PROVN OF BOUNDARY WALL AT EXTENDED PORTION, PARKING SHED AND ADDN/ ALTN TO BLDG AT VARIOUS LOCATIONS OF AF STN WADSAR UNDER GE (AF) CHILODA

Amount

Surface dressing n. exc. 15cm deep and getting out in soft/ loose soil complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and gettting out in soft/ loose soil all as sepcified and as directed.

Excavation in trenches n. exc. 1.50m wide and n. exc. 1.50m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Excavating in post holes each n. exc. 0.5 Cum getting out in soft/ loose soil and removing surfaces soil to a distance n. exc. 50m and making good surfaces complete all as specified and as directed.

Returning, filling in including spreading, levelling, filling in trenches n. exc. 25cm each layers of soft and loose soil etc. complete all as specified and as directed.

Removal of excavated materials exc. 1.50 KM and n. exc. 5 KM depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed.

Removing excavated materials not exceeding 50 mtrs away and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

M&L for PCC (1:4:8) Type D2 (using 40 mm graded stone aggregates) in foundation, filling and mass concrete complete all as specified and as directed.

M/L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation of posts and pillars etc. complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base complete all as specified and as directed.

M&L for RCC M-25 (design mix) as in foundation including rafts, footings, foundation beams, plinth beams, bases for column etc. complete all as specified and as directed.

M&L for RCC M-25 (design mix) (using 20mm graded aggregated) as in columns, pillars, piers, post and struts etc. complete all as specified and as directed.

M&L for RCC M-25 (design mix) (using 20mm graded aggregated) as in beams, top hand, cantilevers measurers lintel over 1.50m span complete all as specified and as directed.

M&L for RCC M-25 (design mix) (using 20mm graded aggregated) as in chajjas etc. complete all as specified and as directed.

M&L for RCC M-25 (design mix) (using 20mm graded aggregated) as in slab supported on walls, roof beams and columns in floors, deck slabs and in shelves etc. complete all as specified and as directed.

Use and waste of formwork to soffit of suspended slab as roof slabs, floor slabs, landing and similar work n. exc. 200mm thick, rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or batter complete all as specified and as directed.

Use and waste of formwork to sides of concrete of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beam hunching girders measurers, lintels, cantilevers, shelves etc including supports of beam also and plashes between floor beam etc. complete all as specified and as directed.

M&L for mild steel TMT bar in reinforcement 10mm dia and over cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mils steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F mild steel TMT bars 6mm dia over upto and including 10mm dia in stirrups, spaces and binders and over, cut to length, bent to shape required, and hooking ends and binding with and including mild steel wire (annelaed) not less than 0.9mm dia complete all as specified and as directed.

M&L for pre-cast cement concrete (1:3:6) type C1 (using 20mm graded stone aggregates) set in cement mortar (1:6) solid block masonry with solid blocks, exc. 10cm in width and setting in mortar, complete all as specified and as directed.

M&L for prepration of new plastered surfaces of wall and applying two coat of cemenrt base paint over a coat of primer complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6.00 m mean radious and built in CM (1:6) complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for treatting the top surface of filled earth of flooring and under plinth protection at the rate of 5 ltrs of emulsion per sqm of surface area complete all as specified and as directed.

M&L for treatting the soil along with external perimeter of building at the rate of 2.5 ltrs of emulsion per sqm of perimeter wall complete all as specified and as directed.

M&L for hard core of gauge n. exc. 63mm deposited, spreaded and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface of broken stones or boulders etc. complete all as specified and as directed.

M&L for 100 mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base of flooring complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:3:6) type C2 (using 40mm graded stone aggregates) as in plinth protection finishes even and fair without using extra cement finishing exposed edges fair for rounding and in phase every 2 mtr for length and joint shall be finsihed with bitumen and sand mixtures (1:3) complete all as specified and as directed.

M&L for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces mixed with water proofing compound including finishing the surface even and smooth without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on brick walls finishing the surface even and smooth (without using extra cement) etc. complete all as specified and as directed by EIC.

M&L for rendering 5 mm thick in CM (1:3) on ceiling surfaces, finishing the surface even and smooth (without using extra cement) etc. complete all as specified and as directed by EIC.

M&L for 20mm thick screed bed or bedding layer in cement morter (1:4) for laying floor finishes complete all as specified and as directed by EIC.

M&L for virified ceramic tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and as directed.

All as per Item No. 36 above but in skirting including 15mm thick backing coat in CM (1:4) complete all as specified and as directed.

M&L for aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92mm x 31.75mm x 1.50mm (section No 20831), bottom size 92mm x 31.75mm x 1.50mm (section No 20832) and shutter top & bottom of size 40mm x 18mm x 1.55mm (section No 20736) and sides (handle) of size 40mm x 18mm x 1.55mm (section No 20738) and lock side shutter frame of size 40mm x 18mm x 1.45mm (section No 20737)" with rubber gasket, beading and locking arrangement and rollers etc. including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc. complete all as specified and as directed by Engr-in-Charge.

S&F 30mm thick, first class hard wood, moulded, moulded both sides and framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

S&F 100mm cold rolled mild steel butt hinges heavy duty with screws and fixed to door/ welded to door complete all as specified and as directed.

S&F 200mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruted section or cast aluminium alloy and fixed length of bolt 300mm complete all as specified and as directed.

S&F 150mm long aluminium handle cast type anodized complete all as specified and as directed by Engineer-in-Charge.

S&F framed brackets of angles or tees with web and flanges, purlins etc, cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc n. exc. 10 kg each brackets conforming to Fe 290 Gde-E-165 as in cooler stands and other similar works etc. complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane, gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc and similar work confirming to Fe 290. Gde -E-165 complete all as specified and as directed.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surface of any description not otherwise described over 10cm width or grith not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L for applying cold bituminous primer @ 0.30 Ltr/ Sqm conforming to IS : 3384 laying APP polymer modified membrane 3.6 to 4.0 Kg/Sqm in weight with non-woven polyster reinforcement (mineral gravel finish on upper side of the membrane) and sealing all overlaps of 100mm in length side and 150mm on width side of membrane by torching the same as per manufacture instruction and all as per specified particular specification and including 10mm thick screed bed in CM (1:3) mixed with WPT 3% by weight of cement complete all as specified and as directed.

M&L for preparation of newely plastered surfaces of wall and applying two coats of oil bound distemper over 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of newely plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

S&F aluminium composite panel 3mm thick exterior grade PVDF with foil thick of 0.25 mm & frame work Made out from aluminium section of size 38x25mm supported on masonary/ RCC with the help of MS bracket fixed with brick fastener/ anchor fastner and groove filled with 789 weather sillent of DOW corning etc. complete as per architect drg and as per direction of Engr-in-Charge.

M&L for provission of false ceiling at height of 600mm x 600mm x 15mm mineral fibre ceiling tiles RH-99 of type micro looks edge laid on super fine XL 15mm expose d grid systems with 15mm wide T- section flanges. The frame work comprises of main runner of size 15x32x3000 mm spaced at 1200mm centre securing fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers (GI wire of 4.0mm dia) to be fixed by approved roof plug, level adjusters and screws etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall flush fitting 1200mm long cross tees of size 15x26x1200 mm to be interloched between main runners at 600mm centers to form a 1200mm x 600mm module. Cut cross tees longer than that 600mm to be supported independently. 600mm x 600mm modules to be formed by fitting 600mm long flush fitting cross tees of size 15x26x600 mm centrally between the 1200mm crosstees perimeter wall angle of size 19x19x3000 mm secured to wall at 450mm maximum centres. Finally RH-99 mineral fibre tile 15mm thick micro look edge has to be laid on the 600mm x 600mm module as approved by GE complete all as specified and as directed.

M&L PVC SWR pipe 110mm bore single socket in any length with rubber ring joint laid in wall or floor complete all as specified and as directed.

M&L for 25mm thick pre-formed filler for expansion joints complete all as specified and as directed.

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment etc complete all as specified and as directed.

M&L for concealed point wiring complete with FRLS PVC insulated/ unsheathed stranded copper conductor of wire 1.5 Sqmm, 1100 Volt grade, alongwith one single core of same size stranded copper as continuous earth wire to common earth dolly in and including PVC conduit pipe fitting medium grade of 25mm dia fixed in concealed surface of wall/ ceilling/ false ceilling including cutting/ chasing in wall as required with powder coated sheet metal terminal boxes modular type of required sizes and thickness (factory made) sunk in wall where as required and accessories complete suitable for one light/ fan point controlled by one one way switch complete all as specified and as directed.

All as per Item No. 58 above but one socket outlet 05 Amps on the same board.

All as per Item No. 58 above but one socket outlet 05 Amps on independent board.

All as per Item No. 58 above but one bell point controlled by one push button.

All as per Item No. 58 above but point wiring with 2.5 Sqmm cable and 2.5 Sqmm earth continuity conductor for 3 pin 15 Amp socket.

All as per Item No. 58 above but point wiring with 4.0 Sqmm cable and 4.0 Sqmm earth continuity conductor for 3 pin 15 Amp socket.

S&F modular switch, one way, 6 Amps, 1 module, ISI marked complete all as specified and as directed.

S&F modular socket, 6 Amps, 2/ 3 pin, combined, 2 module, ISI marked complete all as specified and as directed.

S&F modular socket, 6/ 16 Amps, 2/ 3 pin, combined, 2 module, ISI marked complete all as specified and as directed.

S&F modular switch, one way, 16/ 20 Amps, 1 module, ISI marked complete all as specified and as directed.

S&F modular bell push, 6 Amps, 1 module, ISI marked complete all as specified and as directed.

S&F modular fan step regulator, 120 W, 1 module, ISI marked complete all as specified and as directed.

S&F modular white cover plate with frame, 1 module, ISI marked complete all as specified and as directed.

S&F modular white cover plate with frame, 4 module, ISI marked complete all as specified and as directed.

S&F modular white cover plate with frame, 8 module, ISI marked complete all as specified and as directed.

S&F ceiling fan, complete with three blade, down rod, accessories 230 V, 1200mm sweep, with squirrel cage induction motor complete all as specified and as directed.

S&F on wall, plug and socket in sheet steel enclosure with single pole & earth, suitable for 20 Amp with providing MCB SP 20 Amp suitable for single phase AC supply complete all as specified and as directed.

S&F LED light fitting 1x9 W/ 1X10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F ceiling rose, 5 Amps surface type 240 Volts bakelite three terminal complete all as specified and as directed.

S&F 8 way sheet metal enclosures for flush/surface mounting distribution board double door, 240 Volts factory made and tested complete, suitable for mounting MCBs with 200 Amps rated bus bar, cable lugs complete all as specified and as directed.

All as per Item No. 77 above but 4 way, 415 Volts TPN DB.

S&F 240 V, 10 KA, 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

SP 5 To 32 AMP.

SPN 32 AMP.

SPN 40 to 63 AMP.

S&F MCB TPN 40 to 100 AMP, 415 V, 10 KA, 'C' curve in the DB with connection testing and commissioning complete all as specified and as directed.

S&F LED luminaire 600mm x 600mm, 35/36 Watt, 220 V, AC recessed type with highefficiency PMMA diffuser soft glare free light completewith driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F round shape 6 Watt, 220 Volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and laying or fixing XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (H/D) earthed cable aluminium conductor, 1100 Volts grade with stranded of size 16 Sqmm, 4.0 Core nominal cross section in service connections complete all as specified and as directed.

M&L for old size, burnt brick, sub class 'B', laid in trenches, abutting each other with a gap not exceeding 10mm, vertically over the cable for cable protection complete all as specified and as directed.

Navkar Enterprises

DMA PROJECTS