Balance Work of Govt. Senior Secondery School Khuni Tehsil Rampur ,Distt. Shimla

Amount

Providing and fixing ISI marked decorative flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless sqm Steel butt hinges with necessary screws including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing windows of ECO 4000 series having section for external frame should be of 72mmx55mmx 0.58mm thickness section for mullion should be of 72mmx 55mmx0.58mm thickness, section for shutter frame (styel) should be of 47 mmx20mm x0.58mm thickness, section for glass bead should be of 12mmx12mmx0.58 mm thickness and section for fly mesh should be of 40 mmx20mmx0.58mm thickness & section for mesh fixing shoukd be 18mmx6mm x0.58mm thickness. The section of sash bar in openable shutters shall 55mmx20mm x0.58mm (PO 107) each glazed shutter should be provided with one set of S.s. pivot hinges, seccolor make handle with receiver. Each mesh shutter should be provided with one set of pivot hinges, seccolor make handle and latch gaskets made of ethy /propylene diamine (EPDM corner brackets & mullion caps made of nylon/polypropylene. Glazed shutter & fixed glass portions shoukd be provided with glass of 5mm thick glass panel of modi and grills 10mm square M.S. round bar complete as per Arch. drowing and direction including carriage with in all leads and lifts and as per HP.PWD. specifications of 1990 valume lead as per the direction of Engineer in Charge. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16mm including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10mm size. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in?Charge With cement mortar 1:4 (1cement: 4 coarse sand) including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 12mm thick green chalk board(non-magnetic) with superior quality framing specially anodized aluminium profile 20x15mm with corners of specified plastic shall be provided. The board surfacr shall be non-porous ceramic particles on the top screen surface for smooth writing with chalk over 11mm thick particle board which shall have basing material of galvanized steel 28mm thick. The board shall be fixed on the wall with specially designed "J" clamps and square clamps with the help of nylon sleeves and screws as per site requirement complete and as per drawing and instruction of Engineer-in-Charge. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying Full Body vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete: Size of Tile 600x600 mm including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coat including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Big size Orissa Pan No. 2071 of size 580x440 mm of CERA or equivalent including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: Wash basin No.1012 or CERA or equivalent. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm diameter including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :150 mm diameter S.W. pipe including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vetrious china flat back wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern :White Vitreous china Flat Back Large No. 5001 of CERA or equivalent including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vetrious china Division plate of CERA or equivalent of size 90x320x720 mm and including its fittings cutting and making good the walls wherever required including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms :Kent touchless Sanitiser/ Liquid soap Dispenser-1000ml, white. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 115 mm nominal bore, 86 mm long, weighing not less than 88 gms PTMT concealed stop cock with flange of Jaguar and approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45cm length 15 mm nominal bore including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providng and fixing gun metal gate valve with C.I. Wheel of approved quality (screwed end) of 25 mm nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm nominal bore including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing brass ferrule with C.I. mouth coverincluding boring and tapping the main 15 mm nominal bore including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PVC ‘P’ or ‘S’ trap for water closet (squatting pan ) ISI marked including jointing the trap with pan and PVC pipe with approved adhesive etc. complete.110 mm ( one hundred ten millimetre) dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter con- forming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 107 mm long, weighing not less than 110 gms including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing & fixing 100mm dai C.P. gratings of superior quality for floor, gully or nahani trap including carriage of materials within all leads & lifts including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Excavation in foundation trenches etc. in earth work in all kinds of soils such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for:- including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Edges of slabs and breaks in floors and walls in any width. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying in position cement concrete 1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal size)of specified grade excluding the cost of centering and shuttering including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size). including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Reinforced cement concrete work in walls (any thickness),1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size)including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Steel reinforement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement : 3 coarse sand) including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick . including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other ncidentals. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. 110 mm dia (one hundred ten) dia including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

JAI PARKASH