PROVN OF MT TECH OFFICE INCLUDING DRIVER CHANGE ROOM AND SANITARY ANNEXE IN UNIT AREA AT 810 CETC PURKAZI, PROVN OF TOILET FOR JCOs/OR AT HQ BEG AND CENTRE ROORKEE, MAINT OF OFFICE ACCN OF PAO (ORs) BEG AND CENTRE ROORKEE AND CERTAIN MINOR WORKS UNDE

S&F grating PTMT 100mm dia of best quality including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed.

Excavating in trenches, n.exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, cable etc n exc 10 sq m on plan and getting out in soft soil complete all as specified and directed

M&L Rendering 15 mm thick in CM 1:4 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) including preparation of new plaster surfaces of wall and two coat of cement base paint over a coat alkali resistance primer complete all as specified and directed.

Formwork to sides of rough finished flat surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter complete all as specified and directed

Formwork to sides of rough finished flat surface of concrete sides of pillars, posts, struts, piers, columns and stanchionsr complete all as specified and directed

M&L for Mild Steel work for vertical post, compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, necessary welding etc complete all as specified and directed

Formwork to soffits of flat suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed

M&L for RCC (Nominal mix) Type A1 (1:1.5:3) by using 20 mm graded stone aggregate as in foundatioins including rafts, footings, foundation beams, plinth beam, bases for column etc basement slabs, underreamed piles and mass concrete complete all as specified and directed

M&L for RCC (Nominal mix) Type A1 (1:1.5:3) by using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed

Supplying, laying, jointing and testing LT underground cableof size 16 Sqmm 4 core, heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS, laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/ drains/ culverts duly protected in galvanised steel pipe of suitable size all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends, complete all as specified and directed.

M&L for RCC (Nominal mix) Type A1 (1:1.5:3) by using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for RCC (Nominal mix) Type A1 (1:1.5:3) by using 20 mm graded stone aggregate as in Chajjas and in Shelves andd like complete all as specified and directed

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L brick work Old size sub class B bricks in CM 1:4 straight or curved on plan exc 6m mean radius in half brick walls complete all as specified and directed

M&L Rendering 15mm thick on fair faces of brick work in CM 1:6 or concrete sur faces finished even and smooth without using extra cement complete all as specified and directed

M&L two coats of OBD over a coat of primer including preparation complete all as specified and directed

M&L Rendering 15mm thick on other than fair faces of brick work in CM 1:4 or concrete sur faces fini;shed even and smooth without using extra cement complete all as specified and directed

M&L two coats of cement based paint over a coat of primer including preparation complete all as specified and directed

M&L Rendering 5 mm thick as on ceiling on fair faces of brick work in CM 1:3 or concrete sur faces complete all as specified and directed

M&L three coats of white wash over including preparation complete all as specified and directed

M&L Hardcore of broken stone gauge n exc. 63 mm, deposited, spread and levelled in layers n exc 15cm thick, watered andrammed to a true surface complete all as specified and directed

skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) in skirting area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick CM in 1:4 complete all as specified and directed

M&L joint free Non-

M&L Mild steel TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed

M&L joint free Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in 1:4 complete all as specified and directed

M&L PCC 1:4:8 type D-2 Cement concrete (40 mm aggregate) in foundations, filling and mass concrete surface channel complete all as specified and directed

M&L two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces incl preparation complete all as specified and directed

M&L two coats of synthetic enamel paint over a coat ofpink primer incl preparation on wooden surfaces complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawinge complete all as specified & directed.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

M&L for powder coated aluminium anodised window sliding type (3 shutters type) with sash bars, aluminium sections weighing 0.55 Kg/m(min) including stainless steel wire mesh , necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame, complete all as specified and directed

M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, including S&F 3 to 4 mm thick pin headed glass complete all as specified and directed.

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg sty, 100 mm long tower bolts, complete with glazing bars, dovetailed or welded complete all as specified and directed

Ditto but without glazing bars complete all as specified and directed

S&F factory made steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

S&F concealed 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F 110MM PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length. 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed.

M&L Glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 15mm thick CM in 1:4 complete all as specified and directed

M&L for cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminum paint @ 0.20 kg per Sqm as per manufacturer’s instructions over, complete all as specified & directed.

S&F 25mm stainless steel curtain rod with fancy type bracket and ring complete all as specified and directed.

Removing excavated meterial exc 50 m and n exc 250m depositing where directed at a level n exc 1.5 m above starting point in rocks complete all as specified and directed

Returning filling in including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick for soft/loose rock complete all as specified and directed

M&L for machine cut Kota stone slab 18-20 mm thick, laid over and including 20mm thick screed bed in cement mortar (1:6) using coarse sand as in flooring, set & jointed in neat grey cement slurry and ponted in white cement mixed with pigment to match including grinding and polishing to granite finish complete all as specified and directed.

M&L for machine cut Kota stone slab 18-20 mm thick, laid over and including 10mm thick rendering in cement mortar (1:4) using coarse sand as in vertical surfaces, set & jointed in neat grey cement slurry and ponted in white cement mixed with pigment to match including grinding and polishing to granite finish complete all as specified and directed.

of chullah hoods, chajjas, troughs and similar items in cluding edge complete all as specified and directed

M&L 30mm thick 2nd class HW Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed

M & L for Plain Cement concrete (1:2:4) ty B2 using by using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed

S&F vitreous chinaware coloured wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tied tacks or galvanised wire stapple etc to wooden/steel doors/windows incl wooden beeding/putty complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank 1000 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

M&L for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

M&L for Granite (of any type) work of 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, partion and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed

S&F Brass CP wash hand basin mixer (wall mounted single lever basin mixer complete set) incl copper nipple for connecting with PVC connection 15mm for mixing hot & cold water screwed down for iron pipe and fixed.

M&L PCC type B1 1:2:4 20mm graded aggregate stone aggregate in surface benching/channel/drain/ including necessary form work, finished to required shape all as directed complete all as specified & directed.

M&L Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

M&L PCC 1:4:8 type D-2 (using 40 mm graded aggregate) as in concrete bed to 150 mm bore drain pipe incl packing under hunching against the sides of pipes after pipe laid and tested complete all as specified and directed.

M&L for Precast cement concrete in cover slab for manholes set in CM 1:4, Precast Cement Concrete of type B1 1:2:4 (20 mm graded aggregate) complete all as specified and directed

S&F wash hand basin table top size 425x340x175 mm vitreous china including, waste coupling & PVC waste pipe of 32 mm dia etc complete all as specified and directed.

All as per item No 97 above but 3mm thick pin headed glass complete all as specified and directed

M&L fot Providing precast cement concrete in Type B0 1:2:4 by using 12.5 mm aggregate and set in CM 14 Sqm louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed

M&L for 10 user on site conventional LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below found

M&L 100mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base etc complete all as specified and directed

M&L for PCC type B-1, 1:3:6 using 40mm graded stone aggregate for foundation filling and mass concrete etc complete all as specified and directed

M&L Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick (AZ-150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade ® with Grey cement and pigment complete all as specified and as directed.

S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions.

S&F aluminium alloy, anodised, 300mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Taking down cement or cement lime plaster any description on brick or concrete/stone walls/ceilings including raking out joints, hacking for key, scubbing down with water, etc. complete all as specified and directed

ation, Vent shaft, connection etc, complete all as specified and directed.

Taking down chowkats or frames in repairs with shutter of any description n.exc 1.5sqm each (without taking off shutter from frames) complete all as specified and as directed.

Taking down chowkats or frames in repairs with shutter of any description exc 1.5sqm but not exc 4sqm each(without taking off shutter from frames) complete all as specified and as directed.

M&L MS round bars 10 mm dia as in stiffener for straightening chain link fencing, bent to shape required, including cranking, bending spirally for hooping including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for complete removal of existing treatment on surfaces of walls and applying one coat of wall primer (water thinnable/ solvent thinnable), 2mm wall care putty for making the surface smooth, one coat of wall primer and applying two coats of tractor emulsion oil emulsion distemper to be applied by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for RCC NP3 150 mm diameter Pipes laid on150 mm thick pcc bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. includes all items and activities to execute and make sewer line functional complete all as specified and directed

M&L 18/19 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one faces complete all as specified and as directed by Engr-in-charge.

Cutting holes in brick work built in CM , exc one brick but n exc two bricks for inserting hold fast and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed

M&L Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick (AZ-150) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F flat iron hold fast and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for 2nd class hardwood for plain, solid,straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc. complete all as apecified and directed.

S&F repairs sheet glass frosted 5.5 mm thick,one side frosted, and glazing in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F stainless steel butt hinges, medium weight fixed, 100 mm long complete all as specified and as directed.

M&L for complete removal of existing treatment on external walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 over 1mm thik external wall putty complete all as specified and directed

S&F extruded aluminum alloy handle fabricated type anodized 150mm complete all as specified and as directed.

M&L for Construction of Soakage wells (1.20m Dia and 3.00m in depth) excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size. TD Drg No TD/309/Sheet No 1/4 to 4/4.

S&F floor door stopper overall length of cover plate 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed.

Demolition of concrete in ground floor and pavings not exc 15 cm thickness (below or above GL) for cement concrete un-reinforced complete all as specified and directed

S&F sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

S&F lamp holder (Angular/Straight), insulated body, with back plate complete all as specified & directed.

M&L for preparation of new surfaces of walls by sanding the surfaces and applying one coat of wall primer (water thinable / solvent thinable), 2mm wall putty for making the surface smooth and even one coat of wall primer and applying two coats of tractor emulsion oil emulsion distemper to be applied by approved applicator of the manufacturer of the paint

and all as specified and as approved all as specified and as directed.

One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

M&L for excavation in trenches n.exc 1.5 m width and not exc 1.5 m in depth for fdn etc or for shaft, well, manholes, pier holes etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in hard dense soil.

Ditto all as above but 4 way

S &F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

S&F switch piano flush type white finish 15/16 Amps single pole one way, 230 volts, 50 hz all as specified and directed

S &F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

M&L for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-

M&L for preparation of newly plastered external walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 5489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 over 1mm thick external wall putty complete all as specified and directed

S&F Ceiling fan complete with three blades down rod , accessories 230 V, 1200mm sweep, minimum air delivery of 210 CFM with service value 6.0 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed .

Ditto all as above but of PVC body

S&F galvanised steel water tubing 20mm medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in floor fixed on wall or ceiling complete all as specified and dIrected.

M&L for Sand filling under floorings/pavement cable spread and levelled in layers n.exc 15cm thick complete including watering and consolidation complete all as specified and as directed.

S&F fan regulator, fulsh stepped type, electronic ,450 watt complete all as specified and directed.

M&L for RCC (Nominal mix) Type A1 (1:1.5:3) by using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed

M&L ceiling rose 3 terminal/PVC/polycarbonate, isolated body all as speccified and directed

S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for lamp holder complete all as specified and directed.

S&F galvanised steel water tubing 25mm medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in trench complete all as specified and dIrected.

Supply only 38mm width Glass dividing strips, 3 mm thick and inserted in position confirm to design complete all as specified and directed

S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed.

S&F LED tube light fitting 1 x 20 W, 220 V AC decoratice box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F exhaust fans steel body AC single phase 230 Volt of size 300 mm sweep with blades and frame and louvers complete all as specified and directed.

S&F LED 30 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver,including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed.

S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, P.brass/stainless steel screws, all complete as per architectural drawings and the directions.

M&L for well brunt bricks sub class 'B' in old size as cable protection laid flat width wise complete all as specified and directed.

S&F Single pole and Neutral enclosure with a two pin and earth plug and socket complete with single pole MCB 20 amp complete all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. (earth pit not less than 2.25 mtr depth below ground level at any type of strata) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 15 mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 40 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed.

S&F MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

Cutting of existing steel tubing of size 50 mm for alteration or addition complete all as specified and directed.

Drilling and tapping GI water mains 50mm bore (in position) for branch connections of the internal dia 20mm, complete all as specified and directed.

S&F straight plain brass ferrules (or connecting screws) screwed both ends and fixed to water mains for tapping branch connection of 20 mm bore pipe, complete all as specified and directed.

Screwing eisting steel tubing of size 50 mm for insertion of new 'T'' of size 50 x 20 mm dia for branch connection complete all as specified and directed.

S&F weather proof PVC insulated and PVC sheathed twin core aluminium cable of size 4 sqmm complete all as specified and directed.

S&F sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 4.0 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion complete all as specified and directed

S&F Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F electric water heater, storage type steel body with stainless steel inner tank with glass linning coating and heating element 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hz complete with all accessories such as safety valve, thermostate, NRV, fastners, 15/16 Amp Plug Top, Hot and cold water PVC connection pipe all as specified and directed