PROVISION OF DESERT COOLER STAND IN SMQs, SPECIAL REPAIR TO OMQs/SMQs AND PLINTH FOR PUTTING AIRCRAFT AT STN HQ BUILDING AT DARJIPURA AF STATION BARODA

Amount

M&L framed brackets of angle/square pipe/round pipe/channel or tees with web and flange cut to shape,drilled and counter sunk for screw incl binding and welding angle as necessary gusset plates,riveting etc confirming Fe-410or Fe-310 complete all as specified and directed.

S&F Anchor fastener 15 cm long and 10 mm dia incuding one nut and washer fixing for MS cooler stand in wall including drilling and fixing complete all as specified and as directed.

Surface excavation in any type of soil n.exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed.

M&L for hardcore of broken stone or boulder of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase complete all as specified and directed.

M&L Sand filling under floors as cushi-oning including watering and consolidation complete all as specified and directed.

M& L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment including 40mm thick sand bedding complete all as specified and directed

Pre-cast cement concrete TypeB1 1:2:4 (20mm graded aggregate) block masonry with solid blocks, exc. 10cm in width and setting in mortar1:4 complete

Removing excavated surplus soil to a distance not exc 50m and depositing where directed at a level n.exc 1.5m above the starting points complete all as specified and directed.

Excavation in trenches not exc.1.50m wide and not exc 1.5m deep for foundation extc etc and getting out in soft/loose soil as directed.

M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) Type B1 1:2:4 (20mm graded aggregate) in foundations, footing complete all as specified and directed.

Use & waste of form work for rough finished flat surfaces such as side of concrete of foundation, footings, bases of columns and similar work vertical or to batter complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed, not less than 0.9mm dia complete all as specified and directed.

M & L for TMT bars 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed, not less than 0.9mm dia complete all as specified and directed.

Returning , filling in, including spreading leveling, watering and well ramming in layers n.exc 25cm each layer in soil complete all as specified and directed.

M&L rendering 15mm thick cement plaster on fair faces of concrete surfaces in CM 1:4 complete all as specified and directed.

S&F of mild steel work such as grills, gratings, MS sheet ets., with ends of bars, shouldered and/ or rivetted, or forged into spikes; framed guard bars, barred iron , etc complete all as specified and directed.

Painting steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described, including preparation of surfaces, primig with Red Oxide, Zinc Chrome and two coats of synthetic enamel (Ordinary tint) complete all as specified and directed.

Taking down chowkats or frame exc 1.5 Sqm and n exc 4 Sqm each (without taking off shutter from the fram) complete all as specified and directed.

Taking down chowkats or frame n exc 1.5 Sqm each (without taking off shutter from the fram) complete all as specified and directed.

Taking down shutter only of any description n exc 1Sqm and removing complete all as specified and directed.

Taking down shutter only of any description exc 1Sqm n. exc 2Sqm and removingcomplete all as specified and directed.

S&F Powder coated aluminium work of for door, windows and ventilators and and partition wall with one or more rebates fixed in position as per manufacturer's instruction including necessary joining cleat, glazing clips, rubber packing, beading ,plaster work on edges during fixing (if required) etc complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with stainless steel wire staples complete all as specified and directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permice complete all as specified and directed.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc complete all as specified and directed.

All as per item No 28.00 above but on vertical surfaces/skirting etc complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 SQM but not exceeding 0.11 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls complete all as specified and directed.

Demolition of stone slabs and tiles of any description, laid bedded and pointed in any mortar complete all as specified and directed.

M&L 18-20mm thick granite slab with fully rounded edges on front face fixed with adhesive or laid in neat cement slurry over 10mm thick screed bed in CM 1:6 including cutting space for sink & gas pipe hole etc complete all as specified and directed.

Taking down cement plaster of walls or roof ceiling of any description including raking out joints, hacking for key, scrubing down with water etc including cleaning site time to time without accumulating the debris in and around the working place complete all as specified and directed.

M & L for 10 mm thick rendering in CM 1:6 on concrete surfaces / fair faces of brick masonary wall, finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in CM 1:4 on concrete surfaces / fair faces of brick masonary wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick on concrete surface of ceiling CM 1:3 finishing the surface fair and even complete all as specified and directed.

M&L for complete removal of existing treatment by scraping down thoroughly, rubbing down and washing with water to the entire satisfaction of Engineer-in-Charge and applying two coats of exterior ACRYLIC Emulshion paint (Colour or shade as approved by GE) over and including a coat of primer on walls as per manufacturers instruction including necessary steel scafolding upto 4th storey complete including cleaning window glasses, joinery, electric fittings, wiring etc of drops and splashes and cleaning premise clean and tidy complete all as specified and directed

M&L for preparation of old decorated surfaces of walls including cornices , pilasters by brooming down or steel wire brushing , scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of oil bound emulsion distemper on wall surfaces and to be applied only by the authorised applicater of manufacturers (as approved by GE) including cleaning window glasses, joinery, electric fittings, wiring etc of drops and splashes and cleaning premises clean and tidy complete all as specified and directed

M&L preparation of old surfaces and applying Cement putting on wall/ceiling finished complete all as specified and directed.

M&L for preparation of old decorated surfaces plastered or unplastered on walls including cornices pilasters by brooming down or steel wire brushing, scraping down, smoke shoot, moulds, mors and efforescent salts and treating oil and greasy spots and applying one coat of white wash on walls upto 4th floor complete all as specified and directed.

All as per item no. 43.00 above but one coat of white wash on ceiling complete all as specified and directed.

Preparation of old painted surfaces of steel and iron surfaces over 10cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L filling surface cracks not exc. 5mm to 7mm wide with "Dr Fixit" cracks X power or equivalent polymer molified cracks filler all as per manufacturer's instructions complete all as specified and directed

M&L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash on walls upto 4th floor including cleaning window glasses, joinery, electric fittings, wiring etc of drops and splashes and cleaning premises clean and tidy complete all as specified and directed

M&L for preparation of new surfaces of wall and applying two coat of oil bound distemper all as specified (any tint shade as approved by GE) complete all as specified and directed.

M&L 35mm thick 2nd class hardwood glazed and skeleton shutter open rebeted and prepared to receive glass gauze etc (without shash bar ) edges of framing plain chamfered or rounded filled with cut and mitered beads for securing, glass etc size of member of shutter as per specified in SSR Part-I section 8,clause 8.24(a) supplyed and fitted to chowkats complete all as specified and directed.

M&L Factory made flush shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in shutter complete all as specified and directed.

M&L Factory made flush shutters 25mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in CB shutter complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications & drawings complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawingspecification and drawing complete all as specified and directed.

S&F 75mm long SS butt hinges and fixed to frame with scrwewd or welding complete all as specified and directed.

S&F for 100mm long butt hinges, medium weight , cold rolled mild steel and fixed complete all as specified and directed.

S&F for 200mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and directed.

All as per item No 56.00 above but 150mm long complete all as specified and directed.

S&F aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruted section or cast aluminium alloy and fixed length of bolt 300mm complete all as specified and directed.

S&F for 150mm long aluminium handle cast type anodized complete all as specified and directed.

S&F Hasp and staple,safety type aluminium anodized including bolt to hinge plate and fixed with screws 150 mm size complete all as specified and directed.

S&F door stopper of 150 mm size (ISI Marked) aluminum alloy body and tongue double legged anodized with hard draw steel spring over all length of cover plate fixed in floor complete all as specified and directed.

M&L Preparation of new wooden surface of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F in repair 25 mm dia curtain drapery rod decorative type cut to length and fixed complete all as specified and directed.

S&F in repair bracket suitable for 25mm dia curtain rod with steel screw/ wooden screw complete all as specified and directed.

Taking up or down steel tubing pipe and connections 15mm bore complete all as specified and directed.

S&F 15mm dia tubes ‘Medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed.

Dismantling water tanks exc 500 but n.exc 1000 Litres capacity.1000 Litres capacity complete all as specified and directed.

S&F rotational moulded water storage tank 1000 Ltr capacity double layer (cylindrical/vertical with closed top) hoisted and fixed in position complete all as specified as directed.

S&F 20 mm ball brass valves,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repair vitreous china wash hand basin, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and including flush pipe) including connection to trap and flushing pipe etc and making good the floor as per existing surface complete all as specified and as directed.

S&F in repair 10 litres capacity PVC valveless symphonic action type, flushing cistern, low level, white, with inlet, ball valve float handle including brackets complete all as specified and directed.

S&F 32mm brass chromium plated waste coupling for wash hand basin complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium platedscrewed down highpressure, with orwithout lettered 'Hot' or 'Cold' withlong screwedshanks and fly-nuts,screwed for iron pipe and fixed to 15mm bore pipe complete all as specified and directed.

S & F in repair Bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm bore pipe complete all as specified and directed.

S&F in repair Stop valves, cast copper alloy,screwed down,high pressure,with crutch orbutterfly handle,screwed bothends for iron pipe or fo runions and fixed to15mm bore pipe complete all as specified and directed.

S&Fin repair 32mm PVC waste pipe for wash hand basin., 600mm long complete all as specified and directed.

S&F in repair Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed.

S & F in repairs Soap dish PTMT, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Dismantaling of unreinforcement lime concrete/cement concrete in padding to roof slab and removing the rubbish off premises complete all as specified and directed.

M&L for providing cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate laid to slope 1:30 in padding for WPT over roof slab complete all as specified and directed.

M&L for providing cement concrete type B 0, 1:2:4 using 12.5mm graded aggregate in cover fillet of 75 mm radius at junction of roof slab and parapet wall etc complete all as specified and directed.

Removing of existing unserviceable water proofing treatment taking down cement plaster etc, of any description and cleaning of top surface of cement concrete flushing out junction of parapet walls & washing down with water to remove all dirt etc including preparation of surfaces to receive new treatment and removing the rubbish off premises complete all as specified and directed.

M&L for applying cold bituminous primer @ 0.30 ltr/Sqm conforming to IS 3384 and laying APP polymer modified fiber glass reinforced membrane 3mm thick 3.5Kg/Sqm (modified bituminous water proofing membrane) with plain finish with ploystere base reinforcement sealing all the over laps of 75 mm in length side and 100 mm on the width side of membrane by torching the same all as per manufacturer instruction including one coat of butuminous aluminum paint @ 0.10 ltr/sqm over membrane Complete all as specified and directed.

Note:- Rate quoted deemed to be inclusive of cleaning of surface to be treated properly to receve the primer complete all as specified and directed.

APP membrane treatment shall be done firstly at corners and junction of parapet wall 30cm on verticle position and 30cm on horizontal position shall be done with proper attention and work carried out by authorised applicator only.Main portion of roof treatment shall be commenced only on completion of corners/edges/junctions.

APP membrane shall be taken upto outside of the parapet wall to an extent of 150mm minimum.

Ensure while laying the treatment no bulging on surface/voids shall be found and proper care/attention be given for the treatment.

Codntractor shall produce the certificate from the manufacture for the authorised applicator before commencement of work.

M&L10mm thick screed bed in CM 1:4 mixed with WPT 3% by weight of cement all as specified and as directyed

Supply only intergral water proofing compound.

M&L removing the tank over roof and re-fixing in the same position (or lowering if requried) including cleaning complete all as specified and directed. Note:- rate quoted shall deemed to be inclusive of making good the existing disturbed surface complete all as specified and directed.

Demolition of brick or stone walling built in cement mortor incl all quoins, archs, pillars, etc complete all as specified and directed.

M&L Brick work sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed

M&L for treatment to sunken portion (including necessary dismantling of tiles and PCC along with required PCC at site of mix 1:2:4 type B1 using 20mm graded aggregate of required thickness) with 10mm thck plaster in CM 1:4 with WPC Liq complast 421 and applying one coat each of Nitroproof 100 and Nitroproof 120 on plastered surface. Rendering again 10 tck plast in CM 1:4 mixed with complas 421 in sunken portion of WC and CI pipe joint shall be filled including filling of lean concrete 1:5:10 even using 20mm graded aggregate complete all as specified and directed.

Dismantling of CI or reinforced concrete drain pipes 75/100mm internal dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F CI soil waste vent and rain water pipe 75 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed.

S&F CI soil waste vent and rain water pipe 100 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed.

S&F in repair cast iron floor trap 75 mm outlet dia with grating including jointing to waste pipe fixed in cement concrete type B1, (1:2:4) complete all as specified and directed.

Dismantling structural steel work including doors, gates, grill but excluding framed truss etc. all as specified and as directed.

M&L Framed work ( Fe 290 gde E 165) as in doors or gates/Grills of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and uides) and hanging; also fastening and fixing complete all as specified and as directed

SHREE KHODIYAR TRADERS

Chanda Construction Co.

M/S TANUSHREE CONSTRUCTION COMPANY

M/s GANGA CONSTRUCTION