Construction of Multipurpose hall of COH and F Thunag at Atal adarsh Vidyalaya Gudeheri Gohar Distt Mandi remaining items thereof SH building portion water supply and sanitary installation

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas in all width including getting out and disposal of excavated earth all leads, lifts and carriage of material as directed by the Engineer-incharge a)Ordinary rock.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete in all respect as per satisfaction of Engineer-in-Charge

Providing and laying in position cement concrete of 1:5:10 (one Cement : five sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size excluding the cost of centering and shuttering - All work up to plinth level complete in all respect as per satisfaction of Engineer-in-Charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (one cement : three sand (zone - III) : six graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one & half coarse sand : three graded stone aggregate 20 mm(twenty milimetre) nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge.

a). Suspended floors, roofs, landings, balconies and access platform

b). Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-charge a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth level with Cement mortar 1:6 (one cement : six sand) complete in all respect as per satisfaction of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:6 (one cement : Six sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Brick edging 7 cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (one cement : four sand) complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all levels etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Granite of any colour and shade Area of slab 0ver 0.50 sqm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 35 mm ( Thirty five milimetre) thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked 85x42 mm oxidized M.S. pull bolt lock conforming to IS: 7534 with necessary screws bolts, nut and washers etc. complete. in all respect as per satisfaction of Engineer-in-Charge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 25 mm dia heavy type Nickel plated M.S. pipe curtain rods with nickel plated brackets etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providind and fixing ISI marked MS pressed butt hinges bright finished with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) 125x65x2.12 mm

Providing and fixing ISI marked oxidised / chromium plated M.S. sliding door bolts with nuts and screws etc. complete :etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 300x16 mm (three hundred into sixteen milimetre)

b)250x16mm(two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized / chromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm(two hundred into ten milimetre)

b). 150x10mm(one hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). .125mm (one hundred twenty five milimetre)

b). 100 mm ( one hundred milimetre)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Single rubber stopper.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ), with necessary accessories and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. double acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre)

Steel work in built up tubular (round, square or rectangular hollow GI tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete in all respect as per satisfaction of Engineer-in-charge a). Hot finished welded type tubes.

MS square/ rectangular hollow pipe welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using tube etc. as required. Complete in all respect as per satisfaction of Engineer-in-Charge. a).In gratings, frames, guard bar, ladder, grills, railings, brackets, gates and similar works..

Providing and fixing fly proof wire gauge to windows, clerestory windows and doors with MS flat 15x3 mm and nuts & bolts complete complete in all respect as per satisfaction of Engineer-in-Charge. a). Galvanised MS wire gauge with 0.63 mm dia wire and 1.4 mm aperture on both sides..

Providing & fixing 4.0 mm ( four milimetre) thick glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all etc. complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). a) Fixing without 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing MS channel/ Angle/Tee iron frames manufactured for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges, beads,screws if required and provision of locking arrangement and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge .a). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge a)25 mm thick (twenty five milimetre).

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (one cement: three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing etc. complete in all respect as per satisfaction of Engineer-in-charge.

Extra for pre finished nosing in treads of steps of kota stone slab etc. complete in all respect as per satisfaction of Engineer-in-charge

Providing and laying JointlessCeramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc complete in all respect as per satisfaction of Engineer-in-Charge (Kazaria / Nitco / Oreintbell / Somanymake).

Grouting the joints of flooring Kota/tiles 300 into 300mm size having joints of 3 mm width in different size of tiles/ Kota stone, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing etc. complete as per the satisfaction of Engineer-in-charge.

Providing and fixing jointless Ist quality ceramic glazed wall tiles (Kazaria / Oreint bell / Nitco/ Somany make) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete in all respact as per direction of Engineer-in- Charge

Providing and laying Antiskid vitrified floor tiles full body in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of Kazaria/ Nitco/ Orient bell/ Somani make in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Size of Tile 600x600 mm.

Chequerred precast cement concrete tiles 22 mm thick (ISI make) in footpath & courtyard, jointed with neat cement slurry mixed with dark pigment shade to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm using ordinary cement thick bed of cement mortar 1:4 (one cement: four sand) required etc. complete in all respect as per direction of Engineer-in-Charge a). Dark shade pigment using ordinary cement

Providing and fixing precoated galvanised steel sheet Ridges plain (500 - 600mm) 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete in all respect as per satisfaction of Engineer-in-Charge .(Tata/ Jindel/ JSW make)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Tata/ Jindel/ JSW make)

Providing and fixing plain multipurpose cement board (Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete in all respect as per satisfaction of Engineer-in-Charge (frame work to be paid seperatately). a). 6 mm thick Cement fiber board as per IS: 14862

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.32 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Tata/ Jindel/ JSW make)

6 mm (six milimetre) thick ceiling plaster with cement mortar 1:3 (one Cement: three sand) complete in all respect as per satisfaction of Engineer-in-Charge.

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:6 (one cement: six sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint on new wood/steel of approved brand and manufacture to give an even shade as required complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge. a)Two or more coats on new work

Finishing walls with Acrylic Smooth exterior paint of required shade with New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads etc. complete as per direction of Engineer - in – charge. a). Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevation area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding.

Providing and laying 60 mm (Sixty milimetre) thick factory made interlocking paver block of M-30 grade (ISI Make) made by block making machine with strong vibratory compaction of approved size, design & shape laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. Complete in all respact as per direction of Engineer-in- Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera/ Hindware make). a) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm PVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge. (Cera / Hindware make). a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make). a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto one metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing 32mm dia Semi rigid pipe P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete in all respect as per satisfaction of Engineer-in-Charge..

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing PTMT 15 mm dia Urinal spreader size 95x69x100 mm with 1/2” BSP thread and shapes, weighing not less than 60 gms. Etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing internal work- exposed on wall for Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. a) 20 mm(Twenty milimetre) nominal outer dia Pipes.

Providing and fixing 40 mm dia nominal bore G.I. pipes (medium grade) complete with G.I. fittings including trenching and refilling etc. complete in all respect as per satisfaction of Engineer-in-charge (Jindal/ Surya make).

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: in all respect as per satisfaction of Engineer-in-Charge. a) 25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 20 mm (twenty milimetre) nominal bore

b). 40 mm (forty milimetre) nominal bore

Providing and fixing 45 cm length and 15 mm nominal dia uplasticised PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 Sintex marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Sparton/ Seiko/ smile/ Czar make).

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ Czar make).

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ Czar make).

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one & half coarse sand (zone- III) : three graded stone aggregate 20 mm(twenty milimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm(forty milimetre) nominal size), inside plastering 12 mm thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement :two coarse sand : four graded stone aggregate 20 mm(twenty milimetre) nominal size) finished with a floating coat of neat cement complete as per standard design complete in all respect as per satisfaction of Engineer-in-Charge. a). Inside size 900x800mm and 450mm deep including 450x610mm dia opening (medium duty) SFRC Man hole cover with frame. ) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Extra for depth for manholes With common burnt clay F.P.S. (non modular) bricks of class designation 7.5etc. complete in all respect as per satisfaction of Engineer-in-charge. a)Size 90x80 cm

Cutting holes up to 30x30 cm in walls including making good the same with common burnt clay F.P.S. (non modular) bricks complete in all respect as per satisfaction of Engineer-in-Charge

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (one cement: two sand : four graded stone aggregate 20 mm (twenty milimetre)nominal size including finishing complete so as to make it leak proof etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 32 mm dia C.P. brass waste for wash basin or sink complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing C.P. brass Towel rail complete with C.P. Brassbrackets fixed to wooden plugs with C.P. brass complete in all respect as per satisfaction of Engineer-in-charge .a) 600x20mm size

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing vitreous China division plate for urinal complete in all respect as per satisfaction of Engineer-in-charge (Cera / Hindware make). a) 600mmx330mm size

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make).a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre)

b). 110mm ( one hundred ten milimetre) dia

b). 150 mm ( one hundred ten milimetre) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in charge (Finolex/Kisan/D-plast make).

a) 75mm (Seventy five milimetre ) dia

b) 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC single equal branch plain ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a) 75mm (Seventy five milimetre ) dia

b) 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b) 110mm ( one hundred ten milimetre) dia

b) 150mm ( one hundred fifty milimetre) dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )diaa

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC door bend with oval access door insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc complete in all respect as pcomplete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing 150mm (One hundred fifty milimetre)CP M.S. Hooks and eyes etc. complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing 30 mm thick factory made single extruded WPC (Wood polymer composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 grm) having minimum density of 650 Kg/ cum and screw withdrawl strength of1800 N (Face) & 900 N (Edge), minimum compressive stren 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in- Charge. ( Stainless steel butt hinges and necessary SS screws shall be paid separately).

Providing and fixing PVC gully trap with grating brick masonry chamber in cement mortar 1:5 and water tight SFRC cover with frame of 300mmx300mm size (inside) and 40 mm thick etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). A) 110mm dia P type.

Providing and fixing vitreous China ½ stall urinal including connecting the urinal with water pipe by means of white lead mixed with chopped hemp (waste to measured and paid separately) complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware/ Jaquar make. a) Half stall urinal flat back size 535 into 355 into into 340 mm

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a)110mm P dia.

a). 75mm (Seventy five milimetre )dia

b). 110mm ( one hundred ten milimetre) dia