SITC of Electrical panel for Container type Security Cabin

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 2.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt) as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Above 35 sq. mm and upto 95 sq. mm

Supply of LED Flood Light with a minimum system lumen of 7000 Lumen and system wattage not exceeding 72W with a nominal efficiency 90 lumen/watt .The Luminaire should be having Minimum 50000 Burning hours(L70B50). The housing should be of Single piece non-corrosive ADC12Grade high-pressure die-cast aluminum and should have corrosion resistant coating to pass Natural salt spray test of 500 Hrs with IP66 Protection. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs , should have an auto shutdown at 325V and have an auto recovery feature , Under Voltage protection with Input Voltage Stress of 100V for 48 Hrs, PF > 0.95 and THD<10 %.The Luminaire should have a 10 KV SPD duly bolted in the Luminaire,SPD should be able to sustain a minimum 15 hits of 10KV rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2 .The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire,PF>0.95 and THD<10% . Luminaire and driver shall be separately BIS approved of same make equivalent to Philips BVP120 LED047 CW FLNB FG A1 PSU GR. LM80,LM79 ,Type Test certificate and Bis certificate need to be submitted. Including all necessary equipments for installation.

Supplying installation, testing and commissioning of free standing out door compartmentalized cubicle feeder pillar type panel suitable for 415 V, 3phase, 4 wire 50Hz AC supply system fabricated in CRCA sheet steel of 14 gauge thick, with hinged double leaf shutters with pad locking arrangement, detachable gland plates of suitable size at the bottom for cable entry, and busbar chamber with tinned copper bus bar of 100A capacity, handle, gaskets etc. with sloped roof, including powder coat painting in approved shade, ISMC channel at bottom, entire panel shall have a common tinned copper earth bar of size 20 mm x 3mm at the rear with 1 no 100 A 4 P MCCB, 1 no 63 A 4 P RCCB, 1 no 63 A 4P MCCB, 2 no 32 A 4P MCCB, 4 no 25/20 A 4P MCCB, 1 no 20 A MCCB with digital timer, 2 nos earth stud, solid connections from switch gears with required size of copper wire, control wiring with 1.5 sq.mm PVC insulated copper conductor cable, cable alleys, cable gland plates etc including indication lamps, digital type Multi function meter suitable CTs, SPD type 1&2 with back up fuse, danger notice board, LED indicator, feeder compartment lock, terminal block, PVC trunking, slotted channel, suitable connector, termination lug, copper wire if required, meter viewing glass if required etc.. Insulated copper bus bar for phase and Neutral adequate ampere size of Incomer Switch , out going switches. The panel Board should be fitted on the base frame for panel board using channels of class designation 75 including cutting,welding, drilling holes,painting two coats of synthatic enamel paint over a coat of zinc chromate paint botling the frame to the panel and to the furnished floor using required bolts and nuts making good the dameges colour washing and including providing and fixing the following switch gears etc as required.The charges for all control wiring, loading and unloading, testing and commissioning are included. The cable entry may be bottom or top as per direction of Engineer in charge, The Panel shall be Fabricated as per Electrical Inspectorate, KSEB, CPRI & other relevent codes and standards. Including proper labeling of cable entry, outgoing etc. With appropriate drawing (CAD file) and documentation for electrical inspectorate approval for load addition and energisation as required complete, including charges/ fee for application to KEI.

Supply and laying one number of the 8 SWG good quality bare copper wire for earthing from earth electrode to security container cabin recess of minimum 60 cm below the ground for connections etc. as required.

Charges for removing metal enclosures with MCB & other accessories without any damage and making good the damages of the wall including painting, etc. as required.

Supply of suitable amount (60kg) of earthing compound (EXCEL compound or equivalent) etc. as required.

Supplying and fixing 130 x 180 x 77 mm or nearest size water proof rigid polycarbonate loop in loop out weather proof box (IP 66) with detachable front cover, including supply & fixing 4 way busbar connector with base insulator, fixing 6 A SP MCB, fixing on the surface using suitable size metal screws, giving connections and other accessories as required.

Supply and laying one number of the 6 SWG good quality bare copper wire for earthing from earth electrode to security container cabin recess of minimum 60 cm below the ground for connections etc. as required.

Please Enable Macros to View BoQ information