Remodeling the open terrace at IMHANS to an Auditorium ,Kozhikode (DSR 2018)(Re)

Amount

CIVIL WORKS

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.17.2 : Dismantling steel work in single sections including dismembering and stacking within 50 metes lead in:Channels, angles, tees and flats

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.99.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.1 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

od342295/2023_2024 : Providing and fixing 8 mm Toughened glass in stainless steel bars aluminum frame work. ( Cost of stainless steel bar aluminium will be measured and paid separately )

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

11.40 : Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.48.2 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

od342192/2023_2024 : Supplying and fixing PVC door (Syntex)for toilets including cost and conveyance of all materials and labour

od342195/2023_2024 : Engaging Man Labour - Coolie

od342196/2023_2024 : Providing and fixing counter Chairs

od342197/2023_2024 : Providing and fixing office Visitors chair

od342198/2023_2024 : Supplying of PVC chair (good quality) with polyester seat cover as required

od367983/2023_2024 : Providing and fixing Executive tables having size 5ftx2.5ft or available nearby size

od342199/2023_2024 : Providing and fixing ready made fabric curtains to the opening including all PVC fittings labour charges etc.

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.57 : Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS : 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge

WATER SUPPLY AND SANITORY WORKS

17.1.1 : Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.2.1 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.7.4 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brass pillar taps

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.50.1 : Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

50.17.1.3 : Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.4 : Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

50.18.8.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

50.18.8.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.14.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

50.18.9.15.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10Kgf/cm2- External work- Exposed on wall

50.18.9.16.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.8 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

od342416/2023_2024 : Constructing inspection chambers of size 90 X 90cm inside the sewer lines upto a depth not exceeding 60cm with brick in cement mortar 1:6, 23cm (one brick) country burnt thick thick walls, forming channels inside with cement concrete 1:4:8 using 40mm broken stones, plastering the inside and channels with CM 1:3, 12mm thick with neat cement flushing coat including RCC cover slab 75 mm thick including all earthwork and foundation concrete 10cm thick.

od342417/2023_2024 : Constructing inspection chambers of size 40 X 40cm inside the sewer lines upto a depth not exceeding 60cm with solid blocks in cement mortar 1:6, 20cm thick walls, forming channels inside with cement concrete 1:4:8 using 40mm broken stones, plastering the inside and channels with CM 1:3, 12mm thick with neat cement flushing coat including RCC cover slab 50 mm thick including all earthwork and foundation concrete 5cm thick.

ELECTRICAL WORKS

1.10.1 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.10.2 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.9 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.14.10 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.35 : Erection of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.

1.44 : Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

1.50.1 : Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

1.55.1 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

1.55.2 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.56 : Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.20 : Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

5.6 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

6.2 : Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

6.4 : Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

6.7 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

6.8 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

6.12 : Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

90.4.1 : Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

90.4.5.2 : Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.

90.10.3.15 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )

90.10.3.33 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )

90.14.10.2 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.

90.14.10.4 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.

90.11.1.20 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

90.12.7.40 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.

90.12.7.41 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.

90.12.7.42 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

90.16.5.3 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.

od366379/2023_2024 : S/F 4 way Metal Enclosure : Supply and fixing 4 way metal enclosure on surface / recess complete with earth bar and din bar detached gland plate, interconnection, phosphatized and powder painted including earthing etc, as required..(But without MCB/RCCB/ Isolator)

od362032/2023_2024 : S/F 'C' Series TP MCB : Supplying and fixing 40A to 63 A rating Triple pole , 415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCCB DB/ MCB DB complete with connections, testing and commissioning etc. as required.

od366120/2023_2024 : Supply of 20W LED batten/ tube light fittings : Supply of 20W Surface mounting type LED lenier batten/ tube light fittings with output of 2000 lumen, made out of CRCA body with white acrylic cover etc. as required.

od366141/2023_2024 : Supply of 18 W recess LED down lighter : Supply of round/square shaped 18 W low glare, recess mounting type, integral LED down light fittings with white powder coated Die cast aluminium body with anodised aluminium reflector etc.as required.

od366121/2023_2024 : Supply of 12 W recess LED down lighter : Supply of round/square shaped 12 W low glare, recess mounting type, integral LED down light fittings with white powder coated Die cast aluminium body with anodised aluminium reflector etc.as required.

od366122/2023_2024 : Supply of 10 W LED bulkhead luminaire : Supply of 10 W, low glare LED bulkhead luminaire with Die cast aluminium Frame, anodized aluminium reflector etc.as required.

od366123/2023_2024 : Supply of 5W LED mirror light fittings : Supply of 5W Surface mounting type LED mirror lenier batten/ tube light fittings, made out of CRCA body with white acrylic cover etc. as required.

od362042/2023_2024 : Supply and fixing LED strip light IP20 5W,(60LED/MTR) 6500K 5Mtr/roll with IP20 DRIVER PSLM01257 makebajaj/philips/ panasonic/luker/equivalant govt approved including connections as required.

od366210/2023_2024 : Supply of 2 W Angular Up warm wall light fitting : Supply of 2 W Angular Up warm wall light fitting with metal body and all accessories as required

od366211/2023_2024 : Supply of 4 W Up and Down warm wall light fitting : Supply of 4 W Up and Down warm wall light fitting with metal body and all accessories as required.

od366212/2023_2024 : SITC of LED Profile Strip light : Supply, installation, testing and commissioning of LED Profile Strip light with Profile Channel, Driver Unit and all other accessories including connection and labour charge etc.as the direction of Engineer in charge as required.

od362043/2023_2024 : Supply and Fixing Recess type ceiling light 3 W LED spot light fitting make Luker/Bajaj/Crompton/Philips or equivalant govt approved brand including connection etc as complete

od366142/2023_2024 : Supply of 1200mm Ceiling Fan : Supply of 1200 mm sweep electric Ceiling Fan, white colour, capacitor type with double ball bearing, shackles, 300 mm down rod, canopies, blades and resistance type regulator etc. suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required.

od366143/2023_2024 : Supply and fixing of 400mm Wall Fan : Supply and fixing of 400 mm sweep wall fan with three positions and pulling cords and giving connection etc. as required

od366144/2023_2024 : Supply of 225mm Exhaust Fan : Supply of 225 mm sweep light duty exhaust fan suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required.

od366145/2023_2024 : Supply of 305 mm Exhaust Fan : Supply of 305 mm sweep heavy duty exhaust fan in metal frame suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required.

AIR CONDITIONING WORKS

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od366767/2023_2024 : Inverter Ductable Air Conditioners : Supply, Installation, Testing and commissioning of Air-Cooled Concealed Non Inverter air conditioner with following nominal capacity fitted with rotary/scroll compressor & micro-controller panel with all other standard accessories. 11TR Ductable Unit

od366768/2023_2024 : Inverter Ductable Air Conditioners : Supply, Installation, Testing and commissioning of Air-Cooled Concealed Non Inverter air conditioner with following nominal capacity fitted with rotary/scroll compressor & micro-controller panel with all other standard accessories. 8.5TR Ductable Unit

od366769/2023_2024 : Inverter Ductable Air Conditioners : Supply, Installation, Testing and commissioning of Air-Cooled Concealed Non Inverter air conditioner with following nominal capacity fitted with rotary/scroll compressor & micro-controller panel with all other standard accessories. 5.5TR Ductable Unit

od366784/2023_2024 : SITC of Split Air-conditioner with stabilizer :Supplying, installation testing & commissioning of 5 star rated 1TR split Air conditioner with supports, suitable for single phase, 50 Hz, 230 Volts , A/C supply with hermitically sealed compressor with air cooled condenser, motor capacitor start run, capacitor relay and overload protector interconnections including all accessories and remote with special purpose A/C stabilizers, filling of gas etc as required

od366770/2023_2024 : Refrigerant Piping : Supply, Installation, Testing and Commissioning of Insulated refrigerant piping out of refrigerant grade hard drawn copper pipes duly insulated with 13 mm nitrile rubber pipe sleeves the insulation manufacturer recommendations. For 11 TR (Make : MANDEV/MEXFLOW)

od366771/2023_2024 : Refrigerant Piping : Supply, Installation, Testing and Commissioning of Insulated refrigerant piping out of refrigerant grade hard drawn copper pipes duly insulated with 13 mm nitrile rubber pipe sleeves the insulation manufacturer recommendations. For 8.5 TR (Make : MANDEV/MEXFLOW)

od366772/2023_2024 : Refrigerant Piping : Supply, Installation, Testing and Commissioning of Insulated refrigerant piping out of refrigerant grade hard drawn copper pipes duly insulated with 13 mm nitrile rubber pipe sleeves the insulation manufacturer recommendations. For 5.5 TR (Make : MANDEV/MEXFLOW)

od366773/2023_2024 : Refrigerant Piping : Supply, Installation, Testing and Commissioning of Insulated refrigerant piping out of refrigerant grade hard drawn copper pipes duly insulated with 13 mm nitrile rubber pipe sleeves the insulation manufacturer recommendations. For 1 TR (Make : MANDEV/MEXFLOW)

od366774/2023_2024 : AC Sheet Metal Work : Supply, Installation, Testing & Balancing of Air Distribution system consist of Site fabricated rectangular duct Galvanized GI sheet metal ducting complete with all fittings and supports. GSS DUCTING (24 Gauge) (Make: TATA/JINDAL/SAIL)

od366775/2023_2024 : AC Sheet Metal Work : Supply, Installation, Testing & Balancing of Air Distribution system consist of Site fabricated rectangular duct Galvanized GI sheet metal ducting complete with all fittings and supports. GSS DUCTING (22 Gauge) (Make: TATA/JINDAL/SAIL)

od366776/2023_2024 : Acoustic Insulation : Supply, Installation, Testing and Commissioning of Acoustic insulation of ducting using 10 mm thick open cell Nitrile Rubber insulation with recommended adhesives and tape. 10 mm thick

od366777/2023_2024 : Thermal Insulation : Supply, Installation, Testing & Commissioning of ducts using nitrile rubber of following thickness with recommend Adhesives and sealed with black adhesive tape. 13 mm thick

od366778/2023_2024 : Supply, fabrication, installation, testing of flexible connections made out of fire resistant flexible double canvas sleeve as required.

od366779/2023_2024 : Grill & Diffuser : Supply and fixing of Powder coated extruded Aluminium Supply and Return air Grilles with horizontal fixed bars and end flanges as required

od366780/2023_2024 : SITC of Volume Control Damper : Supply, Installation, Testing & Commissioning of Volume Control Damper as required

od366781/2023_2024 : Drain piping : Supply, installation, testing and commissioning Rigid PVC drain piping exposed with 9 mm Nitrile rubber insulation as required.

od366782/2023_2024 : Refrigerant gas (R 410a) : Supply, filling, testing and commissioning of Refrigerant gas (R 410a) as required

CCTV WORKS

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.53.1 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

od366566/2023_2024 : Supply, installation, testing and commissioning of CP Plus 8 port POE Giga switch as required

od366292/2023_2024 : Supply and fixing 2 TB hard disk WD survellience .

od366580/2023_2024 : Supply and fixing of CCTV Camera Box of approved make as required

od366581/2023_2024 : Supply, installation, testing and commissioning of 8 channel up to 4 MP 1 SATA NVR of HIKVISION/ equivalent Govt. approved make as required

od366582/2023_2024 : Supply and providing 2U cabinet of approved make powder coated with glass panel front door including giving connection etc complete as required.

od366583/2023_2024 : Supply and providing 4U cabinet of approved make powder coated with glass panel front door including giving connection etc complete as required.

od366293/2023_2024 : Supply and fixing 2MP Bullet IPcam 4mm lens True day/night DNR, smart IR upto 30 m IR distance IP66 weather proof 265+ compression HIKVISION/ equivalent reputed brand including connection etc as required.

od366296/2023_2024 : Supply,marking,crimping RJ45 connectors /sockets and fixing to the existing enclosure and giving connection etc complete

od366569/2023_2024 : Supplying and fixing 32 inch LED Television including all cost of labour and conveyance charges etc.

FIRE FIGHTING WORKS

od366428/2023_2024 : Above Ground Piping (MS B CLASS) : Supply, Installation, Testing & Commissioning of M.S 'B' (Medium class) pipes confirming to IS 1239, IS3589 including cutting, welding complete with fittings like elbow, bends, flanges, reducers, M.S nuts, bolts and washers etc. The pipes shall be painted with one coat of primer & two coats of synthetic enamel Paint using approved shade, hanging supports with standard spacing, suitable supports, fasteners, threaded rods etc., fixing in/on walls/ ceiling as per standards. 80 mm dia

od366429/2023_2024 : Above Ground Piping (MS B CLASS) : Supply, Installation, Testing & Commissioning of M.S 'B' (Medium class) pipes confirming to IS 1239, IS3589 including cutting, welding complete with fittings like elbow, bends, flanges, reducers, M.S nuts, bolts and washers etc. The pipes shall be painted with one coat of primer & two coats of synthetic enamel Paint using approved shade, hanging supports with standard spacing, suitable supports, fasteners, threaded rods etc., fixing in/on walls/ ceiling as per standards. 25 mm dia

od366430/2023_2024 : Branch Pipe : Supply of GUNMETAL 63mm Short branch pipe with 2.3kg weight nozzle as per IS: 903, ISI Marked.

od366431/2023_2024 : RRL Hose : Supply, installation and testing of non-percolating, rubber reinforced lined fire hose pipe ISI marked (IS:636) 63 mm dia x 15 m long complete with instantaneous type GUNMETAL. 63 mm dia, ISI marked Male & Female couplings (IS:903) bound and riveted to hose pipe including all accessories as required for complete installation. ( C.P Hose Not Allowed)

od366432/2023_2024 : Hose Reel Drum : Supply, installation, testing and commissioning of compact type first aid fire hose reel with wall mounting swinging-type drum complying with ISI marked, 19 MM x 30 M long Nylon braided thermoplastic hose with shutoff nozzle, installation brackets, complete in all respects including all accessories as required for complete installation.

od366433/2023_2024 : Hose Box : Supply and installation of Weather proof indoor hose cabinets fabricated from M.S. sheet with glass door with locking arrangement, suitable to accommodate .2 No 15 M long hose and 1 No branch pipe. Glass will be transparent. The cabinet shall be painted with coat of Approved red paint from outside and white paint from inside including all accessories as required for complete installation.(size shall be such that the above all items can be accommodated). as per industrial standards

od366434/2023_2024 : Ball Valve : Supply, Installation, Testing and Commissioning of Ball valves (PN 25) with fittings of screwed end type.20 mm dia

od366435/2023_2024 : Hydrant Valve : Supply, installation, testing & commissioning of Single headed, GUNMETAL .304 ISI marked, oblique pattern hydrant landing valve with 80 mm dia flanged inlet and 63 mm dia instantaneous type female outlet complete with PVC cap and Chain.

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od366436/2023_2024 : Supply, Installation, Testing and Commissioning of 16 Zone Fire Alarm Control Panel conventional type, micro processor based control panel, made of MS powder coated CRCA sheet with audio and visual display & supplied with all standard mounting accessories.

od366437/2023_2024 : Manual Call Point : Supply, Installation, Testing and Commissioning of Manual Call Point break glass type powder coated MS box ,24/12 Volt DC operated, and with necessary attachments.

od366438/2023_2024 : Hooter : Supply, Installation, Testing and Commissioning of Audio alarm hooter (sounder) powder coated MS box, 24/12 Volt DC operated with necessary attachments.

od366439/2023_2024 : Smoke detector : Supply, Installation, Testing and Commissioning of CONVENTIONAL SMOKE detectors with all standard accessories like base etc to be installed under or above false ceiling. Smoke detector

od366440/2023_2024 : Fire Alarm Cabling : Supply, Installation, Testing and Commissioning of PVC insulated fire retardant FRLS wire armoured 2Cx1.5 sq.mm with ISI mark.

od366443/2023_2024 : SIGNAGES : Supplying Installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, luminescent self adhesive vinyl painted foam board, complete with mirror fasteners. FIRE DUCT, EXIT, FIRE EXIT, NO SMOKING

od366494/2023_2024 : Fire Extinguisher : Supply and Installation of ABC type fire extinguisher of 4 Kgs.IS 4308. Capacity with initial filling in brand new cylinder with powder coated finish, discharge hose, wall mounting bracket etc. complete. The Extinguisher is manufactured strictly as per IS: 15683:2018

SOUND SYSTEM AND PROJECTOR WORKS

1.17.2 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od366704/2023_2024 : SITC of Amplifier 500W : Supply, Installation, Testing & Commissioning of SPA 5000EM (500 watt), Frequency Response 20Hz-20,000Hz ±0.5dB Power Amplifier, Protection Devices-Temperature, DC, RFI Short Circuit, Soft-Start, Over load, input power supply AC: 220-240V 50/60Hz,Input Connector (Per CH.)-XLR, 1/4” TRS Jack, output 8 Ω (True RMS), 20Hz-20kHz,1% THD,8 Ω (EIA), 1kHz ,1% THD, including all accessories etc. as per the direction of Engineer in charge as required.

od366679/2023_2024 : SITC of Corded Microphone : Supply, Installation, Testing & Commissioning of Dynamic Wired SM 650XLR Microphone - Corded Microphone with quick detachable holder with 3- pin professional XLR connector & 6 mtrs. twin core shielded low noise cable, Frequency Response- 50-15,000Hz ,Impedance-600Ω,Sensitivity- .5mV/Pa, including all accessories etc. as per the direction of engineer in charge as required.

od366680/2023_2024 : Supply and fixing of XLR male and female connectors and giving connection as required

od366681/2023_2024 : SITC of 90 Watt Wall Mounting Audio Speaker : Supply, Installation, Testing & Commissioning of ARC 90 .90 watt wall Mounting Audio Speaker, frequency response 50-20,000Hz ,Impedance 8Ω, LF suitable Driver Size-woofer with voice coil, HF suitable Driver Size-exit with voice coil, Input Connector 2 x Speakon, suitable size, including required size speakon to speakon cables wire speaker audio amplifier cord with all accessories etc. as per the direction of engineer in charge as required.

od366682/2023_2024 : SITC of 400W Compact Active Subwoofer: Supply, Installation, Testing & Commissioning of SUB 12. 400 Watt Compact Active Subwoofer ,Max. Rated SPL 133dB, frequency response 40-120Hz , Impedance 8Ω ,LF Driver suitable Size Woofer, Voice Coil, Input Connector 2 x neutrik combo, Output Connector 2x XLR Parallel, 2x XLR X-Over, with suitable size, including required size speak on to speak on cables wire speaker audio amplifier cord with all accessories etc. as per the direction of engineer in charge as required.

od366683/2023_2024 : SITC of Audio Mixer: Supply, Installation, Testing & Commissioning of Orb 822SC-1 - 8 channel live Audio Mixer with One Knob Compression and recording option, connecting cables, including all accessories etc. as per the direction of engineer in charge as required

od366694/2023_2024 : SITC of Projector : Supply, installation, testing and commissioning of MS550 SVGA DLP Projector, with High Brightness 3600 ANSI Lumens, 20000:1 High Contrast Ratio, Dual HDMI, VGA, Keystone Correction, Up to 15000 Hrs Extra Long Lamp Life, Anti-Dust Sensor, 3D Capable", Power Supply AC 100 to 240 V, 50/60 Hz, VGA/HDMI Cable, Power Cable, , Remote Control Included Batteries, User Manual (CD) ,including all accessories and giving connection etc. as per the direction of Engineer in charge as required

od366695/2023_2024 : Supply and fixing of Projector stand : Supply and fixing of Universal CK-3ft Ceiling kit Projector stand of approved make as required

od366696/2023_2024 : Supply and laying of HDMI cable : Supply and laying of HDMI cable of Govt. approved brand and giving connection as the direction of Engineer in charge as required

od366705/2023_2024 : Supply and laying of Microphone cable : Supply and laying of Microphone cable with 2 conductors of 0.5 mm standard bare copper, polyethylene insulated, overall braid shielded, PVC jacketed from system communication with mic and mixer of approved make and specification and giving connection etc. as required.

od367889/2023_2024 : supply and fixing of podium stand including provision for mic

Bidder Name

AJITH KUMAR P