REPAIR TO DRAIN, FENCING, BOUNDARY WALL, REPAIR TO HARDSTANDING

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Dismantling of old barbed wire fencing complete all as specified and directed.

Dismantling of posts or struts (wood/ steel or RCC) any section including taking out embedded portion and making good disturbed natural ground complete all as specified and directed.

Demolition of cement concrete (un reinforced) of any description in any position not otherwise specifically provided for etc. complete all as specified and directed.

Dismantling chain link fencing of any description complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation mass concrete complete all as specified and directed.

M&L for brick work with fly ash bricks old size bricks in cement mortar, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified as directed.

M&L 15mm thick in CM 1:4 rendering on fair faces of brick work is to be finished even and smooth (without using extra cement) complete all as specified as directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary or concrete surfaces of wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L Providing Cement concrete 1:2:4, type C2 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified as directed.

M&L for PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) for copings on brick wall surfaces including weathering, slightly rounded or chamferred angles and throating , as directed.

M& L 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as specified

M&L for Machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed.

M&L for Machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80 mm thickness, M-40 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed.

M&L for Machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 100 mm thickness, M-50 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed.

M&L for PCC 1:2:4, type B1 (using 20mm graded aggregate) for machine pressesd precast cement concrete kerb stone including weathering, slightly rounded or chemferred angles and throating, as directed edges complete including excavavtion for kerb stone as directed.

M & L 25 mm thick PCC 1:2:4, type B0(using 12.5mm graded stone aggregate) as in floors to receive surface of tile complete all as specified and directed.

M&L 20 mm thick, screed bed or bedding layer of mortar in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L for coloured glazed chequered cement concrete 20cm x 20cm x 25cm thick With mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

S&F in repair MS steel work in tubular trusses for sign board posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240, complete all as specified as directed

S&F Welded steel wire fabric weight n exc 4 kg/sqm supplied and fixed complete to wood or steel members complete all as specified as directed

S&F in repair fiber sheets 1.5 mm thick of any colour having high tensile strength fixed with existing chain link fencing or on post with self screw and nut bolts all necessary fittings complete all as specified and directed. Note : Sheet colour shall be approved by GE

S&F in repair Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

M&L for cement concrete 1:4:8, type (using 40mm graded stone aggregate) in foundation and filling around fencing post complete all as spd & directed. Note:-Deduction for the portion of fencing post / strut embeded in concrete shall be made

S&F M S Posts and struts in fencing (any size of angle) mm including cutting tops to shapes as directed including driling holes for bolting of MS flat iron in horizontal, vertical & diagnal faces of each pannel to be intertwined with Chain link fencing, and fixed to posts with MS nut bolts and washers ,wind ties for sign board posts and struts, and similar work confirming to Fe 290 Gde E-165 complete all as specified as directed

Fixing only chain link M S galvanised fencing (IS-272) mesh as required but weight of mesh not exc 4.0 kg/sqm complete all as specified and directed

Supply only chain link MS galvanised fencing any size or type complete all as specified as directed

M&L for PCC 1:2:4, type B-2 (using 20 mm graded stone aggregrate) mass concrete as in embadded 15 cm below, below up to 200 mm from above GL (from work paid seperately ) for fixing chain link fencing complete all as specified as directed.

Formwork to sides of Rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified as directed.

Mild steel screw bots (machine made ) with hexagonal or square heads at one end and screwed the other each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm but not exc 15 cm and 15mm dia complete all as specified as directed

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts including securing of typing at crossings with provision of galvanised mild steel wire staple or steel pin as directed (each line of wire to be measured) complete all as specified as directed

S&F mild steel grills framed work as such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways, m s railings framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 all as specified and directed.

S & F 1.25 mm thick Mild steel, plain black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete including cutting out of existing sheet if required all as spd as directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing complete FE 290 Gde E-165

M&L for cement concrete M-20, type A 2, 20 mm graded coarse aggregate (nominal mix) as in floor, concrete surfaces finished fair even laid in bays n.exc 2 m in length & joints filled with bitumen mastic 1:3 complete all as specified and directed.

M&L for precast reinforced cement concrete M-30 (20 mm graded aggregates) as in drain cover slabs supported on wall (width of drain n exc 3.0 mtr) used 10mm,12mm or 16mm bar complete all as specified (reinforcement to be measured & paid under respective items).

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat white wash complete all as specified and directed.

Preparation of new steel surfaces exc 10 cm width or girth and applying two coats of syntetic enamel paint over one coat of red oxide of zinc chrome primer complete all as spd &directed .

M/S SAJJAD HUSSAIN CONTRACTOR

M/S ABHISHEK ENTERPRISES

M/S Quality Constructions

DIKSHA CONSTRUCTION CO

Jain construction co