Upgradation of Government ITI Kannur

Amount

MAIN BUILDING CIVIL WORKS

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.4 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

6.47 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor Vlevel with RCC band at sill level and lintel level with approved block laying polymermodified adhesive mortar all complete as per direction of Engineer-in-Charge. (Thepayment of RCC band and reinforcement shall be made for seperately).

13.4.2 : 12 mm cement plaster of mix:1:6 ( 1 cement : 6 coarse sand)

13.4.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.38 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

od183673/2019_2020 : Supply and install externally 1st quality 600x300x8mm ceramic tile walls cladding of cement ash or similar different colours, tile shall be laid and fixed to pre plastered walls in patterns, style and forms of grouting and jointing as directed by engineer using approved tile adhesive materials and pointed with approved tile joint filler matching the colour of tiles.

od183674/2019_2020 : Supply and install externally 1st quality 600x300x8mm brick pattern design colour ceramic tile wall cladding, tile shall be laid and fixed to pre- plastered walls in patterns, style and forms of grouting and jointing as directed by engineer using approved tile adhesive materials and pointed with approved tile joint filler matching the colour of tiles.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.82.2 : Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.50.3 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works

13.84.2 : Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.19 : Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

12.1.3 : Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/m2

9.147.5 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm)made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both havingwall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead ofappropriate dimension. (Area of window above 1.50 sqm).

9.147B.1 : 543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately).<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead ofappropriate dimension. (Area upto 0.75 sqm.)

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

od219382/2019_2020 : Supply and fix fully finished Pre Hung Door:- Both side HP Laminate vertical grain pattern Flush door with matching PVC wrapped WPC Jamb with front side Architrave other side tackers. Door of 35mm thick with 4 side edges painted / Lock Hole Boring (Using mortise lock)/ Hinge Rebate Cutting (4 Nos) ,Jamb width 100 mm. Latch with Lever handles without Keys SS finish - 1 No, Hinges 4&quot; x 3&quot; x 3mm SS finish - 4 Nos .Tower Bolt 6&quot; SS Finish - 1 No.(Jacsons or Approved equivalent)

od219378/2019_2020 : Supply and fix fully finished Pre Hung Door:-Both side Veneered (Sapeli/ Beech /RC Walnut/RC Teak etc) vertical grains Flush door with matching Veneer Wrapped Engineered wood Jamb (Frame) with front side Architraves and other side Tackers, all with specialised Lacquer Polish. Door of 35 mm thick with 4 side PVC Lipping / Lock Hole Boring (using mortise lock) / Hinge Rebate cutting (4 Nos.) /Extruded Sauerland core / Honey comb core filling. as per drawing and agreed schedule of rates inclusive of all applicable taxes to the satisfaction of site Engineer in charge.The above rate included all fixing and fiting lock, hinges,hardware items etc. ( Jacsons or approved equivalent)

od219371/2019_2020 : Supply and fixing ready made galvanized wooden texture Powder coating/Heat transfer/Fluorocarbon laminate painted steel doors with steel jamb,SS hinges &amp; door sill ,sheet thickness of 1to 1.4mm, Cylindrical lock, high security locking systems (Multi lock models having 11 locking points, and can be operated with a single key), honeycomb paper Infilling material, five years warranty on all the hardware and locking system as per satisfaction of site Engineer in charge.The above rate included all fixing and fittings like security locks, hinges, hardware items etc.( Cuirass/I-leaf/GM or approved equivalent.)

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

od15145/2019_2020 : Supply 100mmx100mmx14g thick 6.00 m long Galvanized square hollow section member (AS 1163-2009 Grade min C350L0 AS/NZS 4792 Galvanised coatings on ferrous hollow sections) fixed vertically and anchored to RC parapet and base up stand, will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer in-charge for approval before execution).

od17956/2019_2020 : Supply 50mmx50mmx16 g thick Galvanized square hollow section member (AS 1163-2009 Grade min C350L0 AS/NZS 4792 Galvanised coatings on ferrous hollow sections) fixed vertically and anchored to RC slab will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or more coats of epoxy paint (painting measured separately)(Shop drawings shall be submitted by the contractor to the Engineer in-charge for approval before execution).

od219426/2019_2020 : Supply Cor-Ten A grade 3mm thick warm rolled perforated cassettes (ASTM A606) fixed to plastered wall spacing in the hidden plastic suspension mounts with stainless steel class

od15420/2019_2020 : Providing and Fixing in position Ply Decking in class room of approved design, shape with vertical &amp; horizontal necessary frame work of hard wood members of approved quality, well notched &amp; screwed, 12mm thick approved marine ply decking finished to recieve marble / wood, necessary frame work, wooden packings, including necessary hardware, making holes in MS sections, etc. complete as per detail drawing and as directed by Enginner in charge.Raised floor @ 300mm ht. from FFL

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.59.1 : Providing and fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flanged of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45x15x0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27 mm high having flages of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of day wall screws of size 3.5x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitable fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with.a.8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through acutoclaving process.

17.2.1 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.4.1 : Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern

17.7.1 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.8 : Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

17.70.1 : Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

18.50.1 : Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

17.71 : Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

50.17.1.3 : Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

od219447/2019_2020 : Supply &amp; Fixing stainless steel square cockroach proof traps with Gratings MAT finish. Unloading materials supplied at site and storing it in safe place provided in the site. (Make:CHILLY/ ACO/SGS )

od219448/2019_2020 : Providing and fixing 100mm dia Cleanout with Spigot, with SS 304 Square Frame &amp; Round Frame with Flat Round Cover with Rubber Seal &amp; SS Screw including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer in charge at all levels.(Make:CHILLY/ ACO/SGS )

od219449/2019_2020 : Providing and fixing 75mm dia Cleanout with Spigot, with SS 304 Square Frame &amp; Round Frame with Flat Round Cover with Rubber Seal &amp; SS Screw including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer in charge at all levels.(Make:CHILLY/ ACO/SGS )

od15106/2019_2020 : Providing and fixing 75mm dia Cleanout with Spigot, with SS 304 Square Frame &amp; Round Frame with Flat Round Cover with Rubber Seal &amp; SS Screw including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer in charge at all levels.

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

50.18.8.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

50.18.7.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

50.18.7.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.7.5.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10 Kgf/cm2- Internal work- exposed on wall

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

od15107/2019_2020 : Supply and install Zoloto or approved equivalent 32mm full bore forged brass ball valve including all necessary fittings.

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.19.4.2 : Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreVertical

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

od15108/2019_2020 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per the direction of Engineer-in-Charge 160 mm dia 6 Kgf/cm2 - External work- Exposed on wall

od14994/2019_2020 : Extra over for Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all - round underground PVC pipes.

19.4.3.2 : Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:180x150 mm size P typeWith sewer bricks conforming to IS: 4885

18.48 : Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

FRONT GATE WITH SECURITY CABIN CIVIL WORKS

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

4.11 : Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.8 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

13.4.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.4.2 : 12 mm cement plaster of mix:1:6 ( 1 cement : 6 coarse sand)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.82.2 : Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

9.147.5 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm)made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both havingwall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead ofappropriate dimension. (Area of window above 1.50 sqm).

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

od219382/2019_2020 : Supply and fix fully finished Pre Hung Door:- Both side HP Laminate vertical grain pattern Flush door with matching PVC wrapped WPC Jamb with front side Architrave other side tackers. Door of 35mm thick with 4 side edges painted / Lock Hole Boring (Using mortise lock)/ Hinge Rebate Cutting (4 Nos) ,Jamb width 100 mm. Latch with Lever handles without Keys SS finish - 1 No, Hinges 4&quot; x 3&quot; x 3mm SS finish - 4 Nos .Tower Bolt 6&quot; SS Finish - 1 No.(Jacsons or Approved equivalent)

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.50.3 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works

13.84.2 : Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

COMPOUND WALL

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.2 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.8 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

13.4.2 : 12 mm cement plaster of mix:1:6 ( 1 cement : 6 coarse sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.82.2 : Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

13.84.2 : Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

od183674/2019_2020 : Supply and install externally 1st quality 600x300x8mm brick pattern design colour ceramic tile wall cladding, tile shall be laid and fixed to pre- plastered walls in patterns, style and forms of grouting and jointing as directed by engineer using approved tile adhesive materials and pointed with approved tile joint filler matching the colour of tiles.

ROADS AND ANCILLARY WORKS

16.1 : Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

16.78.3 : Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade - III ( size range 26.5 mm to 0.075 mm) having CBR Value - 20

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

51.16.PC.1pb : Primer Coat - Bitumen Emulsion (SS-1) - Using Packed Bitumen Rates <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 (low porosity).

od15002/2019_2020 : 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete ( tack coat to be paid for separately): With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt (DSR ITEM NO.16.33.1)

51.16.31.1.2 : Tack Coat - RS Bitumen Emulsion - On bituminous surface @ 0.25 kg /sqm <br> Providing and applying tack coat using bitumen emulsion conforming to IS : 8887, using emulsion pressure distributor including preparing the surface & cleaning with mechanical broom. <br> 1. With Rapid Setting Bitumen Emulsion <br> 2. On bituminous surface @ 0.25 kg /sqm

od15007/2019_2020 : Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG -10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete.(DSR ITEM NO 16.40)

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

od15027/2019_2020 : Providing and laying average 100 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate mixed with sand Zone V, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

16.42 : Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size ) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete

16.45 : Providing and fixing in position pre- moulded joint filler in expansion joints.

16.90 : Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

od15087/2019_2020 : two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

od15091/2019_2020 : Providing and fixing PVC pipe pieces in weep holes by hacking,jointing and make good, 110 mm pipe 4 kgf/cm2

od221523/2019_2020 : Construct foundation for lighting pole using M30 concrete of overall size 65x65x160 cm and 4 nos M20x75cm long anchor bolt set in concrete using 4mm thick anchor plate as per the drawing and specification.

od15098/2019_2020 : Construct RC drain using 1:1.5:3 mix wall and base 10cm thick of average inside dimensions 40cm wide x 60cm deep covered with 10cm (1:1.5:3) mix precast RC slab etc as per drawing and specification

LAND DEVELOPMENT

2.32 : Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.2.1 : Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead up to 50 m and lift up to 1.5 m:All kinds of soil

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

EXTERNAL WATER SUPPLY

50.18.9.6.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2

od14990/2019_2020 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling &amp; testing of joints complete as per direction of Engineer in Charge. 63 mm dia 10Kgf/cm2

od14994/2019_2020 : Extra over for Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all - round underground PVC pipes.

od221315/2019_2020 : Supply and install Zoloto or approved equivalent 50mm full bore forged brass ball valve including all necessary fittings

18.32.1 : Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

EXTERNAL SEWERAGE AND RAINWATER DRAINAGE

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

od14994/2019_2020 : Extra over for Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all - round underground PVC pipes.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

51.19.ST4 : Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately)<br> 4. 35 to 50 flush capacity

19.33 : Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

od17197/2019_2020 : Supplying and installing ready made Pre cast RCC Water tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (5000 L Capacity )

od17199/2019_2020 : Supply all material and construct RCC rain water filtration tank cum collection tank of overall size 7.6x2.40x2.45m using 1:1.5:3 concrete mix etc. all complete as per the drawing and specification.

od17218/2019_2020 : Supply ,Installation testing and commissioning of Kirloskar make model KOS 527+ or approved equivalent 5HP, 3 phase ,18m head 13.5 LPS capacity submersible pump including all accessories.

EXISTING CLASS ROOMS CONVERTED TO SMART CLASS ROOMS

14.46 : Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

14.53.1 : Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

14.54.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

UPGRADATION OF EXISTING MAIN BUILDING AND WORKSHOPS

14.46 : Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

14.53.1 : Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

14.54.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

od15463/2019_2020 : Providing and fixing PUF insulated sandwich panels for roof Having top profile sheet with 28-30mm crust hight at 195-200mm pitch, inner liner tray and PUF Insulation between not less than 50 mm thick and width 980mm. Panel shall have 0.50mm thick Galvalume sheet on both side of polyurethane foam confirming to IS 12436:1988 with standard profile&lt;br&gt;with tongue &amp; groove arrangement, The PU foam shall be self-extinguishing, fire retardant type having minimum density of 40 Kg/cum(+,-2 Kgs) including CFC Free pannel should be GRIHA Certified.The panels shall be fixed to the steeL frame structure with minimum 5mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/c assembly/ the cost shall include ridge, soffit junctions &amp; flashings as specified puff panel makers.

od147354/2019_2020 : Supply and installation of High performance Industrial Roof-Vents(600 mm Dia. self driven roof ventilator) made of aluminum alloy Air Vent, designed to meet AS-2428.1.1993 to wind speed of 200Km/hr and to the entry of wind driven rain at a range of 2.5 L/sec. Under cyclone condition. Roof vents to be fixed on standing seam profile with engineering detail to be designed to make total system as leak proof and to the satisfaction of engineers in-charge.

4.1.2 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

od221316/2019_2020 : Mat polished finish on concrete surface by flooring the process &quot;DENSIFIED FLOOR&quot; Vid. as Grinding the concrete floor using Coarse, Medium diamond grinding tools for removing the latency and minor level difference and opening up the pores in concrete, Densification of the floor using hybrid densifier, Densifier reacts with the UN-hydrated lime present in concrete and makes the concrete surface dense and hard.It offers many benefitssuch as reduced dusting, higher gloss readings, increased abrasion resistance, and a longer lifespan of the concrete floor. For this to achieve, the concrete floor is allowed to be saturated with densifier, sealing with external grade sealer is applied on the floor after polishing to protect the floor from the effects of weather and to make the floor water repellent and stain resistant, burnishing the floor using a floor burnisher to bring about more shine and remove excess sealer from the floor etc in compliance to ASTM C-779 - Standard test method for abrasion resistance on horizontal floor surfaces. This item shall be executed only by the agency which has all required manufacturing machinery and necessary expertise.

SIGNAGE AND BOARDS

od221527/2019_2020 : Providing and fixing of Advance Direction / Way finding / Reassurance Sign board of size 1000 mm x 1500 mm made out of Type-XI encapsulated lens type retro reflective sheeting wide. Base Sheeting shall be of White Color type IV class B retro reflective sheeting fixed over 2 mm thick Aluminium Composite Material sheet with area exceeding 0.9 sqm fixed over back support frame of M.S.Angle 35 x 35 x 5 mm all round mounted on two 50 mm dia MS Pipe with clear height of not less than 2.1 m from the ground level to the bottom of the board as per approved drawings.&lt;br&gt;The sign post should be painted with one coat of red oxide paint and two coats of 1 st quality synthetic enamel paint Black &amp; white colour with bands of 30 cm height. The sign post shall be firmly fixed in to the ground by means of properly designed foundation with M15 grade concrete size 450mm x 450mmx 600 mm, including cost,conveyance of all materials, equipment,machinery and labour with all leads and lift,loading charges necessary for satisfactory completion of the work as directed by Engineer in-Charge.

od221528/2019_2020 : Supply and fixing sticker type signage at site (on door or similar locations) in proper line &amp; level. The signage letters shall be made with premium quality vinyl sheet of approved colour, pasted on &ldquo;3M&rdquo;make self-adhesive film of approved colour, including supply of all material labour etc. required for proper completion of work. Before making the signage text &amp; font of letters in best fit size will be set in computer so as to give aesthetic look as per sample available with ITD

od221529/2019_2020 : Supply and fixing bilingual signage in English. The signage letters will be made with premium quality vinyl sheet of approved colour, pasted on 3mm thick aluminium composite panel backing. The signage will be either fixed on the wall with the screws &amp; double tape or hanged from the false ceiling with the help of hooks &amp; chains complete work.

od221530/2019_2020 : Supply &amp; fixing 5 mm thick aluminum compressed Panel (ACP) sheet in the required size for building name signage. The sheet will be cut into size as per the size of signage to be fixed in position (Stone fa&ccedil;ade, grit wash, gypsum board etc.) with screws &amp; tape including s/o all material labour T&amp;P etc. required for proper completion of work.

od221531/2019_2020 : Supply &amp; fixing stainless steel (SS) letters made with SS-304 grade 20 gauge sheet as per the approved size &amp; shade including fixing on ACP sheet in required height line &amp; level including s/o all T&amp;P etc. required for proper completion of work. Before making the letters the font &amp; size will be got approved from ITD.

od221532/2019_2020 : Supply and fixing symbol signage such as No. Smoking, No Spitting, Drinking Water etc. signage of standard sizes as per conventional design/ colour code on 3 mm thick aluminium composite panel. The signage will be either fixed on the wall with the help of screws &amp; double tape or hanged from the false ceiling with the help of chain &amp; screws etc. complete work.

od221533/2019_2020 : Printing of floor plans on approx. A2 size poster sheet with indelible ink framing the same in 3mm thick acrylic sheet and 1&rdquo; studs complete. The floor plans will be fixed on the wall with the help of screws and double tape etc. to give neat &amp; finished look

MAIN BUILDING FURNITURE

od146712/2019_2020 : Supply, deliver and place trademark registered branded (JALARAM make JED 1512) or approved equivalent Executive Desk with side unit and credenza. Desktop mounted on SS tubular legs and specially designed pedestal storage with utility spaces inspired by your needs. Size: (A) Main Desk : W-2000 x D-900 x H-750 mm (B) Side Unit : W-1050 x D-500 x H-750mm (C) Credenza : W-2000 x D-400 x H-l19Omm

od146713/2019_2020 : Supply, deliver and place registered branded (JALARAM make JED 220) or approved equivalent Executive Desk elegant looking main desk with mobile pedestal and return unit. A real beauty of the blend of wood and steel. Main Desk Size: W-180 &times; D-90 &times; H-75 (cm) Joining Top (Black Finish) Size: W-105 &times; D-120 (cm) Fixed Side Return Desk Size :W-120 &times; D-60 &times; H-72(cm) Mobile Pedestal Size: W-40.5 &times; D-57 &times; H-50(cm).

od146714/2019_2020 : Supply, deliver and place Trademark registered branded (JALARAM make-JED 200) or approved equivalent Chief Executive Suite with PU coated 36 mm post formed top, Executive Return Unit &amp; 3 Drawer Pedestal Unit,Size of the main Table: W-250 &times; D-110 &times; H-75 cm, Size of the Pedestal for Main Table: W-42.5 &times; D-80 cm, Size of Return Unit: W-127.5 &times; D-58 cm ,Size of the Pedestal for Return Unit: W-42.5&times;D-58 cm

od146715/2019_2020 : Supply, deliver and place registered branded (JALARAM Make-JEC 2017(D)) or approved equivalent Executive High Back Revolving Chair, Tested by approved BIFMA standard laboratories confirming to ANSI/BIFMA X 5.1- 2002 Cl. No. 5,7,8,12,13,17 on functional requirement. Leatherette Finish, High quality mould foam cushion, Die-Cast Aluminium with buffing pedestal, 5 Position locking system with swivel mechanism, Chrome Finished Armrest, Anti-Shock and Synchro Tilt Mechanism , Adjustable cozy armrest , Overall Size (approx) :-H: 117.0 - 126.5 x W:75 x D:75 (cm) ,Seat Height:- 44-54 (cm) Front Pivot Synchro Mechanism: This mechanism helps you experience the effect of your body angle opening out, for maximum relaxation, while your feet remain firmly on the ground. 5-Position Locking: The backrest can be locked in 5 different positions, giving you firm support for concentrated work. Its anti-shock mechanism prevents the backrest from impacting the user when the lock is released. Moulded Foam: The seat and the backrest are made up of moulded polyurethane foam of the right density and thickness, which not only gives you a soft feeling on first contact but also provides a firm support to ensure hours of comfortable seating, Swivel Mechanism: The swivel mechanism allows for a complete 3600 lateral movement. This prevents you from straining over your shoulders and back to reach out for papers and phones kept on either side of your table, ensuring mobility while working. Twin Wheel Castors: The twin wheel castors facilitates ease of movement.

od146716/2019_2020 : Supply, deliver and place registered branded (JALARAM Make-JEC 2017(F)) or approved equivalent Executive Visitor Chair, Tested by approved BIFMA standard laboratories confirming to ANSI/BIFMA X 5.1- 2002 Cl. No. 5,7,8,12,13,17 on functional requirement. With Leatherette Finish Moulded Foam: The seat and the backrest are made up of moulded polyurethane foam of the right density and thickness.

od146717/2019_2020 : Supply, deliver and place trademark registered branded (JALARAM make- JSF 102 A) or approved equivalent JALARAM Multipurpose storage cabinet with 2 adjustable shelves and 1 full locker. Overall size: H-1980 &times; W-915 &times; D-485(mm) (H-78&quot;&times;W-36&quot;&times; D-19&quot;) Material Specifications: The raw material used in cupboard will be PRIME quality CRCA as per IS 513 (1994,1998) &lsquo;D&rsquo; grade. OEM must enclose Proof of purchase of steel from SAIL/Tata Steel/Essar/ Jindal. The cupboard should have welded construction with MIG welding process. The material used for constructing the cupboard should be prime quality Cold Rolled Close Annealed (CRCA) Steel (for doors and shelves 1.0 mm &amp; other parts as per functional requirements) The doors provided will be full height steel hinged doors The handle provided will be matching, easy to grip, sleek and elegant. The Cupboard will have a 3 way locking Mechanism Minimum 6 levers (With duplicate keys) mechanism with shooting bolt arrangement. Shelving: The shelving will be Height wise Adjustable and Shelf Mounting. The Uniformly Distributed Load (UDL) Capacity per each full shelf will be 40 Kg at least. The cupboard will have 2 numbers of adjustable and 1 fixed full shelves with 1 full locker. All steel parts will be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust.

od146718/2019_2020 : Supply, deliver and place Trademark registered branded (JALARAM Make-jss 905) or approved equivalent Sofa Set, Overall Size of 3 seater: H-736 x W-2134 x D-812 mm

od146719/2019_2020 : Supply, deliver and place Trademark registered branded (JALARAM make-JED 204 (A)) or approved equivalent Executive table, both side storage unit of special size. 2 drawers cum filing drawer &amp; a center drawer, mounted on telescopic channel. Overall Size of curvica top: W-180 &times; D-90 cm ,Height of table 72.5 (cm) Material Specification: Two pedestals having 2 box drawers and 1 filing drawer with independent locking arrangement (cam lock) for each pedestal. Drawers shall have a clear depth of &gt; 400 mm. One center drawer having ~ 350 mm clear depth with independent locking arrangement. The top should be made of 25 mm thick Pre&dash; laminated board(PLB) of TESA with 2 mm thick matching lipping. Under Structure: Two pedestals shall be a combination of processed wood (PLB) and Mild Steel (MS). Pedestal shell to be 0.80 mm thick MS sheet. Drawer tray to be made from 0.6 mm thick M.S sheet. Drawer separator to be made from 0.6 mm thick M.S. sheet. PLB drawer fronts (18 mm thick PLB) to match the top colour. Drawers to be mounted on double extension steel telescopic ball slides to give full access to the drawer. Sleek handles for easy grip. Glides screws for leveling.Stiffeners (1.6 mm thick) is to be provided under the top to give additional strength. Powder coating: Powder coating on all items with dry film thickness not less than 50 microns, Salt Spray test to withstand more than 1000 hours, Pencil scratch hardness more than 2H, Adhesion as per DIN 53152 Standards. The powder coating shall be of good quality (7 process) to ensure good adhesion of life of the coating. Modesty: Shall be made from 1.0 mm thick MS. Panel recessed inside for more leg room. Panel to be styled with cut&dash;outs (windows) for better physical appearance.

od146720/2019_2020 : Supply fabricate and install LGS or approved equivalent Make Conference table [36&apos;W x 4&apos; D] with Top/Vertical support legs are to be made of 25mm thk Particle board duly laminated with approved colour with 2mm thk. Matching PVC edgeband and modesty are 18mm thk prelamianted particle board with edgebanded finish.Set with 14 nos of LGS Make Conference Chairs Nylon Back With Imported Fire Retardant Mesh, Adjustable Arms With Soft P.U Pad, Nylon Base With Nylon Wheels, Synchro Tilt Single Locking, 100mm Gas Lift, PU Foam Seat With Desired Fabric.

od146721/2019_2020 : Supply, deliver and place Trademark registered branded (JALARAM make-JSF 215(A) or approved equivalent Office Table Overall Size: 60&rdquo;L x 30&rdquo;D x 29.5&rdquo;H inch Material Description:- Main top of 25mm thick. Wood based high quality Pre-laminated ,Particle Board(PLB) of TESA with 2mm PVC edge band by hot melt glue process for beading all over edge. Table top C frame of 20swg. CRCA sheet IS 513. Leg tube &amp; footrest of 25 x 25x 1.2mm thick (18swg.) ERW square MS tube. 3 Drawer unit &amp; Locker unit of 22swg. &amp; 23swg. CRCA sheet IS 513 with good quality lock &amp; PVC handle. Good quality PVC shoes at bottom. All steel parts will be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust treatment and B grade phosphating .

od146722/2019_2020 : Supply, deliver and place of Trademark registered branded (JALARAM make- JMPT 4A) or approved equivalent Table for with 25 mm top, square tubular frame. Overall size: W-151 x D-90 x H-75(cm) Material Description: Main top 25mm thick wood based high quality Pre-laminated Particle Board(PLB) of TESA with 2mm PVC edge band by hot melt glue process for beading all over edge. Top frame of 1.21mm thick. (18swg) CRAC sheet IS 513. Table frame structure made up of prime quality MS ERW square tube 25x25mm of 18swg. Good quality PVC Shoes. All steel parts should be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust treatment and B grade phosphating.

od146723/2019_2020 : Supply deliver and place Trademark registered branded (JALARAM Make-JSD 601(D))/equilvalent Two Seater Desk Cum Bench fitted on tubular frame with perforated seat and back for Senior Students.Overall size : H-760 &times; W-1040 &times; D-1000 (mm) Seat Height: 460 mm Desk Top (Curvica) of 25 mm thick wood based high quality branded (TESA) post formed Pre-laminated Particle Board (PLB )with 0.6mm laminated with 2mm PVC beading by hot melt glue process all over 4 edges. Bench Main frame tube &amp; Support tube of 32mm, 16swg ERW round tube. Seat &amp; Back frame tube of 19mm, 16swg ERW round tube. Seat &amp; Back support of 25x25x1.6mm (16swg) thick. square ERW tube. Seat &amp; Back of 18swg. Perforated CRCA sheet IS 513. Storage Bucket of 18swg. Perforated CRCA sheet IS 513. Good quality PVC shoes &amp; cap. All steel parts will be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust treatment and B grade phosphating.

od146724/2019_2020 : Supply,deliver and place Trademark registered branded (JALARAM Make JEC 501(C))/Equivelent Executive Visitor Net Chair, Overall Size (approx): H-98 x W-58 x D-63.5 (cm) Seat Height: 48 (cm) Frame structure: Backrest made of Mesh and Seat from hot mould plywood of minimum 12 mm thickness of ergonomic design to avoid back pain. Chrome-plated Arm &amp; Frame &apos;Tapestry: Minimum average weight required 400 to 490 gms per sq. mtr. Tapestry will be tested quality such as stain test, ultra violet test,glue test and color fastening with average weight of 450 grams per square meter Cushioning: PU foam having density of 50 kgs/m3 for seat. Average thickness of foam not less than 50 mm + 10 mm Polly foam. Arm rest material: Polyurethane on Chrome Shoes: Nylon Rubber

od146725/2019_2020 : Supply and fixing White Board: 4&apos;x6&apos; magnetic White

od146726/2019_2020 : Sypply and installation of Podium : 600x600x 1200mm ht.

FURNITURE FOR EXISTING CLASS ROOMS CONVERTED TO SMART CLASS ROOMS

od146724/2019_2020 : Supply,deliver and place Trademark registered branded (JALARAM Make JEC 501(C))/Equivelent Executive Visitor Net Chair, Overall Size (approx): H-98 x W-58 x D-63.5 (cm) Seat Height: 48 (cm) Frame structure: Backrest made of Mesh and Seat from hot mould plywood of minimum 12 mm thickness of ergonomic design to avoid back pain. Chrome-plated Arm &amp; Frame &apos;Tapestry: Minimum average weight required 400 to 490 gms per sq. mtr. Tapestry will be tested quality such as stain test, ultra violet test,glue test and color fastening with average weight of 450 grams per square meter Cushioning: PU foam having density of 50 kgs/m3 for seat. Average thickness of foam not less than 50 mm + 10 mm Polly foam. Arm rest material: Polyurethane on Chrome Shoes: Nylon Rubber

od146722/2019_2020 : Supply, deliver and place of Trademark registered branded (JALARAM make- JMPT 4A) or approved equivalent Table for with 25 mm top, square tubular frame. Overall size: W-151 x D-90 x H-75(cm) Material Description: Main top 25mm thick wood based high quality Pre-laminated Particle Board(PLB) of TESA with 2mm PVC edge band by hot melt glue process for beading all over edge. Top frame of 1.21mm thick. (18swg) CRAC sheet IS 513. Table frame structure made up of prime quality MS ERW square tube 25x25mm of 18swg. Good quality PVC Shoes. All steel parts should be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust treatment and B grade phosphating.

od146723/2019_2020 : Supply deliver and place Trademark registered branded (JALARAM Make-JSD 601(D))/equilvalent Two Seater Desk Cum Bench fitted on tubular frame with perforated seat and back for Senior Students.Overall size : H-760 &times; W-1040 &times; D-1000 (mm) Seat Height: 460 mm Desk Top (Curvica) of 25 mm thick wood based high quality branded (TESA) post formed Pre-laminated Particle Board (PLB )with 0.6mm laminated with 2mm PVC beading by hot melt glue process all over 4 edges. Bench Main frame tube &amp; Support tube of 32mm, 16swg ERW round tube. Seat &amp; Back frame tube of 19mm, 16swg ERW round tube. Seat &amp; Back support of 25x25x1.6mm (16swg) thick. square ERW tube. Seat &amp; Back of 18swg. Perforated CRCA sheet IS 513. Storage Bucket of 18swg. Perforated CRCA sheet IS 513. Good quality PVC shoes &amp; cap. All steel parts will be epoxy polyester powder coated to the thickness not less than 50 microns finish after 10 tank anti-rust treatment and B grade phosphating.

od146726/2019_2020 : Sypply and installation of Podium : 600x600x 1200mm ht.

MAIN BUILDING GROUND FLOOR ELECTRICAL WORKS

od134264/2019_2020 : Supply of 240 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od134265/2019_2020 : Supply of 120 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od134266/2019_2020 : Supply of 70 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od134267/2019_2020 : Supply of 25 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od134268/2019_2020 : Supply of 10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.8 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 16 sq. mm (25mm)

7.1.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

4.1.3 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

14.14.2 : Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.150 mm dia

5.4 : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, andproviding masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

od134401/2019_2020 : Providing and fixing 25 mm X 3 mm copper strip on surface or in recess for connections etc. as required.

od134402/2019_2020 : Supplying and laying 25 mm X 3 mm copper strip at 0.50 metre below ground as strip earth&lt;br&gt;electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.&lt;br&gt;(Jointing shall be done by overlapping and with 2 sets of brass nut bolt &amp; spring washer spaced at 50mm)

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

90.11.1.11 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

90.11.1.12 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

90.11.1.14 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

90.11.1.16 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.15.1 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.24.8 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

90.2.1.6 : Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Combined plug point with 6 A, 5 pin plug socket controlled by 6 A, switch in the same switch board as that of light points

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

90.4.5.2 : Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.

90.3.19.3 : Supply conveyance, installation, testing and commissioning the light fittings of following types made from CRCA sheet 0.5mm thickness with all accessories and lamps directly on wall and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required

90.3.24.3 : Supply & installation of light fittings suspended on ball & socket arrangement with 19 mm down rod <br> Supply, conveyance, installation, testing and commissioning the light fittings of following types made of .5mm thick CRCA sheet accessories and lamps etc. including supplying and fixing ball and socket arrangements on PVC round block, suspension down rod of 19mm dia MS conduit up to 2x30cm length including painting and wiring the down rod with 16/0.20mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connections etc. a required.

90.4.1 : Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

2.21 : Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

od133961/2019_2020 : SITC of 100 KVA DG set with standard control panel complete with all other accessories as required.

od163325/2019_2020 : SITC of Rust resistant and weather proof Bulk-head light fixture with 9W LED lamp, IP 65 Protection complete with all other accessories as required. (Make: crompton)

od163326/2019_2020 : Supply, installation, testing and commissioning of 5W LED lamp (Make: Luker, Model: LBPC05CL) working on 230V, 50Hx AC, including giving connections as required.

od168074/2019_2020 : SITC of MSB new (Kannur)&lt;br&gt;Supply, installation , testing and commissioning of totally enclosed compartmentalized dust and vermin proof cubical segregated and modular in construction M.V. panel board free standing fabricated with14swg and 16swg of CRCA M.S. sheet, powder coated , bus-bar chamber ,outgoing switchgear etc. (all feeder unit Would be compart mentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, ( bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent.&lt;br&gt;Incomer: 630A, 4P Isolator, Busbar: 630A, Aluminium TP&amp;N busbar, Outgoing: 200A, 36kA, 4P MCCB - 2 Nos.

od168082/2019_2020 : SITC of MAIN PANEL (Kannur)&lt;br&gt;Supply, installation , testing and commissioning of totally enclosed compartmentalized dust and vermin proof cubical segregated and modular in construction M.V. panel board free standing fabricated with14swg and 16swg of CRCA M.S. sheet, powder coated , bus-bar chamber ,outgoing switchgear etc. (all feeder unit Would be compart mentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, ( bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent.&lt;br&gt;Incomer: 200A, 36kA, 4P MCCB - 1 No, 250A, 4P Isolator - 1 No&lt;br&gt;200A 4P Contactor &amp; 150A, 4P Contactor&lt;br&gt;AMF relay with electrical interlock&lt;br&gt;200A Al bubar for 3 phase and neutral.&lt;br&gt;Outgoing: 125A, 25kA, 3P, MCCB - 1No&lt;br&gt;100A, 25kA, 3P MCCB - 3 No.&lt;br&gt;160A, TPN Isolator - 1 No.&lt;br&gt;50A 25kA 3P MCCB - 2 no

od168125/2019_2020 : SITC of SSB1 - Classroom building ( Kannur)&lt;br&gt;Supply, installation , testing and commissioning of totally enclosed compartmentalized dust and vermin proof cubical segregated and modular in construction M.V. panel board free standing fabricated with14swg and 16swg of CRCA M.S. sheet, powder coated , bus-bar chamber ,outgoing switchgear etc. (all feeder unit Would be compart mentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, ( bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent.&lt;br&gt;Incomer: 150A, TPN Isolator&lt;br&gt;Busbar - 150A Al for 3 phases and neutral&lt;br&gt;Outgoing: 63A, 16kA, 3P MCCB - 1 No&lt;br&gt;50A, 16kA, 3P MCCB - 5 Nos.&lt;br&gt;32A, 16kA, 3P MCCB - 1 No

od168143/2019_2020 : SITC of SSB 5 - Fifa ground lighting, feeder pillar, gate DB ( Kannur)&lt;br&gt;Supply, installation , testing and commissioning of totally enclosed compartmentalized dust and vermin proof cubical segregated and modular in construction M.V. panel board free standing fabricated with14swg and 16swg of CRCA M.S. sheet, powder coated , bus-bar chamber ,outgoing switchgear etc. (all feeder unit Would be compart mentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, ( bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent.&lt;br&gt;Incomer: 150A, TPN Isolator&lt;br&gt;Busbar - 150A Al for 3 phases and neutral&lt;br&gt;Outgoing: 40A SP MCB 10kA - 3 no&lt;br&gt;40A 3P MCB 10kA - 1 no&lt;br&gt;63A 16kA 3P MCCB - 2 no

od168204/2019_2020 : Supply, Installation, Testing and commissioning of 15 KVA UPS with 1 hour battery back up complete with all accessories as required.

7.10 : Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate withinscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixingthe same in ground as required.

FRONT GATE WITH SECURITY CABIN ELECTRICAL WORKS AND COMPOUND WALL LIGHTING

90.11.1.10 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 ampsmodular switch, connection etc. as required. (For light plugs to be used in non residentialbuildings).

1.32 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

od134531/2019_2020 : Supply, installation , testing and commissioning of Wall fan of 300mm sweep dia on wall, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the Wall fan.&lt;br&gt;300mm sweep wall fan working on 230 V A/C&lt;br&gt;

7.3.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.Upto 35 sq. mm

od134546/2019_2020 : Supply of 10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

14.14.2 : Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.150 mm dia

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

od163332/2019_2020 : SITC of 3W LED Recessed Spot light pre wired, working on 230V, 50Hz AC, complete with all other accessories as required.

od163333/2019_2020 : SITC of 20/25W LED Surface mounting down light, working on 230V, 50Hz AC, complete with all other accessories as required.

od163334/2019_2020 : SITC of weather proof pillar light fittings with 9W LED lamp, IP65 for outdoor purpose pre wired and complete with all other accessories as required.

od163335/2019_2020 : Supply, installation, testing and commissioning of LED 3W Spike light, IP65 with all other accessories as required.

od163326/2019_2020 : Supply, installation, testing and commissioning of 5W LED lamp (Make: Luker, Model: LBPC05CL) working on 230V, 50Hx AC, including giving connections as required.

EXTERNAL LIGHTING

7.3.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.Upto 35 sq. mm

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

od134936/2019_2020 : Supply of 4 sqmm 3 core PVC/ XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od134937/2019_2020 : Supplying and laying 8 SWG Cu wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

od134938/2019_2020 : Supply of 16 sqmm 3 core PVC/ XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

9.1.8 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 16 sq. mm (25mm)

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

od163348/2019_2020 : SITC Of Legrand make feeder pillar complete with the following accessories. &lt;br&gt;Incomer: 40A, DP Isolator. 40A, DP, RCCB, 100mA. Timer control with contactor. Auto/ Manual switch. &lt;br&gt;Outgoing: 10A, SP MCB - 4 Nos.

od163349/2019_2020 : Supply installation testing commissioning of 6 meter Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III single arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc. with 45W LED street light output greater than 105lumen/W 4000-6000 K with IP 65/66 protection complete with all other accessories as required.

90.16.2.5 : Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.50 mm dia. G.I. pipe (medium class)

ADMINISTRATIVE BUILDING GROUND FLOOR HVAC SYSTEM WORKS

od163371/2019_2020 : Supply and fixing of drain pipe for HVAC units

od163372/2019_2020 : Supply and installation of Refrigerant Copper piping insulated with Nitrile Rubber Tubular insulation with 13/19mm thickness.

od163376/2019_2020 : Supply &amp; installation of Modular type outdoor units equipped with minimum 2 Nos of highly efficient compressors with all inverter type compressor(s) only,special acryl pre-coated heat exchanger,low noise condenser fan,auto check function for connection error,auto address setting,with multiple outdoor units of capacities and quantities as mentioned below.Refrigerant Should be R410A .(4 HP CARRIER 3 PHASE COMPRESSOR)

od163392/2019_2020 : Supply &amp; installation of High-wall indoor units with compact cooling coil,electronic expansion valve and multi speed fan motor,The blower shall be dynamicaly balanced and designed for silent operation ,the filters shall be washable type .Drain Pump is a part of the indoor unit.(1 TR Carrier VRF Indoor Unit )

od212814/2019_2020 : Supply &amp; installation of 1.00 TR Split A/C with high wall mounted unit . [Mini 3 * Star rating] Copper Condenser Only ( Make: Carrier HW split AC/ Hitachi/ Bluestar)

ELV SYSTEM

od134828/2019_2020 : SITC of PANASONIC KX-TA 824 24 port hybrid analog Telephone systen control unit intercom with 16 extensions

od134829/2019_2020 : Supply, Installation, Testing and commissioning Of distribution box for CCTV 6Ux600Wx600D With Front Glass Door,Side Openable Panels with Lock &amp; Key,4Way 5A PDU,1U Cable Manager,Cooling Fan,H/W Kit10

od134830/2019_2020 : &nbsp;SITC Of 350W RMS MIXER AMPLIFIER, 3 MIC, 2 AUX, 100V/70V AND 4OHMS , BALANCED MIC,FREQUENCY RESPONSE (50 HZ-16000HZ),S/N RATIO-MIC1,2,3,4:66DB;AUX 1:80 DB,THD-LESS THAN 1% AT 1 KHZ,1/3 RATED POWER, MUTING FUNCTION-MIC 1 OVERRIDES OTHER INPUT SIGNALS WITH 0-30 DB ATTENUATION,CONTROLS-INDIVIDUAL GAIN CONTROLS, POWER SWITCH;BASS: 10DB AT 100HZ,TREBLE: 10DB AT10000HZ.

od134831/2019_2020 : Supply Installation testing and Commissioning of 10/100/1000 Mbps 24 Port Network Switch to provide networks and internet on class room etc

od134832/2019_2020 : Supply, installation, testing and commissioning of Bio Metric Finger Print scan attendance system with LCD/LED display &amp; keypad &amp; TCPIP LAN, USB Connectivity along with Attendance monitoring &amp; report software (Web based Terminal)&lt;br&gt;

od134833/2019_2020 : Supply and laying of Cat6 outdoor cable including necessary connectors&lt;br&gt;

od134834/2019_2020 : Supply, Installation, Testing and commissioning of 6W Wall mount speakers with perforated metal grille with line matching transformer suitable for 4 ohm impedance 200 mm dia LBD 0606/10

od134835/2019_2020 : Supply, installation, testing and commissioning of 24 Port 10/100/1000 Mbps PoE Switch.

od134836/2019_2020 : Supply, installation, testing and commissioning of LAN socket.

od134837/2019_2020 : Supply, installation, testing and commissioning of 20 PAIR BOX WITH KRONE MODULES

od134838/2019_2020 : Supply &amp; Installation of telephone cable 10 pair through PVC conduit.

od134839/2019_2020 : Supply &amp; Installation of UG telephone cable jelly filled, 10 pair

od134840/2019_2020 : Supply,Installation, Testing &amp; commissioning of Telephone of approved makes including all other accessories for connection.

od134841/2019_2020 : Supply, installation, testing and commissioning of Telephone socket.

od134842/2019_2020 : Supply, Installation, Testing and commissioning of Distribution box for PA distribution made out of 16 SWG CRCA sheet with lockable door arrangement having connectors (10 NOS) suitable for 1.5sqmm wire with facity for cable termination of 4cx10 sqmm ALAR. Required at each floor for PA wire termination.

od134843/2019_2020 : Supply, Installation, Testing and commissioning of XLR cables and connectors

od134844/2019_2020 : Supply &amp; laying of twin twisted 2x1.5 sqmm Cu flexible wire 1.1 kv grade PVC insulated through PVC conduit.

od134845/2019_2020 : Supply, installation, testing and commissioning of indoor IR IP dome camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines.

od134846/2019_2020 : Supply, installation, testing and commissioning of Outdoor IR IP bullet camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity,with IR 480TV lines.

od134847/2019_2020 : Network Video Recorder:&lt;br&gt;Providing &amp; fixing Network Video Recorde 32-channel 720P or 24-channel 1080P high definition network video input and storage Support simultaneous HDMI and VGA output, resolution up to 1920&times;1080P/60Hz Supports 256Mbps bandwidth throughput handling, Supports 4-channe, 1080P video real-time decoding and synchronous playback Supports 8 SATA hard disk with capacity up to 4TB.

od134848/2019_2020 : Supply, installation, testing and commissioning of 32&quot; Flat Screen VGA Color Monitor.&lt;br&gt;

od134849/2019_2020 : Supply and drawing of CAT6 4 pair cable including all necessary connector.

od134850/2019_2020 : Supply, Installation, testing and commissioning of Cat6 24 Port un loaded Patch Panel.

od134851/2019_2020 : Supply, installation, testing and commissioning of Cat6 I/O for Patch Panel Shuttered.

1.18.2 : Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od136286/2019_2020 : SITC of D-Link (DIR-878) AC1900 MU-MIMO 1900Mbps Wi-Fi Router (Without Modem)

NEW SMART CLASS ROOM (ELECTRICAL WORKS - 2 NOS)

od134832/2019_2020 : Supply, installation, testing and commissioning of Bio Metric Finger Print scan attendance system with LCD/LED display &amp; keypad &amp; TCPIP LAN, USB Connectivity along with Attendance monitoring &amp; report software (Web based Terminal)&lt;br&gt;

od134834/2019_2020 : Supply, Installation, Testing and commissioning of 6W Wall mount speakers with perforated metal grille with line matching transformer suitable for 4 ohm impedance 200 mm dia LBD 0606/10

od134836/2019_2020 : Supply, installation, testing and commissioning of LAN socket.

od134844/2019_2020 : Supply &amp; laying of twin twisted 2x1.5 sqmm Cu flexible wire 1.1 kv grade PVC insulated through PVC conduit.

od134845/2019_2020 : Supply, installation, testing and commissioning of indoor IR IP dome camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines.

od134849/2019_2020 : Supply and drawing of CAT6 4 pair cable including all necessary connector.

od133837/2019_2020 : Supply, installation, testing and commissioning of Promethean Board AB2T78 complete with all other accessories. Active inspire software will be complimentary with Promethean board.

od133834/2019_2020 : Supply, installation, testing, and commissioning of LT Projector and roof mount for LT projector complete with all accessories as required.

SMART CLASS ROOM EXISTING (ELECTRICAL WORKS - 12 NOS)

od134832/2019_2020 : Supply, installation, testing and commissioning of Bio Metric Finger Print scan attendance system with LCD/LED display &amp; keypad &amp; TCPIP LAN, USB Connectivity along with Attendance monitoring &amp; report software (Web based Terminal)&lt;br&gt;

od134834/2019_2020 : Supply, Installation, Testing and commissioning of 6W Wall mount speakers with perforated metal grille with line matching transformer suitable for 4 ohm impedance 200 mm dia LBD 0606/10

od134836/2019_2020 : Supply, installation, testing and commissioning of LAN socket.

od134844/2019_2020 : Supply &amp; laying of twin twisted 2x1.5 sqmm Cu flexible wire 1.1 kv grade PVC insulated through PVC conduit.

od134845/2019_2020 : Supply, installation, testing and commissioning of indoor IR IP dome camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines.

od134849/2019_2020 : Supply and drawing of CAT6 4 pair cable including all necessary connector.

od133837/2019_2020 : Supply, installation, testing and commissioning of Promethean Board AB2T78 complete with all other accessories. Active inspire software will be complimentary with Promethean board.

od133834/2019_2020 : Supply, installation, testing, and commissioning of LT Projector and roof mount for LT projector complete with all accessories as required.

od134996/2019_2020 : Supply, Installation, testing and commissioning of Cat6 16 Port un loaded Patch Panel.

od134997/2019_2020 : Supply, installation, testing and commissioning of 16 Port 10/100/1000 Mbps PoE Switch.

od134851/2019_2020 : Supply, installation, testing and commissioning of Cat6 I/O for Patch Panel Shuttered.

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.32 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

od135045/2019_2020 : Supply, installation, testing and commissioning of wall mounted 15Ux600Wx600D With Front Glass Door With Lock &amp; Key,Side Openable Panels with Lock &amp; Key,6Way 5A PDU,1U Cable Manager,Cooling Fan,H/W Kit10

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 ampsmodular switch, connection etc. as required. (For light plugs to be used in non residentialbuildings).

od134830/2019_2020 : &nbsp;SITC Of 350W RMS MIXER AMPLIFIER, 3 MIC, 2 AUX, 100V/70V AND 4OHMS , BALANCED MIC,FREQUENCY RESPONSE (50 HZ-16000HZ),S/N RATIO-MIC1,2,3,4:66DB;AUX 1:80 DB,THD-LESS THAN 1% AT 1 KHZ,1/3 RATED POWER, MUTING FUNCTION-MIC 1 OVERRIDES OTHER INPUT SIGNALS WITH 0-30 DB ATTENUATION,CONTROLS-INDIVIDUAL GAIN CONTROLS, POWER SWITCH;BASS: 10DB AT 100HZ,TREBLE: 10DB AT10000HZ.

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

od134974/2019_2020 : Supply, installation, testing and commissioning of 10/100/1000 Mbps 16 Port Network Switch to provide networks and internet on class room etc

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

od135048/2019_2020 : Supply of 10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

90.11.1.10 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

od136286/2019_2020 : SITC of D-Link (DIR-878) AC1900 MU-MIMO 1900Mbps Wi-Fi Router (Without Modem)

od136298/2019_2020 : Supply, installation, testing and commissioning of 24&quot; Monitor for CCTV

od136299/2019_2020 : SITC Of NVR 8 Channel for CCTV

Main Building Ground Floor Fire Fighting works

od254856/2019_2020 : (Kannur) Below Ground Piping :- Providing, fixing, welding joints and testing of 100 mm Dia. heavy class MS ERW Black pipes as per relevant IS 1239/3589 with special accessories tees, elbows, flanged joints, rubber insertion, nuts, bolts, washers or welded joint with flange joints on bends, including fixing the pipe with suitable flat iron strip clamps/brackets structural members dash fastener,civil breakage,making good the same etc. painting with a primer coat and two coats of postal red enamel etc. complete as required. (for wet riser system)&lt;br&gt;

od254565/2019_2020 : (Kannur)4.1P: Supplying, installation, testing and commissioning of electric driven terrace pump suitable&lt;br&gt;for automatic operation and consisting of following, complete in all respects, as required:&lt;br&gt;(Terrace Pump)&lt;br&gt;Horizontal type, multistage, centrifugal, split casing pump of cast iron body &amp; bronze&lt;br&gt;impeller with stainless steel shaft, mechanical confirming to IS : 1520&lt;br&gt;Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3&lt;br&gt;phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted&lt;br&gt;type with Class-&apos;F&apos; insulation, conforming to IS-325.M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as&lt;br&gt;required.&lt;br&gt;Suitable cement concrete foundation duly plastered and with anti vibration pads. 900lpm @ 35 m head

od254566/2019_2020 : (Kannur) 7.7: Providing, laying, testing &amp; commissioning of &apos;C&apos; class heavy duty MS pipe conforming to IS&lt;br&gt;3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets&lt;br&gt;etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with&lt;br&gt;two or more coats of synthetic enamel paint of required shade complete as required :&lt;br&gt;100mm dia pipe

od254567/2019_2020 : (Kannur(14.5) Providing, installation, testing and commissioning of non-return valve of following sizes&lt;br&gt;confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100mm dia

od254568/2019_2020 : (Kannur ) 19.1 : Supplying and fixing of fire brigade connection of cast iron body with gun metal male&lt;br&gt;instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe&lt;br&gt;connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe&lt;br&gt;

od254569/2019_2020 : (Kannur) Providing &amp; fixing 25mm Air release valve as per IS:14845 ISI Marked

od254570/2019_2020 : (Kannur) 22 : Providing &amp; fixing of pressure switch in M.S. pipe line including connection etc. as required.

od254571/2019_2020 : (Kannur) 11.5 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with&lt;br&gt;bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets&lt;br&gt;conforming to IS 13095 of following sizes as required :100mm dia

od254572/2019_2020 : (Kannur )9.2: Supplying and fixing single headed internal hydrant valve with instantaneous&lt;br&gt;Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming&lt;br&gt;to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Stainless steel

od254573/2019_2020 : (Kannur) 7.1: Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office&lt;br&gt;red, conforming to IS 884 complete with the following as required.&lt;br&gt;20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS:&lt;br&gt;12585&lt;br&gt;20 mm nominal internal dia gun metal globe valve &amp; nozzle.&lt;br&gt;Drum and brackets for fixing the equipmets on wall.&lt;br&gt;Connections from riser with 25 mm dia stop gun metal valve &amp; M.S. Pipe and socket - 30m

od163566/2019_2020 : FIRE DUCT :- Supply &amp; installing in position self glowing &quot; FIRE DUCT &quot; sign board of size 100mm x 300 mm made of luminescent safely, rigid sheet in green colour, photo luminescent rigid sheet with two each hanging chains / or fixed on wall &amp; necessarry supports to hang it on ceiling / or on wall.

od163569/2019_2020 : FIRE EXIT :- Supply &amp; installing in position self glowing &quot; FIRE EXIT &quot; sign board of size 100mm x 300 mm made of luminescent safely, rigid sheet in green colour, photo luminescent rigid sheet with two each hanging chains &amp; necessarry supports to hang it on ceiling.

od163570/2019_2020 : ESCAPE ROUTE SIGNS :- Supply &amp; installing in position self glowing &quot; EXIT &quot; sign board to guide the occupants towards the exits of size 100mm x 300 mm made of luminescent safely, rigid sheet in green colour, photo luminescent rigid sheet with two each hanging chains &amp; necessarry supports to hang it on ceiling.

od134479/2019_2020 : M.S Hose Cabinet : - Providing &amp; fixing M.S Hose cabinet door with powder coating of postal red color (of size minimum 1200mm wide, 2100mm height) made of M.S sheet 14 G with glass front door and locking arrangement to accommodate 2-hoses, one branch pipe and to accommodate F.A. hose reel in addition for internal hydrant complete as per direction of Engineer incharge.&lt;br&gt;

od134482/2019_2020 : Supply, installing, testing and commissioning of Fire Extinguisher dry chemical powder type ISI mark, 5 kg capacity with initial charger and installation brackets.Make - Safex / Warrior / Intime

od134483/2019_2020 : Providing 63mm (2&frac12; )&quot; dia 15 m long canvas hose pipe complete with stainless steel male &amp; female coupling stainless steel wire wound with the pipe The pipe shall confirm to IS. 4927. Make: ISI Approved.

od134487/2019_2020 : Providing &amp; fixing pressure gauges of not less than 100mm dia dial of pressure range 0-10 kg/cmsq complete with shut off valve duly calibrated before installation.Make:- ISI Approved.

od134489/2019_2020 : Supply and drawing of 2.5 sqmm 3 core PVC / XLPE insulated armoured control cables with copper conductors for working voltages up to and including 1100 V conforming to IS 1554 part I 1988 for PVC and IS 7098 Part I for XLPE

od133918/2019_2020 : Supply, Installation, Testing and commissioning of Over head tank (Structural Steel) with necessary Accessories (Nuts,Bolt and Support.etc) , Approved Make/Materials :- ISI Approved Materials.

90.14.28.2 : S & F Motor starters of the following ratings

od254878/2019_2020 : Providing and fixing Fire Man axe as required with Test Certificate of 20,000 volts.Make : - ISI Approved.

PINARAYI INDUSTRIAL CO OPERATIVE SOCIETY LTD

Bidder Name

PINARAYI INDUSTRIAL CO OPERATIVE SOCIETY LTD

SHAMEER M A