TSM Nilakkal Construction of Waiting hall Cloak rooms Bath rooms and Toilets including internal and external Water Supply Sanitary Installations Bio-digester and Over Head Tank (Re-tender)

Amount

SH-1:Earth Work: Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. a) All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil.

Supplying and filling in plinth with Quiary dust under floors, including watering, ramming, consolidating and dressing complete (LMR)

SH-2:Concrete Work: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand(Zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

SH-3: Masonry work: Solid block using pre cast solid blocks (Factory made) of size 30X20X15cm or nearest available size conforming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 15cm and above in CM 1:6 (1 Cement:6 Coarse sand)etc (LMR)

Solid block using pre cast solid blocks (Factory made) of size 30X20X15cm or nearest available size conforming to IS 2185 part 1 of 1979 for Superstructure upto floor two level with thickness 15cm and above in CM 1:6 (1 Cement:6 Coarse sand)etc (LMR)

SH-4: Reinforced Cement Concrete Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level- 1:1.5:3 (1 cement : 1.5 coarse sand(Zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(Zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for all heights Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for all heights:Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for all heights::Stairs, (excluding landings) except spiral-staircases.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete for all works: Thermo Mechanically Treated bars of grade Fe 500D or more

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).

SH-5: Stone work: Dry stone masonry for Soak pit foundation (LMR)

Random rubble masonry in Cement Mortar 1:6 (1 cement : 6 coarse sand) in foundation and basement.(LMR)

SH-6: Marble and Granite work: Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the Architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite slab Jet black,cherry red,Elite brown,Cat eye or equivalent

SH-7: Wood & PVC work: Providing Wood work in frames of doors windows clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia. and length (hold fast lugs or dash fasteners shall be paid for seperately :second class teak wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Second class teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Second class teak wood

Providing and fixing glazed shutters for doors, window and clerestory windows using 4mm thick float glass panes, including ISI marked M.S pressed butt hinges bright finished of required size with necessary screws: second class teak wood:30mm thick.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge. Extruded section profile size 48x40 mm.

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm) with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10mm

Providing and fixing chromium plated brass casement stays (straight peg type) with necessary screws etc. complete : 200 mm weighing not less than 240 gms

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250x16mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125mm

SH-8: Steel work:Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

SH-9: Flooring:Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturere) with water absorption less than 0.08% and conforming to IS:15622 of approved brand and manufacturer in all colours and shade in skirting,riser of steps laid with cement based high polimer modified quick set tile adhesive (water based) conforming to IS:15477 in average 6mm thickness, including grouting of joints (payment of grouting of joints to be made seperately) size of tile 600x600mm

Providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturere) with water absorption less than 0.08% and conforming to IS:15622 of approved brand and manufacturer in all colours ans shade laid with cement based high polimer modified quick set tile adhesive (water based) conforming to IS:15477 in average 6mm thickness, including grouting of joints (payment of grouting of joints to be made seperately) size of tile 600x600mm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

SH-10: Roofing: Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern.

Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern

18 mm thick plain cement mortar band in cement mortar 1:4(1 cement : 4 fine sand): For Raised band

SH-11: Finishing: 12 mm cement plaster of mix : 1:4(1 cement : 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shadewith ordinary paint of approved brand and manufacture.

SH-12: Water Supply & Sanitary installations:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm nominal bore

Supply & fixing of PVC Health Faucet.(LMR)

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing PVC pipes fitting including fixing the pipe with clamps at 1m spacing.This includes jointing of pipes and fittings with one step PVC cement and testing of joints complete as per direction of Engineer-in-charge -internal work-Exposed on wall.75 mm O.D pipe 6 kg/cm2 (LMR)

Providing and fixing PVC pipes fitting including fixing the pipe with clamps at 1m spacing.This includes jointing of pipes and fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-charge -internal work-Exposed on wall:110 mm O.D pipe 6 kg/cm2 (LMR)

Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement trenching refilling and testing of joints complete as per direction of Engineer-in-charge.75mm dia O.D. pipe 6kg/cm2.(LMR)

Providing and fixing PVC pipes fitting including jointing of pipes with one step PVC solvent cement trenching,refilling andesting of joints complete as per direction of Engineer-in-charge.110mm dia O.D. pipe 6kg/cm2.(LMR)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internal work - Exposed on wall a.20 mm nominal outer dia .Pipes.

b.25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work including cutting chases and making good the wall etc. a.15 mm nominal outer dia .Pipes.

b.50 mm nominal outer dia .Pipes.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank:Circular tank

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PVC floor trap of self cleaning design with PVC screwed down or hinged grating with or without vent arm couple including cost of cutting and making good the wall and floors (LMR)

Construction with solid block 30x20x15 cm for under ground inspection chamber with Cement mortar 1:4(1cement:4 coarse sand) with RCC slab 7cm thick. 45 x45 cm internal dimension with depth of 40 cm including plastering with cement mortar(1Cement:4 fine sand),12mm thick with bed concrete 1:4:8(1 Cement:4 Coarse sand:8 graded aggegate 40mm nominal size) etc.complete

Supply and fixing C.I cover with frame for manhole 450x610mm rectangular C.I cover (light duty) the weight of the cover to be not less than 23Kg and weight of frame to be not less than 15 kg.

SH-13: Miscellanious: Providing architrive work of size 68cmX68cmX22cm, consisting of 3 Nos of size 68X68X4cm bands and @ 1m from the base of R.C.C Column and beam junction with cement concrete 1:1.5:3 (1 cement 1.5 coarse sand zone III 3 sone aggregtae 12.5mm nominal size and finished with cement mortar 1:3 (1 cement 3 fine sand) as per the direction Engineering-incharge

Providing architrive work of size 68X68X31cm, consisting of bands, (2 Nos of size 53X53X4cm,1 No of size 61X61X4 cm and 1 No of size 68X68X4 cm) @ column and beam junction with cement concrete 1:1.5:3 (1 cement 1.5 coarse sand zone III 3 sone aggregtae 12.5mm nominal size and finished with cement mortar 1:3 (1 cement 3 fine sand) as per the direction Engineering-incharge

Shishone Rajan