UPGRADATION/ IMPROVEMENT TO VIP-II OFFICERS MESS (P-1) AND SHOPPING COMPLEX (P-95) ,UPGRADATION/ IMPROVEMENT TO TO MES QTRS BLDG NO P-133 AND P-134 AND SPECIAL REPAIR TO BLDG NO P-143 AT AF STN MOUNT ABU, GE(AF) NO 2 JODHPUR

Amount

NOTE:- THIS SCHEDULE CONSISTS OF THREE PARTS. THE RATES OF ITEMS OF SAME NATURE/ DESCRIPTION/ SPECIFICATIONS SHOULD BE QUOTED SAME RATE IN BOQ. ANY VARIATION IN QUOTED RATES IF ANY, LOWEST QUOTED RATE WILL CONSIDERED FOR ACCEPTANCE/ PAYMENT PLEASE.

Demolition of Reinforced cement concrete above ground floors exc 15 cms thickness as in roofs,floors,beams and staircases,landings chajjas and similar suspended works(cutting of reinforcement included in the rate)

Demolition of brickwork /stone masonry / precast articles / jalli built in cement mortar.

Taking down Chowkhats or frames with shutter n. exc 1.5 sq. m (without taking off shutters from the frames) and removing from the site.

Excavating in trenches for hard dense, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out

Removing of excavated material n.exc 50 mtr and depositing where directed at a level n. exc 1.5m above the starting point.

Returning filling in including spreading levelling watering &well ramming in layers n.exc 25 cm in hard/dence soil.

M&L for providing PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete all as specified and directed by Engr-in-charge.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) all as specified and directed by Engr-in-Charge

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter all as specified and directed by Engr-in-Charge

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as specified and directed by Engr-in-Charge

M&L for Reinforced cement concrete M-25 Grade using of 20 mm graded stone aggregate for Foundation,footing and mass concrete complete all as specified and directed by Engr-in-Charge

M&L for Reinforced cement concrete M-25 Grade using of 20 mm graded stone aggregate for Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge

M&L for Reinforced cement concrete M-25 Grade using of 20 mm graded stone aggregate for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge

M&L for Reinforced cement concrete M-25 Grade using of 20 mm graded stone aggregate for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed by Engr-in-Charge

M&L for 10 mm dia and over TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc.

M&L for 6 to 8 mm dia TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc.

M & L brick work using sub class 'B' bricks curved or straight in plan exc 6 mtr mean radius in CM (1:6) complete all as specified and directed by Engr-in-Charge

Earth filling under floors in layers n exc 25 cm thick spreading & levelling including well ramming complete all as specified and directed.

M & L for hard core broken stone or builders of gauge not exceeding 63mm, deposited, spread and leveled in layer not exceeding 20 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick PCC 1:2 :4 type B-2 using 20mm graded stone aggregate as in flooring and Finishing cement concrete surface even and smooth using of with out extra cement complete all as specified and directed by Engr-in-charge.

M & L for PCC 1:2:4 type B1 using of 20 mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not proivded for in Item 4028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed by Engr-in-Charge

M&L 15 mm thick rendering in cm 1:4 on brick surfaces finished even and smooth without using extra cement incl mixing of WPC as per manufactrer instructioncomplete all as specified and directed by Engr-in-Charge

M&L 10 mm thick rendering in cm 1:4 on on ceiling surfaces finished even and smooth without using extra cement incl mixing of WPC as per manufactrer instruction complete all as specified and directed by Engr-in-Charge

Supply only liquid water proofing compound

M&L for preperation of new plastered surfaces and applying two coats of oil bound distemper on walls over a coat of 3 mm thick wall care putty all as specified. (Note - work shall be got executed through skilled representative of manufacture company)

M & L for two coats of pastic emulsion exterior paint in over a coat of primer complete all as specified & directerd.

M&L for 600mmx600mmx10 mm thick vetrified Light shade ceramic tiles shade as approved flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and directed.

S&F false ceiling with 16 mm thick glass fibre reinforced Gypsum ceiling tiles of size 595 X 595 mm ,prima fine fissured micro look white coloured using Aluminium powder coated “T” section 25 X16X1.5mm thickness grid and 6 mm dia GI suspension wire etc complete all as specified. Make-Diamond or Equivalent.

S&F aluminium anodised frame for doors, windows,partitions powder coated (min thickness 50 microns) complete all as specifed and directed

S&F Aluminium anodised powder coated window shutter, fixed type without sash bar, alumn section section weighing 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F tinted glass pane 5.5mm thick area of each pane exc 0.5 sqm fixed with beads and metal clips/pins

S&F Aluminium doors shutters air tight with natural anodized alunimium frame with on or more rebate partly glazed and partly panelled of with hollow profile PVC panelling of thickness 12mm (all aluminium member Top, bootom, vertical & middle of shutter made of size 82.55x44.45x1.80mm thick including necessary jointing cleats, glazing clips, 5mm thick tinted glass, rubber packing with anodized aluminium beading /glazing clip size 19.00x17.30x0.70mm, wt 0.097 Kg/RM of both side and fixing aluminium fittings i.e aluminium hinges 100mm three numbers, handles 200mm long two numbers, tower bolts 150mm two numbers and mortic lock with 06 lever fitting shoiuld be ISI marked complete in all respect as engr-in-Charge. (Rates will also include making good floor /wall jambs of doors/ windows surface with plaster and match with existing finishes) Make of aluminium : hindalco, Jindal, Indalco.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified & directed.

M&L glazed ceramic coloured tiles in vertical surfaces 350x250x7mm /450x350x7mm thick set and jointed in neat cement slurry and pointed in white / colour cement to match over and including 15 mm thick screed bed cement mortar in CM 1:4 complete all as specified

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types nd including 20mm thick screed bed in CM 1:4 complete all as directed by Engineer-in-Charge.

M/L for Screed bed or bedding layer of cement mortar 15 mm thick for laying floors finishes in cement mortar 1:6 complete all as specified and directed

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

Taking down Chowkhats or frames with shutter exc 1.5 sq. m and n.exc 4 Sqm (without taking off shutters from the frames) and removing from the site.

S & F Factory made Solid PVC door frame of size 50 x 47 mm , made out of 5mm plain coloured PVC sheet reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and making good the disturbed surfaces with plastering in CM 1:6 and the rate quoted is inclusive this element, noting extra shall be paid on this account complete all as specified.

S & F 30mm thick factory made PVC solid panel PVC door, shutter conforming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15 x15mm for top & bottom rails, MS frame shall have a coat of red oxide primer of approved make and shall 'be covered with 5mm thick heat moulded PVC 'C' channel of size 30x50mm forming styles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mmx2)thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with 30mm wide x 5mm thick PVC sheet beading on either side and jointed together with solvent cement adhesive and an additional 5mm thick PVC strip of 20mm width is to be struck on the interior side of 'C' Channel using PVC solvent adhesive complete as per manufacture’s specifications & drawings, all as directed by Engineer-in-Charge.

S& F mild steel medium weight Butt Hinges 100mm long and fixed with steel screws complete all as specified.

S&F aluminium handles, cast type, anodised 150 mm long all as specified and directed by Engineer-in charge.

S&F Aluminium, anodised, barrel tower bolts of extruded section150mm long stove enameled blck with bright bolt

S&F aluminium alloy anodized sliding door bolts with hasp and staple (bolt type and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long all as specified

S&F aluminium anodized barrel tower bolts of extruded section 100 mm long all as specified

M&L for machine cut kota stone slab flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 20mm thick screed bed in CM 1:4 complete all as directed by Engineer-in-Charge.

S & F Tubular towel rail, 20mm dia, D type, 60 cm long between flanges CP brass.

S&F in repair vitreous china EWC with 10 litre capacity flush tank (Twin flush) monolathic with WC, coloured including coloured PVC hydraulic seat cover fixing bolt, necessary cutting diversion, opening in wall & floor etc complete as directed of approved/ standard quality. Make –Jaquar CAT No ITS -WHT-89851S300PP or equivalent.

S & F in repair Vitreous Arc type Wash hand basin white, size 575 x 430 mm size (Arc type) including cutting for and pinning ends of brackets or erecting stand and 32 or 40 mm dia of waste coupling of PTMT (half or full threaded) with waste pipe. Make –Jaquar CAT No ACS-WHT-87901 or equivalent.

S & F Vitreous China urinals, bowl type of size 370X315X620Mm (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) Make –Jaquar CAT NoURC-WHT-132530 or equivalent.

S & F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed.Make –Jaquar CAT NoFLR-5281N or equivalent.

S & F PVC Low level flushing cistren 10 Ltr capacety including all itting such as flush pipe brackets .

S & F in repair bib tap brass 15mm dia cost copper alloy with butter fly handle CP fancy type.

S & F in repair 15mm chromium plated swivel shower rose with or without swivel joints sny size for fixing with 15 mm pipe incl shower arm 15 mm size , 195 mm long with bend of 45 degree.

S/F in repairs 15 mm angle valve chromium plated with wall flange and fancy type with high pressure screwed down and with CP flange of same make complete all as specified and directed of Make- Jaquar or Equvlent.

S & F in repair hand spray (Health faucet) 1 mtr PVC tube 15 mm bore with wall hook (CP) make : Jaguar or equal make fixed in repairs

S & F in repair 15mm dia stop valve CP screwed to unioun or GI pipe etc.

S & F in repair GI water tubes medium grade 15mm in walls or laid in floors including all fittings all as specified and directed by Engr - in - Charge.

S & F in repair for 20mm dia GI tubing med grade fixed to wall or laid in floor including all fittings all as specified and directed by Engr - in - Charge..

S&F Cast iron Nahani trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F cast iron bends (any) radius of 75 mm bore.

S&F 110mm PVC connections short connections bent type

S&F 110mm PVC Bends any radius

S&F PVC (SWR) multi floor trap 75 mm size with grating including jointing with solvent cement .

S&F Grating square 150mm size of PTMT(Minimum weight 100 gms) complete all as specified.

S&F Cast iron soil, waste and vent pipes 75 mm bore, in any length with or without ears with cement joints, laid in trenches or in floors all as specified and directed By Engr-in-Charge.

S&F Cast iron soil, waste and vent pipes 75 mm bore, in any length with or without ears with cement joints, laid in trenches or in floorsincluding all acessories fittings all as specified and directed By Engr-in-Charge.

S&F CI Bends (any radius) 100 mm bore, diminishing pieces or tapers (larger bore measured) complete all as specified.

S&F CI Bends (any radius) 75 mm bore, diminishing pieces or tapers (larger bore measured) complete all as specified.

S&F CI Branch pieces 100 mm bore, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

S&F CI Branch pieces 75 mm bore, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

S & F in repair pillar cock 15mm dia CP fency type complete all as specified and directed by Engr-in-Charge.

S&F 32mm waste fittings brass chromimum plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engr-in-Charge.

S&F of Soap dish Vitreous China white, approximate size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws completeall as specified and directed by Engr-in-Charge.

S&F 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balanceing white lamination,fixed with screws to timber frame work, complete all as specified and directed by Engr-in-Charge.

S&F 12mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engr-in-Charge.

Extra over rates of 18/19 mm veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed by Engr-in-Charge.

Extra over rates of 12mm veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed by Engr-in-Charge.

S&F Channel patti for sliding rack (size of channel patti 40 mm wide for fixed portion and 35 mm wide for sliding portion and 1 mm thickness complete all as specified and directed by Engr-in Charge

S&F 75mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint drawers complete all as specified and directed by Engr-in-Charge.

S&F brass dead lock of 75 mm size all as specified by Engr-in-Charge.

M&L for excavating in post holes or similar work each not exceeding 0.5 CUM in hard dense soil getting out and returning filling and ramming including watering etc in layers not exceeding 25 cm all as specified directed by Engr-in-charge

M&L for PCC1:3:6 type C-2 (40mm graded aggregate) as in posts etc all as specified.

S&F joist channel angle, tee section, MS pipe, MS square tube ,Stell trusses as required , MS plate fixed in purlin rafter cleat, support etc incl welding, riveting, J-hook etc conf to Fe-290 Gde E-165 all as directed by Engr-in-charge

M&L preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide.

S&F in repairs fibre glass reinforced translucent plain sheet 2mm thick fixed with L- type or J- type or cranked hook bolts all as specified and directed by Engr-in-Charge.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floor finished complete all as specified.

M& L for rubber moulded cement cnoncrete Chequered tiles 25cm X 25 cm X 25mm thick with coloured cement and white pigment laid over 20 mm thick screed bed or bedding in CM 1:6 in floor finishes complete all as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling or stone flooring including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge

M&L for coloured printed non skid tiles area of each tile exceeding exc 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed with neat cement slurry pointed with colour cement to match the floor, and including 15 mm thick screed bed cement mortar in CM 1:4 complete all as specified (make SOMANY, KAJARIA, MARBITO)

M&L for digital design glazed ceramic tiles in vertical surface of size of each tile 350 x 250 mm and 7 to 8 mm thick fixed to wall with 10 mm thik cement sand mortar in CM 1: 4 , set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed. (make SOMANY, KAJARIA, MARBITO)

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed

M & L for Rubber moulded Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set , jointed and pointed in neat cement slurry in floors with gray cement and pigment with screed bed 15 mm CM 1:6 complete all as specified by Engr- in- Charge

M&L cement concrete 75 mm thick type C-2 1:3:6 ( 40 mm graded agg ) as in plinth protection etc all as directed by Engr in charge .

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings

M&L for galvanised corrugated mild steel sheeting of thickness 0.63 mm with two corrugations side lap,fixed with coach screws and washers in roofs walls etc with grade of zinc coating 275 fixed with L type or J type or cranked hook bolts in lieu of screws

M&L for plain galvanised mild steel sheeting of thickness 0.63 mm as in ridges ,valley gutterswith grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge

Dismantling wall and ceiling boards( Fibre, pulp, insulation etc) or insulation boards any thickness including cover filletscomplete all as specified and directed by Engr-in-Charge

S&F interlocking aluminium power coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00 mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Tee 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm . Aluminium alloy extruded section shall be aluminium anodized ( minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm complete all as specified and S&F Gypsum board of 12 mm thick for ceiling Note :- It is hereby informed to Contractor to visit the Building P-143 before Quoting Rate for Item No 101; ( 2 Coats of Distemper,Cement Base paint & False Ceiling ) As the height of Bldg where work to be executed is upto 20 Mtrs.

M&L for complete removal of existing treatment by washing, rubbing down and stopping of distempered and painting surfaces etc and applying two coats of oil bound distemper all as specified. Note :- It is hereby informed to Contractor to visit the Building P-143 before Quoting Rate for Item No 102; ( 2 Coats of Distemper,Cement Base paint & False Ceiling ) As the height of Bldg where work to be executed is upto 20 Mtrs.

M&L for complete removal of existing treatment by washing, rubbing down and stopping of distempered and painting surfaces etc and applying two coat of cement base paint on walls over a coat of alkali resistant priming paint all as specified. Note :- It is hereby informed to Contractor to visit the Building P-143 before Quoting Rate for Item No 103; ( 2 Coats of Distemper,Cement Base paint & False Ceiling ) As the height of Bldg where work to be executed is upto 20 Mtrs.

S&F in repair curtain rod chromium plated 25 mm dia 1mm thick with pairs of fixing fancy brackets, stops, rollers etc complete all as specified & directed by Engr-in-Charge.

Taking up or down steel water tubing and connection incl cleaning for refixing or removal to stores for following bore :-

S&F GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube :-

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed

(a) 15 mm dia

(b) 20 mm dia

S&F in repairs for Vitreous China squatting pan,"Orissa" pattern,size 580 X440 mm white,withintegral foot rests (excluding flushing cistern and flush pipe) including connection to flushing pipe anti syphonage pipe etc copmlete all as specified.

S&F of vitreous china wash basin,white,flat back,size 450x300mm excluding taps,waste,chain and plug and porcelin stopper but including brackets

S&F of pillar taps of 15 mm bore chromium plated screwed down high pressure with long screwed shanks and fly nuts

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

S&F bib taps, fixed in repair cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixing 15mm bore dia complete all as specified and directed.

S&F for waste fittings,brass,chromium plated of 32 mm dia for wash basins,Urinals

S&F waste coupling of 32 mm bore(half or full threaded)suitable for wash basins,Urinals

S&F Grating doom 100 mm dia of PTMT (Minimum weight 100 gms)

S &F in repairs Vitreous china bowl urinal flat back ,size of 465x355x265 white (minimum),with grating and union for discharge pipe(excluding flushing cistern,flush pipe and waste pipe)

S/F PVC connections 15mm size with PTMT nuts of length 300mm.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for keys, scrubbing down with water, etc.

Supply only integral water proofing compound( ISI marked)

M/L for rendering 15 mm thick on fair faces brick work or concrete surfaces in cement 1:4 and finished even and smooth complete all as specified and directed Note: water proofing compound should be measered separately

M&L for two coats of cement base paint for external faces of walls including preparation to new surfaces

Dismantling wrought iron or mild steel/Cost Iron work of any description not otherwise provided for all as specified and directed by Engr-in-Charge.

S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on newly untreated surfaces of steel over 10cm in width or girth not otherwise described

S&F Aluminium anodised powder coated door shutters aluminium section weighing 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 and fixed with stainless steel wire staples complete.

S&F powder coated aluminium anodized grill of 6/7 mm dia rod square, rectangular, circular or similar type of shape, fixed with channel 38 mm x 12 mm x 1.30 mm (Sec No 8778) all as specified.Make :- DECOREL.

Taking down of existing tarfelt/water proofing treatment on roof top and clean the existing surface with water and providing screed bed 20 mm thick , in CM 1:4 mixed with intregal water proofing compound @ 3% by weight of cement, on fair faces of concrete surfaces and applying cold bituminious oil based primer IS No 3383@250Gms/Sqm and laying APP modified membrane with non woven polyster reinforcement mat (Centre core) not less than 3 mm thick & not less than 3.50 Kg/Sqm, the over the lap otching shall be 100 mm length side and 100 mm width side all as per manufacture's instruction complete all as specified and directed by Engr-in-Charge. Note:- Supply intergral water proofiing compound shall be measured and paid seperatly

M&L 75 mm thick PCC 1:4:8 type D-2 (using 40mm grade stone aggregate) as in Sub floors,Sub bases ,flooring etc

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar work

S&F 30mm thick glazed and skelten shutter open rebated and prerepair to receive glass, gauge etc with sash bars, edge of framing, plain/chamfered or rounded, fitted with cut and metered beads with second class hard wood complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F MS barrel tower bolts stove enameled black with bright bolt – 150mm long fixed complete all as specified and directed.

S&F MS sliding door bolt plate type, stove enameled black with bright bolt not less than 12mm dia with and incl. a minimum of 6 bolts and nuts,four on bolt plate and 2 on staple plate – 300 mm long complete all as specified and directed.

S&F MS pressed handles oval type stove enameled black fixed – 125mm size complete all as specified and directed.

S & F 100mm stainless steel butt hinges medium weight all as specified and directed

M&L for two coats of cement base paint on new plastered surfaces of walls over a coat of alkali resistant priming paint all as specified.

M&L for complete removal of existing treatment by washing, rubbing down and stopping of distempered and painting surfaces etc and applying two coat of cement base paint on walls over a coat of alkali resistant priming paint all as specified.

M&L for applying 3mm thick wall care putty on wall, deep scraped surfaces or undulated surfaces in patches and making good even and smooth rubbing with sand paper etc

M&L for complete removal of existing treatment by washing, rubbing down and stopping of distempered and painting surfaces etc and applying two coats of oil bound distemper all as specified.

M&L for preparation of old previously decorated surfaces by brooming down or steel wire brushes, scrapping down smoke soot, moulds, efflorescent salts etc and applying one coat of white wash on ceiling all as specified.

S&F 75mm bore cast iron sand cast soil waste and vent pipe in any length with or without ears fixed to walls with lead joints (Lead joints measured separately) complete all as specified and directed by Engineer in charge.

S&F 75mm bore CI bends, Diminishing pieces or tapers fixed with lead joints (lead joints measured separately

S&F 300mm Mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete

Dismantling boarding, any description fixed in any position with screws.

S&F Continuous (piano) hinges 30 mm wide flap, mild steel, bright finish or electrogalvanised

S&F 30mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

M&L for 2nd class hard wood scantling clean sawn timber fixed for purlins, posts rafters etc, in any position (unframed work) complete all as specified and directed

M&L for beads exc 3mm but n exc 75mm girth on soft wood

M&L for ball catches with 8mm dia steel ball and brass body and striking plate incl letting in and fixed

M&L for hasp and staple of size 75mm safety type of aluminium anodised incl bolt to hinge plate and fixed with screws

S/F 15 mm angle valve chromium plated with wall flange and fancy type with high pressure screwed down and with CP flange of same complete all as specified and directed

M/L for Point wiring complete with 2.5 sqmm single core multi stranded copper conductor PVC (FRLS) insulated unsheathed cable 1100 Volts grade in & incl PVC casing caping not less than 20mm width with accessories fixed on surface of wall/ ceiling all as per ISI, incl pressed steel terminal boxes (sunk in wall) laminated sheet top cover with 1.50 sqmm single core insulated unsheathed PVC covered copper conductor for common earth & connecting to earth dolly for socket point.

S&F sub main wiring with 2 run of 4 Sq mm single core copper conductor cable drawn through in rigid PVC conduit ISI marked with fitting and 2.5 Sq mm single core copper conductor cable for continues earth wire all as directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps 240V

S&F tube medium grade galvanized with all fittings and fixed complete to wall and ceilings and laid in floor size of 15 mm dia

S&F stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe for unions and fixed of size of 15 mm dia.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm

M&L for earthing complete with copper plate 60×60cm, 3.15mm thick, buried directly in ground (earth pith not less than 2.25 mtr deep below ground level) with top edge of plated not less than 1.5 mtr below normal ground level connected toincl copper strip of size 20x3mm by mean of bolts nuts check nuts & washers of galvanized iron or steel pipe 15mm dia medium grade and connected to main switch board watering pipe shall be 20mm dia GI medium grade incl excavation earth work in any type of soil pit RCC cover complete.

M&L for copper strip 20x3 mm complete.

M& L for preparation of opening for fixing exhaust fans

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver.

S&F water heater 25 Litre complete. Make: Bajaj / Crompton Greaves / Havells / Orient.

Choudhary Traders and Engineers