PROVISION OF ADDITIONAL STORAGE SPACE FOR SHIPS STORE AT CGDHQ - 15, OKHA UNDER GE (I) CG PORBANDAR

Amount

SCHEDULE 'A' B/R ITEMS

Surface dressing not exceeding 15cm deep in soft/loose soil, complete all as specified and directed by Engineer-in-charge.

Excavating in trenches, not exceeding 1.5 Metre wide and not exceeding 1.5 Metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 Metre in depth and getting out in any type of soil, complete all as specified and directed by Engineer-in-charge.

Material and labour for Plain Cement concrete type C-2, 1 : 3 : 6 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, PCC in foundation, complete all as specified and directed by Engineer-in-charge.

Material and labour for 75mm thick, Plain cement concrete 1:3:6, Type C-2 (using 40mm graded crushed stone agg) as in plinth protection and simillar works finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge. Note: Joints 12mm wide to the full depth of PCC shall be provided at every 3 Metre and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provn shall be deemed to be included in the quoted rate.

Material and labour for Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-charge.

Material and labour for Mild steel CRS TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces, complete all as specified and directed by Engineer-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions of rough finished square or polygonal shape, complete all as specified and directed by Engineer-in-charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams rough finshed concrete surfaces, etc. complete all as specified and directed by Engineer-in-charge.

Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished flat surfaces, complete all as specified and directed by Engineer-in-charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; rough finished flat surfaces not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed by Engineer-in-charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide rough finished, complete all as specified and directed by Engineer-in-charge.

Material and labour for RCC, M-30 (Design Mix) (Using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-charge.

Material and labour for RCC, M-30 (Design Mix) (Using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts, complete all as specified and directed by Engineer-in-charge.

Material and labour for RCC, M-30 (Design Mix) (Using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed by Engineer-in-charge.

Material and labour for RCC, M-30 (Design Mix) (Using 20mm graded stone aggregate) as in Chajjas, complete all as specified and directed by Engineer-in-charge.

Material and labour for RCC, M-30 (Design Mix) (Using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-charge.

Material and labour for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed by Engineer-in-charge.

Material and labour for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured, complete all as specified and directed by Engineer-in-charge.

Material and labour for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed by Engineer-in-charge.

Material and labour for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed by Engineer-in-charge.

Material and labour for 40mm thick PCC type B-0, 1:2:4 (using 12.5mm thick graded stone aggregate) as in Damp proof course to horizontal or vertical surfaces including necessary formwork, complete all as specified and directed by Engineer-in-charge.

Spreading and levelling in layers not exceeding 25cm thick and well ramming including watering as required, complete all as specified and directed by Engineer-in-charge.

Material and labour for Hardcore of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed by Engineer-in-charge.

Material and labour for 75mm thick Cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate), complete all as specified and directed by Engineer-in-charge.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20mm thick screed bedding in Cement Mortar 1 : 4, complete all as specified and directed by Engineer-in-charge.

Material and labour for Machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 10mm thick screed backing coat in Cement Mortar 1 : 4, complete all as specified and directed by Engineer-in-charge.

Material and labour for Precast cement concrete block type C-1, 1:3:6 (using 20mm graded stone aggregate) masonry with solid blocks, exceeding 10cm in width and setting in cement mortar 1 : 6, complete all as specified and directed by Engineer-in-charge.

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in Cement Mortar 1 : 6 and making even and smooth, complete all as specified and directed by Engineer-in-charge.

Material and labour for rendering 5mm thick in Cement Mortar 1 : 4 with water proofing compound over 10mm thick in Cement Mortar 1 : 6 on fair faces of brick work or concrete surfaces and making even and smooth, complete all as specified and directed by Engineer-in-charge. NOTE:- WPC will be measured and paid seperately

Material and labour for rendering 5mm thick on fair faces of brick work or concrete of ceiling surfaces in Cement Mortar 1 : 3 and making even and smooth, complete all as specified and directed by Engineer-in-charge.

Supply only liquid water proofing compound, complete all as specified and directed by Engineer-in-charge.

Supply and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 ±0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories of area not exceeding 2.00 Sqm each, complete all as specified and directed by Engineer-in-charge. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured or payment purpose.)

Material and labour for Second class hardwood plain, solid, straight chowkhat and frame, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joint, complete all as specified and directed by Engineer-in-charge.

Material and labour for Bands, straps, supports or stays for rain water, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed by Engineer-in-charge.

Material and labour for 30mm thick Flush shutters, solid core construction, with particle board core and decorative vaneered face panels on both side, commercial type on both sides covered face veneered decorative type etc., complete all as specified and directed by Engineer-in-charge.

Supply and fixing 125mm long, stainless steel Butt hinges, complete all as specified and directed by Engineer-in-charge.

Supply and fixing 150mm long mat finished aluminium anodised barrel tower bolt and 12 mm dia fixed (ISI maarked), complete all as specified and directed by Engineer-in-charge.

Supply and fixing 150mm long Mat finished aluminium anodised handle cast type and fixed (ISI Marked), complete all as specified and directed by Engineer-in-charge.

Supply and fixing mat finished alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 150mm long (ISI Marked), complete all as specified and directed by Engineer-in-charge.

Material and labour for one coat of synthetic enamel paint over old wooden surfaces of any description not otherwise described over 10cm in width or grith including preparation of surfaces, complete all as specified and directed by Engineer-in-charge.

Material and labour for rendering 15mm thick in Cement Mortar 1 : 4 with water proofing compound on concrete roof surfaces and making even and smooth, complete all as specified and directed by Engineer-in-charge. NOTE:- WPC will be measured and paid seperately)

Material and labour applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2kg/m2 including cleaning surface, complete all as specified and directed by Engineer-in-charge.

Material and labour for APP Based Polymeric memberane minimum weighing 3 kg /sqm and minimum 3mm thick Reinforced with polyster non wove fabric (wt not less than 150 gms/ sqm) laid on primed surface by forced application, complete all as specified and directed by Engr-in- Charge

Material and labour for applying two coats of bituminous aluminium paint on APP membrane of any description laid on roof slabs, complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of new surfaces and applying two coats of oil bound distemper on wall surfaces over a coat of primer, complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of new or old surfaces and applying two coats of oil bound distemper on ceiling surfaces over a coat of primer. complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of new or old plastered/scraped surfaces and applying two or more coats of 100% Premium Acrylic emulusion paint having VOC 50gm/litre and UV resistance as per IS 15489 : 2004, Alkali and Fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with Silicon Aditives @ 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces, complete all as specified and directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed by Engineer-in-charge.

Removing excavated material not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed by Engineer-in-charge.

SCHEDULE 'A' E/M ITEMS

Material and labour for Point wiring complete with 1.5 Sqmm single core PVCinsulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules, complete all as specified and directed by Engineer-in-charge. for following points:- Note: Cost of Making Good of existing disturbed surface deemed to be included in unit rate.

One light point or one fan point controlled by one switch with cables 1.5 Sqmm size

One 3 pin socket outlet 6 amps on the independent, with cables 1.5 Sqmm size

One 3 pin socket outlet 6 amps on the same board with other switches, with cables 1.5 Sqmm size

Supply and fixing modular type 6 A one-way switch, 1 module, complete all as specified and directed by Engineer-in-charge. Make :- Anchor Roma (Urban)/ Legrand (Myrius)/ L&T (EnGem)

Supply & fixing modular socket, 6 Amps, 2/3 pin combind 2 module, complete all as specified and directed by Engineer-in-charge. Make :- Anchor Roma (Urban)/ Legrand (Myrius)/ L&T (EnGem)

Supply & fixing ceiling rose, surface bakelite, 65x17 mm three terminals complete all as specified and directed by Engineer-in-charge. Make :- Anchor Roma (Urban)/ Legrand (Myrius)/ L&T (EnGem)

Supply & fixing surface mounted LED batten fitting 18 Watt , with driver complete all as specified and directed including connecting cable from ceiling rose to terminal block of luminaire complete all as specified and directed by Engineer-in-charge. Make : Philips(BN100C LED40S-6500 PSU L120 GR)/Wipro/ Osram

Supply and fixing MCB (DB) SPN 8 way double door 415 V made of sheet metal enclosure for MCB's as incomming and SPN/SP MCB as outgoing, complete all as specified and directed by Engineer-in-charge. Make: Hager / Legrand/ schneider

Supply & fixing MCB SPN pole 240 volt C curve 10 KA, ISI marked as per IS/IEC 60898-1 2002 of 32 Amps capacity IP 20, complete all as specified and directed by Engineer-in-charge. Make: Hager / Legrand/ schneider

Supply & fixing MCB SPN pole 240 volt C curve 10 KA, ISI marked as per IS/IEC 60898-1 2002 of 40/63 Amps capacity IP 20, complete all as specified and directed by Engineer-in-charge. Make: Hager / Legrand/ schneider

Supply & fixing MCB SP 240 volt C curve 10 KA, ISI marked as per IS/IEC 60898-1 2002 of 6/32 Amps capacity IP 20, complete all as specified and directed by Engineer-in-charge. Make: Hager / Legrand/ schneider

Material and labour for submain wiring 2 X 2.5 Sqmm + 1 X 2.5 Sqmm in existing surface/ Wall using IS:694- 1990 marked 1.1 kV grade single core HR-FR flexible cable having multi- drawn thin strands of electrolytic copper conductors and insulation for phase & neutral and earth continuity conductor connecting to earth dolly, drawn in medium grade non-metallic PVC conduit not less than 25 mm dia., colour-coded and making good of disturbed surfaces of wall/ceiling/floor, complete all as specified and directed by Engineer-in-charge. NOTE: 02 runs of phase & neutral conductors, 01 run of earth continuity conductor and 01 run of concealed conduit shall be measured as one length.

Supply and Fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified and directed by Engineer-in-charge. Make: Almonard/Havells/khaitan

Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with BEE Five star rated with brushless direct current motor (BLDC), complete all as specified and directed by Engineer-in-charge. Make: Almonard/Havells/khaitan

Supply, laying, Jointing and testing XLPE insulated 10 Sqmm 2.0 core cable, Extruded PVC outer sheath and inner sheath, galvanised steel armoured cable with aluminium conductor suitable for rated voltage of 1100 Volts grade and laid in trenches/pipe / ducts or on pole, complete all as specified and directed by Engineer-in-charge.

Supply and laying double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to ISI 14930 ( Part I and II) for protection of underground cables of size 50mm Inner dia with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc. for cable protection complete all as specified and directed by Engineer-in-charge. (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Shree Ashapura Construction Co

RAJ ENTERPRISE

roxy enterprise

JAMNAGAR ELECTRIC AND MACHINERY CO

JAY BHARAT METAL SUPPLIERS

shree chamunda enterprise

K B N TRADERS