SPECIAL REPAIR WORK OF BLDG NO P 23, P 29 AND P 40 AT CERTAIN MIL UNIT, PROVN OF COVERED PARKING SHED FOR PARKING AT CERTAIN MIL UNIT AND SPECIAL REPAIR SEWAGE LINE BLOCK NO 4/R/7 AND 4/R/8 AT SUJITH VIHAR SOUTH ZONE AT BINNAGURI UNDER GE (S) BINNAGU

Amount

Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and removal of taken down meterials off the site

M&L for pre-painted galvalume aluminium zinc coating GI based Corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering fixed with self tapping screws/J hooks as specified.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering fixed with self tapping screws/J hooks as specified.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets and removal of taken down meterials off the site

Supply and fixing as in repairs for aluminium anodised snap grid (605X605mm size) to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm, cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including proper hanging arrangement with 4 mm dia anodized galvanised iron wire with false ceiling iof 4 mm thick E board classic for insulation and accoustic purposes of size 600X600 mm fixed with necessary accessories to frame work or with staples on snap grid upto ceiling proper scafolding arrangementsand with complete all as specified.

-----Blank-----

Dismantling of timber scantling 40 sq.cm and over in section in any position

M&L for mild steel rolled sections conforming to Fe - 410 (Gde E-250) as in main and cross beams, hip and jack rafters; verticals , purlins where connected to common rafter and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates.

Taking down cement plaster any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc.

M&L for rendering 20mm thick in cement mortar 1:4 in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & fair (WPC for finishing layer will be paid seperately as supply only).

Supply only integral water proofing compound.

M&L for two coat of acrylic distember on new wall surface including preperation of the surface all as specified.

M&L applying two coats of exterior acrylic emulsion paint of standard quality and make ,over a coat of white primer including preparation of new /old wall surfaces complete all as specified

Complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc and applying two coats of acrylic distemper over a coat of primer complete all as specified

M & L for complete removal of existing treatment and finishing the walls with two coats Acrylic smooth exterior emulsion paint of required shade for New work over and including priming one coat of exterior primer applied all as per manufacturer's specification and as specified.

Demolition of brick work built in cement mortar of any description and removal of taken down meterials off the site

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1;6 complete all as specified

Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) and removal from site.

All as per item No 18 here-in before but n.exc 1.5 Sqm each.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125mm x 60 mm x 1.25mm (thick) complete all as specified

M&L for plain, framed, factory made panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats.

S&F second class hardwood, factory made glazed and skelton shutters 35 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) supplied and fitted to chowkats.

S&F in repair of factory made steel windows with side hung shutters openable type including friction/projected type hinges steel handle and peg stay complete without glazing bars fixed to existiog opening and making to match as per existing surfaces.

S&F in repair of factory made steel windows with side hung shutters openable type including friction/box type hinges steel handle and peg stay complete with glazing bars fixed to existiog opening and making good to match as per existing surfaces including taking out old/unserviceable steel windows.

S&F in repair factory made steel ventilator with top hung shutter including friction/ box type hinges ,steel peg stay complete including taking out old/unserviceable steel ventilator and making good to match as per existing surfaces etc complete all as specified

M&L for two coats of synthetic enamel painting to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth.

M&L for 40 mm thick cement concrete type B1, 1:2:4 (20mm graded aggregate) as in flooring of floor etc and finished complete all as specified

M & L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’

M&L for 75mm thick PCC type C-2 (1:3:6) using 40 mm graded agg in plinth protection path/hardstanding finished cement concrete surfaces fair and even all as specified

Demolition of stone slab of any description or thickness as in floors, apron etc laid, bedded and pointed in any mortar complete all as specified

M&L for laying machine cut kota stone slab flooring 20-25mm thick over cement screed base of 15mm thick (average thickness) in cement motar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified

M&L for laying machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick (average thickness) in cement motar 1:4 laid and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete all as specified

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in surface channels/drain including forming fair finished to drain channel.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified

M & L 60 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified

-M & L for PCC 1:2:4 type B-I ,(using 20 mm graded stone aggregate) as. in coping /benching to sides of foot path fininished fair and even including necessary formwork etc complete all as specified D44

M&L for RCC Type (1:1.5:3) (Nominal mix) (20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L RCC Type A1 (1:1.5:3) (Nominal mix) (20 mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified.

Use and waste of formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Use and waste of form work square, rectangular or ploygonal fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

Ditto, as above item no 41 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified

M&L for Fly ash brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified

Sand filling under floors or in foundations including watering and consolidation

M &L for Stone Hardcore of gauge n exc. 63 mm, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface complete all as specified

M&L for 100 mm thick cement concrete type C2 (1:3:6 ) (40 mm graded aggregate) as in subbase of floor etc and finished the complete all as specified

M&L 80 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified

S&F steel work in Trusses, purlins, posts and the like using tubular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming I.S.1161-2014/IS 4923-1977 grade St-240 complete all as specified

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering fixed with self drilling screws with EPDM washer etc complete all as specified.

Ditto--- all as per item No 49.00 above but as in eaves board fixed with selp tapping screw as specified.

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150 mm all as specified

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 100 mm

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 200 mm

Demolition of cement concrete (Unreinforced) Concrete of any description and in any position not otherwise specifically provided for

Taking down cement plaster any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc.

Excavation in trenches n.exc 1.5 in deep and n.exc 1.5 m wide for foundation etc not exc 10 sqm on plan and getting out in soft / loose soil all as specified

ditto all as per item No 56 above but beyond 1.5m or part thereof in depth beyond the first 1.50mm all as specified

Excavating over areas, exc 1.5 m deep and getting out trenches n.exc 1.5 in deep getting out in soft / loose soil all as specified

ditto all as per item No 58 above but beyond 1.5m or part thereof in depth beyond the first 1.50mm all as specified

Returning filling in, incl spreading, levelling watering & well ramming in layers n.exc 25cm in soft/loose soil all as specified

Removing excavated material (soil) n.exc 1.5 km & depositing where directed all as specified

Demolition of precast concrete block/brick walling built in cement mortar of any description etc complete all as specified.

Demolition of reinforced cement concrete of any description and in any position such as precast manhole cover or cover slabs of septic tank etc (reinforcement cut as required to facilitate demolition)

M&L for precast RCC 1: 1.5 :3 type A-1 using 20mm graded aggregate set in cement mortar 1:4 as in manhole covers including necessary formwork complete all as specified

Supply and fixing150 mm dia (Internal) of salt glazed stone ware drain pipes, grade ‘A’ placed in position sewer pipe lines complete all as specified

Supply and fixing of salt glazed stone ware drain pipes, grade ‘A’ placed in position in old sewer line , 100 mm dia (Internal) of sewer pipe lines complete all as specified

Supply and fixing 200 mm dia (Internal) of salt glazed stone ware drain pipes, grade ‘A’ placed in position sewer pipe lines complete all as specified

Supply and fixing of Bends and taper bends,of 100 mm dia (Internal) of salt glazed stone ware drain pipes complete all as specified

Supply and fixing of Bends and taper bends,of 150 mm dia (Internal) of salt glazed stone ware drain pipes complete all as specified

Supply and fixing of Bends and taper bends,of 200 mm dia (Internal) of salt glazed stone ware drain pipes complete all as specified

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips

M&L PCC 1:3:6 type C-2 (40mm graded aggregate) as in foundations, filling and mass concrete

M&L PCC 1:3:6 Type C-1 (20mm graded aggregate) as in coping/benching for man holes.

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 200mm

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 100mm

M&L for 75 mm thick PCC type C-2 (1:3:6) using 40 mm graded agg in plinth protection path/hardstanding finished cement concrete surfaces fair and even all as specified

M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4.

M&L for 15 mm thick plastering in cement mortar 1:4 on fair faces of brick or concrete surface finished even & smooth without using extra cement.

M&L for preparation of newly wall plastered surfaces and applying three coats of white wash on wall as specified as diracted.

Cleaning of blocked man holes upto 60cm depth by removing of sludge from inside and removing to a distance exc 200m but not exc. 500m and burried the same in to earth pits including excavation of earth pits of required size & depth, depositing & spreading of sludge, returning in filling earth over sludge and removal of surplus soil to a distance not exc. 50m all complete as specified

All as per item No 82 above but exc 0.60Metre but nexc.1.50Metre in deep.

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors/gate, ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M & L for preparation of new steel surfaces exc 10cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete.

M&L in reapir for Salt Glazed stone ware gulley trape, sqaure or round mouthed type 150x100mm complete all as specified

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated, IS 694 unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less than 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes duly painted with anticorrosive paint, concealed in walls with bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications all as specified for the following :-

One light point controlled by one way switch 5/6 amps.

One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

One socket out let 5/6 amps point on the same board

One socket out let 5/6 amps point on the independent board

All as per item No 88 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified

S&F switch piano flush type 5/6 amps single pole one way complete all as specified

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified

S&F switch piano flush type 15/16 amps single pole one way complete all as specified

Supply and fix Sheet Metal Enclosure/ industrial socket TP and earth enclosure with a three pin and earth plug with socket complete with of 63 amps capacity with socket and top with MCB 63 amps TP.

S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified

S & F deluxe fan electronic regulator 230 volts AC 50 Hzs rotary step white/ivory finish complete all as specified

S&F LED lights fitting 1x 20W, 220V AC decorative box type with driver,IP 20, class I, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all accessories internally prewired and including necessary taking down the old unserviceable fitting complete all as specified.

S&F LED Bulk Head lights fitting 1x 9/10W, 220V AC integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 100 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-43 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Tripple pole & neutral with din rail, IP-43 protection suitable for fixing MCB"S/lsolators complete includingfour pole MCCB 63 Amps with blanking plates as required and taking down the old one complete all as specified

S&F MCB, Triple pole Neutral 100 amps, 415 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘B’ curve, 10 KA all complete including taking down the old one complete all as specified

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified

M & L Sub main wiring concealed type where not feasible ceiling of beam on surface with saddle with Four run single core cable PVC insulated cable with 4.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4.0 Sqmm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete including necessary taking down.(NOTE :Four run of submain wiring cable alongwith one run of earth wire shall be measured as one length.

M & L Sub main wiring concealed type where not feasible ceiling of beam on surface with saddle with two run single core cable PVC insulated cable with 4.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4.0 Sqmm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete including necessary taking down.(NOTE : Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length. .

Taking down ceiling fan sealing cable end, dismantling blades and removing fan and blades to store complete all as specified

M & L for painting of ceiling fans of any make/model and size complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.complete all as specified

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified

SHRI PRADEEP PARIK (BID ID -3367293)

M/S NIKITA ENGINEERING CO (BID ID -3367461)

Samir Kumar Dey (BID ID -3367466)

M/S MOHAN KUMAR BANSAL (BID ID -3367486)

N K Construction (BID ID -3367407)

M/s. RAMPHAL GARG (BID ID -3367416)

flexpro construction company (BID ID -3367442)