SEE Div. : Renovation of SM panel room at stations over Sonpur division.

as per (Schedule -A), Annexure "A-1" except steel Reinforcement.

All Items in connection with works under CPWD-DSR-2021 with upto date corrections as per

(Schedule -A), Annexure "A-1" except steel Reinforcement.

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding

1.5 m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, lift

upto 1.5 m, including getting out the excavated

soil and disposal of surplus excavated soil as

directed, within a lead of 50 m.

2.25 Filling available excavated earth (excluding cum 480 253.95 121896

rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming

and watering, lead up to 50 m and lift upto 1.5

2.27 Supplying and filling in plinth with sand under cum 240 2161.2 518688

3 floors, including watering, ramming,

consolidating and dressing complete.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering - All work up to

derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCED CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified grade

of reinforced cement concrete, excluding the

cost of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

derived from natural sources: 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five

level, excluding cost of centering, shuttering,

finishing and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non

6.1 modular) bricks of class designation 7.5 in

foundation and plinth in:

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

level in all shapes and sizes in :

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay

6.12 F.P.S. (non modular) bricks of class designation

7.5 in foundations and plinth in :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to

8.0 CLADDING WORK

8.20S STONE WORK DRY CLADDING

Providing and fixing in wall lining flat pressed

three layer (medium density) particle board or

graded wood Pre-laminated one side decorative

8.26 lamination and other side balancing lamination

Grade I, Type II, IS : 12823 marked, including

priming coat on unexposed arrangement and

screws etc. complete :

8.31 Providing and fixing Ist quality ceramic glazed Sqm 1152 1063.45 1225094.4

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

12 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other frames,

wrought framed and fixed in position with hold

fast lugs or with dash fasteners of required dia

& length (hold fast lugs or dash fastener shall

be paid for separately).

9.1.3 Kiln seasoned and chemically treated hollock cum 6 74199.7 445198.2

Providing and fixing 25 mm thick shutters for

cup board etc. :

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard wood

and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers

on both faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Sqm 240 3086.1 740664

Steel butt hinges with necessary screws

9.20.3 25 mm thick (for cupboard) including ISI Sqm 240 2512.35 602964

15 marked nickel plated bright finished M.S. Piano

hinges IS : 3818 marked with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

9.48.2 Fixed to openings /wooden frames with rawl Kg 1200 197.7 237240

plugs screws etc.

9.53 Providing 40x5 mm flat iron hold fast 400 mm Each 864 194.35 167918.4

long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and

17 embedding in cement concrete block

300x100x150 mm 1:3:6 mix (1 cement : 3

coarse sand : 6 graded stone aggregate 20mm

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete : (copper oxidized as per IS: 1378)

Providing and fixing ISI marked oxidised M.S.

tower bolt black finish, (Barrel type) with

necessary screws etc. complete : (copper

oxized as per IS: 1378)

Providing and fixing ISI marked oxidised M.S.

handles conforming to IS:4992 with necessary

screws etc. complete : (copper oxized as per IS:

9.70S STAINLESS STEEL FITTINGS

Providing and fixing IS : 12817 marked stainless

9.70 steel butt hinges with stainless steel screws etc.

ANODISED ALUMINIUM FITTINGS (ALL FITTINGS

SHALL BE ISI MARKED)

Providing and fixing aluminium hanging floor

door stopper, ISI marked, anodised (anodic

coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour

and shade, with necessary screws etc.

9.105S GYPSUM BOARD PARTITIONS

9.119 Providing and fixing factory made P.V.C. door Metre 360 408.25 146970

frame of size 50x47 mm with awall thickness of

5 mm, made out of extruded 5mm rigid PVC

foam sheet, mitred at corners and joined with 2

Nos of 150 mm long brackets of 15x15 mm M.S.

square tube, the vertical door frame profiles to

25 be reinforced with 19x19 mm M.S. square tube

of 19 gauge, EPDM rubber gasket weather seal

to be provided through out the frame. The door

frame to be fixed to the wall using M.S. screws

of 65/100 mm size, complete as per

manufacturer's specification and direction of

Engineer- in-Charge.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of 19

mm x 19 mm for styles and 15x15 mm for top

& bottom rails. M.S. frame shall have a coat of

steel primers of approved make and

manufacture. M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size 30

mm thickness, 70 mm width out of which 50

mm shall be flat and 20 mm shall be tapered in

45 degree angle on both side forming styles

and 5 mm thick, 95 mm wide PVC sheet out of

which 75mm shall be flat and 20 mm shall be

tapered in 45 degree on the inner side to form

top and bottom rail and 115 mm wide PVC

9.120 sheet out of which 75 mm shall be flat and 20

mm shall be tapered on both sides to form lock

rail. Top, bottom and lock rails shall be

provided both side of the panel. 10 mm (5 mm

x 2 ) thick, 20 mm wide cross PVC sheet be

provided as gap insert for top rail & bottom rail,

paneling of 5 mm thick both side PVC sheet to

be fitted in the M.S. frame welded/ sealed to the

styles & rails with 7 mm (5 mm+2 mm) thick x

15 mm wide PVC sheet beading on inner side,

and joined together with solvent cement

adhesive. An additional 5 mm thick PVC strip of

20 mm width is to be stuck on the interior side

of the 'C' Channel using PVC solvent adhesive

etc. complete as per direction of Engineer-in-

charge, manufacturer's specification & drawing.

Providing and fixing wire gauge shutters using

stainless steel grade 304 wire gauge with wire

9.134 of dia 0.5 mm and average width of aperture

1.4 mm in both directions for doors, windows

and clerestory windows with necessary screws :

Providing and fixing fly proof stainless steel

grade 304 wire gauge, to windows and

clerestory windows using wire gauge with

average width of aperture 1.4 mm in both

directions with wire of dia. 0.50 mm all

11.0 FLOORING

Providing and fixing 10 mm thick acid and/or

alkali resistant tiles of approved make and

colour using acid and/or alkali resisting mortar

bedding, and joints filled with acid and/or alkali

resisting cement as per IS : 4457, complete as

per the direction of Engineer-in- Charge.

In flooring on a bed of 10 mm thick mortar 1:4

(1 acid proof cement : 4 coarse sand)

12.0 ROOFING

Providing, fixing and embedding sand cast iron

accessories for rain water pipes in the masonry

12.40 surrounded with 12 mm thick cement mortar of

the same mix, as that of masonry (lead

caulking will be paid for separately):

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

12.41 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing on wall face unplasticised -

PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.42.5 Bend 87.5 degrees

Providing and fixing tiled false ceiling of

specified materials of size 595x595 mm in true

horizontal level, suspended on inter locking

metal grid of hot dipped galvanized steel

sections ( galvanized @ 120 grams/ sqm, both

side inclusive) consisting of main "T" runner

with suitably spaced joints to get required

length and of size 24x38 mm made from 0.30

mm thick (minimum) sheet, spaced at 1200

mm center to center and cross "T" of size 24x25

mm made of 0.30 mm thick (minimum) sheet,

1200 mm long spaced between main "T" at 600

mm center to center to form a grid of 1200x600

mm and secondary cross "T" of length 600 mm

and size 24x25 mm made of 0.30 mm thick

(minimum) sheet to be interlocked at middle of

the 1200x600 mm panel to form grids of

600x600 mm and wall angle of size 24x24x0.3

mm and laying false ceiling tiles of approved

texture in the grid including, required

cutting/making, opening for services like

diffusers, grills, light fittings, fixtures, smoke

detectors etc. Main "T" runners to be

suspended from ceiling using GI slotted cleats

of size 27 x 37 x 25 x1.6 mm fixed to ceiling

with 12.5 mm dia and 50 mm long dash

fasteners, 4 mm GI adjustable rods with

galvanised butterfly level clips of size 85 x 30 x

0.8 mm spaced at 1200 mm center to center

along main T, bottom exposed width of 24 mm

of all T-sections shall be pre-painted with

polyester paint, all complete for all heights as

per specifications, drawings and as directed by

Engineer-in-charge.

12.52.3 12.5 mm thick square edge PVC Laminated Sqm 1152 1948.95 2245190.4

Gypsum Tile of size 595x595 mm, made of

Gypsum plasterboard, manufactured from

natural gypsum as per IS 2095 part I and

laminated with white 0.16mm thick fire

retardant PVC film on the face side and

12micron metalized polyester on the back side

with all edges sealed with the face side PVC film

which goes around and wraps the edges and is

bonded to the edges and the back side

metalized polyester film so as to make the tile a

completely sealed unit.

13.0 FINISHING

13.4S CEMENT PLASTER (IN COARSE SAND)

13.4 12 mm cement plaster of mix :

13.16S 6MM CEMENT PLASTER

13.16 6 mm cement plaster of mix :

13.25 Extra for plastering:

13.26 Providing and applying plaster of paris putty of Sqm 1152 214.3 246873.6

35 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Distempering with oil bound washable

13.41 distemper of approved brand and manufacture

to give an even shade :

13.41.1 New work (two or more coats) over and Sqm 1152 162.55 187257.6

36 including water thinnable priming coat with

13.44S EXTERIOR FINISHING

Finishing walls with water proofing cement paint

of required shade :

13.44.1 New work (Two or more coats applied @ 3.84 Sqm 1440 97.6 140544

Finishing with Deluxe Multi surface paint system

13.48 for interiors and exteriors using Primer as per

manufacturers specifications :

13.48.1 Two or more coats applied on walls @ 1.25 Sqm 960 158.95 152592

38 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

Painting with synthetic enamel paint of

13.62 approved brand and manufacture of required

colour to give an even shade :

13.62.1 Two or more coats on new work over an under Sqm 1152 191.4 220492.8

39 coat of suitable shade with ordinary paint of

approved brand and manufacture

15.0 DISMANTLING AND DEMOLISHING

Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per direction

of Engineer - in - charge.

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c cum 120 1239.6 148752

equivalent design mix)

Demolishing brick work manually/ by

mechanical means including stacking of

15.7 serviceable material and disposal of

unserviceable material within 50 metres lead as

per direction of Engineer-in-charge.

17.0 SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan of Each 24 5781.35 138752.4

size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china

pedestal type water closet (European type W.C.

pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever),

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic Each 24 5540.55 132973.2

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32 mm

17.7 C.P. brass waste of standard pattern, including

painting of fittings and brackets, cutting and

making good the walls wherever require:

17.7.7 White Vitreous China Flat back wash basin size Each 24 1318.35 31640.4

44 450x 300 mm with single 15mm C.P. brass

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

17.31 Providing and fixing 600x450 mm beveled edge Each 24 1411.15 33867.6

mirror of superior glass (of approved quality)

45 complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws

and washers complete.

Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.2 600 mm long towel rail with total length of 645 Each 24 600.35 14408.4

46 mm, width 78 mm and effective height of 88

mm, weighing not less than 190 gms.

18.0 WATER SUPPLY

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all floor Litre 12000 9.7 116400

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank.

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass bib cock of

approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long body bib

18.51 cock of approved quality conforming to IS

standards and weighing not less than 690 gms.

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of approved

quality and colour.

18.54.1 15mm nominal bore, 86 mm long, weighing not Each 48 109.85 5272.8

less than 88 gms

18.59S AIR VALVE & WATER METER (BULK TYPE)

18.65 Providing and fixing PTMT soap Dish Holder Each 48 96.75 4644

having length of 138mm, breadth 102mm,

height of 75mm with concealed fitting

arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C.

18.74 connection pipe with PTMT Nuts, collar and

bush of approved quality and colour.

21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with

extruded built up standard tubular sections/

appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps

at junctions, i.e. at top, bottom and sides with

21.1 required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically

wherever required including cleat angle,

Aluminium snap beading for glazing / paneling,

C.P. brass / stainless steel screws, all complete

as per architectural drawings and the directions

of Engineer-in-charge. (Glazing, paneling and

dash fasteners to be paid for separately) :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings and

the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic

21.3.1 With float glass panes of 4.0 mm thickness Sqm 288 1019.8 293702.4

(weight not less than 10kg/sqm)

Schedule Schedule A 3-Items of steel reinforcement under DSR-2021.

Item- 01 Items of steel reinforcement under DSR-2021.

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCED CEMENT CONCRETE

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above plinth

5.22A.6 Thermo-Mechanically Treated bars of grade Fe- Kg 4800 89.65 430320