs brass chromium plated bottle trap 32 mm bore including jointing to waste fitting and pipe complete all as specified and directed. Make Jaquar Cat part No ALD769L 300X190mm or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs chromium plated soap dish, any type, fixed to plug with chromium plated brass screws complete all as specified and directed . Make Jaquar Cat part No AKP 35731P or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F in repairs Push Button liquid soap containers with ABS body of capacity 0.80 ltr fixed with chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed. Make Jaquar Cat part No AKP-35735P or equivalent in make/ manufacturers as given in Appendix 'B' to PS

Dismantling old unserviceable PVC water storage tanks of capacity exc 250 ltrs & n.exc 500 Ltrs including supplying & fixing of any colour PVC water storage tank 500 ltr capacity HDPE, IS-12701 Marked double layered , cylindrical vertical type fixed and hoisted in position on roof at any height of building complete with inlet/outlet of 20mm outer dia 3 layer PP-R pipe connection including closed top with locking arrangement including supply & fixing ball valves high prsessure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm dia and the minimum weight of valves 210 grms complete all as specified and directed by Engr-in-Charge Note : Inlet, outlet & wash out pipe will be measured and paid separately.

Dismantling old unserviceable PVC water storage tanks of capacity exc 500 ltrs & but n.exc 1000 Ltrs including supplying & fixing of any colour PVC water storage tank 1000 ltr capacity HDPE, IS-12701 marked double layered , cylindrical vertical type fixed and hoisted in position on roof at any height of building complete with inlet/outlet of 25 mm outer dia 3 layer PPR pipe connection including closed top with locking arrangement, including supplying & fixing Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight of valve 210 gms ) complete all as specified and directed by Engineer-in-Charge Note : (Inlet, outlet & wash out pipe will be measured and paid separately.

S&F in repairs nipple of PTMT suitable for HDPE water storage tank of size 20mm bore dia of pipe (Minimum weight -45gms ) complete all as specified and as directed .

Supply and fixing in repairs gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe of 15mm bore dia complete and fixed all as specified and directed by Engr-in-charge.

All as per srl item No 80 here-in-before but 20 mm bore dia.

Taking down 15mm bore steel water tubing and connections from any position including removing from the site complete all as specified and directed.

All as per srl item No 82 here-in-before but 20 mm bore dia.

All as per srl item No 82 here-in-before but 25 mm bore dia.

S&F 16 mm outer dia, pipe 3-layer PP-R Polypropylene random copolymer (concealed pipes SDR 7.4 (PN 16) UV stabilized) and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed to walls, ceilings or in floors / roofs etc complete all as specified and directed . Note:- Cutting chases for concealed pipes & fittings etc wherever required and making good, disturbed surface in Cement mortar 1:3 shall be deemed to included in the unit quoted rate.

All as per srl item No 85 here-in-before but 20 mm outer diameter.

All as per srl item No 85 here-in-before but 32 mm outer diameter.

M&L for making connection of PP-R distribution branch with PP-R main of 16 to 40mm outer dia sizes by providing and fixing tee including cutting and making fusion joint complete all as specified and directed .

Dismentelling old unservicable cast iron pipe including fittings of 100mm dia from walls, floors/ ground etc complete all as specified and directed.

All as per srl item No 89 here-in-before but 75 mm internal dia.

S&F UPVC pipe size 110mm for soil, waste, and vent, Type-B as per IS-13592 suitable for rubber ring joints, including all necessary specials and fittings (Confirming to IS-4735) such as bends, tees , junctions (with or without doors), reducers, WC connectors, couplers, cowels, clamps, rubber rings etc, fixing at walls/ceiling/floor supproted by MS clamp & hangers etc in concealed/inside duct/under floor & basement ceiling/external work etc. including chase cutting if required upto 04 storeyed high building and making good distrubed surfaces with existing.

All as per serial item No 91 here-in-before but but 75 mm.

Dismantling of wall panelling and ceiling board (Fibre,pulp,insulation etc.) or insulation board /slab/blankets any thickness including cover fillet , GI Frame work and hangers /rod etc complete all as specified and directed by Engr-in-Charge.

S&F GI powder coated frame work for seamless false ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 0.9m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre or fixed with 6mm dia GI hanger (upto 1.2m) with ceiling cleat made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5 mm dia, 40mm long complete all as specified and directed

Cutting openings, through brick walls built in cement mortar, for door, windows and other openings or enlarging existing openings, converting window into door openings, etc. including providing, fixing and removing shoring, and brick/brick bats including mortar from the premises. complete all as specified and directed.

M&L for water proofing treatment to sunken portion complete all as specified and as directed in the following operations:- (a) Firstly removing/taking out all lean concrete/mud/brick bats as retrieved from site. (b) Rendering 15mm thick in CM (1:4) mixed with water proofing compound @ 2% by weight of cement including the cost of water proofing compound. (c) After drying of plastered surface, suitable primer such as multiplas primer/muliplas/cold sticker/ multiplas blown bitumen VG-10 shall be coated on the plastered surface. (d) MULTIPLAS @ 3 Kg/Sqm shall be unrolled over the coated surface (with overlap of 10cm) and bonded completely to the primed surface. The overlap shall then sealed by the tourch flame. (e) Toping with PLASFAL @ 2 Kg/Sqm. A layer of blown bitumen of VG-10 is applied @ 1.20 Kg/Sqm on MULTIPLAS. Plasfal memberan shall then be bonded on top of MULTIPLAS. (f) Re-filling the material which is obtained from above ser No (a) of this item before laying the concrete. Note:- (i) The above water proofing treatment shall be carried out by a specialized agency as approved by GE(I) upto G+3 floor without any extra cost. (ii) Minimum 10 years guarantee period for any leakage/seepage in sunken portion to be rendered by the Contractor/Firm on non judicial stamp paper of an amount of Rs 10.00. (iii) Concrete filling if required shall be measured & paid separately.

S&F aluminium frame duly powder coated not less than 50 micron thick for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed by Engr-In-Charge.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position.

S&F aluminium section duly powder coated not less than 50 micron thick for window grills complete with necessary 'U' shaped aluminium channel alround fixed in window frame /opening with screws complete all as specified and directed

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint complete all as specified.

M&L for applying two coats of synthetic enamel paint over one shop coat primer on factory made steel surfaces such as pressed steel frame, factory made steel windows/vents, rolling shutters etc complete all as specified and directed.

M&L for preparation of new wood or wooden based surfaces of any description, over 10 cm in width or grith not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

All as per srl item No 100 here in before but on wood or wooden based surfaces.

S&F powder coated aluminium snap grid of size 595 x 595 mm to 605 x 605mm frame work for false ceiling complete all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for providing Gypsum Board 12mm thick cornices up to 150 mm wide along the false ceiling on vertical surfaces fixed with cadmium plated steel as per manufacturers instructions complete all as specified.

M&L for 600 x 600 x 10 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre fixed in frame work of ceilings complete all as per manufacturer's instructions complete all as specified and directed

S&F in repairs 15mm bore pillar taps fancy type, CP brass with capstan heads, scewed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nut, screwed for iron pipes or brass ferrule of 15mm bore fixed in position complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to wall with mild steel clamps after taking down old unservicable existing C.I. soil /waste/vent pipes complete all as specified and directed.

S&F in repairs PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

S&F in repairs doom type PTMT grating 100/110 mm dia with waste hole fixed on floor / nahani trap fixed with cement mortar (minimum weight 25 gms) complete all as directed.

M&L for providing cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B, (using 40mm graded crushed stone aggregate), filling of sunken flooring and mass-concrete complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorugated etc) in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F in repairs aluminium door closer (die cast body) hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in position complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawings shown on ser page No 160 of SSR Part-II (Rates)

Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing as shown on ser page No 161 of SSR Part-II (Rates)

M & L for factory made steel rolling shutter thickness of laths 1.00mm thick gear operated type with bevel gear box and crank handle, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type all as specified and directed.

S & F safety lever locks mild steel with 4 levers including 2 Nos keys for rolling shutters complete all as specified and directed.

S & F ball bearing suit to rolling shutters complete all as specified and directed.

S&F factory made steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded. Conforming to IS of Z section complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed.

S & F factroy made steel ventilators with top hung shutters made out of Z sections including hinges, steel peg stay complete all as specified and directed.

Supply only stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm of 26 gauge and fixed with stainless steel wire staples/ MS /wooden beading complete all as specified and directed. Note :- Wooden beads shall be supplied with shutters.

M&L for French polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

S&F butt hinges, 100mm size extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F brass handles cast type of 150mm size bright polished complete all as specified and directed.

S&F 300mm long brass, sliding door bolt with sand or die cast brass hasp, staple (bolt type) and fixing bolts with rolled or drawn brass bolts and fixed complete all as specified and directed.

S&F 200 mm long,brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts etc complete all as specified and directed

S&F 150mm long Floor door stopper of brass body and tongue, with hard drawn steel spring fixed in floor,complete all as specified and directed.

S&F aluminium section duly powder coated not less than 50 micron thick for swing door shutters partly panelled and partly glazed comprising top rail 85.00x44.45x2.70mm (Jindal Al Section No. 19563), bottom rail 150x44.45x2.20 mm (Jindal Al Section 19517), lock rail 150x44.45x3.00 mm (Jindal Al Section 19596) and styles 47.62x44.45x1.62mm (Jindal Al section No. 19526) and including joining cleats, alum snap beading (Jindal Al section No. 19360), rubber gasket glazing clips and two nos disc type handle and one nos alum tower bolt 200mm long for each leaf on one side and one 6 lever dead lock of brass with for each leaves fixed in position complete all as specified and directed . Note :- Insertion of glass pane/ prelaminated particle board shall be paid and measured seperately under respective items of BOQ.

S&F aluminium section powder coated not less than 50 micron thick for windows/ cupboard framed shutters (fixed/ openable/three track sliding) frame made out of alum frame of section 63.50mmx 38.10mm x1.60mm thick and shutter fixed or open able / horizontal and vertical members of aluminium section 47.50x44.45x1.60mm thick of aluminium beading rubber gasket, aluminium fittings such as 2 Nos hinges type B 21, of size 100 mm long, tower bolts 150mm long ( 2 Nos), 100mm stay rod (1 Nos) and one handles 125mm for each leaf complete all as specified and directed. Note :- Insertion of glass pane/ prelaminated particle board shall be paid and measured seperately under respective items of BOQ.

Supply & Fixing aluminium (powder coated not less than 50 micron thick with approved colour) ventilator, partly glazed and partly louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (section No 20036) of Jindal, half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including stainless steel wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete all as specified and directed. Note:- (i)Section/catalouge given above are of make Jindal, Contractor may use similar section of other make mentioned in Appendix 'B' to PS. (ii) Insertion of glass pane shall be measured and paid separately under respective item of BOQ.

S&F in repair grating doom type 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed .

Supplying & fixing UPVC floor / nahani trap of size 110 mm x 90 mm of self cleansing design with CP Jalli fixed to it with white or coloured cement complete all as specified and directed.

All as per item No 136 here-in-before but (110 x110 mm).

All as per item No 136 here-in-before but (110mm size) multifloor trap.

Supplying & fixing UPVC gully traps of size 160 mm x 110 mm with self cleansing design with CP Jalli fixed with white or coloured cement single / double size as per site reuirement complete all as specified and directed.

Supply and fixing in position stainless steel plate rack of size and design as approved made out of 1.00mm thick stainless steel (Salem sheet) and having weight between 9.0 Kg to 9.5 Kg each complete all as specified and directed.

Supply and fixing 20 mm dia outer stainless steel powder coated curtain rods with wall thickness not less than 1 mm including stainless steel powder coated, bracket, holding and funnel on ends as fixed complete all as specified and directed .

S&F in repairs PVC soap tray , 350 x 100 x 60mm, fixed to wall with plugs and chromium plated brass screws of suitable length complete all as specified and directed.

S&F glass shelf assembly consisting of 5.5mm thick acrylic sheet 12cm wide with chromium plated brackets, guard and railing 60cm long complete all as specified and directed. Make Jaquar Cat part No CAN-1173 or equivalent in make/ manufacturers as given in Appendix 'B' to PS

S&F 125mm to 175mm hat pegs of aluminium, solid body fixed with screws complete all as specified and directed.

Supply and fixing in repairs cast copper alloy ABS body chromium plated overhead rain shower rose fancy type of size 200mm x 200mm in square shape with Rabit Cleaning system including shower arms 600x25x25mm suare shape for wall mounted shower with flange fixed to 15mm bore pipe complete all as specified and directed. Make Jaquar Cat part No OHS-35497 for overhead rain shower and Cat part No SHA 455L600 for shower arms or equivalent in make/ manufacturers as given in Appendix 'B' to PS.

S&F of Stainless steel (Grade 304) hollow tubes sections, channels, plates, angles etc of any size and sections as approved by GE in railings, balusters,post, newel posts running rails ,middle rails etc including necessary welding, reveting, bolting, grinding, buffing, polishing and making curvature (wherever required) including necessary accessories, framework for sign board / indication board including taking down exixting steel sections etc complete all as specified and directed.

M&L for laminated wooden flooring/wall panelling as per approved sample 8mm thick size 1216x192mm with interlocking pannels, of AC 4 grade3 as per EN 13229 standards, samll embossed surface with glossy finish complete all as specified and directed :

Material and labour for HDFT-moulding with exactly the same shade matrix as that of the flooring planks for skirting not exceeding 10 cm high complete all as specified and directed.

S&F Seamless calcium silicate ceiling12 mm thick made out of 1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish complete all as specified and directed. Note :- (Frame work for ceiling shall be measured and paid separately)

S&F Factory made precast concrete heavy duty drain/ manhole covers including MS frame duly painted with two coats of synthetic enamel paint over one coat red oxide zinc chrome primer reinforcement as per IS 12592 : 2002 of any thickness complete all as specified and directed.

S & F toughened frosted glass 12mm thick with aluminium frame fixed window in wall with clips / including fixing acessories, with necessary grouting unit or any LOGO emblemb on glass complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 as in rafters, purlins, vertical posts etc complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) of grade Fe 410.W (Gde-E-250) quality A, channels, square cut or notched (ordinary and counter sunk) forming holes including riveting, welding etc complete all as specified and directed.

Supply and fixing in repair sinks with drainage board made of stainless steel 1 mm thick for kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf walls or including fixing cantilever brackets and connecting union to pipe over all size (915mmx460mm bowl size 410x330x160mm) complete all as specified and directed.

S&F full overlay MS clips on hinges with high quality nickle plated suitable for any type of board upto 24mm thick complete all as specified & directed.

S&F wire baskets made of top quality 304 grade Stainless Steel wires with NiCr plating (Ni 4%) of approved design & pattern.

S&F of machine crafted box type cabinet using 19mm thick prelaminated particle board duly edge banded with 2mm thick PVC Lipping/ band of approved shade on both faces. Utensil baskets drawer made out of stainless steel grade 304 (The wire basket shall be measured & paid separately), running on ball bearing Telescopic slides/channel provided for kitchen vessels & accessories including fixing zinc plated drawer channels (TDC) of size 20 inch with necessary nuts & bolts, doors provided with locking device as per manufacturers instructions. The shutter shall be fixed by using full overlay MS clips on hinges with high quality nickle plated suitable for any type of board upto 24mm thick complete all as specified & directed complete Note : This item and Item No 155 & 156 above shall be used for making of modular kitchen accessories.

M&L for 18/19mm thick Prelaminated particle, board, exterior grade,prelmainated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to frame work complete all as specified & directed

M&L for 10-12mm thick anti skid pavement digital vitrified tiles light shade of area n.exc 0.36 sqm each having antiskid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match tiles laid over & including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed

Material and labour for repair to chajja/ roof Projection using PCC 1:2:4 type B-O or dubbing out average 20 mm thick including taking down/demolation of loose concrete particles, and porviding all necessary form work and finishing the exposed surfaces of concrete even & smooth with 5mm thick rendering in cement mortar (1:3) complete all as directed.

Material and labour for 75 mm thick cement concrete type C-1, 1:3:6 ( using 20 mm graded crushed stone aggregate) as in plinth protection/path laid in bays including finishing the concrete surface even and fair without using extra cement complete all as specified. (Note : - The unit rate quoted shall be deemed to include the provision for laying the concrete in alternate bays n. exc 2 m each in length each with 12mm wide and 50mm deep joints between every bays which shall be filled with mastic filling with hot bitumen 85/25 and sand in 1 : 2 mix volume complete all as specified and directed.

M&L for 35 mm thick factroy made plain framed panelled shutter rail & style of 2nd class hard wood (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated rail and style made out of 2nd class hard wood complete all as specifed and directed.

All as per Srl item No 162 -here-in-before but 40mm thick, covered with hot pressed at factroy premises with 0.9 mm thick decorative laminate type-I, of surface finish, colour and pattern as approved on both faces, complete all as specified and directed.

M&L for 35 mm thick factroy made glazed & skelton shutter of 2nd class hard wood open rebated and prepared to reccive glass, gauge etc (with out sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.24 (a) wood kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, farmed rebated on the solid, rounded or chamfered , put together with glue pinned at joints in position complete all as specified and directed at site.

Factory made solid panel PVC door shutter 30mm thick (Style) , consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm without stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing shown on srl page No 156 of SSR Part-II.

S&F stainless steel barrel tower bolts, size 200mm long and dia of shoot/ bolts not less than 10mm, steel AISI-316 grade complete all as specifed and directed.

S&F stainless steel butt hings, size 75mm medium weight of AISI-316 grade steel complete all as specifed and directed.

M&L for 100mm thick cement concrete type B-2 (using40mm graded crushed stone aggregates) as in sub floors , subbase laid in alternate panel/ way finishing surfaces even and rough to receive the topping layer including necessary use and waste form work complete all as specifed and directed.

M&L for wearproof topping 18mm thick (incorporating an approved metallic floor hardner) laid on concrete floors and paving and finished even & smooth (except metallic hardner) complete all as specifed and directed. Note :- Metallic floor hardner shall be measured seperately and paid at supplied only)

Supply only metallic floor hardner complete all as approved.

M&L for forming construction (Dummy) joints 65mm deep & 10 mm wide filled with sealing compound grad 'B' complete all as specifed and directed.

Supply only glass dividing strips, 32mm thick and 38mm in width inserted in position conform to design complete all as specifed and directed.

S&F in repairs 32mm bore dia of discharge pipe waste coupling of PTMT (half or full threaded) minimum weight 45 gms suitable for wash hand basin complete all as specifed and directed.

Material and labour for Rough cast plaster including 15mm thick rendering in cement mortar (1:3) on brick work or concrete surfaces complete all as specified in para 14.22 of SSR pat-I (2009) and directed.

M&L for chipping off spoiled and loose concrete and cleaning rust from reinforcement by sand blasting scrubbing down concrete surfaces with wire brushes cleaning with water allow to dry and applying a layers of Zinc rich epoxy primer as an antirust on all exposed reinforcement steel bars followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 2 mm dia of wire and appruture 75 mm, total thickness of guniting not exc 40 mm (Avg thickness) in Cement mortar (1:2) using OPC 53 grade cement mixed with polycreate mixture @2% by weight of cement or as per menufacturer instructions and finally appyling cement plaster over gunite surface of requred thickness to give even , uniform and smooth finishes confirming to proper geometric in cement mortar (1:3) to match the existing surfaces as in sides ,soffits of the slabs,chajja,fins,facia ,parapets,lintels,columns, beams etc complete including necessary scaffolding ,shuttring,necessary chasing to brick work or RCC members at any hieght up to 04 storey buildings including removal of all small trees/shurbs (including roots) etc complete all as specified and as directed. Note:-Rate also includes in this item for necessary provision of scaffolding to carry out work upto portion of building G+3 storeys high.

Material and labour for clearing away all vegetation, saplings, shrubs, brushwood , undergrowth, digging out roots, filling holes and levelling ground, stacking of serviceable material and trees not exceeding 30 cm girth and removing rubbish outside the MOD land complete all as specified and directed. Note:- (a) The cleaning of vegitable/brushed growing to be cleaned upto G+3 storey high building and making good with PCC 1:2:4 type B1 and finishing the surface to match the existing surface complete all as specified and directed. (b) Rate also includes in this item necessary scaffolding, tools & plants to carry out the work upto a height G+3 high.

Taking down old existing wood hand rail under 40 Sqcm section from steel balusters of stair cable / Balcony etc complete all as specified and directed.

Demolition of cement conceret in ground floors and paving n exe. 15 cm thickness (below or above ground level) and including removal of rubbish out side MoD land complete all as specified and directed.

E/M (Portion) Taking down unserviceable point wiring any type for light, fan, power etc including unserviceable switch,socket, regulator light fitting and ceiling rose etc of any make complete including making good disturbed surfaces of walls ,floors roof etc with existing surfaces complete

Taking down of Celling/Exhaust Fan (of any description) carefully and deposit in safe custody and refixing the same after painting with synthetic enamel white paint by spraying machine, including marking MES No,greasing,minor repairing on the completion of the work complete all as specified and directed.

M&L for Point wiring with 2 single core 1.5 Sqmm multistranded copper conductor cable multistranded, FRLS PVC insulated and unsheathed in non metallic PVC concealed connduit 20 mm bore dia with necessary fitting including cutting chasing for conduits and terminal boxes with all fittings /accessories and including 1.5 Sqmm FRLS PVC insulated copper earth wire connected to common earth with terminal boxes for Modular fittings including acessories as modular surface cover plate with frame, for one light/Fan/Exhaust Fan/bell point complete all as specified and directed.

All as per srl item No 182 here- in- before but using cable size 1.5 Sqmm for 1 Nos 06 Amps Socket outlet independent with terminal boxes, Modular fittings including acessories as modular surface cover plate with frame, metal flush box,complete all as specified and dierected.

All as per srl item No 182 here- in- before but using cable size 1.5 Sqmm for one light point controlled by 02 Nos two way modular switches complete all as specified and dierected.

All as per srl item No 182 here- in- before but using cable size 1.5 Sqmm for 1 Nos 06 Amps Socket outlet on the same board with other switches complete all as specified and as dierected.

All as per srl item No 182 here- in- before but using cable size 2.5 Sqmm for 15/16 Amps Socket outlet independent terminal boxes for Modular switches.

All as per srl item No 182 here- in- before but using cable size 4.00 Sqmm with 4.00 sqmm earth wire for one three pin switch socket outlet 15/16 Amps point independent with terminal boxes.

S&F sheet metal single pole and neutral enclosure with 2 pin and earth plug top and socket complete with one single pole MCB 20 Amps C curve 240 V complete all as specified and directed (Cat No 507811 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S&F modular switch 6 Amp single pole one way-1 module complete all as specified and directed (Cat No 574800 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S&F modular switch 15/16 Amp single pole one way-1 module complete all as specified and directed (Cat No 574808 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S&F modular socket outlet shuttered-6A-5 Pin-universal India 2 Module complete all as specified and directed (Cat No 574833 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S&F modular socket outlet shuttered-6/16A-5 Pin Indian 2 Module complete all as specified and directed (Cat No 574834 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S&F electronic fan step type regulator 120W - 2 module complete all as specified and directed (Cat No 574831 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

S & F modular switch 6 amps , 230 V AC, 2 way, one module complete all as specified and directed.

M&L for Ceiling rose surfave type Bakelite 65x50mm two to three terminal 230V PVC/polycarbonate, isolated body all as specified & directed.

M&L for Modular Bell push 6 Amp 2 Module complete all as specified (Cat No 574824 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

M&L for Bell multi music type 230 V AC, complete all as specified and directed.

M&L for MCB single pole & Neutral 63 Amps. C Curve 240 V complete all as specified and directed (Cat No 408620 of Legrand or equivalent in make as given in Appendix 'B' to P.S.

M&L for MCB single pole 6-32 Amps C Curve 240 Volt complete all as specified and directed Make Legrand or equivalent in make as given in Appendix 'B' to P.S.

Material and Labour for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below and above 15 cm of earth plate. GI plate connected with galvanised iron strip of 25x4mm by means of GI nuts, bolts and washers. Strip laid in 40mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) complete all as shown in electric plate No 3 of SSR Part-I with following:- (a) GI strip of size 25x4mm. (b) Watering pipe GI medium grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm internal dimension constructed in PCC 1:2:4 type B1 120 mm thick wall over PCC lean concrete foundation 500 mm x 500mm x 150mm thick, exposed surfaces of concrete smoothly finished with 15mm thick cement mortar (1:6) including RCC 1 :2:4 type B1 reinforced with 8mm dia deformed bars @100 mmc/c bothways pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm for 30x30 cm PCC pit for holding the pit cover. (e ) Apply two coat of synthetic enamel paint over one coat of red oxide zinc chrome primer on exposed steel surfaces and two coat of hot tar on embedded portion of steel surfaces.

All as per srl item No 200 here- in- before but earth plate connected with 32 x 6mmmm GI strip in repairs/ renewal.

M&L for Galvanised iron strip 25x4mm buried in ground including necessay excavation & earth work in soft/loose soil and removal of surplus excavated material n. exc 50m and depositing where directed.

All as per srl item No 202 here- in- before but 32x6 mm earthing lead in renewal/ replacement.

All as per srl item No 202 here- in- before but 4 mm dia G. I. wire earthing lead.

All as per srl item No 202 here- in- before but 4mm dia G.I. wire earthing lead in renewal/ replacement.

Material and Labour for earthing in any type of soil complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below and above 15 cm of earth plate. GI plate connected with galvanised iron wire 4mm dia by means of nuts, bolts and washers. GI wire laid in 15 mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) complete all as shown in doctric plate No 3 of SSR Part-I with following:- (a) GI wire of size 4mm . (b) Watering pipe GI medium grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm (internal dimension) 120mm thick wall in PCC 1::4 type B1 on 500x500x150mm PCC base 1:3:6 concrete exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC 1:2:4 type B-1 pit cover 25mm thick reinforced with 8 mm dia deformed bars @ 100 mm c/c both ways with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover and angle iron frame of 40x40x4mm complete. (d) Angle iron frame made of 40x40x4 mm for 30x30 cm PCC pit for holding the pit cover. (e ) Apply two coat of syntheticnenamel paint over one coat of red oxide zinc chrome primer on exposed steel surfaces and two coat of hot tar on embedded portion of steel surfaces.

All as per srl item No 206 here- in- before but in renewal / repairs earthng set complete.

Supply and Fixing in renewal of sheet metal enclosure, single pole and neutral with two pin and earth plug and socket complete with one single pole MCB SP, C Curve type of capacity 32 Amp,240V, 10 kA complete all as specified and directed.

Supply and fixing, in renewal of triple pole and earth enclosure with three pin and earth plug with socket complete (Industrial type DB) with and including one MCB TP, C Curve type of capacity 63 Amp, 10 kA , 415 volt complete all as specified and directed.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 2x4.00 sqmm+1x4 sqmm earth wire of FRLS PVC insulated copper conductor single core cable in and including rigid non metallic PVC conduit pipe not less than 25 mm external dia including all accessories completeall as required or all as specified and as directed by Engineer-in-charge.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 4x6 Sqmm+2x6 Sqmm earth wire of FRLS PVC insulated copper conductor single core cable in and including rigid non metallic PVC conduit pipe not less than 25 mm external dia including all accessories completeall as required or all as specified and as directed by Engineer-in-charge.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 4x10 sqmm+1x10 sq mm earth wire of FRLS PVC insulated copper conductor single core cable in and including rigid non metallic PVC conduit pipe not less than 25 mm external dia including all accessories completeall as required or all as specified and as directed by Engineer-in-charge.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 4X16 sqmm+1X16 sqmm earth wire of FRLSH PVC insulated copper conductor single core cable in and including rigid non metallic PVC conduit pipe not less than 25mm dia including all accessories complete all as required or all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs of MCB DB sheet metal enclosure double door SPN 12 way with 240 V rated busbar complete all as directed.

Supply and fixing in repairs of MCCB, 415 volts, four pole of capacity 125 Amps, 25 KA, ICS = 100% ICU, with Thermal - Magnetic Release, including spreader terminals / thimble of suitable size and making connections complete all as specified.

Supply and fixing in repairs of MCB, C Curve type suitable for 415 volts AC supply, TP with over load and short circuit protection and rupturing capacity not less than 10 KA and 100 Amps capacity complete all as specified and directed.

Supply and fixing in repairs of MCB, C Curve type suitable for 240 volts AC supply, DP with over load and short circuit protection and rupturing capacity not less than 10 KA and 40 Amps capacity complete all as specified and directed.

S&F in repairs of telephone socket jack with shutter RJ-11, complete all as specified & directed.

S&F DLP U PVC trunking system Plastic adoptable type 150x50mm with two compartment duly covered installed with suitable support joints including all accessories complete all as specified and as directed.

Supply and fix in relacement of LED tube light fitting Decorative ultra slim polycarbonate LED lighting fixture with high lumen output, environmental friendly, along with fixture 4 feet, 22 Watt and making all electric each connections with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and directed. Make: Havells Cat Part No. LHEXBLP7PN1W022 or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of LED luminaire, 2x2, 24 W recess mounted pressure die cast aluminium luminaire in powder coated white finish with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and directed. Make Havells Cat Part No. LHEAABP7IN1W024 or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of wall lamp opal glass 5 watt LED with chrome finish including all necessary fixing arrangements with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Model No KCH-CHR-MB 160275531B OF Jaquar or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of Environmental friendly, ultra modern, energy saving, surface mounted, decorative Bulkhead 13 Watt designed for modern homes available in non PIR as well as PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer of high brightness LED with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Cat Part No LHEXCFP7PN5W013 of Havells or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of Surface mounted LED downlighter 15W with white powder coated aluminium housing with integrated electronic driver with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Cat Part No ENDURANEOHESURFA CEDLS15WLED840S of Havells or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of Linear & compact 10W LED 6500K Mirror light fitting with decorative grey end caps, polycarbonate body and ribbed opal diffuser including provision of cable for making electric connection from ceiling rose or connection to LED with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Cat Part No LHEXACP7IN1W010 of Havells or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of recess mounted ADORE LED 3 W DEEP SPOT BLUE with white powder coated aluminium housing with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Cat Part No LHEEBCP1UN1B003 of Havells or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of Recess mounted round fixture with opal diffuser and separate electronic driverLED downlighter 15W with white powder coated aluminium housing with three core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm complete all as specified and as directed. Make: Cat Part NoLHEBADP5IZ1W015 of Havells or equivalent in make as given in Appendix 'B' to P.S.

Supply and fixing in replacement of MCB distribution board double door vertical type made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating, VTPN 12 way. 415 volts with bus bar rating 200 Amps, dust and vermin proof and IP 43 - IK 09 protection suitable for incorporation of incomer MCCB and outgoing MCBs, including grouting in the wall, cutting & chasing etc complete all as specified. Make- L&T Cat No DBPGL012DD or equvalent in make as given in Appendix 'B' to P.S.

Supply and fixing of MCB distribution board double door type made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating, SPN 8 way. 240 volts with bus bar rating 200 Amps, including grouting in cement mortar 1:3 in the wall after necessary, cutting & chasing and making good complete all as specified and directed.

Supply and fix online booster of 1 HP Capacity with tank and auto on off mechanism with Automatic Pressure Controller Suitable for 1 HP water pump single phase, noiseless , built in thermal protection , easy to install and silent running , low maintenance, extended pump life, maximum operating temperature-60 C Up to 10 Bar Pressure, Voltage 220V -240V, frenquency 50/60 Hz, Max rated current 10 A , Max. Allowable pressure 10 Bar, built in thermal protection including fixing arrangement necessary wiring and starter complete all as specified and directed.

Taking down the existing split AC of 1.5/2 ton capacity from its existing position and refixing at the same or new location/ position after carrying out minor repair woks including gas charging as required and servicing the same complete all as specified and directed.

S&F auto clean eletric cheminey filter less technology with air flow upto 1250 Cum/hr touch control , single phase of size 90cm (3-5 burner stove for wall mounted chimneys) noise level 68dB , warranty 1 year on product and 5 year on motor including stainless steel ducting of 100 mm dia of 5 mtr length powerful motor for efficient suction capacity, position inside chimney makes clear path of smoke and air chimney makes kitchen oil and smoke free auto clean helps in getting rid off oil particles itself with one touch. It prevents oil and grease particles which affect the suction power of chimney. Chimney cone with LED lamps , it will give perfect amount of light while cooking and also ensure the long durability and lesser noise level to give cool environment in kitchen with touch control it enables ease opertaion with just one touch, oil collector cup collection oils and other residuals making it easy to keep the chimney clean complete all as specified and directed. Note : After completion of work contractor shall furnish wirtten warranty on ten ruppes non judicial stamp paper for smooth working of chimney and motor.

Supply and fixing exhaust fan 380 mm sweep, heavy duty, four blade, double ball bearing , 1400 RPM minium air dilivery discharge 350 cubic meter per hrs suitable for SP , 230/250 Volts, AC supply with louvres shutter complete to fix in schedule 'A' section -III. Note :- Fan shall of make Cromption , cat Ref : EXHD380-4-1 or or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of LED light fitting surface/recessed mounted 2x2 of capacity 34W complete with all connected accessories. Make:- Havells Cat No LHEWEIP7PW1W034 or equivalent in make as given in Appendix 'B' to P.S. .

S&F in replacement of Batten type luminaire pre-wired for T-8 LED 18W tube light complete with batten, LED tube,Celling rose, double side connection & lamp Holders . Make:- Havells cat No. LHLDDAXEUL8Z018 for LED tube and LHFYBWP1TB1W020 for batten or equivalent in make as given in Appendix 'B' to P.S.

S&F in replacement of Powder coated pressure die cast aluminium SMD LED street light wirh heat resistant toughened glass of capacity 45 Watt including taking down old unserviceable and suitable bracket for fixing of street light complete all as directed .(Cat LTESS145WLED/LS of C&S or equivalent make as given in Appendix 'B' to P.S.

M&L in renewal for MCB TP&N distribution board suitable for TP'G' frame MCCB , 4 way double door vertical type including incomer MCCB 16 kA 125 Amps Adjustable thermal (70% to 100%) & Fixed magnetic setting type complete all as specified and directed by Engr-in-charge.

S&F in replacement of in door type cubical panel board suitable for 3 phase, 4 wired, 415V, 50 Hz and tested at CPRI for 35 MVA rapturing capacity at 415 volts factory fabricated with CRCA sheet not less than 2.00 mm thick having modern fabrication process powder coating in approved shade having thickness not less than 100 microns provided with suitable gasket to make it dust and vermin proof and general constructions conforming to IS : 8623/93. The LT Panel shall be front and back openable and having inner and outer shells. The inner shells duly compartmentalized for each control gears. The panel should have suitable size of copper bus -bar three phase 4 wired system having current carrying capacity not less than 1.2 times the rated current carrying capacity of the incomer ACB/MCCB. (PCC 1:3:6 type C-2 platform of suitable size or as per manufacturers insructions for mounting the feeder pillar box is deemed to be included in the quoted rate ) and to accommodate the following incoming and outgoing fixture / fillings duly fixed/ mounted with suitable link/ plates complete all as specified & directed . INCOMING (i) MCCB 250 A 4 pole, 25 KA - 1 No. (ii) Digital Multi functional meter VAFPP (voltage, current,frequency, power factor-1 No. (iii) Phase indicator lamp (LED type) 1 ste (set of three). OUT GOING (i) MCCB 125 A 4 pole, 16 KA -02 Nos. (ii) MCB TPN 63 A -10 Nos. (iii) MCB DP 32 A -10 Nos Note :- The rate is quoted including Incoming and Outgoing switchgears .

M&L for bricks having compressive strength not less than 75 kg/sqcm laid dry in trenches for cable protection complete all as specified and directed.

Excavation in tranches n. exc. 1.5m wide & n. exc 1.5 m in depth for foundation, etc or for shafts, manholes, pier holes or for taking up or down or laying of cables, water pipes etc. and getting out in soft/loose soil complete all as specified & directed.

All as per srl item No 240 here-in-before but hard/dense soil.

Returning, filling in, including spreading, levelling watering and well ramming in layers not exceeding 25 cm thick as in soft/loose soil complete all as specified and as directed.

Removing excavated materials, soil, n.exc 50m away distance and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified & directed.

M&L for river screened sand filling for cushion of underground cable with layer of sand 8 cm deep before laying and 15 cm deep after laying of cables complete all as specified & directed. Note : Punned down thickness will be considered for payment of sand cushion of cables

Supplying and laying un-reinforced precast concrete (M-30) cable cover, class HV, Type 1, flat, size 300mmx 180mm x 40mm complete all as specified & directed.

Supplying and laying un-reinforced precast concrete (M-30) cable cover, class LV, Type 1, flat, size 250mmx 150mm x 40mm laid in trenches for cable protection complete all as specified & directed.

M&L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified & directed.

M&L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 25x20cm size complete all as specified & directed.

M&L in replacement of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 11000 volts, (earthed) grade with multi stranded aluminium conductor conforming to IS-7098, including cable gland, cable lugs for termination cable of cross sectional area 185 sq. mm 3 core complete all as specified & directed.

M&L in replacement of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 11000 volts, (earthed) grade with multi stranded aluminium conductor conforming to IS-7098, including cable gland, cable lugs for termination cable of cross sectional area 120 sq. mm 3 core complete all as specified & directed.

M&L in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts (earthed) grade with multi stranded aluminum conductor conforming to IS-7098 including cable gland , cables lugs for termination cables of cross-sectional area 120 sq. mm 3.5 Core complete all as specified & directed.

M&L in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade with multi stranded aluminum conductor conforming to IS-7098 including cable gland , cables lugs for termination cables of cross-sectional area 185 sq. mm 3.5 Core complete all as specified & directed.

M&L in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with multi stranded aluminum conductor conforming to IS-7098 including cable gland , cables lugs for termination cables of cross-sectional area 240 sq. mm 3.5 Core complete all as specified & directed.

M&L in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade with multi stranded aluminum conductor conforming to IS-7098 including cable gland , cables lugs for termination cables of cross-sectional area 400 sq. mm 3.5 Core. Note :- For srl item No 254 to 259 excavation , earth work , brick protection and sand cushion shall be measured & paid separately.

M&L in repairs Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm to 185 sqmm complete all as specified & directed.

Supply, installing, testing and commissioning factory made and tested LT Indoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system having bus bar chamber with insulated electrolytic Aluminium bus bars 1600 A 3 Strips & Neutral 800 A aluminium 1 set installed on DMC insulators with bus bar chamber the panel shall be dust and vermin proof, and inner sheet made out of 2.00 mm thick CRCA mild steel sheet and mild steel & Mounting Channel frame work made out of MS angle 75X40 X 6mm duly coated with zinc metal coating, front opening type for installation of separate cable alleys, busbar chamber and switchgear compartments. Provision in cable alleys to be kept for bottom cable entry for incoming and outgoing cables. A clear space of 200 mm to be kept from floor level for switchgear compartment. Extended busbar links/ terminals to be provided for heat dissipation, air ventilation breathers to be provided for heat dissipation. Suitable sized knock-out holes for cables, gland shall be provided as per respective schematic drawing of the following equipments/ instruments each compartment shall be numbered/ letterd as per the approved drawing affixed MV Danger plate as suitable intervals/ location, panel board compartment size should be suitable to accomodate the switchgear and other accessories as per IE rules, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLSH cable of adequate size but not less than 1.5 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy based make as per shade approved after taking proper shutdown before dismantling / taking down old rusted panel including PCC & Brick work complete all as specified and as directed. (a) INCOMING -ACB 1000 A 50 KA 4 POLE ADJUSTABLE TYPE 1 NO (b) OUTGOING -MCCB 400 A 35 KA 4 POLE ADJUSTABLE TYPE 3 NOS (c) MCCB 250 A 25 KA 4 POLE ADJUSTABLE TYPE 2 Nos (d) MCCB 100 A 25 KA 4 POLE ADJUSTABLE TYPE 2 Nos (e) DIGITAL MULTI FUNCTION METER ( V+A+F+PF ) 1 No (f) INDICATING LIGHT RED 220V AC 1 No (g) INDICATING LIGHT YELLOW 220V AC 1 No (h) INDICATING LIGHT GREEN 220V AC 1 No (i) PROTECTION MCB 6 A SP 3 NOS. REPUTED (j) C.T. 1000/5 A 3 NOS (k) DANGER PLATE 1 NO. (l) BUS BAR CHAMBER 1600 A 3 STRIPS & NEUTRAL 800 A ALUMINIUM 1 SET (m) ENCLOSURE OF SIZE : 1875 X 1600 X 900 MM 1 No

All as per srl item No 256 here -in- before but 1800 A 3 Strips & Neutral 900 A aluminium 1 set and consisting/mounting the following accessories /fixtures/fittings:- (a) INCOMING -ACB 1200 A 50 KA 4 POLE ADJUSTABLE TYPE 1 NO b) OUTGOING- MCCB 400 A 36 KA 4 POLE ADJUSTABLE TYPE 3 NOS (c) MCCB 250 A 25 KA 4 POLE ADJUSTABLE TYPE 2 NOS (d) MCCB 100 A 25 KA 4 POLE ADJUSTABLE TYPE 2 NOS (e) DIGITAL MULTI FUNCTION METER ( V+A+F+PF ) 1 NO (f) INDICATING LIGHT RED 220V AC 1 NO (g) INDICATING LIGHT YELLOW 220V AC 1 NO (h) INDICATING LIGHT GREEN 220V AC 1 NO (i) PROTECTION MCB 6 A SP 3 NOS (j) C.T. 800/5 A 3 NOS (k) DANGER PLATE 1 NO. (l) BUS BAR CHAMBER 1200 A 3 STRIPS & NEUTRAL 600 A ALUMINIUM 1 SET (m) ENCLOSURE OF SIZE : 1875 X 1600 X 900 MM 1 NO.

All as per srl item No 256 here -in- before but LT out door type made of 3.15 mm thick CRCA mild steel sheet, having aluminium bus bar 1800 A 3 Strips & Neutral 900 A aluminium 1 set and consisting/mounting the following accessories /fixtures/fittings:- (a) INCOMING -ACB 1200A 50 KA 4 POLE ADJUSTABLE TYPE 1 NO (b) OUTGOING- MCCB 400 A 36 KA 4 POLE - 1 NOS (c) MCCB 250 A 25 KA 4 POLE ADJUSTABLE TYPE 3 NOS (d) MCCB 100 A 25 KA 4 POLE ADJUSTABLE TYPE 3 NOS (e) DIGITAL MULTI FUNCTION METER ( V+A+F+PF ) 1 NO (f) INDICATING LIGHT RED 220V AC 1 NO (g) INDICATING LIGHT YELLOW 220V AC 1 NO (h) INDICATING LIGHT GREEN 220V AC 1 NO (j) PROTECTION MCB 6 A SP 3 NOS (k) C.T. 800/5 A 3 NOS (l) DANGER PLATE 1 NO. (m) BUS BAR CHAMBER 1200 A 3 STRIPS & NEUTRAL 600 A ALUMINIUM 1 SET (n) ENCLOSURE OF SIZE : 1600 X 1400 X 600 MM - 1 NO.

All as per srl item No 256 here -in- before but LT out door type made of 3.15 mm thick CRCA mild steel sheet, having aluminium bus bar 1600 A 3 Strips & Neutral 300 A aluminium 1 set and consisting/mounting the following accessories /fixtures/fittings:- (a) INCOMING -MCCB 400 A 36 KA 4 POLE ADJUSTABLE TYPE 1 NO b) OUTGOING- MCCB 250 A 25 KA 4 POLE ADJUSTABLE TYPE 4 NOS (c) MCCB 100 A 25 KA 4 POLE ADJUSTABLE TYPE 2 NOS (d) DIGITAL MULTI FUNCTION METER ( V+A+F+PF ) 1 NO (e) INDICATING LIGHT RED 220V AC 1 NO (f) INDICATING LIGHT YELLOW 220V AC 1 NO (g) INDICATING LIGHT GREEN 220V AC 1 NO (h) PROTECTION MCB 6 A SP 3 NOS (j) C.T. 400/5 A 3 NOS (k) DANGER PLATE 1 NO. (l) BUS BAR CHAMBER 600 A 3 STRIPS & NEUTRAL 300 A ALUMINIUM 1 SET (m) ENCLOSURE OF SIZE : 1500 X 1300 X 500 MM 1 NO.

All as per srl item No 259 here -in- before but aluminium bus bar comprising the following accessories /fixtures/fittings:- (a) INCOMING -MCCB 400 A 50 KA 4 POLE ADJUSTABLE TYPE 1 NO b) OUTGOING- MCCB 200 A 25 KA 4 POLE ADJUSTABLE TYPE 2 NOS (c) MCCB 100 A 36 KA 4 POLE ADJUSTABLE TYPE 2 NOS (d) DIGITAL MULTI FUNCTION METER ( V+A+F+PF ) 1 NO (e) INDICATING LIGHT RED 220V AC 1 NO (f) INDICATING LIGHT YELLOW 220V AC 1 NO (g) INDICATING LIGHT GREEN 220V AC 1 NO (h) PROTECTION MCB 6 A SP 3 NOS (j) C.T. 400/5 A 3 NOS (k) DANGER PLATE 1 NO. (l) BUS BAR CHAMBER 600 A 3 STRIPS & NEUTRAL 300 A ALUMINIUM 1 SET (m) ENCLOSURE OF SIZE : 1500 X 1300 X 500 MM 1 NO.

Supply and installation, testing & commissioning of Galvanised steel high MAST LIGHTING SYSTEM OF 16 Meter high mast shafts in two sections Top dia 200mm and bottom dia 460mm suitable for 47m/s wind speed, with latching type head frame, winch mounting bracket, lumanaries, carriages suitable to install 08 Nos 240 W LED lumanaries in symmetrical arrangement with including 6 core 2.5 sqmm multistranded copper conductor cable for connection of LED light fittings and Aviation light to LT panel complete including RCC foundation work as per manufacturer design and provision of raising lowering system comprising double drum SWL of winch, and 6 pole single speed 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor 1 HP , manual handle, junction box, including necessary GI strip/copper wire separate earthing connection for lightening finial and fixing of foundations bolts 08 Nos of size 850mm long 30mm dia manufactured from special steel along with nuts, washers, anchor plate and common template and fixing Aviation light comprising of aluminium housing with polycarbonate enclosure including necessary excavation & earth work in any type of soil and foundation as per OEM inspection complete all as specified and directed at site. NOTE : (i) Wind tunnel test certificate carried out successfully by reputed institutes should have with the manufacturer and contractor shall have to submit the same before approval of make/manufacturers name. ii) Technical specifications, foundation all as specified and shown on drawings. (iii) LED lights shall be measured and paid separately.

Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor cross sectional area of size 16 Sqmm 4 Core complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor cross sectional area of size 25 Sqmm 4 Core complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor cross sectional area of size 240 Sqmm 3.5 Core complete all as specified and directed. Note :- for srl item No 267 to 269. Excavations, earth work, sand cushion and cable protection cover shall be measured & paid seprately under respective items of BOQ.

S&F LED Flood light 240 watt with pressure die cast aluminium housing complete with all accessories. Model No. JETAPROPLUSFL240WLED757LTG of Make Havells or equivalent in make as given in Appendix 'B' to P.S.

S&F LED street light 120W watt with pressure die cast aluminium housing complete with all accessories all as specified and directed. Model No. ENDURACITYLINERNEOSL120WLED757SASYBOTG of Make Havells or equivalent in make as given in Appendix 'B' to P.S.

M&L for boring of holes under road, pavement, hard standing in any length by trenchless techonology using ultra sound technique/mannually/mechanically suitable for 100 mm dia GI pipe for passing through cables and with necessary machine mechanism complete all as specified and directed.

Supply and laying GI pipe light grade of 100mm dia with all fittings laid in trenches for protection of UG cable complete all as specified and directed.

All as per ser item No. 268 above but 80mm dia.

All as per ser item No. 268 above but 50mm dia.

Taking down existing steel tubular /PCC pole 9 mtr long including necessary earth work, breaking of PCC , shifting to new location after carrying out necessary excavation and earth work in soft/loose soil including filling and compacting excavated ditch with soil complete all as specified and directed .

M&L for erecting of pole retrieved serviceable from ser item No. 272 above including necessary excavation & eath work in soft/ loose soil providing/ fixing of new Junction box SMC KIOSK box water proof IP-54 of size 140x140x95 mm including fixing of terminal connector 100A 4 pole suitable for in and out connection of 4 core cable fixed on pole complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) for pole foundation filling in road /pavements cutting and similar locations complete all as specified and as directed.

Supply, installing, testing and commissioning factory made panel size 1200mm x 600 mm x 1700 mm and tested CPRI approved LT Panel indoor type, double door, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system, IP-54 having bus bar chamber with insulated electrolytic Aluminium bus bars TPN of capacity 800 Amps rating installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and inner & outer sheet made out of 2.00 mm thick CRCA mild steel sheet & Mounting Channel frame work made out of angle iron 75X40 x 6 mm duly coated with zinc metal coating, front opening type for installation of separate cable alleys, busbar chamber and switchgear compartments. Provision in cable alleys to be kept for bottom cable entry for incoming and outgoing cables. A clear space of 200 mm to be kept from floor level for switchgear compartment. Extended busbar links/ terminals to be provided for heat dissipation. Air ventilation breathers to be provided for heat dissipation. Suitable sized knock-out holes for cables, gland shall be provided as per respective schematic drawing of the following equipments/ instruments. Each compartment shall be numbered/ letterd as per the approved drawing. Affixing MV Danger plate as suitable intervals/ location, panel board compartment size should be suitable to accomodate the switchgear and author accessories as per IE rules, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLSH cable of adequate size but not less than 2.5 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy based make as per shade approved by Engineer-in- charge, after taking down the Old rusted panel from it's position after taking proper shut down all as specified and as directed. BUS BAR CHAMBER:- (a) 800 Amps 3 phase & Neutral 800 Amps, Aluminium conductor E-91 grade, with color coded heat shrinkable sleave and shall be mounted on, non combustible, track resistant, high strength DMC material, interconnection of all incomings & outgoings. INSTRUMENT CHAMBER:- (i) Digital Multi Function Meter with LED display for measurement of Voltage, current, frequency, Power Factor, etc. 415 Volt, 3 Phase - 01 Set. (ii) C.T's of capacity 600/5 A Cl 1.0 - 01 Set. ( Set of three ) (iii) Red, Yellow, Green Phase indicating Lights LED type 220 V 50 Hz - 1 Set. ( Set of three ). (iv) Suitable Protection MCB C Series- 1 Set. ( Set of three ). INCOMING SUPPLY :- (i) MCCB 400 Amps, breaking capacity 36 KA 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS= 100% ICU= 02 No., (ii) On load change over switch 400 Amp 4 pole - 01 No OUTGOING SUPPLY :- (i) MCCB 160 Amps, 25 KA, 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS=100% ICU= 02 Nos., (ii) MCCB 100 Amps, 25 KA, 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS=100% ICU = 05 Nos. (iii) Onload Change over switch 320A= 01 No

Supply, installing, testing and commissioning factory made panel size 1200mm x 600mm x 1700mm, CPRI approved and tested LT panel outdoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system, IP-54 having bus bar chamber with insulated electrolytic Aluminium bus bars TPN of capacity 800 Amps rating installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and inner sheet made out of 3.15 mm thick CRCA mild steel sheet & Mounting Channel frame work made out of angle iron 75X40 x 6 mm duly coated with zinc metal coating, front opening type for installation of separate cable alleys, busbar chamber and switchgear compartments. Provision in cable alleys to be kept for bottom cable entry for incoming and outgoing cables. A clear space of 200 mm to be kept from floor level for switchgear compartment. Extended busbar links/ terminals to be provided for heat dissipation. Air ventilation breathers to be provided for heat dissipation. Suitable sized knock-out holes for cables, gland shall be provided as per respective schematic drawing of the following equipments/ instruments. Each compartment shall be numbered/ letterd as per the approved drawing. Affixing MV Danger plate as suitable intervals/ location, panel board compartment size should be suitable to accomodate the switchgear and other accessories as per IE rules, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLSH cable of adequate size but not less than 2.5 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy based make as per shade approved by Engineer-in- charge, after taking down the Old rusted panel from it's position after taking proper shutdown all as specified and as directed. BUS BAR CHAMBER:- (a) 800 Amps 3 phase & Neutral 800 Amps, Aluminium conductor E-91 grade, with color coded heat shrinkable sleave and shall be mounted on, non combustible, track resistant, high strength DMC material, interconnection of all incomings & outgoings. INSTRUMENT CHAMBER:- (i) Digital Multi Function Meter with LED display for measurement of Voltage, current, frequency, Power Factor, 415 Volt, 3 Phase - 01 Set. (ii) C.T's of capacity 600/5 A Cl 1.0 - 01 Set. ( Set of three ) (iii) Red, Yellow, Green Phase indicating Lights LED type 220 V 50 Hz - 1 Set. ( Set of three ). (iv) Suitable Protection MCB C Series- 1 Set. ( Set of three ). INCOMING SUPPLY :- (i) MCCB 400 Amps, breaking capacity 36 KA 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS= 100%ICU = 02 No., (ii) Onl load chage over switch 400 Amp, 4 pole-01 No. OUTGOING SUPPLY :- (i) MCCB 160 Amps, 25 KA, 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS=100% ICU= 03 Nos., (ii) MCCB 125 Amps, 25 KA, 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS=100% ICU = 02 Nos. (iii) MCCB 100 Amps, 25 KA, 4 Pole, Adjustable type, Microprocessor release 415 volts, 50Hz, ICS=100% ICU = 02 Nos. (iv) Onload Change over switch 320A= 01 No

M & L for PCC (1:2:4) type B-2 (using 40 mm graded crushed stone aggregate) as in coping of poles etc including necessary form work and surfaces finished even and smooth with using extra cement complete all as specified and directed.

Supply and fixing in replacement of telephone wire two core of size 0.5 mm dia complete all as specified and directed.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 2x6 Sqmm+1x6 Sqmm earth wire of FRLS PVC insulated copper conductor single core cable in and including rigid non metallic PVC conduit pipe not less than 25 mm external dia including all accessories completeall as required or all as specified and as directed by Engineer-in-charge.

Salaria Builders

Leo Network power systems

Flint India

M/s Himgiri construction