TENDER FOR CIVIL/ INTERIOR/ ELECTRICAL/HVAC WORK FOR 5 SUB REGISTRAR OFFICES (ANAND, DHOLKA, KAPADVANJ, MAHUDHA, MANDAL)

Sr. No. Description Quantity Unit Rate Amount

Removing/Shifting existing TW partitions/Panelling/Curtain/Furniture including

hardware/Civil/Sanitary/Piping Work etc including stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift and the site shall be cleaned as directed by EIC. Care shall

be taken to remove the partition / door so as to reuse the same.

Removing Ac,OutDoor & Accessories and Handover the Client as per Architect/Grimco Manager

Instruction. Care shall be taken to remove the AC so as to reuse the same.

CHIPPING CONCRETE WORK :Chipping of unsound weak concrete material from slab, beam, column

and around the reinforcement incl. plaster etc. with manual chiselling with standard power driven

percussion type of pneumatic chisel of standard make as directed by Eng. In Charge incl. tapering all

edges and making square shoulders of cavities etc. comp. and disposal of debris outside the premises

incl. cleaning of exposed reinforcement using approved alkaline chemical rust remover (doctor fix it

rust remover or its equivalent chemical comp. as per manufacturers specification) (Area of RCC surface

is to be measured for payment) etc. incl applying 10 to 15 mm avg. thick plaster in C.M. (1:3) incl.

curing, scaffolding, curing, Existing Removing & Scrape Plaster etc. comp. as directed by Grimco

Manager /Architect.

MASONARY WORK: Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement :4 -coarse sand) in

(Conventional) Rate Shall Be Consider All Floor & Work Shall be Execute as per Architect

Grimco Manager Instruction.

Providing Brick masonary using common burnt clay building bricks for foundation and plinth

having crushing strength not less than 35 kg./ Sq. Cm. in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) incl. watering,curing,scaffolding and racking out joints etc. comp as per directed by

PLASTER WORK : Providing 15mm thik. Cement plaster in single coat on Internal Walls for interior

6 plastering of following finished even and smooth in Cement Mortar 1:3 (1-Cement : 3-Sand) incl. 27.00 SQMT 203.34

finishing with a floating coat of neat cement slurry.

FLOORING: Providing and Laying Glossy/mat Finished vitrified tiles of size 800 X 800mm and 8 mm to

10mm thick of approved make and colour having homogeneous materials in flooring laid on 20mm

thick average cement mortar 1:3 (1 cement: 3 coarse sand)as directed by Engineer in charge. Applying

spacer of 4mm and not less than 2mm depth of epoxy grooving of lavicrete , Roff equivalents directed

by Engineer in charge. incl. cost of fixing materials, labour, tools, plants, equipotent incl. all lead & lift

Supplying & fixing heavy duty 800 X 800 mm Vitrified tiles of 8 to 9 mm the of Approved Brand in

Skirting as per approved pattern ,Match Shade with Existing Flooring & design laid over neat cement

slurry & cement mortar in (1:6) bedding 20 mm the average & joint with colour cement slurry incl.

special cornices, corners or angles, tiles etc. incl.Applying spacer of 4mm and not less than 2mm depth

of epoxy grooving of lavicrete , Roff equivalentas directed by Engineer in charge. incl. cost of fixing

materials,labour, tools, plants, equiptnent incl. all lead & lift comp, labour, tools, plants, equipmens

incl. all lead & lift comp. as directed by Architect /EIC .

Removing & Refixing Grill as per Architect /Grimco Manager Instruction Rate Shall be Including

9 Loading,Unloading,Labour,Welding,Hardware etc.Care shall be taken to remove the Grill so as to reuse 2.00 EACH 500.00

Providing & Fixing window having extruded aluminium colour anodized section frame main outer size

63.5 x38.1x1.95mm(Jindal or Hindalco section No.4605 @ Wt.1.094 Kg/Rmt) horizontal Two Track

member size 61.85x31.75x1.2mm(of Jindal or Hindalco section No.8687 @ Wt.of 0.695 Kg/mt.) vertical

member of size 61.85x 31.75x1.3mm (of Jindal or Hindalco section No. 8758 @ wt of 0.659 Kg/Mt.)

with Sluiding shutter of horizontal member size 40x18x1.29mm (of Jindal or Hindalco section No.

@ wt.of 0.456 kg/mt.) vertical member of size 40x18x1.29mm (of jindal or Hindalco section No.8947 @

wt.of 0.456 Kg/ mt./section 8948 @ wt of 0.457 kg/mt.) with 5mm thick transperant bronze colour

tinted float glass with colour anodized aluminium fittings & fixtures with transparent silicon sealant

glass fixing to frame as per detail .

applying primer coat of the paint, Putty shall be applying walls and ceiling for making even surface up

to finish level.Providing and applying even coats of acrylic emulsion paint / on walls and ceiling up to

final finish. Shade and texture of the paint shall be as approved by Architect or EIC. Application of

paint shall be with brush and last coat of paint shall be applied with a standard company roller all as

approved by architect/Grimco Manager.rates are inclusive cost of paint, putty, primer, brush,

roller,Removing Existing Paint, scaffolding cleaning charges etc. complete.

Providing and applying synthetic enamel paint (and Repair Grill/M.s. as per Site Situation-Proper

Finishing , Levelling,Welding, Cleaning) of Asian/Nerolac/ICI/Lewis Berger/J&N of approved brand to

12 previously painted steel work with one coat of approved quality and brand paint of Asian, Nerolac, ICI, 36.00 SQMT 250.00

Berger, Johnson make and of required shade, including cleaning and scrapping the surface with sand

paper etc. complete as directed.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

FALSE FLOORING (Stage) Providing & Fixing ms Structure Vertical Stand 50X50X5 mm 600 X 1200 mm

center to Center Distance with Anticorrosive Paint and above Stand 25 X 25X5 mm square Hollow Pipe

13 With Anticorrissive Paint by Steel Welded Construction. Outer All Exposed Part Shall be Fitted Square 8.00 SQMT 7000.00

Hollow Pipe & 18 mm Plywood With Laminate with Adhesive Material , Nail Scrue Abro tap Etc all

Required Hardware.

FULL HEIGHT /LOW HEIGHT PARTITION (FULLY SOLID) (75mm thk.) Providing and fixing full height / half

height double skin wooden partition upto ceiling or beam bottom as per drawing and framing in

Alluminium with both side cover with 12mm thick comm. ply finished both Side with 1.0mm thick

selected laminate, without any air gap and grooving as per design& instruction of the EIC/Architect.

14 wooden framing to be erected above false ceiling make hole/face plate for conduit pipes of electrical / 146.00 SQMT 5200.00

networking cables with openable stud from partition Including all materials and labour etc. Open

edges also finish with laminate. complete as per detail drawing and instruction of Architect/engineer-

Providing and fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and fixing full

height glass partition made out of glazed partition with stanless steel U channel profile in the top and

Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The glass to be

butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between two butt

15 jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled with 18.00 SQMT 4800.00

clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

Providing and fixing 35 mm thick Decorative type Water proof flush door shutters, solid core

construction with wood frame with Polish of ground class hard-wood with cross band and face ply-

wood face panels, 1.0 mm thick laminate on both sides including the top Portion ( Aprox 0.380mm

Height ) Pack With Transperent Glass With Ply Frame, Stainless steel fixtures and fastening like

,Handle,Lock , stopper including for door shutters sides etc complete. as directed by engineer in

Door Laminate Change. To be Removed & Refixing .Providing and Fixing Both Side 1 mm laminate &

Existing Removing Laminate Door of washable type material of good quality with appropriate

adhesive of approved quality like fevicol or its equivalent brands with smooth finishing and in line

level with regular edges as per requirement and site situation incl. cutting and any necessary cut outs

of Glass and Cutout Finish With Plywood With Selected Laminate & Door if any required etc. comp. in

all respects. All rates are inclusive of hardware like, nails, screws, abro taps, adhesive etc. complete.

Providing ,Removing Existing Door Closer and fixing Door Closer and Blue Space GPRH Solid Standoffs

18 Heavy-Duty Commercial Grade-304 Stainless Steel Push Pull Door Handle as per Architect & EIC 6.00 EACH 2500.00

Instruction. Rate Shall be Including Fitting Charge.

Table (1.95 x 0.750 x 0.75) Providing and fixing the Table with top of 19 mm thick BWR plywood&

Table Top Side Boarder added 19 mm Plywood in Below Side with post formed approved laminate The

side leg should be made of Wood box with laminate. CPU box with made of 18mm. thick plywood and

1mm. thick laminate on all exposed side.The apron should be made of 18mm. thick plywood and for

elevation 18mm. thick one side BWR ..Plywood patta as shown in drawing and finished with 1mm.

thick laminate. Footrest (0.60 x 0.38) should be made from 18mm. BWR plywood with 1mm laminated

finish in the approved shade. Including all materials and labour etc. complete as per detailed drawing

and instructions of engineer-in-charge.

19 Side Table (1.225x 0.45 x 0.75) Providing and fixing Side Table for 25mm thick (BWR board,) post 3.00 EACH 22500.00

forming laminated top with 6mm thick BWR plywood at backside finished with 1mm. thick approved

laminate, made out of 18mm thick BWR plywood with exterior side 1mm. and interior side 0.6mm.

Approved laminate. Drawer unit box (measurement shown in drawing) with wooden bedding

patti/PVC, lock and telescopic channel. Key board tray will be made of 18mm. thick post foamed BWR

plywood with telescopic chanel. Shutter will be made of 18mm. thick post forming BWR with magnet,

multiple drawer lock, S.S. legs (75mm height) in bottom, auto hinges of HAFELE or equivalent.

Including all materials and labour etc. complete as per detailed drawing and instructions of engineer-

Linear / Running Counter For Work Station.Providing and Fixing Linear / Running Counters of 4' Wide

width 2' made up of 18 mm thick Plywood. The table top shall be finished with 1 mm thick laminate of

approved make and the edge shall be finished with 12 mm wooden bidding duly finished in polish /

duco paint to match with the laminate of the table top. Providing & Supplying Work Station Between

Glass Partition Soft Board.The table shall be provided with drawer pedestal unit made up of 18 mm

thick MR ply and drawers shall be running on approved make EBCO / Hettich / Haffele make telescopic

channels. The handle lock etc. shall be of the similar make. The workstation also shall be provided with

each of key board tray, CPU trolley and foot rest of EBCO / Innofitt make as per the instructions of

Engineer-in-charge / Architects.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Low Height/ Full Height Storage - Providing, Supplying & Fixing Basic Str. in 19 mm Ply wood, Outer

Side 1 mm Laminate in position for Storage and Inner 0.5 yo 0.6 mm Laminate of washable type

material of good quality with appropriate adhesive of approved quality like fevicol or its equivalent

21 brands with smooth finishing and in line level with regular edges as per Arch./ EIC Instruction incl. 13.00 SQMT 9000.00

cutting and any necessary cut outs of Storage & Door if any required etc comp. in all respects. All rates

are inclusive of hardware like, nails, screws,abro taps, Lock , Handle , Auto hinge , adhesive etc.

GLASS DOOR: Providing and fixing in position full height 12mm thick toughened glass STL45 Door

System with 6063-T6 grade duly Anodized Aluminium Sections having sizes of 45x55x1.5mm thick,

mm Toughened Glass including Assa Abloy Door Closure /Floor Spring , Hinges, SS Handle (H Type

450mm), SS Bottom Lock, Thermoplastic Gaskets & Screw Caps all necessary hardware of as per

22 approved make by Architect. 10mm thick Saint Gobain make customized clear toughened glass.Work 18 SQMT 5880.00

complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, all

leads ,accessories, sample mockup, all floor , all levels, all heights , necessary frame work,Scafffolding

etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

MANAGER CABIN MAIN CHAIR Adj. Arms Larger Seats seat size: 47.0 cm. (w) x 51.5 cm. (d) back size

:45.0 cm. (w) x 65.3 cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should be

moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. armrests : the

armrests have an up-down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure.

armrest top has an integrated layer of thermoplastic elastomer (tpe).

lumbar support assembly: the lumbar support consshould be ts of polypropylene pad with moulded

polyurethane foam & covered with polyester fabric. the height of lumbar pad can be adjusted through

two projecting knobs provided on the rear side of the pad. lumbar pad has an adjustment of 8.0 ±

front pivot synchro mechanism: the adjustable tilting mechanism should be designed with the

following features.

23 • 360° revolving type. 3 EACH 15000.00

• single point control.

• front-pivot for tilt with feet resting on ground ensuring more comfort.

• tilt tension adjustment.

• 4-position locking with anti-shock feature.

• seat/back tilting ratio of 1:2.

pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ±

pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted

with 5 nos. twin wheel castors. the pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm.

with castors).twin wheel castors: the twin wheel castors should be injection moulded in black

nylon.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE:

Staff Chair the seat should be made up of 1.2 ±0.1cm. thick hot-pressed

plywood , upholstered with fabric upholstery covers and moulded polyurethane foam.

seat size: 47.0 cm. (w) x 48.0 cm. (d)back : the back asembly. should be made of powder coated (oft 40-

60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with

contoured lumbar support for extra comfort. the back should be upholstered using double layer

spacer mesh fabric with high tenacity yarn.

back size : 46.5 cm (w) x 60.5 cm (h)high resilience (hr) polyurethane foam: the hr polyurethane foam

should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25%

compression.armrests: the one-piece armrests should be injection moulded from black co-polymer

polypropylene. Centre-tilt mechanism: the mechashould be m should be designed with the following

24 • 360° revolving type. 25 EACH 8700.00

• 17° ±2° maximum tilt on pivot at centre

• upright position locking.

tilt tension adjustment. .pneumatic height adjustment: the pneumatic height adjustment has an

adjustment stroke of 11.0 ±0.3cm.elescopic bellow assy: the bellow should be 3 piece telescopic type

and injection moulded in black polypropylene.pedestal .: the pedestal should be injection moulded in

black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be

±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)twin wheel castors: the twin wheel castors should

be injection moulded in black nylon.Overall Dimensions of Chair-Seat Height - min 43.3 to max

Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm

and Depth-76.3 cm.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

25 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 19000.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts.

Providing & Fixing Cushionon Seating & Back as per Instruction. The Shell to be assembled on the cross

beam with help of M8 Bolts.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

26 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 7 EACH 17500.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

GYPSUM BOARD CELLING : Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender

channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making

necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

595 x 595 MM CELLING:Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light

weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 1200X600mm and secondary

28 cross ’T’ of length 600mm and size600mm centre to centre to form agrid of 24x28mm made of 0.30 157 SQMT 1632.63

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre

to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges

light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the

grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to

centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyester

baked paint, for all heights, as per specifications, drawings and as directed by engineer-incharge. Note:-

Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made

SS plate Signage: 450mm X 100mm - Stainless Steel satin finished flat etching plate of 1.5mm thick.

Providing Making and fixing of various in-door signage, as & where basis. sign in ISI Brushed S.S. Grade

304 letters in English letter + All text and design in acid process, each plates. Each text & design with

respective color coated complete plate. The SS mounted on glass or any non holes surfaced by 3M

29 double sided tape with required chemical process, guidelines by 3M company. Whereas, Any other 8 EACH 1800.00

then glass surface, SS plate mounted by Two side screws with required grips nd holes on the wall with

two SS spacer screws. The item should be as per instruction at site approved by Architect of Engineer

in charge. The rate shall be inclusive of scaffolding, drilling, adhesive material etc. at all height.

Providing & Arranging wheel chair for physically handicapped person having dimension 790(L) x

600(W) x 700(H)mm. With foldable frame structure made of carbon steel setcion 22mm x 1.2mm or as

per direction of engineer in charge. A3 carbon sheet with chrome finish cross bars made of A3 carbon

steel material with setcion 25.4mm x 1.2mm., 24 inch solid mag wheels with alloy in the rim, hand rim

of setcion 16mm x 1.2mm. carbon steel with chrome finish, front wheel of 8 inch HUB made of PA

30 polymer & outer side of solid rubber PU moulded arm rest & base made of ABS, leather finish calf rest 1 EACH 13570.00

& seat with cushion alluminium foot rest with updown movement having extended base foot press

with moulded plastic including hand brakes & full structure is anti rust chrome finish with users

capacity of 100 kg including all necessary fixture, fastners, fittings, labour, material, machinary etc.

complete as seletced and diretced by Engineer-in-charge.

Providing & fixing S.S. Pipe railing of 50mm dia pipe not less than 18guage, in 3 rows supported by S.S.

Pipe of 50mm dia at every corners & 1.5 mt C/C incl. concrete block (0.35 X 0.35 X 0.35) incl. 16 guage

S.S. sheet using required cutting, jointing, welding, threading, drilling & fixing etc. comp. as directed as

per drawing (For Platform)

Providing & Fixing Shelf Adhesive Tractile Tiles as per Architect/ GRIMCO manager Instruction. The

Tiles shall be Fixed with Suitable Adhesive Material with All required Additional Hardware Suppot.

Rate shall be Including Transportation , All Floor , Hardware, Adhesive Material etc.

Fixing Ipsa Super Strong Handsfree Foot Operated Pull (304 s.s)door latches of sizes 100mm with

necessary screws etc. complete

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Painting lines, dashes, arrows, letters etc on roads, Air- fields and like in two coats with road marking

paint, brushing including cleaning the surface of all dirt, dust and other foreign matter (ii) over

Providing and fixing required size Stainless steel plate of 1.0mm thickness with regular

printed signage at top in black colour at top part of plate and respective brialle lipi

sgnages at bottom part the plate, S.S. Plate to be fixed on 10mm thick clear acrylic

sheet, this whole assembly to be fixed on wall with four numbers of SS studs etc

complete as per instructions of engineer in-charge.

DEDO WORK (600X600 mm):'Providing & laying Antiskid Vitrified 12mm thick tiles flooring, treads of

steps and landing laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface and jointed with colour cement slurry including finished with flush pointing &

cleaning the surface etc. completed of any Shade and approved by Higher Authority of approved

brands & Size. Providing & Applying spacer of 5mm and not less than 4mm depth of epoxy grooving of

levirate , Ruff equivalents as per detailed drawing and as directed by Grimco Manager /Architect. Basic

Cost of Tiles is Rs 50/-sqft

Scraping of old paint/ distemper wherever necessary from the existing walls, and applying of 4.0 to

37 mm thick lime over it to give a smooth leveled finish, the final coat to have one coat of oil based 527.00 SQMT 255.00

Cement primer the cost shall include all labor , materials, etc complete.

Providing & fixing 18mm thick cement sheet/18 mm Plywood for panelling work with Selected Colour

as per approved by Architect/Client. The rate shall be for all floors, at all heights, all shapes including

CNC / Engraving and all costs.

The frame work shall be made from square hollow aluminum anodized section size of 50x50x1.5 mm

& 25x50x1.5 mm of approved make conforming to IS code. The framework shall be fixed as per

drawing vertically @ 600 mm c/c & horizontal 600 mm c/c horizontally. which shall be provided from

gr. level to RCC slab / beams soffit level. Rates shall also be inclusive of cost of making CNC/engraving

/cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing

38 additional sections for strengthening around the openings/cutouts additional support for fixing of 8.00 SQMT 4500.00

patch fittings for doors, making grooves between wall & board, in filled with termite treated members

if required or as per drawing /instruction of EIC. All curved surfaces, recesses, waffles shall be part of

the paneling including Openable shutter wherever required area and finished with the same material.

Work complete including all type of material, fittings , fixtures, Finish, loading , unloading

transportation, all leads ,accessories, groove, adhesive ,tape, headless nails, sample mockup, all floor

all levels, all heights etc complete as per detailed drawings ,specifications & instruction of

Client/EIC.sample mock shall be approved from as per Architect/GRIMCO Manager &instruction.

Providing and fixing wooden Palmet of up to 50 to 150 mm Thick L shape made & 300 mm Height of

12mm thick ply with 4 mm thick mdf with colour as per IS 710 and beading of 4mm thick and 25mm

wide Ghana Teak wood for projection screen. Rates shall also be inclusive of cost of making

CNC/engraving /cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers

etc & providing additional sections for strengthening around the openings/cutouts additional support

for fixing of patch fittings for doors, making grooves between wall & board, in filled with termite

treated members if required or as per drawing /instruction of EIC. Rate to be inclusive of lipping,

cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and

for all floors as per drawing and approved sample etc should also take load of all the all roller blinds

as per Architect/GRIMCO Manager instruction.

Providing wood work in frames of Doors, windows cleare story windows and other similar works

wrought,frame and fixed in position including both Side 100 mm wide Panelling with Selected

Laminate. Providing & Fixing 12 mm Thick Plywood With Selected Laminate for Panelling . Rate Shall

be including Anodized aluminum fixtures & fastenings ,Adhesive Material ,& Necessary Hardware. the

Measurement shall be Consider Running Length X Width as directed by engineer in charge.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Providing & Fixing Wooden Partition with 10 mm Glass framing in Alluminium with both side cover

with 12mm thick comm. ply finished both Side with 1.0mm thick selected laminate, without any air

gap and grooving as per design& instruction of the EIC/Architect. wooden framing to be erected

above false ceiling make hole/face plate for conduit pipes of electrical / networking cables with

openable stud from partition Including all materials and labour etc. Open edges also finish with

laminate.Providing & Fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and

fixing full height glass partition made out of glazed partition with stanless steel U channel profile in the

top and Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The

glass to be butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between

two butt jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled

with clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

supplying & fixing 3m sparkle film/Fluted Film on glass with manufacturer specification, as per the

42 detailed technical specifications, drawings and as per Architect/GRIMCO Manager instruction. 36.00 SQMT 1200.00

Deep Cleaning Glass, Wall,Window ,Table with Require Material Broom,Dust Pan,Squeegee,Sprey

Cleaner,Mop as per Instruction of the Grimco Manager/Architect.

Providing and fixing Roller Blind fixed on window level on wooden batten and curtain lift with cotton

thin rope, design and colour as per instruction by engineer – in – Charge with necessary hardware

fitting, material and labour etc. complete as per detail drawing and instruction of engineer-in charge

and consultant.

Providing and fixing ACP Letters for Office Detail Name & addres Letters on ACP

fascia.Providing 3mm thick alluminium composite panel (ACP) sheet fascia and all side with

required iron angle / hollow heavy pipe structure frame. and back side cover up by aliminium

sheet ,complete box should be water-proof.and make it . Approx size of the Signages is

:5'X2'0"X0'5".Outdoor signage: 5 to 6 mm thick & ACP Letters / logo signage Complete as per

EIC/Architect Instruction.

Providing and Fixing Doormat (6' X 2') made up of synthetic material as per the approval from the

Architect / EIC.

Providing and Fixing Doormat ( Approx 1.5' X 2') made up of synthetic material as per the approval

from the Architect / EIC.

Providig & Fixing Wall Clock as per approved make. As per instruction at site approved by Architect of

Engineer in charge.

Providing, supplying SS 304 perforated Dustbin/ Wire mesh Dustbin as per approved make. As per

instruction at site approved by Architect of Engineer in charge.

Supplying labour for removing and filling all type Civil /Electrical HVAC of Debric incl. construction

50 waste materials and cleaning or any other type work for 8 hr. per day comp. as directed by eng. 10.00 EACH 1650.00

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with

51 textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with 48.00 Pt. 445.00

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single

52 mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / 25.00 Pt. 632.00

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type

53 of accessories. 22.00 Pt. 471.00

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling completeCat-III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type accessories. Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(9) 16 Amp. SP one way switch Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green)

both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below

type of pipe with 6A Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

57 modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or 5.00 Pt. 562.00

ceiling rose or H.D.Connector as directed.ss will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be

erected complete with earth continuity and necessary connection with primary light with accessories

erected on Metal / PVC / wooden box covered covered with appropriate front plate modules erected

on / in wall / ceiling for open / concealed wiring. with necessary Lamp holder / ceiling rose /

58 H.D.Connector as directed.as per pipe erected with following type of accessories.Note:- Maximum up 50.00 Pt. 166.00

to 6 mtrs length, excess will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories cat iii

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat-III

(4) TV Co-axial Socket outlet

(7) Blank Plate Single

(8) Modem Jack for Computer Open RJ-45

64 (19) Modular Indicating Call Bell Cat.III 1.00 EA 326.00

65 (20) Modular Buzzer Cat.III 1.00 EA 148.00

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

66 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 550.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

69 Check-nuts etc. complete of following sizes. 210.00 Mtr. 17.00

Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement

with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin

71 polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall / ceiling of following size . 105.00 Mtr. 31.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS with necessary end caps Internal and

72 external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following sizes 95.00 Mtr. 187.00

(3) 50 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

73 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 515.00 Mtr. 101.00

(a) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size

(a) 2 wire 4 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly -

75 Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. 290.00 Mtr. 39.00

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE

insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR

outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following

size of conductors & nos.of pairs. With necessary connections.

A. Conductor Size 0.5 mm

(a) (2) Unarmoured

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing & erecting main Distribution (MDF) indoor type, back mounted frame

(a) Suitable for 10 pair

ARMOURED ALLUMINIUM CABLES.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

79 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 20.00 Mtr. 152.00

d) 4 Core 16 Sq.mm.

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

81 armoured cable complete with out going tails, insulating tape etc for following size of cables. 4.00 Nos 38.00

(C) 2 to 4 core 10 Sq. mm

82 d) 2 to 4 Core 16 Sq.mm 4.00 Nos 47.00

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly

83 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut 16.00 Nos 13.00

bolts in an approved manner.

Providing and fixing printed instruction chart both in English and Gujarati and duly framed with front

85 glasses, for treatment of person suffering from Electric shock with minimum 50" diagonally size. 2.00 Nos 129.00

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

86 clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. 4.00 Ea 6526.00

[A] For 4.5 Kg Capacity

MINIATURE CIRCUIT BREAKERS.

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having

87 breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 20.00 Nos 111.00

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking

88 capacity & confirms to IS : 8828 in existing box having following capacity 2.00 Nos 276.00

(A) 6 to 32 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breaking

89 capacity & confirms to IS :8828 in existing box having following capacity 4.00 Nos 632.00

(b)40 Amp. Cat.III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

90 be used) 2.00 Nos 2885.00

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door

EARTH LEAKAGE CIRCUIT BREAKERS.

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz.

91 having characteristic of quick action & tripping with all advance feature & do not incorporate any 6.00 Nos 2213.00

electronic component. for following Max. rating erected as directed

(ii) 40Amps. DP

CEILING FANS AND ACCESSORIS.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI

92 mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium 25.00 Nos 1929.00

blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in

FAN ACCESSORIES.

93 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly 1.00 Mtr. 107.00

painted for fan complete with necessary 24/ O.2, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Roundbar grouted in RCC slab with Making the site as

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

95 length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected 1.00 Nos 107.00

concealed in Ceiling with necessary finishing..

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with

necessary hook of 10 mm M.S. Round Bar.

97 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 1.00 Nos 18.00

TABLE FANS, EXHAUST FANS & ACCESSORIES.

98 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 1.00 Nos 1687.00

RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

99 Luminaire efficiency> 85 lumens/watt , 2.00 Nos 370.00

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)

(A) Tube Light with integral/ non-integral driver

(d) 22-24 Watts, Surge - 4KV,IP-20, 4 feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaire efficiency> 85 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)Square/ Circular Surface/Recessed Mounted

Downlight/Hanging with provision for spring loaded mounting clips complete.(b)16-20 watts, Surge-4

101 Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ 2.00 Kg. 77.00

Transformer LT panel board, Motors etc. using proper clamp.

102 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 2.00 kg 787.00

Removing all Electrical Material / equipment from existing set up , also handover to client

representative as per them requirement

104 Re use the electrical material as per Client's epresentative / architect team 's instruction 1.00 job 5000.00

Supplying and erecting Of 43 " UHD LED display for CCTV monitoring and checking .(the scope

includw the stand and other necessary accessasory to coplete the job .

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE ANAND.

Sr. No. Description Quantity Unit Rate Amount

Supplying & Erecting floor mounted/ table top single phase 50Hz water dispenser with SS 304 food

grade cold tank specification having three water tap of hot/cold/ambient water function, LED display

106 with storage capacity from 2.5 Ltrs to 3.2 Ltrs, cooling capacity 2.5ltrs/hr, including refrigerant with 1.00 Ea. 11443.00

20ltrs refrigerant storage capacity compartment inclusive 1No.water topping bottle

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

107 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 200.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

(8) Modem Jack for Computer Open RJ-45

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

110 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 2.00 no 47780.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.

(B) for 1.5 ton capacity - Premium Cat.

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with

accessories etc. duly connected separately erected evaporating unit and blower motor with its

accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star

and above of current year) with necessary core cutting.for 2 ton capacity

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

112 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 3.00 no 37983.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.[A] For 1 Ton Capacity Premium Cat.

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR

capacity erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and

control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Providing & Fixing 100X100 mm PVC Casing Patti for Drain Pipe/Electrical as per Architect/Grimco

Manager Instruction.

Misc.Civil Work Like Wall Jury,Cut Out & Opening to pass Piping Tray,wire ,pipes & Drain Pipes

116 Including with Refinishing & Plastering of the Same to the Original Finish. 1.00 JOB WORK 9500.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Removing/Shifting existing TW partitions/Panelling/Curtain/Furniture including

hardware/Civil/Sanitary/Piping Work etc including stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift and the site shall be cleaned as directed by EIC. Care shall

be taken to remove the partition / door so as to reuse the same.

Removing Ac,OutDoor & Accessories and Handover the Client as per Architect/Grimco Manager

Instruction. Care shall be taken to remove the AC so as to reuse the same.

CHIPPING CONCRETE WORK :Chipping of unsound weak concrete material from slab, beam, column

and around the reinforcement incl. plaster etc. with manual chiselling with standard power driven

percussion type of pneumatic chisel of standard make as directed by Eng. In Charge incl. tapering all

edges and making square shoulders of cavities etc. comp. and disposal of debris outside the premises

incl. cleaning of exposed reinforcement using approved alkaline chemical rust remover (doctor fix it

rust remover or its equivalent chemical comp. as per manufacturers specification) (Area of RCC surface

is to be measured for payment) etc. incl applying 10 to 15 mm avg. thick plaster in C.M. (1:3) incl.

curing, scaffolding, curing, Existing Removing & Scrape Plaster etc. comp. as directed by Grimco

Manager /Architect.

MASONARY WORK: Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement :4 -coarse sand) in

(Conventional) Rate Shall Be Consider All Floor & Work Shall be Execute as per Architect

Grimco Manager Instruction.

Providing Brick masonary using common burnt clay building bricks for foundation and plinth

having crushing strength not less than 35 kg./ Sq. Cm. in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) incl. watering,curing,scaffolding and racking out joints etc. comp as per directed by

PLASTER WORK : Providing 15mm thik. Cement plaster in single coat on Internal Walls for interior

6 plastering of following finished even and smooth in Cement Mortar 1:3 (1-Cement : 3-Sand) incl. 7.00 SQMT 203.34

finishing with a floating coat of neat cement slurry.

FLOORING: Providing and Laying Glossy/mat Finished vitrified tiles of size 800 X 800mm and 8 mm to

10mm thick of approved make and colour having homogeneous materials in flooring laid on 20mm

thick average cement mortar 1:3 (1 cement: 3 coarse sand)as directed by Engineer in charge. Applying

spacer of 4mm and not less than 2mm depth of epoxy grooving of lavicrete , Roff equivalents directed

by Engineer in charge. incl. cost of fixing materials, labour, tools, plants, equipotent incl. all lead & lift

Supplying & fixing heavy duty 800 X 800 mm Vitrified tiles of 8 to 9 mm the of Approved Brand in

Skirting as per approved pattern ,Match Shade with Existing Flooring & design laid over neat cement

slurry & cement mortar in (1:6) bedding 20 mm the average & joint with colour cement slurry incl.

special cornices, corners or angles, tiles etc. incl.Applying spacer of 4mm and not less than 2mm depth

of epoxy grooving of lavicrete , Roff equivalentas directed by Engineer in charge. incl. cost of fixing

materials,labour, tools, plants, equiptnent incl. all lead & lift comp, labour, tools, plants, equipmens

incl. all lead & lift comp. as directed by Architect /EIC .

Removing & Refixing Grill as per Architect /Grimco Manager Instruction Rate Shall be Including

9 Loading,Unloading,Labour,Welding,Hardware etc.Care shall be taken to remove the Grill so as to reuse 8.00 EACH 500.00

Providing & Fixing window having extruded aluminium colour anodized section frame main outer size

63.5 x38.1x1.95mm(Jindal or Hindalco section No.4605 @ Wt.1.094 Kg/Rmt) horizontal Two Track

member size 61.85x31.75x1.2mm(of Jindal or Hindalco section No.8687 @ Wt.of 0.695 Kg/mt.) vertical

member of size 61.85x 31.75x1.3mm (of Jindal or Hindalco section No. 8758 @ wt of 0.659 Kg/Mt.)

with Sluiding shutter of horizontal member size 40x18x1.29mm (of Jindal or Hindalco section No.

@ wt.of 0.456 kg/mt.) vertical member of size 40x18x1.29mm (of jindal or Hindalco section No.8947 @

wt.of 0.456 Kg/ mt./section 8948 @ wt of 0.457 kg/mt.) with 5mm thick transperant bronze colour

tinted float glass with colour anodized aluminium fittings & fixtures with transparent silicon sealant

glass fixing to frame as per detail .

applying primer coat of the paint, Putty shall be applying walls and ceiling for making even surface up

to finish level.Providing and applying even coats of acrylic emulsion paint / on walls and ceiling up to

final finish. Shade and texture of the paint shall be as approved by Architect or EIC. Application of

paint shall be with brush and last coat of paint shall be applied with a standard company roller all as

approved by architect/Grimco Manager.rates are inclusive cost of paint, putty, primer, brush,

roller,Removing Existing Paint, scaffolding cleaning charges etc. complete.

Providing and applying synthetic enamel paint (and Repair Grill/M.s. as per Site Situation-Proper

Finishing , Levelling,Welding, Cleaning) of Asian/Nerolac/ICI/Lewis Berger/J&N of approved brand to

12 previously painted steel work with one coat of approved quality and brand paint of Asian, Nerolac, ICI, 71.00 SQMT 250.00

Berger, Johnson make and of required shade, including cleaning and scrapping the surface with sand

paper etc. complete as directed.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

FALSE FLOORING (Stage) Providing & Fixing ms Structure Vertical Stand 50X50X5 mm 600 X 1200 mm

center to Center Distance with Anticorrosive Paint and above Stand 25 X 25X5 mm square Hollow Pipe

13 With Anticorrissive Paint by Steel Welded Construction. Outer All Exposed Part Shall be Fitted Square 7.00 SQMT 7000.00

Hollow Pipe & 18 mm Plywood With Laminate with Adhesive Material , Nail Scrue Abro tap Etc all

Required Hardware.

FULL HEIGHT /LOW HEIGHT PARTITION (FULLY SOLID) (75mm thk.) Providing and fixing full height / half

height double skin wooden partition upto ceiling or beam bottom as per drawing and framing in

Alluminium with both side cover with 12mm thick comm. ply finished both Side with 1.0mm thick

selected laminate, without any air gap and grooving as per design& instruction of the EIC/Architect.

wooden framing to be erected above false ceiling make hole/face plate for conduit pipes of electrical /

networking cables with openable stud from partition Including all materials and labour etc. Open

edges also finish with laminate. complete as per detail drawing and instruction of Architect/engineer-

Providing and fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and fixing full

height glass partition made out of glazed partition with stanless steel U channel profile in the top and

Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The glass to be

butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between two butt

15 jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled with 17.00 SQMT 4800.00

clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

Providing and fixing 35 mm thick Decorative type Water proof flush door shutters, solid core

construction with wood frame with Polish of ground class hard-wood with cross band and face ply-

wood face panels, 1.0 mm thick laminate on both sides including the top Portion ( Aprox 0.380mm

Height ) Pack With Transperent Glass With Ply Frame, Stainless steel fixtures and fastening like

,Handle,Lock , stopper including for door shutters sides etc complete. as directed by engineer in

Door Laminate Change. To be Removed & Refixing .Providing and Fixing Both Side 1 mm laminate &

Existing Removing Laminate Door of washable type material of good quality with appropriate

adhesive of approved quality like fevicol or its equivalent brands with smooth finishing and in line

level with regular edges as per requirement and site situation incl. cutting and any necessary cut outs

of Glass and Cutout Finish With Plywood With Selected Laminate & Door if any required etc. comp. in

all respects. All rates are inclusive of hardware like, nails, screws, abro taps, adhesive etc. complete.

Providing ,Removing Existing Door Closer and fixing Door Closer and Blue Space GPRH Solid Standoffs

18 Heavy-Duty Commercial Grade-304 Stainless Steel Push Pull Door Handle as per Architect & EIC 1.00 EACH 2500.00

Instruction. Rate Shall be Including Fitting Charge.

Table (1.95 x 0.750 x 0.75) Providing and fixing the Table with top of 19 mm thick BWR plywood&

Table Top Side Boarder added 19 mm Plywood in Below Side with post formed approved laminate The

side leg should be made of Wood box with laminate. CPU box with made of 18mm. thick plywood and

1mm. thick laminate on all exposed side.The apron should be made of 18mm. thick plywood and for

elevation 18mm. thick one side BWR ..Plywood patta as shown in drawing and finished with 1mm.

thick laminate. Footrest (0.60 x 0.38) should be made from 18mm. BWR plywood with 1mm laminated

finish in the approved shade. Including all materials and labour etc. complete as per detailed drawing

and instructions of engineer-in-charge.

19 Side Table (1.225x 0.45 x 0.75) Providing and fixing Side Table for 25mm thick (BWR board,) post 2.00 EACH 22500.00

forming laminated top with 6mm thick BWR plywood at backside finished with 1mm. thick approved

laminate, made out of 18mm thick BWR plywood with exterior side 1mm. and interior side 0.6mm.

Approved laminate. Drawer unit box (measurement shown in drawing) with wooden bedding

patti/PVC, lock and telescopic channel. Key board tray will be made of 18mm. thick post foamed BWR

plywood with telescopic chanel. Shutter will be made of 18mm. thick post forming BWR with magnet,

multiple drawer lock, S.S. legs (75mm height) in bottom, auto hinges of HAFELE or equivalent.

Including all materials and labour etc. complete as per detailed drawing and instructions of engineer-

Linear / Running Counter For Work Station.Providing and Fixing Linear / Running Counters of 4' Wide

width 2' made up of 18 mm thick Plywood. The table top shall be finished with 1 mm thick laminate of

approved make and the edge shall be finished with 12 mm wooden bidding duly finished in polish /

duco paint to match with the laminate of the table top. Providing & Supplying Work Station Between

Glass Partition Soft Board.The table shall be provided with drawer pedestal unit made up of 18 mm

thick MR ply and drawers shall be running on approved make EBCO / Hettich / Haffele make telescopic

channels. The handle lock etc. shall be of the similar make. The workstation also shall be provided with

each of key board tray, CPU trolley and foot rest of EBCO / Innofitt make as per the instructions of

Engineer-in-charge / Architects.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Low Height/ Full Height Storage - Providing, Supplying & Fixing Basic Str. in 19 mm Ply wood, Outer

Side 1 mm Laminate in position for Storage and Inner 0.5 yo 0.6 mm Laminate of washable type

material of good quality with appropriate adhesive of approved quality like fevicol or its equivalent

21 brands with smooth finishing and in line level with regular edges as per Arch./ EIC Instruction incl. 7.00 SQMT 9000.00

cutting and any necessary cut outs of Storage & Door if any required etc comp. in all respects. All rates

are inclusive of hardware like, nails, screws,abro taps, Lock , Handle , Auto hinge , adhesive etc.

GLASS DOOR: Providing and fixing in position full height 12mm thick toughened glass STL45 Door

System with 6063-T6 grade duly Anodized Aluminium Sections having sizes of 45x55x1.5mm thick,

mm Toughened Glass including Assa Abloy Door Closure /Floor Spring , Hinges, SS Handle (H Type

450mm), SS Bottom Lock, Thermoplastic Gaskets & Screw Caps all necessary hardware of as per

22 approved make by Architect. 10mm thick Saint Gobain make customized clear toughened glass.Work 8 SQMT 5880.00

complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, all

leads ,accessories, sample mockup, all floor , all levels, all heights , necessary frame work,Scafffolding

etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

MANAGER CABIN MAIN CHAIR Adj. Arms Larger Seats seat size: 47.0 cm. (w) x 51.5 cm. (d) back size

:45.0 cm. (w) x 65.3 cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should be

moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. armrests : the

armrests have an up-down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure.

armrest top has an integrated layer of thermoplastic elastomer (tpe).

lumbar support assembly: the lumbar support consshould be ts of polypropylene pad with moulded

polyurethane foam & covered with polyester fabric. the height of lumbar pad can be adjusted through

two projecting knobs provided on the rear side of the pad. lumbar pad has an adjustment of 8.0 ±

front pivot synchro mechanism: the adjustable tilting mechanism should be designed with the

following features.

23 • 360° revolving type. 2 EACH 15000.00

• single point control.

• front-pivot for tilt with feet resting on ground ensuring more comfort.

• tilt tension adjustment.

• 4-position locking with anti-shock feature.

• seat/back tilting ratio of 1:2.

pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ±

pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted

with 5 nos. twin wheel castors. the pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm.

with castors).twin wheel castors: the twin wheel castors should be injection moulded in black

nylon.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE:

Staff Chair the seat should be made up of 1.2 ±0.1cm. thick hot-pressed

plywood , upholstered with fabric upholstery covers and moulded polyurethane foam.

seat size: 47.0 cm. (w) x 48.0 cm. (d)back : the back asembly. should be made of powder coated (oft 40-

60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with

contoured lumbar support for extra comfort. the back should be upholstered using double layer

spacer mesh fabric with high tenacity yarn.

back size : 46.5 cm (w) x 60.5 cm (h)high resilience (hr) polyurethane foam: the hr polyurethane foam

should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25%

compression.armrests: the one-piece armrests should be injection moulded from black co-polymer

polypropylene. Centre-tilt mechanism: the mechashould be m should be designed with the following

24 • 360° revolving type. 11 EACH 8700.00

• 17° ±2° maximum tilt on pivot at centre

• upright position locking.

tilt tension adjustment. .pneumatic height adjustment: the pneumatic height adjustment has an

adjustment stroke of 11.0 ±0.3cm.elescopic bellow assy: the bellow should be 3 piece telescopic type

and injection moulded in black polypropylene.pedestal .: the pedestal should be injection moulded in

black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be

±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)twin wheel castors: the twin wheel castors should

be injection moulded in black nylon.Overall Dimensions of Chair-Seat Height - min 43.3 to max

Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm

and Depth-76.3 cm.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

25 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 19000.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts.

Providing & Fixing Cushionon Seating & Back as per Instruction. The Shell to be assembled on the cross

beam with help of M8 Bolts.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

26 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 6 EACH 17500.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

GYPSUM BOARD CELLING : Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender

channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making

necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

595 x 595 MM CELLING:Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light

weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 1200X600mm and secondary

28 cross ’T’ of length 600mm and size600mm centre to centre to form agrid of 24x28mm made of 0.30 57 SQMT 1632.63

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre

to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges

light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the

grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to

centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyester

baked paint, for all heights, as per specifications, drawings and as directed by engineer-incharge. Note:-

Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made

SS plate Signage: 450mm X 100mm - Stainless Steel satin finished flat etching plate of 1.5mm thick.

Providing Making and fixing of various in-door signage, as & where basis. sign in ISI Brushed S.S. Grade

304 letters in English letter + All text and design in acid process, each plates. Each text & design with

respective color coated complete plate. The SS mounted on glass or any non holes surfaced by 3M

29 double sided tape with required chemical process, guidelines by 3M company. Whereas, Any other 5 EACH 1800.00

then glass surface, SS plate mounted by Two side screws with required grips nd holes on the wall with

two SS spacer screws. The item should be as per instruction at site approved by Architect of Engineer

in charge. The rate shall be inclusive of scaffolding, drilling, adhesive material etc. at all height.

Providing & Arranging wheel chair for physically handicapped person having dimension 790(L) x

600(W) x 700(H)mm. With foldable frame structure made of carbon steel setcion 22mm x 1.2mm or as

per direction of engineer in charge. A3 carbon sheet with chrome finish cross bars made of A3 carbon

steel material with setcion 25.4mm x 1.2mm., 24 inch solid mag wheels with alloy in the rim, hand rim

of setcion 16mm x 1.2mm. carbon steel with chrome finish, front wheel of 8 inch HUB made of PA

30 polymer & outer side of solid rubber PU moulded arm rest & base made of ABS, leather finish calf rest 1 EACH 13570.00

& seat with cushion alluminium foot rest with updown movement having extended base foot press

with moulded plastic including hand brakes & full structure is anti rust chrome finish with users

capacity of 100 kg including all necessary fixture, fastners, fittings, labour, material, machinary etc.

complete as seletced and diretced by Engineer-in-charge.

Providing & fixing S.S. Pipe railing of 50mm dia pipe not less than 18guage, in 3 rows supported by S.S.

Pipe of 50mm dia at every corners & 1.5 mt C/C incl. concrete block (0.35 X 0.35 X 0.35) incl. 16 guage

S.S. sheet using required cutting, jointing, welding, threading, drilling & fixing etc. comp. as directed as

per drawing (For Platform)

Providing & Fixing Shelf Adhesive Tractile Tiles as per Architect/ GRIMCO manager Instruction. The

Tiles shall be Fixed with Suitable Adhesive Material with All required Additional Hardware Suppot.

Rate shall be Including Transportation , All Floor , Hardware, Adhesive Material etc.

Fixing Ipsa Super Strong Handsfree Foot Operated Pull (304 s.s)door latches of sizes 100mm with

necessary screws etc. complete

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Painting lines, dashes, arrows, letters etc on roads, Air- fields and like in two coats with road marking

paint, brushing including cleaning the surface of all dirt, dust and other foreign matter (ii) over

Providing and fixing required size Stainless steel plate of 1.0mm thickness with regular

printed signage at top in black colour at top part of plate and respective brialle lipi

sgnages at bottom part the plate, S.S. Plate to be fixed on 10mm thick clear acrylic

sheet, this whole assembly to be fixed on wall with four numbers of SS studs etc

complete as per instructions of engineer in-charge.

DEDO WORK (600X600 mm):'Providing & laying Antiskid Vitrified 12mm thick tiles flooring, treads of

steps and landing laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface and jointed with colour cement slurry including finished with flush pointing &

36 cleaning the surface etc. completed of any Shade and approved by Higher Authority of approved 52.00 SQMT 1446.99

brands & Size. Providing & Applying spacer of 5mm and not less than 4mm depth of epoxy grooving of

levirate , Ruff equivalents as per detailed drawing and as directed by Grimco Manager /Architect. Basic

Cost of Tiles is Rs 50/-sqft

Scraping of old paint/ distemper wherever necessary from the existing walls, and applying of 4.0 to

37 mm thick lime over it to give a smooth leveled finish, the final coat to have one coat of oil based 333.00 SQMT 255.00

Cement primer the cost shall include all labor , materials, etc complete.

Providing & fixing 18mm thick cement sheet/18 mm Plywood for panelling work with Selected Colour

as per approved by Architect/Client. The rate shall be for all floors, at all heights, all shapes including

CNC / Engraving and all costs.

The frame work shall be made from square hollow aluminum anodized section size of 50x50x1.5 mm

& 25x50x1.5 mm of approved make conforming to IS code. The framework shall be fixed as per

drawing vertically @ 600 mm c/c & horizontal 600 mm c/c horizontally. which shall be provided from

gr. level to RCC slab / beams soffit level. Rates shall also be inclusive of cost of making CNC/engraving

/cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing

38 additional sections for strengthening around the openings/cutouts additional support for fixing of 8.00 SQMT 4500.00

patch fittings for doors, making grooves between wall & board, in filled with termite treated members

if required or as per drawing /instruction of EIC. All curved surfaces, recesses, waffles shall be part of

the paneling including Openable shutter wherever required area and finished with the same material.

Work complete including all type of material, fittings , fixtures, Finish, loading , unloading

transportation, all leads ,accessories, groove, adhesive ,tape, headless nails, sample mockup, all floor

all levels, all heights etc complete as per detailed drawings ,specifications & instruction of

Client/EIC.sample mock shall be approved from as per Architect/GRIMCO Manager &instruction.

Providing and fixing wooden Palmet of up to 50 to 150 mm Thick L shape made & 300 mm Height of

12mm thick ply with 4 mm thick mdf with colour as per IS 710 and beading of 4mm thick and 25mm

wide Ghana Teak wood for projection screen. Rates shall also be inclusive of cost of making

CNC/engraving /cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers

etc & providing additional sections for strengthening around the openings/cutouts additional support

for fixing of patch fittings for doors, making grooves between wall & board, in filled with termite

treated members if required or as per drawing /instruction of EIC. Rate to be inclusive of lipping,

cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and

for all floors as per drawing and approved sample etc should also take load of all the all roller blinds

as per Architect/GRIMCO Manager instruction.

Providing wood work in frames of Doors, windows cleare story windows and other similar works

wrought,frame and fixed in position including both Side 100 mm wide Panelling with Selected

Laminate. Providing & Fixing 12 mm Thick Plywood With Selected Laminate for Panelling . Rate Shall

be including Anodized aluminum fixtures & fastenings ,Adhesive Material ,& Necessary Hardware. the

Measurement shall be Consider Running Length X Width as directed by engineer in charge.

Providing & Fixing Wooden Partition with 10 mm Glass framing in Alluminium with both side cover

with 12mm thick comm. ply finished both Side with 1.0mm thick selected laminate, without any air

gap and grooving as per design& instruction of the EIC/Architect. wooden framing to be erected

above false ceiling make hole/face plate for conduit pipes of electrical / networking cables with

openable stud from partition Including all materials and labour etc. Open edges also finish with

laminate.Providing & Fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and

fixing full height glass partition made out of glazed partition with stanless steel U channel profile in the

top and Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The

glass to be butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between

two butt jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled

with clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

supplying & fixing 3m sparkle film/Fluted Film on glass with manufacturer specification, as per the

42 detailed technical specifications, drawings and as per Architect/GRIMCO Manager instruction. 25.00 SQMT 1200.00

Deep Cleaning Glass, Wall,Window ,Table with Require Material Broom,Dust Pan,Squeegee,Sprey

Cleaner,Mop as per Instruction of the Grimco Manager/Architect.

Providing and fixing Roller Blind fixed on window level on wooden batten and curtain lift with cotton

thin rope, design and colour as per instruction by engineer – in – Charge with necessary hardware

fitting, material and labour etc. complete as per detail drawing and instruction of engineer-in charge

and consultant.

Providing and fixing ACP Letters for Office Detail Name & addres Letters on ACP

fascia.Providing 3mm thick alluminium composite panel (ACP) sheet fascia and all side with

required iron angle / hollow heavy pipe structure frame. and back side cover up by aliminium

sheet ,complete box should be water-proof.and make it . Approx size of the Signages is

:5'X2'0"X0'5".Outdoor signage: 5 to 6 mm thick & ACP Letters / logo signage Complete as per

EIC/Architect Instruction.

Providing and Fixing Doormat (6' X 2') made up of synthetic material as per the approval from the

Architect / EIC.

Providing and Fixing Doormat ( Approx 1.5' X 2') made up of synthetic material as per the approval

from the Architect / EIC.

Providig & Fixing Wall Clock as per approved make. As per instruction at site approved by Architect of

Engineer in charge.

Providing, supplying SS 304 perforated Dustbin/ Wire mesh Dustbin as per approved make. As per

instruction at site approved by Architect of Engineer in charge.

Supplying labour for removing and filling all type Civil /Electrical HVAC of Debric incl. construction

50 waste materials and cleaning or any other type work for 8 hr. per day comp. as directed by eng. 9.00 EACH 1650.00

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with

51 textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with 24.00 Pt. 445.00

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single

52 mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / 12.00 Pt. 632.00

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type

53 of accessories. 11.00 Pt. 471.00

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling completeCat-III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type accessories. Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(9) 16 Amp. SP one way switch Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green)

both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below

type of pipe with 6A Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

57 modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or 2.00 Pt. 562.00

ceiling rose or H.D.Connector as directed.ss will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be

erected complete with earth continuity and necessary connection with primary light with accessories

erected on Metal / PVC / wooden box covered covered with appropriate front plate modules erected

on / in wall / ceiling for open / concealed wiring. with necessary Lamp holder / ceiling rose /

58 H.D.Connector as directed.as per pipe erected with following type of accessories.Note:- Maximum up 22.00 Pt. 166.00

to 6 mtrs length, excess will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories cat iii

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat-III

(4) TV Co-axial Socket outlet

(7) Blank Plate Single

(8) Modem Jack for Computer Open RJ-45

64 (19) Modular Indicating Call Bell Cat.III 1.00 EA 326.00

65 (20) Modular Buzzer Cat.III 1.00 EA 148.00

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

66 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 150.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

69 Check-nuts etc. complete of following sizes. 90.00 Mtr. 17.00

Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement

with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin

71 polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall / ceiling of following size . 60.00 Mtr. 31.00

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS with necessary end caps Internal and

72 external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following sizes 45.00 Mtr. 187.00

(3) 50 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

73 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 320.00 Mtr. 101.00

(a) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size

(a) 2 wire 4 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly -

75 Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. 95.00 Mtr. 39.00

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE

insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR

outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following

size of conductors & nos.of pairs. With necessary connections.

A. Conductor Size 0.5 mm

(a) (2) Unarmoured

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing & erecting main Distribution (MDF) indoor type, back mounted frame

(a) Suitable for 10 pair

ARMOURED ALLUMINIUM CABLES.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

79 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 10.00 Mtr. 152.00

d) 4 Core 16 Sq.mm.

80 c) 4 Core 10 Sq.mm. 50.00 Mtr. 139.00

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

81 armoured cable complete with out going tails, insulating tape etc for following size of cables. 2.00 Nos 38.00

(C) 2 to 4 core 10 Sq. mm

82 d) 2 to 4 Core 16 Sq.mm 2.00 Nos 47.00

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly

83 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut 8.00 Nos 13.00

bolts in an approved manner.

Providing and fixing printed instruction chart both in English and Gujarati and duly framed with front

85 glasses, for treatment of person suffering from Electric shock with minimum 50" diagonally size. 1.00 Nos 129.00

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

86 clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. 4.00 Ea 6526.00

[A] For 4.5 Kg Capacity

MINIATURE CIRCUIT BREAKERS.

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having

87 breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 12.00 Nos 111.00

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking

88 capacity & confirms to IS : 8828 in existing box having following capacity 1.00 Nos 276.00

(A) 6 to 32 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breaking

89 capacity & confirms to IS :8828 in existing box having following capacity 2.00 Nos 632.00

(b)40 Amp. Cat.III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

90 be used) 1.00 Nos 2885.00

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

EARTH LEAKAGE CIRCUIT BREAKERS.

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz.

91 having characteristic of quick action & tripping with all advance feature & do not incorporate any 3.00 Nos 2213.00

electronic component. for following Max. rating erected as directed

(ii) 40Amps. DP

CEILING FANS AND ACCESSORIS.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI

92 mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium 12.00 Nos 1929.00

blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in

FAN ACCESSORIES.

93 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly 1.00 Mtr. 107.00

painted for fan complete with necessary 24/ O.2, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Roundbar grouted in RCC slab with Making the site as

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

95 length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected 1.00 Nos 107.00

concealed in Ceiling with necessary finishing..

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with

necessary hook of 10 mm M.S. Round Bar.

97 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 1.00 Nos 18.00

TABLE FANS, EXHAUST FANS & ACCESSORIES.

98 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 1.00 Nos 1687.00

RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

99 Luminaire efficiency> 85 lumens/watt , 2.00 Nos 370.00

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)

(A) Tube Light with integral/ non-integral driver

(d) 22-24 Watts, Surge - 4KV,IP-20, 4 feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaire efficiency> 85 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)Square/ Circular Surface/Recessed Mounted

Downlight/Hanging with provision for spring loaded mounting clips complete.(b)16-20 watts, Surge-4

101 Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ 2.00 Kg. 77.00

Transformer LT panel board, Motors etc. using proper clamp.

102 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 2.00 kg 787.00

Removing all Electrical Material / equipment from existing set up , also handover to client

representative as per them requirement

104 Re use the electrical material as per Client's epresentative / architect team 's instruction 1.00 job 5000.00

Supplying and erecting Of 43 " UHD LED display for CCTV monitoring and checking .(the scope

includw the stand and other necessary accessasory to coplete the job .

Supplying & Erecting floor mounted/ table top single phase 50Hz water dispenser with SS 304 food

grade cold tank specification having three water tap of hot/cold/ambient water function, LED display

106 with storage capacity from 2.5 Ltrs to 3.2 Ltrs, cooling capacity 2.5ltrs/hr, including refrigerant with 1.00 Ea. 11443.00

20ltrs refrigerant storage capacity compartment inclusive 1No.water topping bottle

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

107 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 200.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE DHOLKA.

Sr. No. Description Quantity Unit Rate Amount

(8) Modem Jack for Computer Open RJ-45

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

110 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 2.00 no 47780.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.

(B) for 1.5 ton capacity - Premium Cat.

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with

accessories etc. duly connected separately erected evaporating unit and blower motor with its

accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star

and above of current year) with necessary core cutting.for 2 ton capacity

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

112 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 2.00 no 37983.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.[A] For 1 Ton Capacity Premium Cat.

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR

capacity erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and

control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Providing & Fixing 100X100 mm PVC Casing Patti for Drain Pipe/Electrical as per Architect/Grimco

Manager Instruction.

Misc.Civil Work Like Wall Jury,Cut Out & Opening to pass Piping Tray,wire ,pipes & Drain Pipes

116 Including with Refinishing & Plastering of the Same to the Original Finish. 1.00 JOB WORK 9500.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Removing/Shifting existing TW partitions/Panelling/Curtain/Furniture including

hardware/Civil/Sanitary/Piping Work etc including stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift and the site shall be cleaned as directed by EIC. Care shall

be taken to remove the partition / door so as to reuse the same.

Removing Ac,OutDoor & Accessories and Handover the Client as per Architect/Grimco Manager

Instruction. Care shall be taken to remove the AC so as to reuse the same.

CHIPPING CONCRETE WORK :Chipping of unsound weak concrete material from slab, beam, column

and around the reinforcement incl. plaster etc. with manual chiselling with standard power driven

percussion type of pneumatic chisel of standard make as directed by Eng. In Charge incl. tapering all

edges and making square shoulders of cavities etc. comp. and disposal of debris outside the premises

incl. cleaning of exposed reinforcement using approved alkaline chemical rust remover (doctor fix it

rust remover or its equivalent chemical comp. as per manufacturers specification) (Area of RCC surface

is to be measured for payment) etc. incl applying 10 to 15 mm avg. thick plaster in C.M. (1:3) incl.

curing, scaffolding, curing, Existing Removing & Scrape Plaster etc. comp. as directed by Grimco

Manager /Architect.

MASONARY WORK: Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement :4 -coarse sand) in

(Conventional) Rate Shall Be Consider All Floor & Work Shall be Execute as per Architect

Grimco Manager Instruction.

Providing Brick masonary using common burnt clay building bricks for foundation and plinth

having crushing strength not less than 35 kg./ Sq. Cm. in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) incl. watering,curing,scaffolding and racking out joints etc. comp as per directed by

PLASTER WORK : Providing 15mm thik. Cement plaster in single coat on Internal Walls for interior

6 plastering of following finished even and smooth in Cement Mortar 1:3 (1-Cement : 3-Sand) incl. 7.00 SQMT 203.34

finishing with a floating coat of neat cement slurry.

FLOORING: Providing and Laying Glossy/mat Finished vitrified tiles of size 800 X 800mm and 8 mm to

10mm thick of approved make and colour having homogeneous materials in flooring laid on 20mm

thick average cement mortar 1:3 (1 cement: 3 coarse sand)as directed by Engineer in charge. Applying

spacer of 4mm and not less than 2mm depth of epoxy grooving of lavicrete , Roff equivalents directed

by Engineer in charge. incl. cost of fixing materials, labour, tools, plants, equipotent incl. all lead & lift

Supplying & fixing heavy duty 800 X 800 mm Vitrified tiles of 8 to 9 mm the of Approved Brand in

Skirting as per approved pattern ,Match Shade with Existing Flooring & design laid over neat cement

slurry & cement mortar in (1:6) bedding 20 mm the average & joint with colour cement slurry incl.

special cornices, corners or angles, tiles etc. incl.Applying spacer of 4mm and not less than 2mm depth

of epoxy grooving of lavicrete , Roff equivalentas directed by Engineer in charge. incl. cost of fixing

materials,labour, tools, plants, equiptnent incl. all lead & lift comp, labour, tools, plants, equipmens

incl. all lead & lift comp. as directed by Architect /EIC .

Removing & Refixing Grill as per Architect /Grimco Manager Instruction Rate Shall be Including

9 Loading,Unloading,Labour,Welding,Hardware etc.Care shall be taken to remove the Grill so as to reuse 2.00 EACH 500.00

Providing & Fixing window having extruded aluminium colour anodized section frame main outer size

63.5 x38.1x1.95mm(Jindal or Hindalco section No.4605 @ Wt.1.094 Kg/Rmt) horizontal Two Track

member size 61.85x31.75x1.2mm(of Jindal or Hindalco section No.8687 @ Wt.of 0.695 Kg/mt.) vertical

member of size 61.85x 31.75x1.3mm (of Jindal or Hindalco section No. 8758 @ wt of 0.659 Kg/Mt.)

with Sluiding shutter of horizontal member size 40x18x1.29mm (of Jindal or Hindalco section No.

@ wt.of 0.456 kg/mt.) vertical member of size 40x18x1.29mm (of jindal or Hindalco section No.8947

@ wt.of 0.456 Kg/ mt./section 8948 @ wt of 0.457 kg/mt.) with 5mm thick transperant bronze colour

tinted float glass with colour anodized aluminium fittings & fixtures with transparent silicon sealant

glass fixing to frame as per detail .

applying primer coat of the paint, Putty shall be applying walls and ceiling for making even surface up

to finish level.Providing and applying even coats of acrylic emulsion paint / on walls and ceiling up to

final finish. Shade and texture of the paint shall be as approved by Architect or EIC. Application of paint

shall be with brush and last coat of paint shall be applied with a standard company roller all as

approved by architect/Grimco Manager.rates are inclusive cost of paint, putty, primer, brush,

roller,Removing Existing Paint, scaffolding cleaning charges etc. complete.

Providing and applying synthetic enamel paint (and Repair Grill/M.s. as per Site Situation-Proper

Finishing , Levelling,Welding, Cleaning) of Asian/Nerolac/ICI/Lewis Berger/J&N of approved brand to

12 previously painted steel work with one coat of approved quality and brand paint of Asian, Nerolac, ICI, 8.00 SQMT 250.00

Berger, Johnson make and of required shade, including cleaning and scrapping the surface with sand

paper etc. complete as directed.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

FALSE FLOORING (Stage) Providing & Fixing ms Structure Vertical Stand 50X50X5 mm 600 X

mm center to Center Distance with Anticorrosive Paint and above Stand 25 X 25X5 mm square Hollow

13 Pipe With Anticorrissive Paint by Steel Welded Construction. Outer All Exposed Part Shall be Fitted 4.00 SQMT 7000.00

Square Hollow Pipe & 18 mm Plywood With Laminate with Adhesive Material , Nail Scrue Abro tap Etc

all Required Hardware.

FULL HEIGHT /LOW HEIGHT PARTITION (FULLY SOLID) (75mm thk.) Providing and fixing full height /

half height double skin wooden partition upto ceiling or beam bottom as per drawing and framing in

Alluminium with both side cover with 12mm thick comm. ply finished both Side with 1.0mm thick

selected laminate, without any air gap and grooving as per design& instruction of the EIC/Architect.

wooden framing to be erected above false ceiling make hole/face plate for conduit pipes of electrical /

networking cables with openable stud from partition Including all materials and labour etc. Open

edges also finish with laminate. complete as per detail drawing and instruction of Architect/engineer-

Providing and fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and fixing full

height glass partition made out of glazed partition with stanless steel U channel profile in the top and

Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The glass to be

butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between two butt

15 jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled with clear 6.00 SQMT 4800.00

silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be Including

Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by the

Architect. including hardware.

Providing and fixing 35 mm thick Decorative type Water proof flush door shutters, solid core

construction with wood frame with Polish of ground class hard-wood with cross band and face ply-

wood face panels, 1.0 mm thick laminate on both sides including the top Portion ( Aprox 0.380mm

Height ) Pack With Transperent Glass With Ply Frame, Stainless steel fixtures and fastening like

,Handle,Lock , stopper including for door shutters sides etc complete. as directed by engineer in

Door Laminate Change. To be Removed & Refixing .Providing and Fixing Both Side 1 mm laminate &

Existing Removing Laminate Door of washable type material of good quality with appropriate adhesive

of approved quality like fevicol or its equivalent brands with smooth finishing and in line level with

regular edges as per requirement and site situation incl. cutting and any necessary cut outs of Glass

and Cutout Finish With Plywood With Selected Laminate & Door if any required etc. comp. in all

respects. All rates are inclusive of hardware like, nails, screws, abro taps, adhesive etc. complete.

Providing ,Removing Existing Door Closer and fixing Door Closer and Blue Space GPRH Solid Standoffs

18 Heavy-Duty Commercial Grade-304 Stainless Steel Push Pull Door Handle as per Architect & EIC 1.00 EACH 2500.00

Instruction. Rate Shall be Including Fitting Charge.

Table (1.95 x 0.750 x 0.75) Providing and fixing the Table with top of 19 mm thick BWR plywood&

Table Top Side Boarder added 19 mm Plywood in Below Side with post formed approved laminate The

side leg should be made of Wood box with laminate. CPU box with made of 18mm. thick plywood and

1mm. thick laminate on all exposed side.The apron should be made of 18mm. thick plywood and for

elevation 18mm. thick one side BWR ..Plywood patta as shown in drawing and finished with 1mm.

thick laminate. Footrest (0.60 x 0.38) should be made from 18mm. BWR plywood with 1mm laminated

finish in the approved shade. Including all materials and labour etc. complete as per detailed drawing

and instructions of engineer-in-charge.

19 Side Table (1.225x 0.45 x 0.75) Providing and fixing Side Table for 25mm thick (BWR board,) post 1.00 EACH 22500.00

forming laminated top with 6mm thick BWR plywood at backside finished with 1mm. thick approved

laminate, made out of 18mm thick BWR plywood with exterior side 1mm. and interior side 0.6mm.

Approved laminate. Drawer unit box (measurement shown in drawing) with wooden bedding

patti/PVC, lock and telescopic channel. Key board tray will be made of 18mm. thick post foamed BWR

plywood with telescopic chanel. Shutter will be made of 18mm. thick post forming BWR with magnet,

multiple drawer lock, S.S. legs (75mm height) in bottom, auto hinges of HAFELE or equivalent.

Including all materials and labour etc. complete as per detailed drawing and instructions of engineer-

Linear / Running Counter For Work Station.Providing and Fixing Linear / Running Counters of 4' Wide

width 2' made up of 18 mm thick Plywood. The table top shall be finished with 1 mm thick laminate of

approved make and the edge shall be finished with 12 mm wooden bidding duly finished in polish /

duco paint to match with the laminate of the table top. Providing & Supplying Work Station Between

Glass Partition Soft Board.The table shall be provided with drawer pedestal unit made up of 18 mm

thick MR ply and drawers shall be running on approved make EBCO / Hettich / Haffele make telescopic

channels. The handle lock etc. shall be of the similar make. The workstation also shall be provided with

each of key board tray, CPU trolley and foot rest of EBCO / Innofitt make as per the instructions of

Engineer-in-charge / Architects.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Low Height/ Full Height Storage - Providing, Supplying & Fixing Basic Str. in 19 mm Ply wood, Outer

Side 1 mm Laminate in position for Storage and Inner 0.5 yo 0.6 mm Laminate of washable type

material of good quality with appropriate adhesive of approved quality like fevicol or its equivalent

21 brands with smooth finishing and in line level with regular edges as per Arch./ EIC Instruction incl. 4.00 SQMT 9000.00

cutting and any necessary cut outs of Storage & Door if any required etc comp. in all respects. All rates

are inclusive of hardware like, nails, screws,abro taps, Lock , Handle , Auto hinge , adhesive etc.

GLASS DOOR: Providing and fixing in position full height 12mm thick toughened glass STL45 Door

System with 6063-T6 grade duly Anodized Aluminium Sections having sizes of 45x55x1.5mm thick,

mm Toughened Glass including Assa Abloy Door Closure /Floor Spring , Hinges, SS Handle (H Type

450mm), SS Bottom Lock, Thermoplastic Gaskets & Screw Caps all necessary hardware of as per

22 approved make by Architect. 10mm thick Saint Gobain make customized clear toughened glass.Work 10 SQMT 5880.00

complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, all

leads ,accessories, sample mockup, all floor , all levels, all heights , necessary frame work,Scafffolding

etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

MANAGER CABIN MAIN CHAIR Adj. Arms Larger Seats seat size: 47.0 cm. (w) x 51.5 cm. (d) back size

:45.0 cm. (w) x 65.3 cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should be

moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. armrests : the

armrests have an up-down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure.

armrest top has an integrated layer of thermoplastic elastomer (tpe).

lumbar support assembly: the lumbar support consshould be ts of polypropylene pad with moulded

polyurethane foam & covered with polyester fabric. the height of lumbar pad can be adjusted through

two projecting knobs provided on the rear side of the pad. lumbar pad has an adjustment of 8.0 ±

front pivot synchro mechanism: the adjustable tilting mechanism should be designed with the

following features.

23 • 360° revolving type. 1 EACH 15000.00

• single point control.

• front-pivot for tilt with feet resting on ground ensuring more comfort.

• tilt tension adjustment.

• 4-position locking with anti-shock feature.

• seat/back tilting ratio of 1:2.

pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ±

pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted

with 5 nos. twin wheel castors. the pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm.

with castors).twin wheel castors: the twin wheel castors should be injection moulded in black

nylon.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE:

Staff Chair the seat should be made up of 1.2 ±0.1cm. thick hot-pressed

plywood , upholstered with fabric upholstery covers and moulded polyurethane foam.

seat size: 47.0 cm. (w) x 48.0 cm. (d)back : the back asembly. should be made of powder coated (oft

40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with

contoured lumbar support for extra comfort. the back should be upholstered using double layer

spacer mesh fabric with high tenacity yarn.

back size : 46.5 cm (w) x 60.5 cm (h)high resilience (hr) polyurethane foam: the hr polyurethane foam

should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25%

compression.armrests: the one-piece armrests should be injection moulded from black co-polymer

polypropylene. Centre-tilt mechanism: the mechashould be m should be designed with the following

24 • 360° revolving type. 5 EACH 8700.00

• 17° ±2° maximum tilt on pivot at centre

• upright position locking.

tilt tension adjustment. .pneumatic height adjustment: the pneumatic height adjustment has an

adjustment stroke of 11.0 ±0.3cm.elescopic bellow assy: the bellow should be 3 piece telescopic type

and injection moulded in black polypropylene.pedestal .: the pedestal should be injection moulded in

black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be

±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)twin wheel castors: the twin wheel castors should

be injection moulded in black nylon.Overall Dimensions of Chair-Seat Height - min 43.3 to max

Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm

and Depth-76.3 cm.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

25 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 19000.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts.

Providing & Fixing Cushionon Seating & Back as per Instruction. The Shell to be assembled on the cross

beam with help of M8 Bolts.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

26 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 17500.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

GYPSUM BOARD CELLING : Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender

channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making

necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

595 x 595 MM CELLING:Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light

weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 1200X600mm and secondary

28 cross ’T’ of length 600mm and size600mm centre to centre to form agrid of 24x28mm made of 0.30 30 SQMT 1632.63

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm

centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified

edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in

the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I.

slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners,

4mm G.I. adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm

centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with

polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer-

incharge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No

SS plate Signage: 450mm X 100mm - Stainless Steel satin finished flat etching plate of 1.5mm thick.

Providing Making and fixing of various in-door signage, as & where basis. sign in ISI Brushed S.S. Grade

304 letters in English letter + All text and design in acid process, each plates. Each text & design with

respective color coated complete plate. The SS mounted on glass or any non holes surfaced by 3M

29 double sided tape with required chemical process, guidelines by 3M company. Whereas, Any other 4 EACH 1800.00

then glass surface, SS plate mounted by Two side screws with required grips nd holes on the wall with

two SS spacer screws. The item should be as per instruction at site approved by Architect of Engineer

in charge. The rate shall be inclusive of scaffolding, drilling, adhesive material etc. at all height.

Providing & Arranging wheel chair for physically handicapped person having dimension 790(L) x

600(W) x 700(H)mm. With foldable frame structure made of carbon steel setcion 22mm x 1.2mm or as

per direction of engineer in charge. A3 carbon sheet with chrome finish cross bars made of A3 carbon

steel material with setcion 25.4mm x 1.2mm., 24 inch solid mag wheels with alloy in the rim, hand rim

of setcion 16mm x 1.2mm. carbon steel with chrome finish, front wheel of 8 inch HUB made of PA

30 polymer & outer side of solid rubber PU moulded arm rest & base made of ABS, leather finish calf rest 1 EACH 13570.00

& seat with cushion alluminium foot rest with updown movement having extended base foot press

with moulded plastic including hand brakes & full structure is anti rust chrome finish with users

capacity of 100 kg including all necessary fixture, fastners, fittings, labour, material, machinary etc.

complete as seletced and diretced by Engineer-in-charge.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Providing & fixing S.S. Pipe railing of 50mm dia pipe not less than 18guage, in 3 rows supported by S.S.

Pipe of 50mm dia at every corners & 1.5 mt C/C incl. concrete block (0.35 X 0.35 X 0.35) incl. 16 guage

S.S. sheet using required cutting, jointing, welding, threading, drilling & fixing etc. comp. as directed as

per drawing (For Platform)

Providing & Fixing Shelf Adhesive Tractile Tiles as per Architect/ GRIMCO manager Instruction. The

Tiles shall be Fixed with Suitable Adhesive Material with All required Additional Hardware Suppot. Rate

shall be Including Transportation , All Floor , Hardware, Adhesive Material etc.

Fixing Ipsa Super Strong Handsfree Foot Operated Pull (304 s.s)door latches of sizes 100mm with

necessary screws etc. complete

Painting lines, dashes, arrows, letters etc on roads, Air- fields and like in two coats with road marking

paint, brushing including cleaning the surface of all dirt, dust and other foreign matter (ii) over

Providing and fixing required size Stainless steel plate of 1.0mm thickness with regular

printed signage at top in black colour at top part of plate and respective brialle lipi

sgnages at bottom part the plate, S.S. Plate to be fixed on 10mm thick clear acrylic

sheet, this whole assembly to be fixed on wall with four numbers of SS studs etc

complete as per instructions of engineer in-charge.

DEDO WORK (600X600 mm):'Providing & laying Antiskid Vitrified 12mm thick tiles flooring, treads of

steps and landing laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface and jointed with colour cement slurry including finished with flush pointing &

36 cleaning the surface etc. completed of any Shade and approved by Higher Authority of approved 135.00 SQMT 1446.99

brands & Size. Providing & Applying spacer of 5mm and not less than 4mm depth of epoxy grooving of

levirate , Ruff equivalents as per detailed drawing and as directed by Grimco Manager /Architect. Basic

Cost of Tiles is Rs 50/-sqft

Scraping of old paint/ distemper wherever necessary from the existing walls, and applying of 4.0 to

37 mm thick lime over it to give a smooth leveled finish, the final coat to have one coat of oil based 202.00 SQMT 255.00

Cement primer the cost shall include all labor , materials, etc complete.

Providing & fixing 18mm thick cement sheet/18 mm Plywood for panelling work with Selected Colour

as per approved by Architect/Client. The rate shall be for all floors, at all heights, all shapes including

CNC / Engraving and all costs.

The frame work shall be made from square hollow aluminum anodized section size of 50x50x1.5 mm &

25x50x1.5 mm of approved make conforming to IS code. The framework shall be fixed as per drawing

vertically @ 600 mm c/c & horizontal 600 mm c/c horizontally. which shall be provided from gr. level

to RCC slab / beams soffit level. Rates shall also be inclusive of cost of making CNC/engraving /cut

outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing

38 additional sections for strengthening around the openings/cutouts additional support for fixing of 8.00 SQMT 4500.00

patch fittings for doors, making grooves between wall & board, in filled with termite treated members

if required or as per drawing /instruction of EIC. All curved surfaces, recesses, waffles shall be part of

the paneling including Openable shutter wherever required area and finished with the same material.

Work complete including all type of material, fittings , fixtures, Finish, loading , unloading

transportation, all leads ,accessories, groove, adhesive ,tape, headless nails, sample mockup, all floor

all levels, all heights etc complete as per detailed drawings ,specifications & instruction of

Client/EIC.sample mock shall be approved from as per Architect/GRIMCO Manager &instruction.

Providing and fixing wooden Palmet of up to 50 to 150 mm Thick L shape made & 300 mm Height of

12mm thick ply with 4 mm thick mdf with colour as per IS 710 and beading of 4mm thick and 25mm

wide Ghana Teak wood for projection screen. Rates shall also be inclusive of cost of making

CNC/engraving /cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers

etc & providing additional sections for strengthening around the openings/cutouts additional support

for fixing of patch fittings for doors, making grooves between wall & board, in filled with termite

treated members if required or as per drawing /instruction of EIC. Rate to be inclusive of lipping,

cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and

for all floors as per drawing and approved sample etc should also take load of all the all roller blinds as

per Architect/GRIMCO Manager instruction.

Providing wood work in frames of Doors, windows cleare story windows and other similar works

wrought,frame and fixed in position including both Side 100 mm wide Panelling with Selected

Laminate. Providing & Fixing 12 mm Thick Plywood With Selected Laminate for Panelling . Rate Shall

be including Anodized aluminum fixtures & fastenings ,Adhesive Material ,& Necessary Hardware. the

Measurement shall be Consider Running Length X Width as directed by engineer in charge.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Providing & Fixing Wooden Partition with 10 mm Glass framing in Alluminium with both side cover

with 12mm thick comm. ply finished both Side with 1.0mm thick selected laminate, without any air

gap and grooving as per design& instruction of the EIC/Architect. wooden framing to be erected

above false ceiling make hole/face plate for conduit pipes of electrical / networking cables with

openable stud from partition Including all materials and labour etc. Open edges also finish with

laminate.Providing & Fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and

fixing full height glass partition made out of glazed partition with stanless steel U channel profile in the

top and Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The

glass to be butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between

two butt jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled

with clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

supplying & fixing 3m sparkle film/Fluted Film on glass with manufacturer specification, as per the

42 detailed technical specifications, drawings and as per Architect/GRIMCO Manager instruction. 16.00 SQMT 1200.00

Deep Cleaning Glass, Wall,Window ,Table with Require Material Broom,Dust Pan,Squeegee,Sprey

Cleaner,Mop as per Instruction of the Grimco Manager/Architect.

Providing and fixing Roller Blind fixed on window level on wooden batten and curtain lift with cotton

thin rope, design and colour as per instruction by engineer – in – Charge with necessary hardware

fitting, material and labour etc. complete as per detail drawing and instruction of engineer-in charge

and consultant.

Providing and fixing ACP Letters for Office Detail Name & addres Letters on ACP

fascia.Providing 3mm thick alluminium composite panel (ACP) sheet fascia and all side with

required iron angle / hollow heavy pipe structure frame. and back side cover up by aliminium

sheet ,complete box should be water-proof.and make it . Approx size of the Signages is

:5'X2'0"X0'5".Outdoor signage: 5 to 6 mm thick & ACP Letters / logo signage Complete as per

EIC/Architect Instruction.

Providing and Fixing Doormat (6' X 2') made up of synthetic material as per the approval from the

Architect / EIC.

Providing and Fixing Doormat ( Approx 1.5' X 2') made up of synthetic material as per the approval

from the Architect / EIC.

Providig & Fixing Wall Clock as per approved make. As per instruction at site approved by Architect of

Engineer in charge.

Providing, supplying SS 304 perforated Dustbin/ Wire mesh Dustbin as per approved make. As per

instruction at site approved by Architect of Engineer in charge.

Supplying labour for removing and filling all type Civil /Electrical HVAC of Debric incl. construction

50 waste materials and cleaning or any other type work for 8 hr. per day comp. as directed by eng. 6.00 EACH 1650.00

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with

51 textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with 17.00 Pt. 445.00

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single

52 mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / 8.00 Pt. 632.00

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of

53 accessories. 10.00 Pt. 471.00

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling completeCat-III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type accessories. Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(9) 16 Amp. SP one way switch Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green)

both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below

type of pipe with 6A Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

57 modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or 2.00 Pt. 562.00

ceiling rose or H.D.Connector as directed.ss will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-III

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be

erected complete with earth continuity and necessary connection with primary light with accessories

erected on Metal / PVC / wooden box covered covered with appropriate front plate modules erected

on / in wall / ceiling for open / concealed wiring. with necessary Lamp holder / ceiling rose /

58 H.D.Connector as directed.as per pipe erected with following type of accessories.Note:- Maximum up 15.00 Pt. 166.00

to 6 mtrs length, excess will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-III

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories cat iii

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat-III

(4) TV Co-axial Socket outlet

(7) Blank Plate Single

(8) Modem Jack for Computer Open RJ-45

64 (19) Modular Indicating Call Bell Cat.III 1.00 EA 326.00

65 (20) Modular Buzzer Cat.III 1.00 EA 148.00

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

66 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 180.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

69 Check-nuts etc. complete of following sizes. 95.00 Mtr. 17.00

Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement

with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin

71 polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall / ceiling of following size . 65.00 Mtr. 31.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS with necessary end caps Internal and

72 external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following sizes 50.00 Mtr. 187.00

(3) 50 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

73 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 330.00 Mtr. 101.00

(a) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size

(a) 2 wire 4 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly -

75 Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. 100.00 Mtr. 39.00

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE

insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR

outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following

76 size of conductors & nos.of pairs. With necessary connections. 300.00 Mtr. 20.00

A. Conductor Size 0.5 mm

(a) (2) Unarmoured

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing & erecting main Distribution (MDF) indoor type, back mounted frame

(a) Suitable for 10 pair

ARMOURED ALLUMINIUM CABLES.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

79 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 10.00 Mtr. 152.00

d) 4 Core 16 Sq.mm.

80 c) 4 Core 10 Sq.mm. 50.00 Mtr. 139.00

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

81 armoured cable complete with out going tails, insulating tape etc for following size of cables. 2.00 Nos 38.00

(C) 2 to 4 core 10 Sq. mm

82 d) 2 to 4 Core 16 Sq.mm 2.00 Nos 47.00

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly

83 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut 8.00 Nos 13.00

bolts in an approved manner.

Providing and fixing printed instruction chart both in English and Gujarati and duly framed with front

85 glasses, for treatment of person suffering from Electric shock with minimum 50" diagonally size. 1.00 Nos 129.00

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

86 clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. 3.00 Ea 6526.00

[A] For 4.5 Kg Capacity

MINIATURE CIRCUIT BREAKERS.

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having

87 breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 10.00 Nos 111.00

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking

88 capacity & confirms to IS : 8828 in existing box having following capacity 1.00 Nos 276.00

(A) 6 to 32 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breaking

89 capacity & confirms to IS :8828 in existing box having following capacity 2.00 Nos 632.00

(b)40 Amp. Cat.III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

90 be used) 1.00 Nos 2885.00

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door

EARTH LEAKAGE CIRCUIT BREAKERS.

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz.

91 having characteristic of quick action & tripping with all advance feature & do not incorporate any 3.00 Nos 2213.00

electronic component. for following Max. rating erected as directed

(ii) 40Amps. DP

CEILING FANS AND ACCESSORIS.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI

92 mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium 8.00 Nos 1929.00

blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in

FAN ACCESSORIES.

93 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly 1.00 Mtr. 107.00

painted for fan complete with necessary 24/ O.2, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Roundbar grouted in RCC slab with Making the site as

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

95 length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected 1.00 Nos 107.00

concealed in Ceiling with necessary finishing..

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with

necessary hook of 10 mm M.S. Round Bar.

97 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 1.00 Nos 18.00

TABLE FANS, EXHAUST FANS & ACCESSORIES.

98 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 1.00 Nos 1687.00

RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

99 Luminaire efficiency> 85 lumens/watt , 2.00 Nos 370.00

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)

(A) Tube Light with integral/ non-integral driver

(d) 22-24 Watts, Surge - 4KV,IP-20, 4 feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaire efficiency> 85 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)Square/ Circular Surface/Recessed Mounted

Downlight/Hanging with provision for spring loaded mounting clips complete.(b)16-20 watts, Surge-4

101 Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ 2.00 Kg. 77.00

Transformer LT panel board, Motors etc. using proper clamp.

102 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 2.00 kg 787.00

Removing all Electrical Material / equipment from existing set up , also handover to client

representative as per them requirement

104 Re use the electrical material as per Client's epresentative / architect team 's instruction 1.00 job 5000.00

Supplying and erecting Of 43 " UHD LED display for CCTV monitoring and checking .(the scope

includw the stand and other necessary accessasory to coplete the job .

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE KAPADVANJ.

Description Quantity Unit Rate Amount

Supplying & Erecting floor mounted/ table top single phase 50Hz water dispenser with SS 304 food

grade cold tank specification having three water tap of hot/cold/ambient water function, LED display

106 with storage capacity from 2.5 Ltrs to 3.2 Ltrs, cooling capacity 2.5ltrs/hr, including refrigerant with 1.00 Ea. 11443.00

20ltrs refrigerant storage capacity compartment inclusive 1No.water topping bottle

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

107 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 200.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

(8) Modem Jack for Computer Open RJ-45

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

110 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 1.00 no 47780.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.

(B) for 1.5 ton capacity - Premium Cat.

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with

111 accessories etc. duly connected separately erected evaporating unit and blower motor with its 2.00 no 60245.00

accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star and

above of current year) with necessary core cutting.for 2 ton capacity

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

112 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 1.00 no 37983.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.[A] For 1 Ton Capacity Premium Cat.

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR

capacity erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and

control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Providing & Fixing 100X100 mm PVC Casing Patti for Drain Pipe/Electrical as per Architect/Grimco

Manager Instruction.

Misc.Civil Work Like Wall Jury,Cut Out & Opening to pass Piping Tray,wire ,pipes & Drain Pipes

116 Including with Refinishing & Plastering of the Same to the Original Finish. 1.00 JOB WORK 9500.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Removing/Shifting existing TW partitions/Panelling/Curtain/Furniture including

hardware/Civil/Sanitary/Piping Work etc including stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift and the site shall be cleaned as directed by EIC. Care shall

be taken to remove the partition / door so as to reuse the same.

Removing Ac,OutDoor & Accessories and Handover the Client as per Architect/Grimco Manager

Instruction. Care shall be taken to remove the AC so as to reuse the same.

CHIPPING CONCRETE WORK :Chipping of unsound weak concrete material from slab, beam, column

and around the reinforcement incl. plaster etc. with manual chiselling with standard power driven

percussion type of pneumatic chisel of standard make as directed by Eng. In Charge incl. tapering all

edges and making square shoulders of cavities etc. comp. and disposal of debris outside the premises

incl. cleaning of exposed reinforcement using approved alkaline chemical rust remover (doctor fix it

rust remover or its equivalent chemical comp. as per manufacturers specification) (Area of RCC surface

is to be measured for payment) etc. incl applying 10 to 15 mm avg. thick plaster in C.M. (1:3) incl.

curing, scaffolding, curing, Existing Removing & Scrape Plaster etc. comp. as directed by Grimco

Manager /Architect.

MASONARY WORK: Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement :4 -coarse sand) in

(Conventional) Rate Shall Be Consider All Floor & Work Shall be Execute as per Architect

Grimco Manager Instruction.

Providing Brick masonary using common burnt clay building bricks for foundation and plinth

having crushing strength not less than 35 kg./ Sq. Cm. in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) incl. watering,curing,scaffolding and racking out joints etc. comp as per directed by

PLASTER WORK : Providing 15mm thik. Cement plaster in single coat on Internal Walls for interior

6 plastering of following finished even and smooth in Cement Mortar 1:3 (1-Cement : 3-Sand) incl. 4.00 SQMT 203.34

finishing with a floating coat of neat cement slurry.

FLOORING: Providing and Laying Glossy/mat Finished vitrified tiles of size 800 X 800mm and 8 mm to

10mm thick of approved make and colour having homogeneous materials in flooring laid on 20mm

thick average cement mortar 1:3 (1 cement: 3 coarse sand)as directed by Engineer in charge. Applying

spacer of 4mm and not less than 2mm depth of epoxy grooving of lavicrete , Roff equivalents directed

by Engineer in charge. incl. cost of fixing materials, labour, tools, plants, equipotent incl. all lead & lift

Supplying & fixing heavy duty 800 X 800 mm Vitrified tiles of 8 to 9 mm the of Approved Brand in

Skirting as per approved pattern ,Match Shade with Existing Flooring & design laid over neat cement

slurry & cement mortar in (1:6) bedding 20 mm the average & joint with colour cement slurry incl.

special cornices, corners or angles, tiles etc. incl.Applying spacer of 4mm and not less than 2mm depth

of epoxy grooving of lavicrete , Roff equivalentas directed by Engineer in charge. incl. cost of fixing

materials,labour, tools, plants, equiptnent incl. all lead & lift comp, labour, tools, plants, equipmens

incl. all lead & lift comp. as directed by Architect /EIC .

Removing & Refixing Grill as per Architect /Grimco Manager Instruction Rate Shall be Including

9 Loading,Unloading,Labour,Welding,Hardware etc.Care shall be taken to remove the Grill so as to reuse 2.00 EACH 500.00

Providing & Fixing window having extruded aluminium colour anodized section frame main outer size

63.5 x38.1x1.95mm(Jindal or Hindalco section No.4605 @ Wt.1.094 Kg/Rmt) horizontal Two Track

member size 61.85x31.75x1.2mm(of Jindal or Hindalco section No.8687 @ Wt.of 0.695 Kg/mt.) vertical

member of size 61.85x 31.75x1.3mm (of Jindal or Hindalco section No. 8758 @ wt of 0.659 Kg/Mt.)

with Sluiding shutter of horizontal member size 40x18x1.29mm (of Jindal or Hindalco section No.

@ wt.of 0.456 kg/mt.) vertical member of size 40x18x1.29mm (of jindal or Hindalco section No.8947 @

wt.of 0.456 Kg/ mt./section 8948 @ wt of 0.457 kg/mt.) with 5mm thick transperant bronze colour

tinted float glass with colour anodized aluminium fittings & fixtures with transparent silicon sealant

glass fixing to frame as per detail .

applying primer coat of the paint, Putty shall be applying walls and ceiling for making even surface up

to finish level.Providing and applying even coats of acrylic emulsion paint / on walls and ceiling up to

final finish. Shade and texture of the paint shall be as approved by Architect or EIC. Application of

paint shall be with brush and last coat of paint shall be applied with a standard company roller all as

approved by architect/Grimco Manager.rates are inclusive cost of paint, putty, primer, brush,

roller,Removing Existing Paint, scaffolding cleaning charges etc. complete.

Providing and applying synthetic enamel paint (and Repair Grill/M.s. as per Site Situation-Proper

Finishing , Levelling,Welding, Cleaning) of Asian/Nerolac/ICI/Lewis Berger/J&N of approved brand to

12 previously painted steel work with one coat of approved quality and brand paint of Asian, Nerolac, ICI, 10.00 SQMT 250.00

Berger, Johnson make and of required shade, including cleaning and scrapping the surface with sand

paper etc. complete as directed.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

FALSE FLOORING (Stage) Providing & Fixing ms Structure Vertical Stand 50X50X5 mm 600 X 1200 mm

center to Center Distance with Anticorrosive Paint and above Stand 25 X 25X5 mm square Hollow Pipe

13 With Anticorrissive Paint by Steel Welded Construction. Outer All Exposed Part Shall be Fitted Square 6.00 SQMT 7000.00

Hollow Pipe & 18 mm Plywood With Laminate with Adhesive Material , Nail Scrue Abro tap Etc all

Required Hardware.

FULL HEIGHT /LOW HEIGHT PARTITION (FULLY SOLID) (75mm thk.) Providing and fixing full height / half

height double skin wooden partition upto ceiling or beam bottom as per drawing and framing in

Alluminium with both side cover with 12mm thick comm. ply finished both Side with 1.0mm thick

selected laminate, without any air gap and grooving as per design& instruction of the EIC/Architect.

wooden framing to be erected above false ceiling make hole/face plate for conduit pipes of electrical /

networking cables with openable stud from partition Including all materials and labour etc. Open

edges also finish with laminate. complete as per detail drawing and instruction of Architect/engineer-

Providing and fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and fixing full

height glass partition made out of glazed partition with stanless steel U channel profile in the top and

Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The glass to be

butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between two butt

15 jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled with 7.00 SQMT 4800.00

clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

Providing and fixing 35 mm thick Decorative type Water proof flush door shutters, solid core

construction with wood frame with Polish of ground class hard-wood with cross band and face ply-

wood face panels, 1.0 mm thick laminate on both sides including the top Portion ( Aprox 0.380mm

Height ) Pack With Transperent Glass With Ply Frame, Stainless steel fixtures and fastening like

,Handle,Lock , stopper including for door shutters sides etc complete. as directed by engineer in

Door Laminate Change. To be Removed & Refixing .Providing and Fixing Both Side 1 mm laminate &

Existing Removing Laminate Door of washable type material of good quality with appropriate

adhesive of approved quality like fevicol or its equivalent brands with smooth finishing and in line

level with regular edges as per requirement and site situation incl. cutting and any necessary cut outs

of Glass and Cutout Finish With Plywood With Selected Laminate & Door if any required etc. comp. in

all respects. All rates are inclusive of hardware like, nails, screws, abro taps, adhesive etc. complete.

Providing ,Removing Existing Door Closer and fixing Door Closer and Blue Space GPRH Solid Standoffs

18 Heavy-Duty Commercial Grade-304 Stainless Steel Push Pull Door Handle as per Architect & EIC 3.00 EACH 2500.00

Instruction. Rate Shall be Including Fitting Charge.

Table (1.95 x 0.750 x 0.75) Providing and fixing the Table with top of 19 mm thick BWR plywood&

Table Top Side Boarder added 19 mm Plywood in Below Side with post formed approved laminate The

side leg should be made of Wood box with laminate. CPU box with made of 18mm. thick plywood and

1mm. thick laminate on all exposed side.The apron should be made of 18mm. thick plywood and for

elevation 18mm. thick one side BWR ..Plywood patta as shown in drawing and finished with 1mm.

thick laminate. Footrest (0.60 x 0.38) should be made from 18mm. BWR plywood with 1mm laminated

finish in the approved shade. Including all materials and labour etc. complete as per detailed drawing

and instructions of engineer-in-charge.

19 Side Table (1.225x 0.45 x 0.75) Providing and fixing Side Table for 25mm thick (BWR board,) post 1.00 EACH 22500.00

forming laminated top with 6mm thick BWR plywood at backside finished with 1mm. thick approved

laminate, made out of 18mm thick BWR plywood with exterior side 1mm. and interior side 0.6mm.

Approved laminate. Drawer unit box (measurement shown in drawing) with wooden bedding

patti/PVC, lock and telescopic channel. Key board tray will be made of 18mm. thick post foamed BWR

plywood with telescopic chanel. Shutter will be made of 18mm. thick post forming BWR with magnet,

multiple drawer lock, S.S. legs (75mm height) in bottom, auto hinges of HAFELE or equivalent.

Including all materials and labour etc. complete as per detailed drawing and instructions of engineer-

Linear / Running Counter For Work Station.Providing and Fixing Linear / Running Counters of 4' Wide

width 2' made up of 18 mm thick Plywood. The table top shall be finished with 1 mm thick laminate of

approved make and the edge shall be finished with 12 mm wooden bidding duly finished in polish /

duco paint to match with the laminate of the table top. Providing & Supplying Work Station Between

Glass Partition Soft Board.The table shall be provided with drawer pedestal unit made up of 18 mm

thick MR ply and drawers shall be running on approved make EBCO / Hettich / Haffele make telescopic

channels. The handle lock etc. shall be of the similar make. The workstation also shall be provided with

each of key board tray, CPU trolley and foot rest of EBCO / Innofitt make as per the instructions of

Engineer-in-charge / Architects.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Low Height/ Full Height Storage - Providing, Supplying & Fixing Basic Str. in 19 mm Ply wood, Outer

Side 1 mm Laminate in position for Storage and Inner 0.5 yo 0.6 mm Laminate of washable type

material of good quality with appropriate adhesive of approved quality like fevicol or its equivalent

21 brands with smooth finishing and in line level with regular edges as per Arch./ EIC Instruction incl. 3.00 SQMT 9000.00

cutting and any necessary cut outs of Storage & Door if any required etc comp. in all respects. All rates

are inclusive of hardware like, nails, screws,abro taps, Lock , Handle , Auto hinge , adhesive etc.

GLASS DOOR: Providing and fixing in position full height 12mm thick toughened glass STL45 Door

System with 6063-T6 grade duly Anodized Aluminium Sections having sizes of 45x55x1.5mm thick,

mm Toughened Glass including Assa Abloy Door Closure /Floor Spring , Hinges, SS Handle (H Type

450mm), SS Bottom Lock, Thermoplastic Gaskets & Screw Caps all necessary hardware of as per

22 approved make by Architect. 10mm thick Saint Gobain make customized clear toughened glass.Work 11 SQMT 5880.00

complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, all

leads ,accessories, sample mockup, all floor , all levels, all heights , necessary frame work,Scafffolding

etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

MANAGER CABIN MAIN CHAIR Adj. Arms Larger Seats seat size: 47.0 cm. (w) x 51.5 cm. (d) back size

:45.0 cm. (w) x 65.3 cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should be

moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. armrests : the

armrests have an up-down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure.

armrest top has an integrated layer of thermoplastic elastomer (tpe).

lumbar support assembly: the lumbar support consshould be ts of polypropylene pad with moulded

polyurethane foam & covered with polyester fabric. the height of lumbar pad can be adjusted through

two projecting knobs provided on the rear side of the pad. lumbar pad has an adjustment of 8.0 ±

front pivot synchro mechanism: the adjustable tilting mechanism should be designed with the

following features.

23 • 360° revolving type. 1 EACH 15000.00

• single point control.

• front-pivot for tilt with feet resting on ground ensuring more comfort.

• tilt tension adjustment.

• 4-position locking with anti-shock feature.

• seat/back tilting ratio of 1:2.

pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ±

pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted

with 5 nos. twin wheel castors. the pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm.

with castors).twin wheel castors: the twin wheel castors should be injection moulded in black

nylon.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE:

Staff Chair the seat should be made up of 1.2 ±0.1cm. thick hot-pressed

plywood , upholstered with fabric upholstery covers and moulded polyurethane foam.

seat size: 47.0 cm. (w) x 48.0 cm. (d)back : the back asembly. should be made of powder coated (oft 40-

60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with

contoured lumbar support for extra comfort. the back should be upholstered using double layer

spacer mesh fabric with high tenacity yarn.

back size : 46.5 cm (w) x 60.5 cm (h)high resilience (hr) polyurethane foam: the hr polyurethane foam

should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25%

compression.armrests: the one-piece armrests should be injection moulded from black co-polymer

polypropylene. Centre-tilt mechanism: the mechashould be m should be designed with the following

24 • 360° revolving type. 5 EACH 8700.00

• 17° ±2° maximum tilt on pivot at centre

• upright position locking.

tilt tension adjustment. .pneumatic height adjustment: the pneumatic height adjustment has an

adjustment stroke of 11.0 ±0.3cm.elescopic bellow assy: the bellow should be 3 piece telescopic type

and injection moulded in black polypropylene.pedestal .: the pedestal should be injection moulded in

black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be

±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)twin wheel castors: the twin wheel castors should

be injection moulded in black nylon.Overall Dimensions of Chair-Seat Height - min 43.3 to max

Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm

and Depth-76.3 cm.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

25 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 1 EACH 19000.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts.

Providing & Fixing Cushionon Seating & Back as per Instruction. The Shell to be assembled on the cross

beam with help of M8 Bolts.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

26 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 17500.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

GYPSUM BOARD CELLING : Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender

channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making

necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

595 x 595 MM CELLING:Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light

weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 1200X600mm and secondary

28 cross ’T’ of length 600mm and size600mm centre to centre to form agrid of 24x28mm made of 0.30 39 SQMT 1632.63

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre

to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges

light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the

grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to

centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyester

baked paint, for all heights, as per specifications, drawings and as directed by engineer-incharge. Note:-

Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made

SS plate Signage: 450mm X 100mm - Stainless Steel satin finished flat etching plate of 1.5mm thick.

Providing Making and fixing of various in-door signage, as & where basis. sign in ISI Brushed S.S. Grade

304 letters in English letter + All text and design in acid process, each plates. Each text & design with

respective color coated complete plate. The SS mounted on glass or any non holes surfaced by 3M

29 double sided tape with required chemical process, guidelines by 3M company. Whereas, Any other 5 EACH 1800.00

then glass surface, SS plate mounted by Two side screws with required grips nd holes on the wall with

two SS spacer screws. The item should be as per instruction at site approved by Architect of Engineer

in charge. The rate shall be inclusive of scaffolding, drilling, adhesive material etc. at all height.

Providing & Arranging wheel chair for physically handicapped person having dimension 790(L) x

600(W) x 700(H)mm. With foldable frame structure made of carbon steel setcion 22mm x 1.2mm or as

per direction of engineer in charge. A3 carbon sheet with chrome finish cross bars made of A3 carbon

steel material with setcion 25.4mm x 1.2mm., 24 inch solid mag wheels with alloy in the rim, hand rim

of setcion 16mm x 1.2mm. carbon steel with chrome finish, front wheel of 8 inch HUB made of PA

30 polymer & outer side of solid rubber PU moulded arm rest & base made of ABS, leather finish calf rest 1 EACH 13570.00

& seat with cushion alluminium foot rest with updown movement having extended base foot press

with moulded plastic including hand brakes & full structure is anti rust chrome finish with users

capacity of 100 kg including all necessary fixture, fastners, fittings, labour, material, machinary etc.

complete as seletced and diretced by Engineer-in-charge.

Providing & fixing S.S. Pipe railing of 50mm dia pipe not less than 18guage, in 3 rows supported by S.S.

Pipe of 50mm dia at every corners & 1.5 mt C/C incl. concrete block (0.35 X 0.35 X 0.35) incl. 16 guage

S.S. sheet using required cutting, jointing, welding, threading, drilling & fixing etc. comp. as directed as

per drawing (For Platform)

Providing & Fixing Shelf Adhesive Tractile Tiles as per Architect/ GRIMCO manager Instruction. The

Tiles shall be Fixed with Suitable Adhesive Material with All required Additional Hardware Suppot.

Rate shall be Including Transportation , All Floor , Hardware, Adhesive Material etc.

Fixing Ipsa Super Strong Handsfree Foot Operated Pull (304 s.s)door latches of sizes 100mm with

necessary screws etc. complete

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Painting lines, dashes, arrows, letters etc on roads, Air- fields and like in two coats with road marking

paint, brushing including cleaning the surface of all dirt, dust and other foreign matter (ii) over

Providing and fixing required size Stainless steel plate of 1.0mm thickness with regular

printed signage at top in black colour at top part of plate and respective brialle lipi

sgnages at bottom part the plate, S.S. Plate to be fixed on 10mm thick clear acrylic

sheet, this whole assembly to be fixed on wall with four numbers of SS studs etc

complete as per instructions of engineer in-charge.

DEDO WORK (600X600 mm):'Providing & laying Antiskid Vitrified 12mm thick tiles flooring, treads of

steps and landing laid on bed of 20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface and jointed with colour cement slurry including finished with flush pointing &

36 cleaning the surface etc. completed of any Shade and approved by Higher Authority of approved 40.00 SQMT 1446.99

brands & Size. Providing & Applying spacer of 5mm and not less than 4mm depth of epoxy grooving of

levirate , Ruff equivalents as per detailed drawing and as directed by Grimco Manager /Architect. Basic

Cost of Tiles is Rs 50/-sqft

Scraping of old paint/ distemper wherever necessary from the existing walls, and applying of 4.0 to

37 mm thick lime over it to give a smooth leveled finish, the final coat to have one coat of oil based 131.00 SQMT 255.00

Cement primer the cost shall include all labor , materials, etc complete.

Providing & fixing 18mm thick cement sheet/18 mm Plywood for panelling work with Selected Colour

as per approved by Architect/Client. The rate shall be for all floors, at all heights, all shapes including

CNC / Engraving and all costs.

The frame work shall be made from square hollow aluminum anodized section size of 50x50x1.5 mm

& 25x50x1.5 mm of approved make conforming to IS code. The framework shall be fixed as per

drawing vertically @ 600 mm c/c & horizontal 600 mm c/c horizontally. which shall be provided from

gr. level to RCC slab / beams soffit level. Rates shall also be inclusive of cost of making CNC/engraving

/cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing

38 additional sections for strengthening around the openings/cutouts additional support for fixing of 8.00 SQMT 4500.00

patch fittings for doors, making grooves between wall & board, in filled with termite treated members

if required or as per drawing /instruction of EIC. All curved surfaces, recesses, waffles shall be part of

the paneling including Openable shutter wherever required area and finished with the same material.

Work complete including all type of material, fittings , fixtures, Finish, loading , unloading

transportation, all leads ,accessories, groove, adhesive ,tape, headless nails, sample mockup, all floor

all levels, all heights etc complete as per detailed drawings ,specifications & instruction of

Client/EIC.sample mock shall be approved from as per Architect/GRIMCO Manager &instruction.

Providing and fixing wooden Palmet of up to 50 to 150 mm Thick L shape made & 300 mm Height of

12mm thick ply with 4 mm thick mdf with colour as per IS 710 and beading of 4mm thick and 25mm

wide Ghana Teak wood for projection screen. Rates shall also be inclusive of cost of making

CNC/engraving /cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers

etc & providing additional sections for strengthening around the openings/cutouts additional support

for fixing of patch fittings for doors, making grooves between wall & board, in filled with termite

treated members if required or as per drawing /instruction of EIC. Rate to be inclusive of lipping,

cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and

for all floors as per drawing and approved sample etc should also take load of all the all roller blinds

as per Architect/GRIMCO Manager instruction.

Providing wood work in frames of Doors, windows cleare story windows and other similar works

wrought,frame and fixed in position including both Side 100 mm wide Panelling with Selected

Laminate. Providing & Fixing 12 mm Thick Plywood With Selected Laminate for Panelling . Rate Shall

be including Anodized aluminum fixtures & fastenings ,Adhesive Material ,& Necessary Hardware. the

Measurement shall be Consider Running Length X Width as directed by engineer in charge.

Providing & Fixing Wooden Partition with 10 mm Glass framing in Alluminium with both side cover

with 12mm thick comm. ply finished both Side with 1.0mm thick selected laminate, without any air

gap and grooving as per design& instruction of the EIC/Architect. wooden framing to be erected

above false ceiling make hole/face plate for conduit pipes of electrical / networking cables with

openable stud from partition Including all materials and labour etc. Open edges also finish with

laminate.Providing & Fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and

fixing full height glass partition made out of glazed partition with stanless steel U channel profile in the

top and Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The

glass to be butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between

two butt jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled

with clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved by

the Architect. including hardware.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

supplying & fixing 3m sparkle film/Fluted Film on glass with manufacturer specification, as per the

42 detailed technical specifications, drawings and as per Architect/GRIMCO Manager instruction. 18.00 SQMT 1200.00

Deep Cleaning Glass, Wall,Window ,Table with Require Material Broom,Dust Pan,Squeegee,Sprey

Cleaner,Mop as per Instruction of the Grimco Manager/Architect.

Providing and fixing Roller Blind fixed on window level on wooden batten and curtain lift with cotton

thin rope, design and colour as per instruction by engineer – in – Charge with necessary hardware

fitting, material and labour etc. complete as per detail drawing and instruction of engineer-in charge

and consultant.

Providing and fixing ACP Letters for Office Detail Name & addres Letters on ACP

fascia.Providing 3mm thick alluminium composite panel (ACP) sheet fascia and all side with

required iron angle / hollow heavy pipe structure frame. and back side cover up by aliminium

sheet ,complete box should be water-proof.and make it . Approx size of the Signages is

:5'X2'0"X0'5".Outdoor signage: 5 to 6 mm thick & ACP Letters / logo signage Complete as per

EIC/Architect Instruction.

Providing and Fixing Doormat (6' X 2') made up of synthetic material as per the approval from the

Architect / EIC.

Providing and Fixing Doormat ( Approx 1.5' X 2') made up of synthetic material as per the approval

from the Architect / EIC.

Providig & Fixing Wall Clock as per approved make. As per instruction at site approved by Architect of

Engineer in charge.

Providing, supplying SS 304 perforated Dustbin/ Wire mesh Dustbin as per approved make. As per

instruction at site approved by Architect of Engineer in charge.

Supplying labour for removing and filling all type Civil /Electrical HVAC of Debric incl. construction

50 waste materials and cleaning or any other type work for 8 hr. per day comp. as directed by eng. 9.00 EACH 1650.00

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with

51 textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with 20.00 Pt. 445.00

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single

52 mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / 8.00 Pt. 632.00

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type

53 of accessories. 8.00 Pt. 471.00

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling completeCat-III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type accessories. Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(9) 16 Amp. SP one way switch Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green)

both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below

type of pipe with 6A Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

57 modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or 2.00 Pt. 562.00

ceiling rose or H.D.Connector as directed.ss will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be

erected complete with earth continuity and necessary connection with primary light with accessories

erected on Metal / PVC / wooden box covered covered with appropriate front plate modules erected

on / in wall / ceiling for open / concealed wiring. with necessary Lamp holder / ceiling rose /

H.D.Connector as directed.as per pipe erected with following type of accessories.Note:- Maximum up

to 6 mtrs length, excess will be considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat-

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories cat iii

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat-III

(4) TV Co-axial Socket outlet

(7) Blank Plate Single

(8) Modem Jack for Computer Open RJ-45

64 (19) Modular Indicating Call Bell Cat.III 1.00 EA 326.00

65 (20) Modular Buzzer Cat.III 1.00 EA 148.00

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

66 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 225.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

69 Check-nuts etc. complete of following sizes. 105.00 Mtr. 17.00

Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement

with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin

71 polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall / ceiling of following size . 50.00 Mtr. 31.00

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS with necessary end caps Internal and

72 external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following sizes 55.00 Mtr. 187.00

(3) 50 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

73 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 425.00 Mtr. 101.00

(a) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size

(a) 2 wire 4 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly -

75 Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. 105.00 Mtr. 39.00

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE

insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR

outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following

76 size of conductors & nos.of pairs. With necessary connections. 325.00 Mtr. 20.00

A. Conductor Size 0.5 mm

(a) (2) Unarmoured

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

Providing & erecting main Distribution (MDF) indoor type, back mounted frame

(a) Suitable for 10 pair

ARMOURED ALLUMINIUM CABLES.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

79 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 10.00 Mtr. 152.00

d) 4 Core 16 Sq.mm.

80 c) 4 Core 10 Sq.mm. 50.00 Mtr. 139.00

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

81 armoured cable complete with out going tails, insulating tape etc for following size of cables. 2.00 Nos 38.00

(C) 2 to 4 core 10 Sq. mm

82 d) 2 to 4 Core 16 Sq.mm 2.00 Nos 47.00

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly

83 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut 8.00 Nos 13.00

bolts in an approved manner.

Providing and fixing printed instruction chart both in English and Gujarati and duly framed with front

85 glasses, for treatment of person suffering from Electric shock with minimum 50" diagonally size. 1.00 Nos 129.00

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

86 clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. 4.00 Ea 6526.00

[A] For 4.5 Kg Capacity

MINIATURE CIRCUIT BREAKERS.

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having

87 breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 10.00 Nos 111.00

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking

88 capacity & confirms to IS : 8828 in existing box having following capacity 1.00 Nos 276.00

(A) 6 to 32 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breaking

89 capacity & confirms to IS :8828 in existing box having following capacity 2.00 Nos 632.00

(b)40 Amp. Cat.III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

90 be used) 1.00 Nos 2885.00

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door

EARTH LEAKAGE CIRCUIT BREAKERS.

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz.

91 having characteristic of quick action & tripping with all advance feature & do not incorporate any 3.00 Nos 2213.00

electronic component. for following Max. rating erected as directed

(ii) 40Amps. DP

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

CEILING FANS AND ACCESSORIS.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI

92 mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium 7.00 Nos 1929.00

blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in

FAN ACCESSORIES.

93 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly 1.00 Mtr. 107.00

painted for fan complete with necessary 24/ O.2, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Roundbar grouted in RCC slab with Making the site as

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

95 length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected 1.00 Nos 107.00

concealed in Ceiling with necessary finishing..

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with

necessary hook of 10 mm M.S. Round Bar.

97 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 1.00 Nos 18.00

TABLE FANS, EXHAUST FANS & ACCESSORIES.

98 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 1.00 Nos 1687.00

RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

99 Luminaire efficiency> 85 lumens/watt , 2.00 Nos 370.00

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)

(A) Tube Light with integral/ non-integral driver

(d) 22-24 Watts, Surge - 4KV,IP-20, 4 feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaire efficiency> 85 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates)Square/ Circular Surface/Recessed Mounted

Downlight/Hanging with provision for spring loaded mounting clips complete.(b)16-20 watts, Surge-4

101 Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ 2.00 Kg. 77.00

Transformer LT panel board, Motors etc. using proper clamp.

102 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 2.00 kg 787.00

Removing all Electrical Material / equipment from existing set up , also handover to client

representative as per them requirement

104 Re use the electrical material as per Client's epresentative / architect team 's instruction 1.00 job 5000.00

Supplying and erecting Of 43 " UHD LED display for CCTV monitoring and checking .(the scope

includw the stand and other necessary accessasory to coplete the job .

Supplying & Erecting floor mounted/ table top single phase 50Hz water dispenser with SS

food grade cold tank specification having three water tap of hot/cold/ambient water function,

106 LED display with storage capacity from 2.5 Ltrs to 3.2 Ltrs, cooling capacity 2.5ltrs/hr, including 1.00 Ea. 11443.00

refrigerant with 20ltrs refrigerant storage capacity compartment inclusive 1No.water topping

Conduits & Pipes

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

107 on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution 200.00 Mtr. 24.00

& Clamps with following dia of pipes, in approved manner as directed

(8) Modem Jack for Computer Open RJ-45

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MAHUDHA.

Sr. No. Description Quantity Unit Rate Amount

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

110 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 1.00 no 47780.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.

(B) for 1.5 ton capacity - Premium Cat.

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with

111 accessories etc. duly connected separately erected evaporating unit and blower motor with its 1.00 no 60245.00

accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star

and above of current year) with necessary core cutting.for 2 ton capacity

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately erected evaporating unit and blower motor with its

112 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( 1.00 no 37983.00

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.[A] For 1 Ton Capacity Premium Cat.

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR

capacity erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and

control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Providing & Fixing 100X100 mm PVC Casing Patti for Drain Pipe/Electrical as per Architect/Grimco

Manager Instruction.

Misc.Civil Work Like Wall Jury,Cut Out & Opening to pass Piping Tray,wire ,pipes & Drain Pipes

116 Including with Refinishing & Plastering of the Same to the Original Finish. 1.00 JOB WORK 9500.00

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MANDAL.

Sr. No. Description Quantity Unit Rate Amount

Removing/Shifting existing TW partitions/Panelling/Curtain/Furniture including

hardware/Civil/Sanitary/Piping Work etc including stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift and the site shall be cleaned as directed by EIC. Care shall

be taken to remove the partition / door so as to reuse the same.

Removing Ac,OutDoor & Accessories and Handover the Client as per Architect/Grimco Manager

Instruction. Care shall be taken to remove the AC so as to reuse the same.

CHIPPING CONCRETE WORK :Chipping of unsound weak concrete material from slab, beam, column

and around the reinforcement incl. plaster etc. with manual chiselling with standard power driven

percussion type of pneumatic chisel of standard make as directed by Eng. In Charge incl. tapering all

edges and making square shoulders of cavities etc. comp. and disposal of debris outside the premises

incl. cleaning of exposed reinforcement using approved alkaline chemical rust remover (doctor fix it

rust remover or its equivalent chemical comp. as per manufacturers specification) (Area of RCC

surface is to be measured for payment) etc. incl applying 10 to 15 mm avg. thick plaster in C.M. (1:3)

incl. curing, scaffolding, curing, Existing Removing & Scrape Plaster etc. comp. as directed by Grimco

Manager /Architect.

MASONARY WORK: Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement :4 -coarse sand) in

(Conventional) Rate Shall Be Consider All Floor & Work Shall be Execute as per Architect

Grimco Manager Instruction.

Providing Brick masonary using common burnt clay building bricks for foundation and plinth

having crushing strength not less than 35 kg./ Sq. Cm. in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) incl. watering,curing,scaffolding and racking out joints etc. comp as per directed by

PLASTER WORK : Providing 15mm thik. Cement plaster in single coat on Internal Walls for interior

6 plastering of following finished even and smooth in Cement Mortar 1:3 (1-Cement : 3-Sand) incl. 27.00 SQMT 203.34

finishing with a floating coat of neat cement slurry.

FLOORING: Providing and Laying Glossy/mat Finished vitrified tiles of size 800 X 800mm and 8 mm to

10mm thick of approved make and colour having homogeneous materials in flooring laid on 20mm

thick average cement mortar 1:3 (1 cement: 3 coarse sand)as directed by Engineer in charge. Applying

spacer of 4mm and not less than 2mm depth of epoxy grooving of lavicrete , Roff equivalents directed

by Engineer in charge. incl. cost of fixing materials, labour, tools, plants, equipotent incl. all lead & lift

Supplying & fixing heavy duty 800 X 800 mm Vitrified tiles of 8 to 9 mm the of Approved Brand in

Skirting as per approved pattern ,Match Shade with Existing Flooring & design laid over neat cement

slurry & cement mortar in (1:6) bedding 20 mm the average & joint with colour cement slurry incl.

special cornices, corners or angles, tiles etc. incl.Applying spacer of 4mm and not less than 2mm depth

of epoxy grooving of lavicrete , Roff equivalentas directed by Engineer in charge. incl. cost of fixing

materials,labour, tools, plants, equiptnent incl. all lead & lift comp, labour, tools, plants, equipmens

incl. all lead & lift comp. as directed by Architect /EIC .

Removing & Refixing Grill as per Architect /Grimco Manager Instruction Rate Shall be Including

9 Loading,Unloading,Labour,Welding,Hardware etc.Care shall be taken to remove the Grill so as to reuse 3.00 EACH 500.00

Providing & Fixing window having extruded aluminium colour anodized section frame main outer size

63.5 x38.1x1.95mm(Jindal or Hindalco section No.4605 @ Wt.1.094 Kg/Rmt) horizontal Two Track

member size 61.85x31.75x1.2mm(of Jindal or Hindalco section No.8687 @ Wt.of 0.695 Kg/mt.)

vertical member of size 61.85x 31.75x1.3mm (of Jindal or Hindalco section No. 8758 @ wt of

Kg/Mt.) with Sluiding shutter of horizontal member size 40x18x1.29mm (of Jindal or Hindalco section

No. 8949 @ wt.of 0.456 kg/mt.) vertical member of size 40x18x1.29mm (of jindal or Hindalco section

No.8947 @ wt.of 0.456 Kg/ mt./section 8948 @ wt of 0.457 kg/mt.) with 5mm thick transperant

bronze colour tinted float glass with colour anodized aluminium fittings & fixtures with transparent

silicon sealant glass fixing to frame as per detail .

applying primer coat of the paint, Putty shall be applying walls and ceiling for making even surface up

to finish level.Providing and applying even coats of acrylic emulsion paint / on walls and ceiling up to

final finish. Shade and texture of the paint shall be as approved by Architect or EIC. Application of

paint shall be with brush and last coat of paint shall be applied with a standard company roller all as

approved by architect/Grimco Manager.rates are inclusive cost of paint, putty, primer, brush,

roller,Removing Existing Paint, scaffolding cleaning charges etc. complete.

Providing and applying synthetic enamel paint (and Repair Grill/M.s. as per Site Situation-Proper

Finishing , Levelling,Welding, Cleaning) of Asian/Nerolac/ICI/Lewis Berger/J&N of approved brand to

12 previously painted steel work with one coat of approved quality and brand paint of Asian, Nerolac, ICI, 11.00 SQMT 250.00

Berger, Johnson make and of required shade, including cleaning and scrapping the surface with sand

paper etc. complete as directed.

FALSE FLOORING (Stage) Providing & Fixing ms Structure Vertical Stand 50X50X5 mm 600 X

mm center to Center Distance with Anticorrosive Paint and above Stand 25 X 25X5 mm square Hollow

13 Pipe With Anticorrissive Paint by Steel Welded Construction. Outer All Exposed Part Shall be Fitted 6.00 SQMT 7000.00

Square Hollow Pipe & 18 mm Plywood With Laminate with Adhesive Material , Nail Scrue Abro tap Etc

all Required Hardware.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MANDAL.

Sr. No. Description Quantity Unit Rate Amount

FULL HEIGHT /LOW HEIGHT PARTITION (FULLY SOLID) (75mm thk.) Providing and fixing full height /

half height double skin wooden partition upto ceiling or beam bottom as per drawing and framing in

Alluminium with both side cover with 12mm thick comm. ply finished both Side with 1.0mm thick

selected laminate, without any air gap and grooving as per design& instruction of the EIC/Architect.

14 wooden framing to be erected above false ceiling make hole/face plate for conduit pipes of electrical / 32.00 SQMT 5200.00

networking cables with openable stud from partition Including all materials and labour etc. Open

edges also finish with laminate. complete as per detail drawing and instruction of Architect/engineer-

Providing and fixing of full /Partly glazed 10 mm thk toughed glass partition, Providing and fixing full

height glass partition made out of glazed partition with stanless steel U channel profile in the top and

Bottom with 10mm thick clear toughened glass fixing with wooden bedding filled with The glass to be

butt jointed with 2 to 3 mm edge chamfer and edge polishing all around. Distance between two butt

15 jointed glass panels not to exceed 4mm. Edges and grooves between glass panels to be filled with 3.00 SQMT 4800.00

clear silicon sealant of approved make neatly applied as indicated in the drawing.Rate Shall be

Including Glass Cutting ,Trasportation with Require All Types Hardware as per the sample approved

by the Architect. including hardware.

Providing and fixing 35 mm thick Decorative type Water proof flush door shutters, solid core

construction with wood frame with Polish of ground class hard-wood with cross band and face ply-

wood face panels, 1.0 mm thick laminate on both sides including the top Portion ( Aprox 0.380mm

Height ) Pack With Transperent Glass With Ply Frame, Stainless steel fixtures and fastening like

,Handle,Lock , stopper including for door shutters sides etc complete. as directed by engineer in

Door Laminate Change. To be Removed & Refixing .Providing and Fixing Both Side 1 mm laminate &

Existing Removing Laminate Door of washable type material of good quality with appropriate

adhesive of approved quality like fevicol or its equivalent brands with smooth finishing and in line level

with regular edges as per requirement and site situation incl. cutting and any necessary cut outs of

Glass and Cutout Finish With Plywood With Selected Laminate & Door if any required etc. comp. in all

respects. All rates are inclusive of hardware like, nails, screws, abro taps, adhesive etc. complete.

Providing ,Removing Existing Door Closer and fixing Door Closer and Blue Space GPRH Solid Standoffs

18 Heavy-Duty Commercial Grade-304 Stainless Steel Push Pull Door Handle as per Architect & EIC 5.00 EACH 2500.00

Instruction. Rate Shall be Including Fitting Charge.

Table (1.95 x 0.750 x 0.75) Providing and fixing the Table with top of 19 mm thick BWR plywood&

Table Top Side Boarder added 19 mm Plywood in Below Side with post formed approved laminate The

side leg should be made of Wood box with laminate. CPU box with made of 18mm. thick plywood and

1mm. thick laminate on all exposed side.The apron should be made of 18mm. thick plywood and for

elevation 18mm. thick one side BWR ..Plywood patta as shown in drawing and finished with 1mm.

thick laminate. Footrest (0.60 x 0.38) should be made from 18mm. BWR plywood with 1mm laminated

finish in the approved shade. Including all materials and labour etc. complete as per detailed drawing

and instructions of engineer-in-charge.

19 Side Table (1.225x 0.45 x 0.75) Providing and fixing Side Table for 25mm thick (BWR board,) post 1.00 EACH 22500.00

forming laminated top with 6mm thick BWR plywood at backside finished with 1mm. thick approved

laminate, made out of 18mm thick BWR plywood with exterior side 1mm. and interior side 0.6mm.

Approved laminate. Drawer unit box (measurement shown in drawing) with wooden bedding

patti/PVC, lock and telescopic channel. Key board tray will be made of 18mm. thick post foamed BWR

plywood with telescopic chanel. Shutter will be made of 18mm. thick post forming BWR with magnet,

multiple drawer lock, S.S. legs (75mm height) in bottom, auto hinges of HAFELE or equivalent.

Including all materials and labour etc. complete as per detailed drawing and instructions of engineer-

Linear / Running Counter For Work Station.Providing and Fixing Linear / Running Counters of 4' Wide

width 2' made up of 18 mm thick Plywood. The table top shall be finished with 1 mm thick laminate of

approved make and the edge shall be finished with 12 mm wooden bidding duly finished in polish /

duco paint to match with the laminate of the table top. Providing & Supplying Work Station Between

Glass Partition Soft Board.The table shall be provided with drawer pedestal unit made up of 18 mm

thick MR ply and drawers shall be running on approved make EBCO / Hettich / Haffele make telescopic

channels. The handle lock etc. shall be of the similar make. The workstation also shall be provided with

each of key board tray, CPU trolley and foot rest of EBCO / Innofitt make as per the instructions of

Engineer-in-charge / Architects.

Low Height/ Full Height Storage - Providing, Supplying & Fixing Basic Str. in 19 mm Ply wood, Outer

Side 1 mm Laminate in position for Storage and Inner 0.5 yo 0.6 mm Laminate of washable type

material of good quality with appropriate adhesive of approved quality like fevicol or its equivalent

21 brands with smooth finishing and in line level with regular edges as per Arch./ EIC Instruction incl. 6.00 SQMT 9000.00

cutting and any necessary cut outs of Storage & Door if any required etc comp. in all respects. All rates

are inclusive of hardware like, nails, screws,abro taps, Lock , Handle , Auto hinge , adhesive etc.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MANDAL.

Sr. No. Description Quantity Unit Rate Amount

GLASS DOOR: Providing and fixing in position full height 12mm thick toughened glass STL45 Door

System with 6063-T6 grade duly Anodized Aluminium Sections having sizes of 45x55x1.5mm thick,

mm Toughened Glass including Assa Abloy Door Closure /Floor Spring , Hinges, SS Handle (H Type

450mm), SS Bottom Lock, Thermoplastic Gaskets & Screw Caps all necessary hardware of as per

22 approved make by Architect. 10mm thick Saint Gobain make customized clear toughened glass.Work 6 SQMT 5880.00

complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, all

leads ,accessories, sample mockup, all floor , all levels, all heights , necessary frame work,Scafffolding

etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

MANAGER CABIN MAIN CHAIR Adj. Arms Larger Seats seat size: 47.0 cm. (w) x 51.5 cm. (d) back size

:45.0 cm. (w) x 65.3 cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should

be moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. armrests : the

armrests have an up-down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure.

armrest top has an integrated layer of thermoplastic elastomer (tpe).

lumbar support assembly: the lumbar support consshould be ts of polypropylene pad with moulded

polyurethane foam & covered with polyester fabric. the height of lumbar pad can be adjusted through

two projecting knobs provided on the rear side of the pad. lumbar pad has an adjustment of 8.0 ±

front pivot synchro mechanism: the adjustable tilting mechanism should be designed with the

following features.

23 • 360° revolving type. 1 EACH 15000.00

• single point control.

• front-pivot for tilt with feet resting on ground ensuring more comfort.

• tilt tension adjustment.

• 4-position locking with anti-shock feature.

• seat/back tilting ratio of 1:2.

pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ±

pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted

with 5 nos. twin wheel castors. the pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm.

with castors).twin wheel castors: the twin wheel castors should be injection moulded in black

nylon.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE:

Staff Chair the seat should be made up of 1.2 ±0.1cm. thick hot-pressed

plywood , upholstered with fabric upholstery covers and moulded polyurethane foam.

seat size: 47.0 cm. (w) x 48.0 cm. (d)back : the back asembly. should be made of powder coated (oft

40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with

contoured lumbar support for extra comfort. the back should be upholstered using double layer

spacer mesh fabric with high tenacity yarn.

back size : 46.5 cm (w) x 60.5 cm (h)high resilience (hr) polyurethane foam: the hr polyurethane foam

should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25%

compression.armrests: the one-piece armrests should be injection moulded from black co-polymer

polypropylene. Centre-tilt mechanism: the mechashould be m should be designed with the following

24 • 360° revolving type. 6 EACH 8700.00

• 17° ±2° maximum tilt on pivot at centre

• upright position locking.

tilt tension adjustment. .pneumatic height adjustment: the pneumatic height adjustment has an

adjustment stroke of 11.0 ±0.3cm.elescopic bellow assy: the bellow should be 3 piece telescopic type

and injection moulded in black polypropylene.pedestal .: the pedestal should be injection moulded in

black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be

±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)twin wheel castors: the twin wheel castors should

be injection moulded in black nylon.Overall Dimensions of Chair-Seat Height - min 43.3 to max 54.3cm.

Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm

and Depth-76.3 cm.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

25 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 2 EACH 19000.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts.

Providing & Fixing Cushionon Seating & Back as per Instruction. The Shell to be assembled on the cross

beam with help of M8 Bolts.

Perforated waiting... Providing and Fixing Three Seater made of black powder coated regular MS

ERW tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/-0.014 cm size. Legs to be chrom plated made

of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold

26 rolled M.S. Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of 4 EACH 17500.00

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/-0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

TENDER FOR CIVIL/INTERIOR/ELECTRICAL/HVAC WORK FOR SUB REGISTRAR OFFICE MANDAL.

Sr. No. Description Quantity Unit Rate Amount

GYPSUM BOARD CELLING : Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender

channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making

necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

595 x 595 MM CELLING:Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light

weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 1200X600mm and secondary

28 cross ’T’ of length 600mm and size600mm centre to centre to form agrid of 24x28mm made of 0.30 47 SQMT 1632.63

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm

centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified

edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in

the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I.

slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners,

4mm G.I. adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm

centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with

polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer-

incharge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No

SS plate Signage: 450mm X 100mm - Stainless Steel satin finished flat etching plate of 1.5mm thick.

Providing Making and fixing of various in-door signage, as & where basis. sign in ISI Brushed S.S. Grade

304 letters in English letter + All text and design in acid process, each plates. Each text & design with

respective color coated complete plate. The SS mounted on glass or any non holes surfaced by 3M