Interior furnishing and acoustic work of auditorium at hansraj college, Univeristy of Delhi.

Amount

ACOUSTICAL TREATMENT CEILING

Micro-perforated Gypsum board false ceiling Providing & fixing perforated Gypsum false ceiling , as marked in the drawings, consisting of GI perimeter channels of size 0.50mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.8mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.50mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 300mm c/c. Finished in 12.5mm thick micro-perforated gypsum board, 1200mm x 2400mm, with 3mm dia square perforations. The board shall have an overlay of 50mm thick, 1000 GSM polyester wadding, appropriately covered with FGT tissue (in the case of glasswool/ rockwool). The ceiling to be finished with 2 or more coats of mat type plastic emulsion paint after proper jointing & making surface smooth.The Complete Ceiling System Should offer an NRC of 0.85. Approved make of gypsum perforated board: Knauf Danoline/ Absound Overseas/Acoustic India.

Stage suspension Grid: Providing & fixing MS suspension grid system over stage for hanging stage services made of 2 nos 40x40x5mm MS angles welded back to back with 50x12x12mm thk studs as MS spacers sandwiched between the MS angles so as to maintain 12mm gap between MS angles, the welded angles to be placed @ 1200mm c/c in one direction and 40x5mm thick MS Tee @ 600mm c/c in other direction. The MS grid to be suspended from the roof structure by means of MS flat suspender of 50x6mm thick MS flats @ 1200mm c/c in both directions. All MS members to be painted with a coat of red oxide primer & 2 or more coats of black enamel paint.

Woodwool fibril acoustical tiles in stage ceiling: Providing and fixing Fibril wood-wool black acoustical tiles of size 1200x600x25 mm, to be installed existing MS suspension grid. Which will comprise of NRC 0.80. Approved make: Absound Overseas/Herra Design/Acoustic India/Anutone.

ACOUSTICAL TREATMENT WALL PANELING

Wood grained wooden slats paneling: Providing & fixing of Micro Perforated Fluted Panels for Wall paneling, the size of panel will be of custom size as per design. The fluted panels shall be made of twin-layer acoustically perforated material. The first layer is made of 16 mm thick high-density MDF board of 700–750 kg/m3 density with 10mm dia perforation at 28mm c/c and one hole in between all four holes to make diagonal perforation and to increase absorption area up to 45%. The second layer (top surface) shall be of 0.6mm thick mica laminate with micro perforations of 0.5mm to 1mm diameter at a distance of 2-3 mm c/c to be backed with black acoustic fleece as per acoustic design. All joints of micro-perforated acoustic panels should have dowel connections to avoid any sagging or unevenness. All Micro Perforated Acoustic Panels should be fixed on a GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c. The spacing and strength of GI channel supports members shall be according to the projection of the grid and the weight of the acoustic panel, which is approximately 16 kg/sqm fixed to the wall using all self driven screws. The 24 SWG x 12.5mm GI Chicken Wire Mesh to be used to hold 50mm thick 1000GSM thermally bonded polyester wadding. Finally, micro-perforated acoustic panels shall be fixed to a GI channel grid as the final finish. The micro- perforated wall panel shall have an overall 0.85 NRC value and an NRC of 1 for 500 Hz to control low-frequency reflections. The micro-perforated acoustic panel shall have a square edge at all four ends, as per choice. Technical Parameters Absound Micro Perforated Panels Density: 700-750 kg/m3 Fire Retardant, Class (A) The overall NRC value is 0.85. Green(VoC) Low. Core: MDF and Perforated Mica Climate (OC RH): 40, 90 Hygiene (VoC, Clean Room): Low Class 3. Approved make: Topakustik/Absound Overseas/Acoustic India/Herradesign.

Fabric paneling on walls : Providing and fixing Acoustical wall paneling with Melamine foam panels, provided with upholstery on the front side with an acoustical and fire-resistant fabric with an option of colours as per the choice of the person-in-charge. The melamine foam panels to be pasted over 9mm thick perfored ply and GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1000GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. The melamine foam panels to be finished with 340GSM fabric stretched with specially made UPVC grippers. All complete including making arrangement for fixing of grippers as per the guidlines of manufacturer. Approved Make : Acoustic India/ Absound Overseas/AMF/Topakustik. Fabric cost to be taken as Rs. 465/sqm.

Providing and fixing 4mm thick wooden Decorative Veneers over 12mm thick MR grade ply with adhesives. The ply to be fixed over GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1000GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. The Wooden Veneers to be Finished with a coat of wooden sealer, 2 Coats of spirit polish and finally with a balancing coat of melemine polish.Approved Brand Makes.

Providing and fixing LED wall support structure on stage consisting of MS frame of 50x50x2.2mm thick MS tubes welded @ 600mm c/c in both directions, the frame to be painted with a coat of steel primer and supported from floor and ceiling with fasteners. The MS framing to be provided with 12mm thick ply on both sides. Back side to be finished with black enamel paint and front side in combination of sound slats and polyester panels. (the item of sound slats & polyester panels to be paid in relevent items.) All complete as per the drawings and design.

Providing and fixing 100 mm ht. approved aluminium extruded profile skirting (readymade section) on RCC/ Brickwall/Ply surface made out of 18 gauge aluminium, powder coated with shade as approved by architect with a thickness of 50 microns. Skirting to include all nesessary fixing details all complete as per detail drawing. Make: Bottomline, Hindalco, Absound.

STAGE FURNISHING

SUPPLY INSTALLATION TESTING AND COMMISSIONING of FRONT CURTAIN made out of FR Treated approved colour velvet cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. Make of fabric: Banswara, Reliance, Nexgen. Make of Track system: Canara / New Age / Leksa

SUPPLY INSTALLATION TESTING AND COMMISSIONING of MIDDLE & REAR CURTAIN made out of FR Treated approved colour glazed cotton cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. size 21000x9000. Make of fabric: Banswara, Reliance, Nexgen Make of Track system: Canara / New Age / Leksa

Providing and fixing WINGS at Stage with fire retardant glazed cotton black fabric ( weight not less than 320gms/sqm of Make: Response/ RSWM/Banswar Syntax) fixed complete on 50x 25(1.6 mm thick) MS tube framework @ 1200 (V) x600 (H) c/c backed with 6mm ply & 6mm U foam below the fabric. The rear side of the wing to have 12mm Gypsum board The gypsum board to be given 2 coats of black enamel paint after jointing fisnishing as per the manufacturers recomendations. The side edge to be given a teak wood molding of size 90x15mm duly polished in walnut shade. The wing to be mounted with central pivot mechanism for 180 degree rotational movement at top & bottom.Size 1.2 mtr (w) x 9.0mtr (h) approx. The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

Providing & fixing of the Border frills out of Fire retardant glazed cotton black colour ( weight not less than 290 gms/sqm Make: Comrade/RSWM/Banswara Syntax)) fabric in 1:2 gathers & acessories like cotton dori eyelets of brass complete with 25mm dia medium grade GI pipe painted black suitably hung from the ceiling complete . The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

Providing and fixing stage proscenium consisting of MS tubular frame made with 50x50x2.2mm thick MS tubes, painted in black colour, to be fixed to floor and ceiling with fasteners. Front side to be finished with 12mm thick MR grade ply and 1mm thick laminate of approved colour. Rear side to be finished with 10mm thick polyester panels.

Providing and fixing of 90x22 mm Maple wood klin seasoned planks with tongue & groove joints. Teak wood planks to be of minimum length 750mm. The Maple wood planks to be fixed over a layer of 18 mm thick MR grade ply of approved make fixed to Sal wood frame work of 50 x50 mm and 50x50 mm at 600 mm centre to centre (HxV). The Sal wood shall be kiln seasoned and chemically treated. The framework to be jointed with mathani cut method. The framework to be supported on 100 x 100 x 8mm neoprene pads . The framework to be filled with 50 mm thick thermal bonded polyester wadding mikron fiber of 1000 gm/sqm mikron fiber. The stage floor to be PU polished with use of orbital sanders to make floor even before polishing.

Providing and fixing first class teak wood lipping/moulded beading or taj beading of size 70x50mm fixed with wooden adhesive of approved quality and screws/nail on external edges of stage .The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

SITC of Motorised integrated fly bar/ set bar of 15 Mtr. Length Motorized Set bar, The Which shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, motor. It shall have a Worm Reduction gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which Contains one shaft. This mechanism shall have drum Plate of 300mm x 5mm thickness with 6 Groves where the GI wire rope of 5mm can be winded up when the hoist moves up and down. 415VAC Motor with Brake for Motor System to lift a load of 100KG as a safe working load which should be synchronized with Control Panel. WiFi operated wireless smart working functionality Dual Barrel duly powder Coated Made Using 40NB Dual construction Matt black texture finish paint to keep them rust free. Powder coated 60 microns black matt finish with proper chemical treatment and methodology. Wifi Based up down lightbar movement Specially desihned compact gear box 1 phase AC motor with DC Brake 1.5HP. Provided with Necessary pulley, guide pulleys, GI wire rope with winding drum. Compact gear box along with suitable capacity of motor unit. Upper and lower limit controller, safe working load of 100KG . Cable management system. Make:- Leksa / ETC / Absound.

SOUND REDUCING DOORS

Supply & fixing of Double leaf acoustic door of 83mm thickness, acoustic door shutters with all necessary intumescent and fire seals, having infill of 47mm thick resin bonded glasswool of 24kg/cum density coated Sandwitched between 9 mm thick calcium silicate board (100% without asbestos, Brucite and Meerschaum having a density not more than 1150kg/cum and thermal conductivity 0.14 W/M*K) and facing with 12mm thick MR grade ply & 1mm thick laminate (green/merino/century) with acosutic seals all around. The work shall be executed as per approved drawings, specifications & instructions of engineer in charge. (Recomended Make : Global/ Navair/ Absound Overseas.

Providing & fixing of Seacond class teak wood of section 300x90mm in frames of acoustical doors & projector room window including fixing with 180mm long MS fasteners, 4 nos each side. The wood work to be finished in spirit polishing of approved shade.

Providing and fixing of panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. Make: Becker/Dorma/Assa Abloy

Supply & fixing of stainless steel ball bearing hinges of size 100x100x2.5 mm thick complete .The work shall be executed as per approved drawings, specifications & instructions of engineer in charge. Make: Becker/Dorma/Assa Abloy

Providing and fixing external trim with locking arrangement & handle for panic bars double/single leaf with all necessary parts. Make: Becker/Dorma/Assa Abloy

Providing and fixing of aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 100kg to 120 kg , with double speed adjustment with necessary accessories and screws etc. all complete. Make: Becker/Dorma/Assa Abloy

Providing and fixing set of seals in doors and door frames (doors and door frames to be paid for separately) consisting of fire and intumescent seals and complete set of acoustic seals (RP 24, 16 & 38) to achieve 38 dB noise reduction, complete as per drawings and direction of Engineer-in-charge. Make: Becker/Raven/Athemer

Providing and fixing 70x20mm wooden moulding/beading to the wooden chowkhats, to be finished in polishing

AUDITORIUM SEATING & CARPET FLOORING

Providing and fixing of 550mm c/c Fire Retardant velvet fabric having Scotch guard water repellent treatment (FR Fabric conforming to BS EN 1021&1) upholstered chair. The chair to have MS tubular framework welded together with continous arc welding. The chair shall have powder coating of 65microns on all of the MS tubular framework . The seat shall have Polyurethane foam of density 50+3 KG/Cum & Back to have density of 50+3 Kg/CuM. The height of the back to be 950-1000mm from the ground to top of back & for Seat to be 400-450mm from the ground . The rear of back shell & bottom of seat shell to be Polypropylene plastic in black colour Polypropylene plastic cover. Option of wooden/PPCP armrest. The wooden armrest to be of 80mm & 400mm length with melamie polished in black colour . The armrest between two chairs in a row to be shared & at the both ends to be individual. Including cost of expnasion fastners as required of reputed make. The bench shall be fabricated as per drawings ,specifications & instructions of engineer in charge. Approved Make:Wipro / Featherlite / Absound seating.

Supplying 3 seater sofa sets as per the seating layout. The sofa to be fabricated in teak wood framing, high density PU foam, polyester wool for making sofa back and top. Sofa legs to be made of Stainless steel. The sofa to be upholstered with scotch guard water repellent fabric of required colour. Cost of fabric Rs. 700/sqm. Make:Wipro / Featherlite / Absound seating.

Supplying 2 seater sofa sets as per the seating layout. The sofa to be fabricated in teak wood framing, high density PU foam, polyester wool for making sofa back and top. Sofa legs to be made of Stainless steel. The sofa to be upholstered with scotch guard water repellent fabric of required colour. Cost of fabric Rs. 700/sqm. Make:Wipro / Featherlite / Absound seating.

Providing and fixing Wooden tables of size 1200x600mm made of teak wood frame and teal wood top. The wooden top and legs to be finished with orbital sanding, filler coats and melamine polishing. All complete as per the design and drawings.

Providing and fixing machine tuffed cut pile high low scroll nylon carpet effective pile height 9mm, total pile weight not less than 1500 gm/sqm. secondary backing action back 200 gms/sqm. In rolls of 3.66 mtr. width as per size, shade, design and direction of Engineer-in-charge and as per manufacturer's specifications. The sample may be approved by the Engineer-in-charge before start of the work. The surface area will be measured for payment. The carpet to be bakced with 8mm thick PU underlay. The fexisting flooring to be levelled by cementious levelling compound of thickness 4-5mm before laying of carpet. Approved make: Birla transasia, Heritage, CCIL.

Providing and fixing loop pile type carpet of weight 220z., having 4mm thickness. The carpet should be of roll up type. Make:-CCIL, Unitex, Jupitor.

STAGE LIGHTING SYSTEM

SITC of 100W Zoomable High Quality LED Parcan Light complete with COB Lamp source 3200K CCT Colour temperature, CRI & TLCI Values above 90, DmX 512 dimming with 2 channel conmtrol, Beam Angle of 11 to 35 Degree, Black powder coated housing, suitable for Stage lighting to illuminate the key areas. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 300W LED Profile Spot 19 Degree Light complete with 3200K CCT Colour Temperature, CRI & TLCI above 90, DmX 512 dimming with 1 or 3 Channel modes, Black finish housing, IP20 protection having Lux @ 2 Mtrs above 27,000 suitable to illuminate the key presentor or talent on stage. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 200W LED Profile Light 26 degree 3200K color temperature with High quality parameters of CRI & TLCI 95+ Luminaire provided with gel holder, Gobo holding. 0% to 100% Dimming, 3 Channel DmX Control, Manual focus with 4 beam shaping cutters with Master Slave & Manual adjustment.IP20 Rating of Protection. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 200W LED Fresnel Light 3200K colour temperature. High quality uniquely designed Fresnel Lens. Flood and Spot Manual beam Focus, Beam Angle 10 ~ 40 Degree, CRI-98, TLCI-97 and R9 value -95. Sensor Based Cooling system. Manual and DMX control Option mode through 5pin xlr. Black powder coated fabricated housing with normal yoke but without accessories. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 400W LED Blinder Light 30 Degree complete with 3200K/5600K CCT 4x100W Chip On Board LED Lamp source, DmX 512 dimming with 4 /8 Channel modes, Black finish housing, IP20 protection having Strobe option and smooth dimming, illuminate Stage with uniform light intensity levels. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 54 x 3W LED Par Light 3 in 1 Beam Angle 25° complete with RGBW 3W Lamp source x 54 Pcs, DmX 512 dimming with 8 Channel , Powder coated Black finish housing, IP20 protection having Sound Control & Master Slave Auto Run Mode. Illuminate the Indoor stage with unlimited colour effects. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 54x3W LED 3200K Par Light Beam Angle 25° complete with 3200K 3W Lamp source x 54 Pcs, Having CRI TLCI Values above 95, Flicker Free for high FPS, Smooth fade in and Fade out, High precision steady color, No heat, DmX 512 dimming with 2 Channel, 0 ~ 100%, Powder coated Black finish housing, IP20 protection. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Moving Head Beam effect light 12R Base high bright long throw beam, 280W 12R Lamp, 16 Channel DmX Control, Motorized Beam adjustment 5°, 8 Facet Prisms and Prism rotation effect, Master Slave, Test Modes, Sound Active and Auto Run Mode, Pan Angle 540°, Tilt Angle 270°, DmX control through 3 / 5 Pin XLR’s, IP20 rated product. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of High quality 200W LED Profile Spot Light used as a Spot Light and high-contrast gobo projection Light. Other Technical specifications as below: • Lamp Power : 200W COB LED • Power Supply : AC 110-230V, 50Hz. • CRI : >90 • Colour Temperature : 3200K • Focus : Manual Focus • Beam Angle : 19° • Control : DMX, Autorun and Master/Slave • Shutter arrangements : Beam shapping shutter or plastic gobo projection assembly. • Lux Level - 20,375 lux @ 2 Mtr with beam angle 19°,3200K. • Dimming : 0 - 100% dimming • Protection Rating : IP20 • Body Color : Black • Weight : 7.50Kg • Dimentions : W 300 x L 700 x H 310 mm. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Light fixture mouting clamp customized for suspending on fixed bars on stage made up of Aluminium or MS material complete with black powder coating matt black finish. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Light Fixture dual safety chain made up of GI wire rope bundled and twisted together having load bearing capacity above 200 Kgs, sleve on the rope. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Suspender cum clamps designed as per site conidition made out of MS material of size 50x 50x 6mm with black powder coated finish and threaded rod of minimum 12mm suitable to hold Basic grid of Drepary System and Lightbars. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 10 Mtr On Stage Fixed Lighting Bar Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, dual construction connected with MS Flat duly powder coated with matt black texture finish. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 11 Mtr FOH Fixed Lighting Bar Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, dual construction connected with MS Flat duly powder coated with matt black texture finish. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of 4 Mtr on stage side Fixed Lighting Bar Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, dual construction connected with MS Flat duly powder coated with matt black texture finish. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Power Distribution Electrical panel having a incomer of 63A floor mount / rack mount / wall mount with nuetral separation made using incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization, individual MCB control for 28 outgoing circuits, separate incomer control for Motor control panel supply, RYB Phase indicators internally wired using IS certified wires and cables, provided with ivery connectors for the internal terminations and external outgoing connecting points custom built as per specification and project requirement. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of High quality power junction box 4 way made up of MS Sheet metal fabricated housing black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Internal Earthing System with copper bare conductors all along the cable trays, metal parts and Installation Hardwares. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 150mm with perforation for heat dessipation provided with lid. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 75mm with perforation for heat dessipation provided with lid. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal deframing. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Opto isolated RDM enabled DmX splitter unit complete with Power In and safety fuse, 8 Output channels 5 Pin XLR in and out supporting DMX operation as per DmX 512 protocol. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of DmX Touch Screen based controller having 7” Multi touch screen option 2 DmX Outlets 5 Pin XLR’s, 512 Channels each, Optically isolated outputs, 4 Smooth Encoders for control operation of attributes, Backlit keys, 12 Fader Stacks, 600+ Playbacks, 350+ Group saving, 350+ Presets, User defined shape effects, Macro saving options, External Midi timecode options, Internal clock, Shortcut user interfaces, Master fader, Blackout Key under Master fader, Numerical keypad for the light command entry inbuilt embedded within controller, USB interface, Scene saving options, Show saves and load save features, custom built user interface library for fixture files. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of FRLS Copper unarmoured Flexible cable having 3 Core each of 1.5 Sq mm size. Approved makes: Polycab / Havells.

SITC of 5 Core DmX Cable with Sheathed housing on the cable, well designed insulation, low noise suitable to transmet DmX signal. Approved makes: Polycab / D Link.

SITC of FRLS Copper unarmoured Flexible cable having 4 Core 4 Sq mm size. Approved makes: Polycab / Havells.

SITC of Motor Control Panel cum remote control 1 Way providing power input for curtain motors internally neatly wired with contactors having individual motor control with required Push button, Emergency trip, RYB indicators, Supply Indictor and necessary meters. Motor control panel duly powder coated with ash grey paint texture finish with all required safety features. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of Cable Connecting Circuit Boxes for the termination of cables from Electrical panel to the grid level point made out of MS Sheet metal fabricated housing duly powder coated with matt black texture finish paint, fitted with required channels and ivery connectors, necessary glands etc. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of FRLS Copper unarmoured Flexible cable having 7 Core each of 1.5 Sq mm size. Approved makes: Polycab / Havells.

SITC of High quality power junction box 2 way made up of MS Sheet metal fabricated housing black powder coated, 2 10amps 3 pin IEC socket, ON/OFF switch and necessary glands. Approved makes: Leksa Lighting / Canara/ Martin.

SITC of High quality DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR, Female Socket & 1 No. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. Approved makes: Leksa Lighting / Canara/ Martin.

FRLS Copper unarmoured Flexible cable having 7 Core each of 1.5 Sq mm size. Approved makes: Polycab / Havells.

Programming the Stage Lighting system, operating the system for 1 year and training to technical college staff for operating the system.

SOUND REINFORCEMENT

Sound Reinforcement System

Supply, Installation, Testing and Commissioning of Main FOH Left, Right and Center Compact Two Way Dual 8" or better (minimum two driver LF configuration), with Minimum 2 x 1" HF Driver Biamplified Operation Rated power LF : 450 Watts RMS or better, HF : 60 Watt RMS or better. Impedance : 8/16 Ohm. Frequency Response 70 Hz – 20 kHz (± 3db). Sensitivity LF: 94 dB or better, HF: 101dB or better. Maximum SPL 127 dB peak. Dispersion : 110°x 7.5° to 10° Integral variable curvature Birch Plywood Enclosure Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of FOH Left and right Array Subwoofer Compact Dual 15" or better (Dual Driver Configuration) better Rated Power : 1000 Watts RMS or better Impedance : 4 Ohms Frequency Response 40 Hz - 200 Hz Sensitivity 98 dB Max SPL 137dB Peak or better All complete to be flown as array as part or line array system or seperate array hung set Birch Plywood Enclosure Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of LCR Array and Subwoofer Mounting Kit Single point suspension To provides desired tilt angle and toe-in for optimum positioning Shall be from same OEM of FOH Speakers and Subwoofers Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Stage Monitor, 2 way co-axial active speaker 12" LF ,1" HF Driver Coaxial Design Rated Power 1000 Watt or better Class-D Amplifier Frequency Response : 70 Hz – 18 kHz or better Maximum SPL 125 dB peak or better 60-80 degree Horizontal x 40-50 degree Vertical Dispersion Birch Plywood construction In-Scenario of Passive Stage Monitor; the Amplifier shall be considered from the given Tender Makes with minimum Headroom of 50% over RMS Power Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Front Fill Speaker, 2-way full range Passive loudspeaker system Speaker Type: 2-way full range Passive loudspeaker Component : 8"LF driver, 1"HF driver Power Handling: 150 W continuous or better Impedance : 4 ohms or better Frequency Range: 58 Hz - 20 Hz Dispersion : 70°-90° (H) x 60°-70° (V) Maximum SPL : 118 dB peak or better System Sensitivity : 91dB or higher Birch plywood enclosure Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Customized Bracket for the above loudspeakers. Approved Makes: Custom/ Eqv.

Supply, Installation, Testing and Commissioning of Side/Rear Surround Speaker 2-way full range Passive loudspeaker system Speaker Type: 2-way full range Passive loudspeaker Component : 8"LF driver, 1"HF driver Power Handling: 150 W continuous or better Impedance : 4 ohms or better Frequency Range: 58 Hz - 20 Hz Dispersion : 70°-90° (H) x 60°-70° (V) Maximum SPL : 118 dB peak or better System Sensitivity : 91dB or higher Birch plywood enclosure Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Customized Bracket for the above loudspeakers. Approved Makes: Custom/ Eqv.

Supply, Installation, Testing and Commissioning of Rear Surround Speaker 2-way full range Passive loudspeaker system Component : 10" LF driver, 1.5" HF driver or better Power Handling: 350W-400 W continuous or better Impedance : 8 ohms or better Frequency Range: 50 Hz - 20 KHz Dispersion : 80°-90° (H) x 40°-50° (V) Maximum SPL : 128 dB peak or better System Sensitivity : 96dB or higher Plywood enclosure Rigging Point for flying hardware Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Customized Bracket for the above loudspeakers. Approved Makes: Custom/ Eqv.

Supply, Installation, Testing and Commissioning of Under Balcony Fill Speaker 2-way full range Passive loudspeaker system Component : 10" LF driver, 1.5" HF driver or better Power Handling: 350W-400 W continuous or better Impedance : 8 ohms or better Frequency Range: 50 Hz - 20 KHz Dispersion : 80°-90° (H) x 40°-50° (V) Maximum SPL : 128 dB peak or better System Sensitivity : 96dB or higher Plywood enclosure Rigging point for flying hardware Approved Makes: Turbosound / Martin Audio / JBL/BOSE / D&B Audiotechnik.

Supply, Installation, Testing and Commissioning of Customized Bracket for the above loudspeakers. Approved Makes: Custom/ Eqv.

Supply, Installation, testing and commissioning of Green Room Speaker Compact Surface Mount Loudspeaker: Green Room 4" LF or better RMS Power 25 W or better Transformer Taps at 70V/100V - 25W/12.5W/6.3W Impedence 4 to 8 Ohms Frequency Response (-10dB): 70 Hz - 20 kHz Maximum SPL 102 dB Peak or better System Sensitivity 82 dB 90°-100° conical dispersion Complete with mounting accessories Approved Makes: Tannoy / AtlasIED / Martin Audio / Bose/ JBL.

Supply, Installation, testing and commissioning of 4-channel 8000Watt Network amplifier with DSP Class TD or D Nos. of Channel : 4 Power Handling : 4 × 2000 W @ 2/4 Ohms, 4 × 1500 W @ 8 ohms Max power per channel in case of bridge mode / Power management should be 4600 watts @ 4 ohms and 2300 watts @ 8 ohms, and 5500 Watts @ 2.67 Ohms Amplifier Gain configurable gain from 22dB to 44 dB THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 194V with Max output current up to 67 Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs or better DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters or better Peak and RMS limiters Support Multiple Makes Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant Dante network audio inputs Control Ports 4 Analog inputs Two AES3 digital inputs Approved Makes: Labgruppen / D&B Audio Technik / crown/ Bose/AKG.

Supply, Installation, testing and commissioning of 4-channel 4000Watt Network amplifier with DSP Class D Nos. of Channel : 4 THD 20Hz-20kHz at 1 W <0.1% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 1000 W @ 2/4 Ohms, 4 × 1000 W @ 8 ohms Max power per channel in case of bridge mode / Power management should be 1750 watts @ 4 ohms and 1350 watts @ 8 ohms, and 1150 Watts @ 2.67 Ohms Amplifier Gain configurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 150V with Max output current up to 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs or better DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters or better Peak and RMS limiters Support Multiple Makes Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant Dante network audio inputs 4 Analog Inputs Control port Two AES3 digital inputs Approved Makes:Labgruppen / D&B Audio Technik / crown/ Bose/AKG.

Supply, Installation, testing and commissioning of Four Channel 2000 Watts Network amplifier with DSP Class TD or D Nos. of Channel : 4 Power Output all channel driven: 4 x 500 W @ 4 Ohms, 4 x 500 W @ 8 Ohms per channel Max power per channel in case of bridge mode / Power managmenet should be 1500 watts @ 4 ohms and 1000 watts @ 8 ohms THD 20Hz-20kHz at 1 W <0.05% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 140V with Max output current upto 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs or better DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters or betterPeak nd RMS limiters Support Multiple Makes Speaker presets Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant Dante network audio inputs Control port 4 Analog Inputs Two AES3 digital inputs Approved Makes: Labgruppen / D&B Audio Technik / Powersoft / L-Acoustics / Coda Audio

Supply, Installation, testing and commissioning of 4-channel 1000Watt Network amplifier with DSP Class TD or D Nos. of Channel : 4 THD 20Hz-20kHz at 1 W <0.1% Dynamic Range >112 dB Channel separation at 1 kHz >70 dB Power Handling : 4 × 250 W @ 2/4 Ohms, 4 × 250 W @ 8 ohms Max power per channel in case of bridge mode / Power management should be 1000 watts @ 4 ohms and 1000 watts @ 8 ohms, and 1000 Watts @ 2.67 Ohms Amplifier Gain configurable gain from 22dB to 44 dB Frequency Response (1W into 8 ohm,20 Hz-20kHz) +/- 0.05 dB Peak output Voltage 142V with Max output current up to 30Amps 96KHz Sample Rate DSP Features: classic/linear-phase/FIR speaker processing platform with four throughputs or better DSP Features: Group control with Raised Cosine MESA EQ asymmetric filters or better Peak and RMS limiters Support Multiple Makes Speaker presets Comprehensive clocking management system with low latency sample rate conversion Protection Features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection Eight dual-redundant Dante network audio inputs 4 Analog Inputs Control port Two AES3 digital inputs Approved Makes: C245

Supply, Installation, testing and commissioning of Dual Channel 120Watts Power amplifier Class D Nos. of Channel : 2 Power output : 2 × 60 W @ 4 ohms, 8 ohms, 70 /100 V Distortion, 1/8 rated power <0.05% THD 20Hz-20kHz at 1 W <0.5% or better Signal To Noise Ratio: >97 dBA Channel separation (Crosstalk) >85 dBA High-pass filter 80 Hz HPF Frequency Response : 20 Hz to 20 kHz Energy Star Rated Approved Makes: Labgruppen / D&B Audio Technik / crown/ Bose/AKG.

Supply, Installation, Testing and Commissioning of Digital Signal Processor AEC Mic / Line Input: min 10 No's Line Output: min 6 No's USB Audio Interface 24Bit, 48Khz GPIO Contcats: 6 No's Built in Digital Audio DANTE Network with 64 x 64 Channel Frequency Response: 20Hz to 20KHz Ethernet Port: Yes RS232 connector for interfacing with 3rd party control systems Crosstalk (inter-channel @ 1 kHZ): < -75 dB Common mode rejection: Typically, -60 dB at 1 kHz Latency: <1.8ms Maximum output level: -31 dBu to +24 dBu THD+N : <0.005%, Dynamic range: > 105 dB Approved Makes: Labgruppen / D&B Audio Technik / crown/ Bose/AKG.

Supply, Installation, testing and commissioning of 40 channel digital console for live and programm audio Min. 32 microphone preamplifiers 25 time-aligned and phase coherent mix buses AES50 networking , 40 bit digital signal processing 8 stereo signal processing effects engines 8 DCA and 6 mute group 32X32 channels USB 2.0 audio interface Includes built-in/External 32X32 Dante Inteface Card MIDI Inputts/Outputs, DIgital Link power Min 25-100MM motarised faders 7" full colour TFT display screen Built-in RTA for all channel, remote controllable, auto-ranging universal switch-mode power supply Approved Makes: Behringer / Yamaha / Allen & Heath/ Labgruppen / D&B Audio Technik / crown/ Bose/AKG.

Supply, Installation, testing and commissioning of Stage BOX 32 Input, 16 Output Stage Box with 32 Microphone Preamplifiers Remote operation via shielded CAT5e cable up to 330 ft / 100 m length Switchable 48 V phantom power 2 x AES50 or OEM specific network ports or redundant connections Digital audio and control connectivity MIDI In/Out for bidirectional communication Auto-ranging universal switch-mode power supply A/D converter 24-bit, 48 kHz and D/A converter 24-bit THD + noise, unity gain, 0 dBu out< 0.01%, unweighted Shall be from same OEM of digital mixing console Approved Makes: Behringer / Yamaha / Allen & Heath

Supply, Installation, Testing and Commissioning of UHF Wireless handheld microphone system Cardioid dynamic Receiving System : True Diversity Modulation mode : FM Frequency Response : 100 Hz to 15 kHz RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination) Total Harmonic Distortion: <1.0% (at 1 kHz, ±20 kHz deviation) Dynamic Range > 110dB switch function : Mute/unmute Operating range: 100 m (300'), RF Power Output High: 30 mW, Low: 10 mW (switchable) No. of Channel : 10 channels per band Accessories Included: detachable Antennas, Rack mount kit Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of UHF Wireless Lapel microphone system Cardioid Condenser Receiving System :True Diversity Modulation mode :FM Frequency Response : 100 Hz to 15 kHz RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination) Total Harmonic Distortion: <1.0% (at 1 kHz, ±20 kHz deviation) Dynamic Range > 110dB switch function : Mute/unmute Operating range: 100 m (300') RF Power Output High:30 mW, Low: 10 mW (switchable) No. of Channel :10 channels per band Accessories Included: detachable Antennas, Rack mount kit Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of UHF Wireless Headworn Microphone system with beltpack transmitter Omnidirectional Condenser Receiving System : True Diversity Modulation mode : FM Frequency Response : 100 Hz to 15000 Hz RF Sensitivity: 20 dBuV at 60 dB S/N ratio (50 ohms termination) Total Harmonic Distortion: 1.0 % or less (at 1 kHz, ±17.5 kHz deviation) Dynamic Range 110 dB or higher (A-weighted), typical switch function : Mute/unmute Automatic frequency scanning to find open channel Operating range: 100 m RF Power Output High: 30 mW, Low: 10 mW (switchable) No. of Channel : 10 channels per band Microphone Terminated with 55" cable and locking 4-pin connector Accessories Included: detachable Antennas, Rack mount kit Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of Antenna distribution system UHF (wide-band 440-900 MHz) active unity-gain diversity system Enables one pair of antennas to feed Four wireless systems Each distribution system must have identical independent 1-in by 4-out sections each providing a single antenna input, four isolated protected RF outputs and 1 cascade output Interconnection of the units in a cascade fashion for an expanded system must be possible All RF connections shall be rear panel mounted using standard BNC-type connectors 12V DC power to each antenna input to operate powered antennas or in-line RF devices up to 100 mA minimum. Accessories Included: Rack mount kit & BNC cable x 8 Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of Pair of UHF wide-band directional / Omni antennas Operating Bandwidth : 470-990 MHz Antenna Type : LPDA (log periodic dipole array) / omni antennas Impedance : 50 Ohms Typical Gain : 6 dB Typical Enhanced signal pickup for UHF wireless systems Must have High-quality, low-loss BNC connectors to minimize RF cable strain Mounts should allow for vertical tilt adjustment through a 90°range Horizontal adjustment should be possible by rotating the antenna in the mounting fitting Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of Passive Antenna Combiner Kit for UHF wireless receivers and antennas Includes two Passive Antenna Combiners Broadband Operation, frequency range from 470 to 990 MHz Impedance: 50 ohms Industry-standard BNC-type connectors. With Unity gain to compensate for RF signal loss associated with combining signals Complete with two 18” BNC-to-BNC RG 58 coaxial antenna cables Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply and Laying of Antenna Cable RF antenna cable with BNC to BNC connectors, RG8-type cable -100mtr Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and commissioning of Gooseneck Microphone with Quick-Mount Anti Shock Microphone Desk Stand Cardioid Condenser Gooseneck Length: 18"-20" Frequency Response : 30 - 20,000 Hz Impedance : 250 ohms Maximum Input Sound Level: 139 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range: 114 dB, 1 kHz at Max SPL Signal-to-Noise Ratio: 70 dB, 1 kHz at 1 Pa LOW FREQUENCY ROLL-OFF: 80 Hz, 18 dB/octave RFI Shielding Technology Desk Stand Should Effectively isolates microphone from noise, shock and vibration transmitted through the mounting surface. Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, testing and commissioning of Hypercardioid dynamic Neodymium handheld Vocal microphone Frequency Response of 60 - 14,000 Hz Open Circuit Sensitivity -54 dB (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better On/off switch Integral 3-pin gold-plated XLRM-type connector Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, testing and commissioning of Hypercardioid dynamic Neodymium handheld Instrument microphone Frequency Response of 60 - 14,000 Hz Open Circuit Sensitivity -54 dB (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better on/off switch Integral 3-pin gold-plated XLRM-type connector Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen Approved Makes: : Audio Technica/ Shure / Sennheiser

Supply, Installation, Testing and Commissioning of Active DI Boxes for electronic instruments Powered by +48 V phantom power with a 9 V battery backup Signal levels ranging from +10 to +50 dBu Frequency response from 10 Hz to 90 kHz (±3 dB) Earth Lift Switch Approved Makes: Klarkteknik / Radial / Cardinal

Supply, Installation, Testing and Commissioning of 9.2 Surround Sound Processor with XLR pre-Amp output, Dolby TrueHD, Dolby Atmos, Dolby Atmos Height Virtualization, Dolby Atmos Music, Auro 3D, 360 Reality Audio / MPEG H, Wifi, Bluetooth, Ethernet RJ-45, Approved Makes: Denon/Marrantz/Eqv.

Supply and fixing of UL listed Connectors & Patch Cables/Connectors for interconnection of all equipments complete with standard accessories as per the tender specifications. Approved Makes: Neutrik / Amphenol / Switchcraft / Proel

Supply and fixing of Customized Floor Box with 4 x XLR In for Microphones and 1x 15 Amp. Universal power Socket with standard accessories as required as per the tender specifications. Approved Makes: Custom

Supply and fixing of Customized Floor Box with 2x XLR Out for Stage Monitor and 2x 15 Amp. Universal power Socket with standard accessories as required as per the tender specifications. Approved Makes: Custom

SITC of Adjustable tripod stand with Boom Heavy Duty Clutch Assembly Finished in Non-Reflective Ebony, Three, low profile metal legs with cup terminations for optimum stability and balance tripod adjustable from 36"" to 64"" Two section metal tubing with 3 piece clutch for easy vertical height adjustment The end is threaded 5⁄8""-27 and includes a lock-nut ring for versatile positioning of accessories or extension boom Base spread of 25"" (653mm) inches and weighs 5lbs or less Friction notches on the boom swivel to prevent sagging when using heavy microphones BOOM LENGTH of 22"" - 37"" and STAND HEIGHT of 19"" - 30"" Cast 0.5 lb counterweight allows for proper boom positioning while maintaining boom arm balance" Approved Makes: AtlasIED / K&M / Gravity

SITC of ALL-PURPOSE heavy duty Floor Microphone Stand , 12" dia. die cast circular base or better size,Edge concentrated weight distribution, Equipped with rubber pads to absorb shock and protect floor surfaces.The 5/8" and 7/8" dia. tubing is fully adjustable with a vertical extension ranging from 37" to 66" with Wearproof, 3-Piece Clutch Offers Secure, Fast, & Noise-Free Height Adjustment, Tubing is manufactured of cold rolled steel , Industry standard 5/8" - 27 thread suitable for microphone clamps and accessories, Top and bottom lock-nut rings, finished in ebony epoxy to eliminate reflections caused by high-intensity lighting Approved Makes: Garvity / K & M / AtlasIED

SITC of ALL-PURPOSE DESK STAND, Base Size : 10", Stand Height adjustable 9" to 12" with Wearproof, 3-Piece Clutch Offers Secure, Fast, and Noise-Free Height Adjustment, Versatile Stands Fulfill Functional and Aesthetic Miking Requirements for Microphone Placement, Ideal for professional miking of drum kits, percussion and string instruments, and guitar/bass guitar amplifiers. Includes a threaded tip assembly for compatibility with a variety of booms, clamps, goosenecks, and accessories. Approved Makes: Garvity / K & M / AtlasIED

Supply and Laying of 2 core 2.5 sqmm loudspeaker cable PVC insulated Cu conduction loudspeaker cable with Conductor 80 x 0.20 mm, Capacitance 97 pF/m, Outer dia 9.0 mm, working temperature -20 °C / +70 °Complete with standard accessories as per the tender specifications. Approved Makes: Klotz / Belden / Proel / Sommer

Supply and Laying of 2 core 4.0 sqmm loudspeaker cable PVC insulated Cu conduction loudspeaker cable with Conductor 128 x 0.20 mm, Capacitance 97 pF/m, Outer dia 10.4 mm, working temperature -20 °C / +70 °Complete with standard accessories as per the tender specifications. Approved Makes: Klotz / Belden / Proel / Sommer

Supply and Laying of 2 core 6.0 sqmm loudspeaker cable PVC insulated Cu conduction loudspeaker cable with Conductor 189 x 0.20 mm, Capacitance 97 pF/m, Outer dia 13.6 mm, working temperature -20 °C / +70 °Complete with standard accessories as per the tender specifications. Approved Makes: Klotz / Belden / Proel / Sommer

Supply and Laying of 2 core shielded microphone cable PVC Insulated Microphone cable with Ultra low Capacitance 60(Pf/m) , Outer Jacket PVC Matt , Working Temperature :20 °C / +70 °C , Diameter 6.5mm , extremely flexible as per the tender specifications. Approved Makes: Klotz / Belden / Proel / Sommer

Supply, Installation, Testing and Commissioning of 42U Equipment Rack for housing all rack mountable equipment with front glass door, heat dissipation fans, internal lights, movement wheels, power distribution units etc. complete with standard accessories. Approved Makes: AtlasIED / Rittal / Valrack / President

Supply, Installation, Testing and Commissioning of 12U Equipment Rack on stage for housing all rack mountable equipment with front glass door, heat dissipation fans, internal lights, movement wheels, power distribution units etc. complete with standard accessories. Approved Makes: AtlasIED / Rittal / Valrack / President

VIDEO PROJECTION SYSTEM

Supply, Installation, Testing and Commissioning of LED Screen Size 8380 mm x 4800 mm or higher Pixel Pitch 2.5 mm or better (Lower is considered better) Expected resolution for the screen 256*192 Pixels or more LED type: SMD 2121 Video Support: 2K HD, 4K UHD Beam Angle Hor/Ver: 160°/140° or better Refresh Rate:4200 Hz or better White Balance Brightness: 6 00 CD /m 2 or higher Operation Temperature: -20ºc ~45ºc Working Humidity: 10% RH to 65% RH, non-condensing Contrast Ratio: 5000:1 or better Processing Depth: 12~14 B it Standard Color Temperature: 2000K to 9300K Adjustable Access For Maintenance Front Life Span (Hours) 100000 or more Support Single dot Brightness Calibration LED Spares 5% spare of total LED IP30 Rated Mandatory Certifications CE, FCC, BIS, UL/ETL or more Mounting Structure MS/Aluminum structure as per site requirement, 100% maintenance free, design flexibility, no affect by humidity & water durable to impact, no polishing required, including fastener/clamp etc. LED Controller Control port RJ45 / USB Video input type HDMI x 4 LED Output As per LED resolution Approved Makes: Samsung / LG / Panasonic.

Supply, Installation, Testing and Commissioning of 86" 4K UHD (3840 X 2160) LED display for Side walls of the auditorium, 500 Cd/m2, 2x HDMI input, RS232 and LAN Control, Approved Makes: Samsung/LG/Panasonic

Supply, Installation, Testing and Commissioning of Wall/Ceiling mount Bracket for above display. Approved Makes: Custom / apprv eqv

Supply, Installation, Testing and Commissioning of 43" 4K UHD (3840 X 2160) LED display for Confidence Monitor, 500 Cd/m2, 2x HDMI input, RS232 and LAN Control, with Standard Wall mount Bracket. Approved Makes: Samsung/LG/Panasonic

Supply, Installation, Testing and Commissioning of Floor mount Trolley for above display. Approved Makes: Custom / apprv eqv

Supply, Installation, Testing and Commissioning of 43" 4K UHD (3840 X 2160) LED display for Green Room, 500 Cd/m2, 2x HDMI input, RS232 and LAN Control, with Standard Wall mount Bracket. Approved Makes: Samsung/LG/Panasonic

Supply, Installation, Testing and Commissioning of 43" 4K UHD (3840 X 2160) LED display for Control Room, 500 Cd/m2, 2x HDMI input, RS232 and LAN Control, with Standard Wall mount Bracket. Approved Makes: Samsung/LG/Panasonic

Supply, Installation, Testing and Commissioning of Presentation Point of Wallplate HDBaseT Transmitter for HDMI and USB-C with USB Hub 2×1 switcher and HDBaseT transmitter with HDMI and USB-C inputs USB 2.0 and USB-C PC host interfaces, plus a USB 2.0 interface USB 2.0 interfacing and extension up to 330 feet 4K/UHD capability @ 60 Hz with 4:2:0 chroma subsampling HDCP 2.2 compliant Remote powering over HDBaseT Automatic display control TCP/IP and RS-232 control Multi-channel audio compliant EDID & HDCP Management Chroma Subsampling - 4:4:4, 4:2:0 Pixel Clock : 300 MHz or better Cable Link Monitoring: Integrated HDBaseT link status monitoring Enclosure: One / Two Gang for Wallplate Opening Approved Makes: Atlona /Extron / Lightware/Purelink

Supply, Installation, Testing and Commissioning of HDBaseT receiver for HDMI and USB Input Port: 1 x HDBT Output Port: 1 x HDMI Data Port: 2 x USB Hub or more Signal & Control Extension: Receiver for HDMI, Ethernet, power, control, and USB upto 100mtr using CATxx cable Resolution Support: 4K/UHD @ 60 Hz with 4:2:0 "USB : Signal - 2.0 or better Maximum Data Rate - 120 Mbps" Remote powering over HDBaseT or local powering Chroma Subsampling: 4:4:4 Color Depth: 8-bit, 10-bit, 12-bit HDCP 2.2 & CEC Pass-through Cable Link Monitoring: Integrated HDBaseT link status monitoring Approved Makes: Atlona /Extron / Lightware/Purelink

Supply, Installation, Testing and Commissioning of 1 x 4 HDMI Distribution Amplifier Input Port: 1 x HDMI Output Port: 4 x HDMI "Resolution Support: 4K/UHD @ 60 Hz with 4:4:4 " Power: Local AC powering LED Indicator: To provide power and output status information Chroma Subsampling: 4:4:4, 4:2:2, 4:2:0 Color Depth: 8-bit, 10-bit, 12-bit Support HDR10 Signal Bandwidth: 18 Gbps HDCP 2.2 HDCP Management, EDID Management Approved Makes: Atlona /Extron / Lightware/Purelink

Supply, Installation, Testing and Commissioning of 4K/UHD HDMI Extender Kit with Remote Power and control , Transmitter : Input Port: 1 x HDMI & Output Port : 1 x HDBT Receiver : Input Port: 1 x HDBaseT & Output Port : 1 x HDMI Signal & Control Extension: Transmitter for AV, Power & Control up to 70mtr using CAT6a/7 cable "Resolution Support: 4K/UHD @ 60 Hz with 4:2:0" Remote power, transmitter powers receiver over HDBaseT LED Indicator: To provide power and link status information HDBaseT link test verifies cable, termination, and link quality Chroma Subsampling: 4:4:4, 4:2:2, 4:2:0 Color Depth: 8-bit, 10-bit, 12-bit HDCP 1.4/2.2 HDCP 2.2 compliant and supports EDID filtering Bidirectional extension of both RS-232 and IR control commands Control: TCP/IP & RS-232 Approved Makes: Atlona /Extron / Lightware/Purelink

Supply, Installation, Testing and Commissioning of 4K/UHD HDMI Extender Kit with Remote Power and control , Transmitter : Input Port: 1 x HDMI & Output Port : 1 x HDBT Receiver : Input Port: 1 x HDBaseT & Output Port : 1 x HDMI Signal & Control Extension: Transmitter for AV, Power & Control up to 100 mtr using CAT6a/7 cable "Resolution Support: 4K/UHD @ 60 Hz with 4:2:0" Bidirectional remote power, transmitter powers receiver over HDBaseT LED Indicator: To provide power and link status information HDBaseT link test verifies cable, termination, and link quality Chroma Subsampling: 4:4:4, 4:2:2, 4:2:0 Color Depth: 8-bit, 10-bit, 12-bit HDCP 1.4/2.2 HDCP 2.2 compliant and supports EDID filtering Bidirectional extension of both RS-232 and IR control commands Control: TCP/IP & RS-232 Approved Makes: Atlona /Extron / Lightware/Purelink

Supply, Installation, Testing and Commissioning of PTZ camera 1080p 60Hz with 30X zoom. 60° horizontal field of view. Vertical FOV: 38.01° ~ 1.48°. Full HD resolution of 1920 x 1080p60 Output: 3G-SDI, HDMI, USB 2.0 (1080p30) and IP. Sensor: 1/3” CMOS, Shutter: Auto/ Manual. Scanning mode: Progressive/ Interlace. Backlight Compensation: supported, Digital Noise Reduction: 2D & 3D DNR, Signal Noise Ratio >55 dB. Horizontal rotation: -170° ~ +170°, Vertical rotation: -30° ~ +90°. Pan speed range: 1.7 ~ 120°/s. Tilt speed range:1.7 ~ 70°/s. H&V image flip: supported. Number of presets: up to 255. Control: UVC, IR Remote, IP, Serial. Network interface: RJ45 100 Mbit. Serial interface: RS232 mini DIN-8, RS485 2-pin phoenix. Included: Power adapter, remote control, RS232 cable, RS485 2-way Phoenix connector, Balanced Audio, Line-In Complete with mounting kit Approved Makes: Sony / Vaddio /Avonic

Supply, Installation, Testing and Commissioning of Compact PTZ camera controller. With this controller it is possible to control up to 255 camera’s and using up to 255 presets. The controller supports the Visca, Pelco-D and Pelco-P protocol and can be connected with RS232/485 as per the tender specifications. Approved Makes: Sony / Vaddio /Avonic

Supply, Installation, Testing and Commissioning of Wireless Presentation Platform for content sharing from up to four PCs or mobile devices,10/100/1000 Mbps, Wireless screen casting with iOS®, AndroidTM, Mac®, ChromebookTM, and Windows® devices through native AirPlay®, Google Cast, or Miracast protocols, Output - HDMI connector complete with standard accessories as per the tender specifications. Approved Makes: Atlona / Extron / Barco

Supply, Installation, Testing and Commissioning of Recording, Streaming & Webcasting Hardware simultaneously, Built-in 4 Inputs (HDMI /IP/3G-SDI/DVI) HDMI Out, Can record upto any three inputs simultaneously in a single frame and as well as individual sources simultaneously, Should have minimum 1TB inbuilt storage, Should be able to support minimum 3 unicast streams. Approved Makes: Extron / Lumens / Mediapointe

Supply, Installation, Testing and Commissioning of HDMI to USB 3.2 Gen 1 Video Capture Tool with Loop-Out. Conversion of HDMI 2.0b 18Gbps signals to 5Gbps. USB 3.2 Gen1 data. HDMI 4K 60Hz input with 1080p 60Hz downscaling support. Uncompressed YUV2 when using USB 3.2, MJPEG compression for USB 2.0. Compatible with VLC, OBS, XSPLIT, AMCAP and other video capturing software. Ideal for video conferencing, online streaming and other HDMI video capture scenarios. Approved Makes: Extron / Lightware/Atlona/Purelink

Supply, Installation, Testing and Commissioning of Network Based Hardware server gateways for AV system control AV asset management over the network PC Based Central Control, Monitor and Management (integrated or external). It shall be scalable to any size installation Built-In room management software GUI-based configuration platform Dual Gigabit Ethernet ports for isolating a dedicated AV LAN from the facility or corporate network RS232, IR and Relay ports provision through IP conversion points Supports industry-standard, network security features and protocols iPhone, iPad, and Android control app support Complete with User Interface License for Android and Apple devices. Approved Makes: Atlona /AMX/ Extron

Supply, Installation, Testing and Commissioning of Apple IPAD with table top docking station iPort for controlling to all equipment as per the tender specifications. Approved Makes: Apple + iPort equivalent

Supply, Installation, Testing and Commissioning of wooden Podium made of 19mm thick commercial board and matching laminates. The base of podium shall be 750x750mm, height 950 -1200mm with standard accessories as per the tender specifications. Approved Makes: MTS / AHA / Uni / equivalent

Supply, Installation, Testing and Commissioning of Wireless Router complete with standard accessories as per the tender specifications. Approved Makes: D link/Netgear/Linksys

Supply, Installation, Testing and Commissioning of 24 Port PoE1G Capable Network switch complete with standard accessories as per the tender specifications. Approved Makes: D link/Netgear/Linksys

Supply and Laying of Halogen-free 4K Premium High Speed HDMI Cable – 1.0m, HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz. Gold plated precision contacts with Secure-Lock. HDMI-A male to HDMI-A male, TPE outer jacket. High purity, tinned OFC copper conductors and triple shielding, AWG28. Halogen-free (LSZH) for low smoke emissions in case of fire. Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of Halogen-free 4K Premium High Speed HDMI Cable – 2.0m, HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz. Gold plated precision contacts with Secure-Lock. HDMI-A male to HDMI-A male, TPE outer jacket. High purity, tinned OFC copper conductors and triple shielding, AWG28. Halogen-free (LSZH) for low smoke emissions in case of fire. Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of Halogen-free 4K Premium High Speed HDMI Cable – 10.0m, HDMI version 1.4 – 10.2Gbps for resolutions up to 4K UltraHD 30Hz. Gold plated precision contacts with Secure-Lock. HDMI-A male to HDMI-A male, TPE outer jacket. High purity, tinned OFC copper conductors and triple shielding, AWG24. Halogen-free (LSZH) for low smoke emissions in case of fire. Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of USB 3.2 USB-C Cable with E-Marker – 2.00m. USB 3.2 (Gen 1x2) – 10Gbps data transmissio. Gold plated precision contacts. USB-C male to USB-C male. High purity copper conductors and triple shielding. USB Power Delivery 100W, DP Alt-Mode up to 8K 30Hz. Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of 2 M USB A-A Cable USB 3.2– 5Gbps data transmission, Gold plated precision contacts, USB-A male to USB-A male, High purity copper conductors and triple shielding Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of USB 2.0 USB-A to USB-B Cable, black, 2.0m, USB 2.0 - 480Mbps data transmission. Ultra flexible and compact cable and connector construction. USB-A male to USB-B male with blue strain relief. High purity copper conductors and graphene nano shielding. Power transmission with max. power output 2A / 5V / 10W. Approved Makes: Purelink / Extron / Atlona / Lightware

Supply and Laying of CAT6 shielded twisted pair cable. Approved Makes: Extron / Sommer / Panduit / Commscope / Siemon

Supply, Installation, Testing and Commissioning of Customized Floor Box with Cutout for HDBaseT Transmitter plate for podium and 1x XLR female Connector for Microphones Connectivity and and 1x 15 Amp. Universal power Socket Complete with standard accessories as required. Approved Makes: Custom / apprv eqv

Programming of Audio, Video & control systems, operating the system for 1 year and training to college technical staff for operating the system by including AMC .

MISCELLANEOUS CIVIL WORKS

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing Table in Control room of top counter size 750 mm D x 2700 mm L x 900 mm H, made out of 19 mm thick MR grade block board on top and end supports, finished with 1 mm thick laminate with under counter storage cabinets 600 mm wide on both sides. Both cabinets will have 2 nos of Drawers each of equal ht with slide channels, handles, locking arrangements, internal laminate finish, complete as directed.

Providing and fixing 900-1000mm high stainless steel railing on steps and on stage ramp, made with SS304 garde steel. The railing consists of 62mm dia top rail, 50mm dia balustrades, SS plate grouted to floor with steel fasteners etc. complete. The railing to be buffer polished on welding joints to match the colour. All complete as per the design and drawings.

Providing and fixing SS hand rail consisting of 50 mm dia SS304 Grade pipe welded with 150 mm long SS supports made of 40mm dia pipe. The SS pipe support to be fixed to bed with SS plates/cleat. All complete as per the design and drawing.

Providing and fixing 16mm thick HDHMR board with 1mm thick laminate fixing on both sides in required pattern including providing egde binding in matching shade.

Providing, erecting and dismantling of complete scaffolding with platform in the auditorium for the complete duration of work. The scaffolding to be used by all the agencies working in the auditorium & Will be Paid one time during the construction period.

ELECTRICAL & GENERAL ILLUMINATION SYSTEM

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C. ; Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,; Switch Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required ; Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,; Switch Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 6 sq. mm + 2 X 6 sq. mm earth wire. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 10 sq. mm + 2 X 6 sq. mm earth wire. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 16 sq. mm + 2 X 6 sq. mm earth wire. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel / PVC conduit as required. 2 x 1.5 sq. mm. Wire Make: -Havells ,KK kable, Polycab, Finolex. ; Conduit Make:- Supreme, Prakash, Setia,;

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm Conduit Make:- Supreme, Prakash, Setia,;

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm. Conduit Make:- Supreme, Prakash, Setia,;

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm Conduit Make:- Supreme, Prakash, Setia,;

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 3 pin 5/6 amp socket outlet ; Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole Switch & Socket Make:- Anchor Roma, North West, Norsis Havells, Legrand.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutra. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 amps. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps. Make:- Legrand, Siemens , ABB, C & S.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door. Make:- Legrand, Siemens , ABB, C & S.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door. Make:- Legrand, Siemens , ABB, C & S.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Make:- JMV, As Per CPWD Norms.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Make:- JMV, As Per CPWD Norms.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ELECTRICAL & GENERAL ILLUMINATION SYSTEM

Supply installation testing & commissioning of a 1 x 20 kVA True On-line UPS system suitable for 415V 50 Hz 3 phase input, 415V 50 Hz 3 phase output along with individual battery bank in battery cabinet suitable for 15 minutes backup for 100% load, complete with full microprocessor control etc. and complete as required

Supply installation testing & commissioning of a 1 x 2 kVA UPS system suitable for 230V 50 Hz 1 phase input, 230V 50 Hz 1 phase output along with individual battery bank in battery cabinet suitable for 15 minutes backup for 100% load, complete with full microprocessor control etc. and complete as required

SITC of 4 channel Analog power supply (0-10V) LED dimmers suitable for switching module with 10A in each channel and upto 25 nos. of LED 40 W with dimming range of 0-100 percent. i/c incorporating sensors on the unit itself and have RS485 port., programmable from a handheld device / phone and suitable for Input voltage of 230V, 50Hz etc. as reqd. (Lutron/Zumbotel/TRILUX )

SITC of control wall station with 8 buttons and also to raise lower functionality. The buttons should be programmable to recall any preset scene / zone as per desired functionality. ( Lutron/ Zumbotel/TRILUX)

SITC of Central Processor for Creating Scenes and Time Control. It needs to have a capability to Integrate on IP protocol. (Lutron/Zumbotel/TRILUX)

Supply and installation of 18W LED recessed mounted down lighter with DALI dimmable driver Crompton/ phillips / wipro / bajaj

Supply and installation of 20W LED recessed mounted down lighter with DALI dimmable driver Crompton/ phillips / wipro / bajaj

Supply and installation of 20W LED recessed mounted down lighter with driver Crompton/ phillips / wipro / bajaj

Supply and installation of Self contained single sided exit sign green in color for wall / ceiling / pendant cantilever mounting with 3W LED with maintenance free battery with backup 2-3 hours duration, connection testing etc. as reqd

Supply and installation of 12W LED recessed mounted down lighter Crompton/ phillips / wipro / bajaj

Supply and installation of 75mm wide & 1000mm long made out of extruded aluminium in step corner form with 15-20mm overhang over the raiser. Consisting of 1W LED fixed at top with acrylic sheet having chair number embossed on it. The down nose to have 6 nos 1 watt LED to illuminate the step riser. Make Plantion, Phillips

Supply and installation of 12V Drivers for step lights, profile lights and led light 10 nos step lights

Supply and installation of LED Cove lights for ceiling. Led tape 6 W/m with driver. Make: Philips, Bajaj, Havells

Supply and installation of 12V profile lights in ceiling with 3000k temperature. The profile lights to be fixed in false ceiling after making necessary cuttings and making good the same.

Supply and laying of XLPE insulated power cable conforming to IS-7098 1.1kV volt grade/ Heavy duty power cable conforming to IS 1554-1100 volts grade Armoured 3.5 Cx 240 Sq.mm

Supply and installation of LT straight through cable jointing Kit for 1.1 kV grade LT cable of size 3.5 C x 240 sq.mm Al conductor XLPE insulated FRLS power cables

Supply and installation of 600 mm Air Circulator Wall Fan of size: 24 Inch, power Supply : 230 V, power 180Watt, Speed (RPM) : 1440.0. Vertical adjustable, Aluminium alloy one piece blade, Double ball-bearing 90 oscillation, Sturdy close-mesh guard beautiful design, Powerful heavy-duty motor. The fans to be fixed with base plate on existing walls including making frame etc. complete..

Lighting Distribution board

SITC of Power Distribution Electrical panel on stage and control room having a incomer of 63A floor mount / rack mount / wall mount with nuetral separation made using incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization, individual MCB control for 28 outgoing circuits, separate incomer control for Motor control panel supply, RYB Phase indicators internally wired using IS certified wires and cables, provided with ivery connectors for the internal terminations and external outgoing connecting points custom built as per specification and project requirement. Approved makes: Leksa Lighting / New Age / Lyt Master

Supply and laying of following size of 1.1kv grade multicore copper conductor XLPE insulated and PVC sheathed armoured cable as per IS : 7098:1988(Part - I) with upto date amendments. 4C x16sqmm

Supply and laying of following size of 1.1kv grade multicore copper conductor XLPE insulated and PVC sheathed armoured cable as per IS : 7098:1988(Part - I) with upto date amendments. 4C x10sqmm

Supply and laying of following size of 1.1kv grade multicore copper conductor XLPE insulated and PVC sheathed armoured cable as per IS : 7098:1988(Part - I) with upto date amendments. 4C x6sqmm

Supply and making and termination with flame proof brass compression gland and copper thimbles 4 XLPE insulated and PVC sheathed copper Condutor cable off 1.1 kV grade of the following sizes as required. 4C x16sqmm

Supply and making and termination with flame proof brass compression gland and copper thimbles 4 XLPE insulated and PVC sheathed copper Condutor cable off 1.1 kV grade of the following sizes as required. 4C x10sqmm

Supply and making and termination with flame proof brass compression gland and copper thimbles 4 XLPE insulated and PVC sheathed copper Condutor cable off 1.1 kV grade of the following sizes as required. 4C x6sqmm

FIRE FIGHTING & FIRE ALARM SYSTEM

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :. (Make - Jindal, Tata)

150 mm Dia

100 mm Dia

80 mm Dia

50 mm Dia

32 mm Dia

25 mm Dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

150mm Dia

100 mm Dia

80 mm Dia

SITC Gun Metal Ball Valve 25 mm dia (PN 25) as complete with 25 mm sight glass bye pass arrangement, (Make - Zoloto. ITAP, RB, CIM)

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories Make:- Tyco, Viking, CIM, ITAP, Zoloto .

Pendent Sprinkler

Upright Sprinkler

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

150 mm dia

FIRE EXTINGUISHERS

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.

ISI marked (IS:15683:2006) Carbon-did- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & horn, wall mounting bracket/Floor tralley and suitable sinages etc. complete, confirming to IS: 2878. (Make - SAFEX, KANEX, safe guard/OMEX/Life Guard )

ISI marked (IS:15683:2006) ABC type type fire extinguisher of 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure CO2 gas cartridge, discharge hose, wall mounting bracket,complete, confirming to IS:2171. (Make - SAFEX, KANEX, safe guard/OMEX/Life Guard )

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required . Make:- Jindal, Tata.

100/80 mm dia

150 mm dia

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. (Make;- Ploycab/Havells/RR/KEI )

AUTOMATIC FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. Make:- Agni/ ASE/ Safe Zone

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required. Make:- Agni/ ASE/ Safe Zone

Supplying, installation, testing & commissioning of addressable manual call point complete as required. Make:- Agni/ ASE/ Safe Zone

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required . Make: Agni/ ASE/ Safe Zone

Supplying, installation, testing & commissioning of addressable fire control module complete as required. Make: Agni/ ASE/ Safe Zone/ Honeywell

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

PA System

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Make;- AHUJA/ AGNI/ Honey well

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supply, Installation, Testing and Commissioning of 20U Equipment Rack on stage for housing all rack mountable equipment with front glass door, heat dissipation fans, internal lights, movement wheels, power distribution units etc. complete with standard accessories. Approved Makes: AtlasIED / Rittal / Valrack / President

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required. Make;- AHUJA/ AGNI/ Honey well

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure, all complete as required. Make;- AHUJA/ AGNI/ Honey well

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. Make- Siemens, L & T

NEW AGE ACOUSTICS PVT LTD (BID ID -3240596)