Design, Engineering, Supply, Installation, Testing and commissioning of Non Clog type Centrifugal Pump Set for effluent with accessories and allied Electro-Mechanical and Instrumentation and SCADA work at Vilayat Pumping Station.

Name of Work: Design, Engineering, Supply, Installation, Testing and commissioning of

"Non Clog type Centrifugal Pump Set for effluent" with accessories and

allied Electro-Mechanical and Instrumentation and SCADA work at

Vilayat Pumping Station.

Item Description Qty Unit Rate W/O Amount W/O

1 MECHANICAL WORKS: 2 Set 7,99,518.02

SUBMERSIBLE CENTRIFUGAL NON CLOG

Supply, installation, testing &

commissioning of Effluent submersible,

non clog type suitable for working on

three phase, 50 Hz ± 3%, 415 V ± 10%, AC

supply, 1450 RPM synchronous speed

with 3 core flat copper cable from pump

to starter panel with cable end

terminations, all supports, clamps, pipe

fittings along with mechanical seal,

bearing bush, strainer etc. complete set &

following M.O.C: Casing: CI, Impeller: SS

CF8M, Wearing ring & Bearing bush:

Bronze, TC mechanical seal, CS / SS

bearing, SS shaft with sleeve, SS strainer

& MS motor body

Pump Capacity: 313 m3 / hr.

Motor Rating: 45 kW min. (or higher

rating as per pump manufacturer

recommendation)

Starting method: DOL / SD / VFD

(or higher rating as per pump

manufacturer recommendation)Selection

of motor kw rating if not available in this

rating, next higher rating will be consider

2 Design, Engineering, procurement, 2 Nos. 37,962.87

Installation, Testing and commissioning

of required size double flanged Dual

Plate Check Valve (DPCV) - (PN 1.6) -

mm dia (At Pump Discharge) Flanged

Dual Plate Check Valve (NRV) conforming

to API 594 / 598 PN 1.6 with Cast Steel

body, withSS 410 hinge ring and wearing

ring of CF8 all necessary hardwares,

complete as per data-sheet &

Signature of Contractor Executive Engineer (M&E)

specification. Size : 300 mm dia( PN 1.6)

flanges machined faced and drilled to IS :

1538 / 1976 Part-IV/VI. Hydraulic tests

certificate & certificate of material of

construction of parts shall be submitted

before despatch of valves as per design

with required acessories, erection

hardware, necessary mounting supports

etc. complete. 300 mm dia for various

3 Supply, installation, testing & 2 Nos 10,908.00

commissioning of flange ends Expansion

Bellow as per EJMA standards of overall

length of minimum 300 mm, designed for

15 mm axial compression and 5 mm axial

extension with tie rods etc. of following

MOC & pressure ratings.MOC: Bellows: SA

240 Gr. 304; Internal Sleeve: SA 240 Gr.

304; Weldends: IS 2062 Gr. B; Flanges: IS

2062 Gr. B (Drilling as per IS 1538 / IS

6392 ) & Limit Rods & Nuts: CS - IS

PN Rating 1.6, 300 mm Dia.

4 SITC of Cast Steel D/F Electric Actuator 2 Nos 9,30,800.00

operated Sluice Valve of following size as

per API-600/598,Class 150 with Electric

Actuator with integral starter & IP-68

enclosure, body, bonnet and wedge of

Cat Steel Gr. WCB with Body & Seat ring

of ASTM A 216 Gr CF8M, spindle of SS

410, flanges drilled to ANSI B 16.5 of

following diameter along with all other

necessary hot dipped galvanised

hardwares, bolts, nuts & washers, gaskets

including all taxes, insurance,

transportation, freight charges,

Inspection Charges, loading unloading,

conveyance to pump house, stacking,

security with required plain cement

concrete (PCC) support for Valves etc.

within pump house for fixing valve etc.

complete as per Specification and IS.

Size : Dia. 300 mm

5 Provide and supply CI Temper Proof Air 1 Nos 49,161.75

Valves with SS 304 Float Gun Metal

Nozzle of approved make and quality of

following dia of 1.6 PN rating given rate

including all taxes, insurance,

transportation, freight charges,

inspection charges, loading and unloading

conveyance to departmental store/site

Etc.with Isolating Suice Valve.

Size : 300 mm NB

6 SITC of suitable size of above pipes of 100 Kg 58.58

flanged end type fabricated DI/CI Specials

like tee, bend, duck foot bend, tapper,

Signature of Contractor Executive Engineer (M&E)

distance pipe piece, blank flange,

dismentling joint, bolts, nuts, washers,

rubber packing etc.nut bolts etc for

delivery header, rising main and suitable

for above pumps as per actual site

conditions & requirement qty. of specials

mentioned as per deisng requirement

with required acessories, erection

hardware, necessary mounting supports

300 mm dia- Drilled

7 Supplying and fixing Steel chequered 20 Sq. Mtr 5,780.23

plates having 12 mm thickness, duly

painted with two coats of black Japan

colour. (Average Wt 200.3 kg / Sq.Mtr.)

8 Supply, cutting, welding, installation, 8 Rmt 1,235.23

connection with main header, testing and

commissioning Making of Flanged joint to

flanged DI/CI pipes of all classes/ Special

etc. including all taxes, insurance,

transportation, freight charges,

inspection charges, loading and unloading

conveyance to departmental store/site

Size: 300 mm dia.

9 Single Girder EOT CraneSupply, 1 Set 5,11,312.50

installation, testing & commissioning

single girder type fully electrically

operated EOT crane with electrically

operated hoist, class II duty, geared

travelling trolley with seven meter lift

complete with long travel rail track (40

mm sq. bar), moving or cross girder, all

three motions electrically operated by

suitable rating motor IP 54, control panel

& down pendant control block, brake,

safety device, cables form motor to

starter panel & other required

accessories & tested as per IS

Specifications.Capacity- 2 T, Span- 6-9

Mtr, Long Travel- 12 Mtr, Lift 6-10 Mtr

10 SITC Chain Pulley block of 2 ton capacity, 1 Nos 17,574.00

lift as per site condition with gantry

girder, erection hardware, necessary

mounting supports etc complete.make as

11 DEWATERING PUMP 2 Nos 1,47,811.48

Supply, erection, testing and

commissioning of non clog submersible

Drain Pump with CI casing & CF8M

impeller,including necessary accessories

and hardwares, etc., 15m cable for motor

to starter panel, suitable for 3Phase,

V, 50 Hz AC supply and min. 2.2 kW

motor, Switch-Starter panel with suitable

Signature of Contractor Executive Engineer (M&E)

inter lock for winding protection, min.

m long required size cable to supply

power to control panel from nearby

power source, moisture controlar along

with level switches for dry run protection

for auto stop facilities, cable termination

junction box of required terminal size,

supporting arrangement for pump and

other required accessories,

Capacity : 10 - 15 m3 / hr.

( to be installed in dry well drain pit.)

12 PORTABLE DEWATERING PUMP / 1 Nos 1,94,690.63

Supply and testing of Submersible non

clog Portable Dewatering Pumpset with

C.I. casing & CF8M impeller, 25 m flexible

PVC delivery hose pipe of pump delivery

size, rated for 6.0 kg / cm2 presure,

mtr SS lifting chain, 20m pair of cable for

motor to starter panel, suitable for

3Phase, 415 V, 50 Hz AC supply and min.

5.5 kW motor, min. 10 m long required

size cable to supply power to control

panel from nearby power source, Switch-

Starter panel with suitable inter lock for

winding protection, moisture controlar &

dry run protection auto stop facilities,

SS/CI pump stool and other required

accessories for wet well.

Capacity : 50 m3 / hr.

Motor Rating: Mini. 5.5 kw

13 MISCELLANEOUS: 800 Kg 65.49

Providing, Supply of Structure Steel at

site of work with freight, loading,

unloading carting, etc. including all taxes

and duties complete such as joints,

channels, angles, plates, iron rails,

ISA/ISMC/ISMB/MS flat, plate (below

10mm thickness) etc. required for

support structure of Elecrto-Mechanical

equipments etc. for support on floor /

wall / beam / brackets etc. as per tender

14 Labour Charges for lowering, laying, 1 MT 11,478.65

Fixing with fabrication various size

section of MS such as joints, channels,

angles, plates, iron rails,

ISA/ISMC/ISMB/MS flat, plate etc

Complete with two coats of red oxide and

two coats of approved colour shade of

epoxy paint as per relevant IS and as per

Signature of Contractor Executive Engineer (M&E)

15 Tools as per Annexure (M) and as 1 Lot 2,50,000.00

recommanded by manufacturer.

16 ELECTRICAL WORK 1 Nos 37,601.29

TPN MCCB (For LT Service Obtaining

SITC of 200 A TPN microprocessor MCCB

with O/L, S/C & E/F protection with

Extended rotary handle, Terminal

spreader, Auxiliary change over & Trip

contact, with Outdoor Enclosure with

canopy 2mm thick , Single/double door &

Wall mounted/ stand mounted as per site

requirement (with incoming & outgoing

cable entry at bottom )with Cable end

boxes with RYB indicating lamp, Digital

voltmeter, VSS, ON,OFF & Trip indicating

lamp etc as per Power supply company

requirements & location. Including all

civil works for fixing of panel on wall.

(Wall mounted at Location as per PSC

17 LV APFC PANEL 1 Set 1,89,950.70

Supply, installaton, testing &

commissioning LV APFC panel consisting

of required capacitor banks for

continuous duty to improve P.F. 0.85 to

0.99 in required steps enclosed in dust &

vermin proof compartment, indoor type,

fabricated from CRCA sheet steel with

minimum thickness of 3 mm for base

frame / channel / gland plates, 2.0 mm

for load bearing members / doors &

mm for internal partitions, minimum

degree of protection - IP 42, busbar

chamber, required size of Al bus bar /

terminals, minimum 10 stage APFC relay,

metering, indicating lamps, push buttons

complete as per IS: 16636-2017 with

latest ammendment & detailed technical

specification and

data sheet as under

Above 50 & up to 100 KVAR: APFC panel

consisting following items.

a) 250 A, 50 kA for 1sec. TP, TM based

MCCB with spreader terminals & rotary

b) 0-250 A range analogue ammeter of

x 96 mm size with selector switch

c) 3nos. 250 / 5A, 10 VA CL-1.0 cast resin

type current transformer

d) Suitable rating of MCCB / MCB &

Contactors for each capacitor bank

e) Suitable rating APP type capacitor

banks (vacuum impregnated with non-

Signature of Contractor Executive Engineer (M&E)

PCB / non toxic oil, internally delta

connected with built in internal fuses

complete with discharge resistances &

terminal cover) of approved make in

required steps with well suited detuned

reactor is placed in series with each

capacitor step. ( e.g. 100 KVAR capacity

will be provided in steps of 2 nos x

KVAR, 2 nos x 10KVAR, 2 nos x 15 KVAR

& 2 nos x 20 KVAR)

f) Enclosre dimensions: 2100 (H) x

18 Design, Supply, Installation, Testing and 1 Nos 3,44,504.94

Commissioning of Power cum Motor

Control Centre of 200 A, 415, TPN, Power

Cum Motor Control Centre (PCC) cubical

having depth not less than 750 mm

throghout the required length &

detachable, fabricated from 2 mm CRCA

sheet steel, free standing, floor mounted,

compartmentalized, extensible, dust and

vermin proof enclosure, duly painted

provided with required rating switch

gears and shall be complete with (a)

required size of TPN Electrolyte 100 A

Copper bus bar having cross section not

less than 1.6 Amp per 1.0 Sq. MM, (b)

Nos. - 100 Amp capacity of 4 pole-

microproccessor based MCCB with

computer interface (2 Nos. for incomer +

1 No. as Bus Coupler) (c) 3 Nos. -

Amp capacity of 4 pole - microproccessor

based MCCB computer interface - All

release of all MCCB should have in built

power meter/ analyser having, 3 phase,

V, KW, I, KVA, KVAh, KVArh, PF,

Frequency, harmonic analysis up to 30th

harmonic and last ten faults history.with

computer interface facility and all other

required protection etc., complete. ,The

PCC shall be supplied as per detailed

specifications & single line diagram (SLD)

complete and the instruction of Engineer

19 Microprocessor Based LV Variable 2 Nos 1,11,862.55

Frequency Drive

Suppl, installation, testing &

commissioning of 415 V Fully automatic

microprocessor based Variable

Frequency drive for pump control

application as per general specification as

The VFD unit shall have modular

construction, 6 Pulse Bridge rectifier,

speed control by means of sensorless

Signature of Contractor Executive Engineer (M&E)

vector control (open loop), high torque at

low frequencies, locking at high and low

frequency settings, In-built PID control,

frequency accuracy of ± 0.1 % (min),

frequency resolution of ± 0.1 Hz (min),

protections against; a) overload (motor

and drive), b) short circuit, c) ground

fault, d) input / output phase loss (open

circuit), e) stalling, f) input / output

undervoltage (momentary power loss

restart), g) input / output overvoltage, h)

over-frequency, i) Input surge, j) over

temperature of heatsink, k) loss of remote

speed signal etc. The VFD shall also have

user friendly programming software & it

shall be capable of at least two level

parameter setting with password lock for

critical parameters, programming for

I/Os, speed search function, copy

parameters (upload / download) to other

identical unit, tuning to energy saving

mode (maximum efficiency), event / fault

recording (last 5 faults in non-volatile

memory) & RS 485 communication port

(MODBUS RTU protocol) with required

software. for 55 Kw

20 SITC of Lighting Distribution Board (LDB) 2 Nos. 20,998.91

SITC of 3 Phase 4 Wire 4P, double door

Prewired LDB each for Indoor Lighting &

Outdoor Lighting Suitable to house :

Incoming: 200A FP, ELMCB (30mA)

Outgoing: 63A SP MCB (9 nos.) & 63A SP

21 3 Phase 4 Wire TPN, 8 way Pre-wired- 1 No. 8,876.89

aux. Load for Auxiliary accessories Load

power supply (For 1no.EOT Crane at P.H.,

1no.WR-DB at P.H.maintenance floor,

1no. WR-DB at P.H Pump Floor, 1no. WR-

DB at LT Room, 1 no. WR-DB at Inlet

chamber & rest spare) Incoming: 20A 4P,

MCB 'C' Curve Outgoing: 8 nos. 20A 4P

22 SITC of LCS pushbutton station ON & OFF 4 Nos 2,384.61

(E-stop) set complete with Enclosure,

necessary mounting/ fixing arrangement

on wall / pipe support etc. to be installed

near motors for remote operation, etc. as

per IS and specifications. (including

structural steel) (For 4 nos. for Pump )

23 SITC of Local Control Station with 4 Nos 2,736.09

pendant type Open_Stop_Close

pushbutton set and with Open, Close, Trip

& Local / Remote Indicating Lamps

complete with Enclosure, necessary

Signature of Contractor Executive Engineer (M&E)

mounting/ fixing arrangement on wall /

pipe support etc. to be installed near

motors for remote operation, etc. as per

IS and specifications (including structural

24 LOW VOLTAGE (LT) CABLES 180 Mtr 135.34

Supply, laying, testing and commissioning

of 1.1 kV, A2XFY(X)/2XWY(X) XLPE

insulated (IS 7098) AL stranded

conductor, Extruded innersheath cables

as per specification & IS. The cable when

laid outside the building shall be laid

underground in trench with brick & sand

protection/in DWC pipes as per specified

method and shall be laid in prepared

trench/ on cable tray when laid inside

SITC of 3.5C x 16 sq. mm. A2XFY(X) Cable

25 3C x 16 sq. mm. A2XFY Cable 180 Mtr 90.90

26 4C x 10 sq. mm. A2XFY Cable 120 Mtr 97.97

27 4C x 16 sq. mm. A2XFY(X) Cable 120 Mtr 109.08

28 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable 50 Mtr 70.70

29 5C x 1.5 sq.mm. 2XWY(X) Cable 50 Mtr 150.00

30 12C x 1.5 sq.mm. 2XWY(X) Cable 50 Mtr 320.00

31 2C x 2.5 sq. mm. 2XWY(X) Cable 50 Mtr 49.00

32 Single core 95 sq. mm. PVC insulated 20 Mtr 919.10

circular unsheathed copper conductor

flexible Cable (For Power supply

Metering Panel to I/c MCCB Unit)

33 CABLE END TERMINATION AND 32 Nos 161.60

SITC of Double compression Ni-Plated

brass cable glands and crimping type

Bimetallic lugs / sockets with necessary

tools and equipments as specified in

specifications and IS. The glands and

lugs / sockets shall be suitable for cable

size and type mentioned below & as per

specifications.

1) Earthing the glands and armouring

with earthing clamp and jumper and also

connecting to common earth bar.

2) The job also includes, if necessary,

supply & fixing of extension busbar of

same material on MCCB or panel board

terminal / connector to connect more

Signature of Contractor Executive Engineer (M&E)

than one no. of parallel cables or to

connect higher size cable to lower size

unit. The job also includes earthing the

glands and armour of the cable with

common earth bar or flexible copper

mesh.(Cable termination qty. shall be as

per site requirement)

3.5C x 16 sq. mm. A2XFY(X) Cable

34 Do as Above 3C x 16 sq. mm. A2XFY Cable 32 Nos 158.57

35 Do as Above 4C x 10 sq. mm. A2XFY (X) 32 Nos 129.28

36 Do as Above 4C x 16 sq. mm. A2XFY(X) 32 Nos 163.62

37 Do as Above 4C x 2.5 sq. mm. 20 Nos 93.93

2XWY/2XFY(X) Cable

38 Do as Above 5C x 1.5 sq.mm. 2XWY(X) 10 Nos 128.00

39 Do as Above 12C x 1.5 sq.mm. 2XWY(X) 10 Nos 218.00

40 Do as Above 2C x 2.5 sq. mm. 2XWY(X) 10 Nos 49.00

41 Single core 95 sq. mm. PVC insulated 10 Nos 213.11

circular unsheathed copper conductor

flexible Cable (For Power supply

Metering Panel to I/c MCCB Unit)

42 CABLE TRAY 80 Mtr 391.88

SITC of G.I. (Hot dip galvanised ) Ladder

type medium duty (2mm thick) Cable

Tray with necessary bends, tees,

reducers, covers and clamps for fixing. All

material shall be Hot dip galvanised as

per Specification. And including all

accessories. 300 x 75 mm - Ladder type

43 150 x 50 mm - Ladder type 200 Mtr 339.36

44 Cable Trench, Laying & Installation of 80 Mtr 55.55

Cable: Making cable trench in soft soil of

suitable width of 90cms deep for laying

cable, Sand cushioning and brick

protection on sides and on top all over

the run and back filling the same and

making the surface as normal ground as

per IS & Specification. (For laying of LT

cable in ground)

45 CHEMICAL EARTHING SYSTEM 4 Set 10,593.89

SITC of Maintenance free chemical

earthing (copper) with earthpit of

minimum bore size dia. 225mm Safe

Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS-3043:1987

/Tech spec. made of corrosion free Pipes

having Outer pipe dia of 48 mm having

Signature of Contractor Executive Engineer (M&E)

250 Micron copper plating, Inner

corrosion free Hot dip galvanised (80 to

100 micron) pipe dia of 26 mm with

copper flat strip type connection

terminal 14mm dia with constant ohmic

value surrounded by highly conductive

corrosion resistant chemical compound

with high charge dissipation suitable for

electrical installation & of 3Mtr. length of

Pipe with two nos. 25Kg. bag of Back

filling compound.. (2nos for PLC earthing,

2nos for DG neutral earthing)

NOTE: Earthing Resistance value & date

shall be painted on the chamber cover.

46 SITC of Maintenance free chemical 6 Set 7,095.25

earthing with earthpit of minimum bore

size dia. 225mm Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per

IS-3043:1987 /Tech spec. made of

corrosion free Hot dip Galvanised (min

150 Microns) Pipes having Outer pipe

dia of 76 mm , Inner corrosion free Hot

dip galvanised (80 to 100 micron) pipe

dia of 26 mm with copper flat strip type

connection terminal 14mm dia with

constant ohmic value surrounded by

highly conductive corrosion resistant

chemical compound with high charge

dissipation suitable for electrical

installation & 3Mtr. length of Pipe with

two nos. 25Kg. bag of Back filling

NOTE: Earthing Resistance value & date

shall be painted on the chamber cover.

47 SITC of pipe type earthing having 150 6 Nos 368.65

cms long and 2.5cms dia. Galvanised iron

pipe with coupling and buch buried in

specially prepared earth pit complete

with necessary 8 SWG earth wire

48 SITC of 50mm(w) x 6mm(T) etc. sizes as 276 Kg 77.77

required, HOT dip galvanized GI Strip

including supply & fixing using GI

spacers, saddles when laid inside the

building and inclusive of excavation &

refilling of earth when laid outside the

building & interconnection with earth pit

& all electro-mechanical equipments.

(50X6 G.I Strip wt.2.3 kg/m,

49 Supply, laying and erection of 25mm(w) x 60 Kg 77.77

3mm(T) etc. sizes as required, HOT dip

galvanized GI Strip including supply &

fixing using GI spacers, saddles when laid

inside the building and inclusive of

excavation & refilling of earth when laid

Signature of Contractor Executive Engineer (M&E)

outside the building & interconnection

with earth pit & all electro-mechanical

equipments. (25X3 G.I Strip, 0.6 Kg/m,

50 Supply, laying and erection of 40mm(w) x 38 Kg 794.87

6mm(T) etc. sizes Copper Strip including

supply & fixing of bolts, saddles when laid

inside the building and inclusive of

excavation & refilling of earth when laid

outside the building & interconnection

with earth pit & Tr. neutral. (40X6 Cu.

Strip, 1.88 Kg/m, 1.88 x 20mtr.=38Kg.)

Copper Bolt,Nuts ,Washers shall be used

for Connecting Earth electrode to

individual eqp. Bitumen shall be used at

the place of joint/welding.

51 Supply, laying and erection of 25mm(w) x 15 Kg 794.87

3mm(T) etc. sizes Copper Strip including

supply & fixing of bolts, saddles when laid

inside the building and inclusive of

excavation & refilling of earth when laid

outside the building & interconnection

with earth pit & PLC panel. (25 X3 Cu.

Strip, 0.761 Kg/m, 0.761 x

20mtr.=15.22Kg.)

Copper Bolt,Nuts ,Washers shall be used

for Connecting Earth electrode to

individual eqp. Bitumen shall be used at

the place of joint/welding. (PLC Panel

52 SITC of HOT Dip Galvanized iron strip 10 Kg 77.77

wire 8 SWG (For LDB, LCS, etc.)

(8 SWG G.I Strip, 0.103 Kg/m, 0.103 x

53 INTERNAL WIRING 150 Mtr 82.82

SITC of Mains & outlet points wiring with

1.1 kV grade FRLS PVC insulated ISI

marked flexible stranded copper

conductor wires with medium class min.

25mm. dia. Electrical grade PVC pipe and

accessories to be erected concealed in /

to be run on surface / wall / ceiling with

following sizes as mentioned below. The

unit rate wirings shall be with connector,

PVC junction box, wires, holder, ceiling

rose, angle holder, switch, sockets, switch

board, brass chromium / cadmium plated

machine screws, phase and neutral wires,

green Earth continuity wires etc. as

required to complete wiring from LDB

panel to the final outlet termination

points. The wiring shall be as per

IS:732, IS:4648 and as per tender

specification / IS.

(a) SITC of Mains wiring with 3 wire

Signature of Contractor Executive Engineer (M&E)

54 SITC of Mains wiring with 3 wire 2.5 100 Mtr 102.01

sq.mm as per tender specification & IS.

55 SITC of Mains wiring with 4 wire 1.5 100 Mtr 90.90

sq.mm as per tender specification & IS.

56 SITC of Mains wiring with 4 wire 2.5 80 Mtr 126.25

sq.mm as per tender specification & IS.

57 SITC of Point wiring for Light / fan / Bell 37 Nos 354.51

/ Primary Point with 2nos. 1.5 sq. mm &

earth wire of 1.5 sq. mm (green) both are

of ISI marked 1.1 kv grade FRLS PVC

insulated multistrand copper wires , pipe

to be erected concealed in flushed on

wall / ceiling, complete with 6A Tissino

Type ISI marked flush type switch / bell

push & accessories erected on metal /

PVC Box covered with 3 mm thick PC

(Polycarbonate) / Acrylic sheet with

necessary lamp holder / ceiling Rose / H.

D. connector as directed with medium

class Rigid PVC pipe & accessories.

58 SITC of 6A independent Plug with 2nos. 6 Nos 313.10

1.5 sq.mm Cu. Mains size wiring &

earthwire of 1.5 sq.mm (green) both are

of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with

medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling,

complete with ISI marked 3 / 5 Pin socket

and tissino type switch erected with earth

continuity connection erected on Metal /

PVC box covered with 3 mm thick

PC(Polycarbonet) / Acrylic sheet.

59 SITC of 6/16A independent Plug with 6 Nos 607.01

2nos. 4 sq.mm Cu. Mains size wiring &

earthwire of 2.5 sq.mm (green) both are

of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with

medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling,

complete with ISI marked 3 / 5 Pin socket

and tissino type switch erected with earth

continuity connection erected on Metal /

PVC box covered with 3 mm thick

PC(Polycarbonet) / Acrylic sheet.

60 SITC of Single Phase 20A 3 Pin Metal clad 4 Nos 820.00

Industrial Type Socket with plug top and

20A SPMCB, suitable for flush mounting,

in 16 SWG MS box of suitable size and

covered with 3 mm thick electrical grade

hylam sheet or equivalent ISI marked

Electrical grade Bakelite sheet and

earthing with 2.5 sq.mm insulated copper

Signature of Contractor Executive Engineer (M&E)

wire run inside the conduit including

interconnections etc. complete as

61 LED LIGHT FIXTURES & LIGHTING: 25 Nos 589.84

SITC of Indoor wall mounting 20Watt or

up to 25% higher wattage LED 4 feet

Tube Light indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a

heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA

polyester powder coated and high U.V. &

corrosion resistance with diffuser and/or

Polycarbonate optics with company

120 to 300 V,Power Factor more than 0.9,

CCT 4000 K to 6500K, Uniformity ratio

Luminaries efficacy> 85 lumens/watt

LED driver efficiency > 85 %

(Each fitting required LM-79 & LM-80

Tube Light with integral / non-integral

driver, Surge-4KV,IP-20, 4 feet, Cat-III

62 3 watts LED Lamps integral type,cool 4 Nos 273.71

white with PC diffuser suitable for B22

63 SITC of 380mm sweep 1400 R.P.M 2 Nos 3,082.52

exhaust fan, capacitor type, having double

ball bearing, M.S.blades, mounting frame,

forearms, suitable to operate on 230V,50

HZ AC supply conforming to IS: 2312.Fan

shall be painted with epoxy grey colour

controlled by one 6 A flush type switch on

board and 6A plug point near Ex. fan.

64 SITC of 40W LED Surface / Wall mounted 3 Nos 5,194.43

LED Flood Light fittings with High power

White LEDs wattage of 1Watt and above

assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free

High pressure die cast aluminum housing

with smooth finish powder coated and

heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses

with company mark/name engraved or

120 to 300 V,Power Factor more than

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80

(IP-65), Surge -4KV Cat-III

Signature of Contractor Executive Engineer (M&E)

For Indoor use: (3 nos. at Pump House)

65 SITC of 'B' class galvanised iron pipe 32 11 Nos 558.53

mm outside dia 45 cms long duly welded

on 20 cms x 20 cms x 3 mm thick M.S.

base plate, erected on wall or corner for

mounting luminaries with necessary

hardware materials duly painted for wall

mounting indoor flood light fixtures on

Wall of Buildings & post top lantern.

66 EXTERNAL LIGHTING (Flood LIGHT): 4 Nos 6,088.28

SITC of 70W LED Wall mounted LED

Flood Light fittings with High power

White LEDs wattage of 1Watt and above

assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free

High pressure die cast aluminum housing

with smooth finish powder coated and

heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses

with company mark/name engraved or

120 to 300 V,Power Factor more than

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80

(IP-65), Surge -4KV Cat-III

For Outdoor use:

67 SITC of 40watt, Cat-III Post Top Lantern 2 Nos 4,819.72

LED fitting comprises of 650 MM TOP

Diameter, 120 degree beam angle with

Supporting Ribs and with 0.5mt. G.I.

fitting pipe (for Gate light)

68 EXTERNAL LIGHTING (STREET LIGHT): 4 Nos 10,178.78

SITC of Street Light Pole, steel tubular

swaged type, 7.5 meter long with single

arm & M.S.base plate with pipe cap and

over hung 1.5 m long having dia to suit

the socket of 240V LED street light

fixtures. Street light pole unit rate shall be

with (i) IP 65 SMC box of size 20 x 15 x

15 cms. with MCB & terminal strip inside

the box with hinged/sliding door (ii)

50mm dia, B class GI pipe bracket

min.1.5mtr long for Incoming & outgoing

cable (iii)MS Cable Clamp of 25 x 3mm

(iv)SITC of 1.5 Mtr.single Arm bracket of

medium duty MS pipe of 4.2 cms. Out

side dia complete with suitable sleeve

tubing 45 cms. long of required size of

pole top etc. and having spread of 1.5.mtr.

Signature of Contractor Executive Engineer (M&E)

length with 110 deg.(v) Complete painted

with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU

paint for Pole,Arm, pipe etc.

69 SITC of 70 W LED Street light fittings with 4 Nos 5,976.17

High power White LEDs wattage of 1Watt

and above assembled on single MCPCB,

efficiency more than 130 lm/w and

corrosion free High pressure die cast

aluminum housing with smooth finish

powder coated and heat sink extruded

aluminium with diffuser and

Polycarbonate optics/ lenses with

company mark/name engraved or

120 to 300 V,Power Factor more than

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80

Street Light (IP-65), Surge -4KV, 70 watt

70 SITC of M-20 / 1:2:4 cement concrete 4 Nos 1,292.80

foundation for Street light pole & 70 %

PCC from bottom including excavation for

the pole of size 60 x 60 x 120 cms. Deep in

below ground level with plinth of 45 cms

x 45 cms(or 45 cms dia x 45 cms) high

upper ground level with necessary curing

and finishing in approved manner.

71 DIESEL GENERATOR SET 2 Each 7,20,245.14

SITC of 75 kVA or higher standard rating,

415 V,50 Hz, 3 Phase, 4 wire Diesel

Generating Set. Diesel engine shall be

complete with necessary controls and

safety devices confirming to relevent

ISS/BSS with latest amendements, DG

controller unit with kWH meter. Diesel

Engine shall be suitable for continuous

operation of generator set duty inclusive

of fly wheel, air cleaner, radiator. fan with

guard, fuel pump, fuel filter, Electronic

governor, auto main fail starting,

electrical starting system with starter,

12V battery, voltage regulator,

instrument panel, Exhaust silencer,

protections against low lubrication oil

pressure,high water temperature.

Alternator shall be 415V, 3 phase, 50 Hz,

4 wire, 0.8 power factor, self excited,self

regulated,brushless type,drip proof

confirming to IS:4722 with latest

Signature of Contractor Executive Engineer (M&E)

The engine and alternator shall be

coupled over a sturdy common base

frame. Floor mounted,dust & vermin

proof, indoor type control panel shall be

consisting of Thermal magnetic MCCB of

suitable normal current rating,with

combined overload and earth fault

protective relays/release, voltmetre with

selector switch,ammeter of suitable range

with selector switch, frequency meter,

Energy meter, CTs, indicating lamps with

fuse and switch control, complete & with

necessary interconnections,fuses,lables

and other accessories.Day fuel tank with

necessary fuel hoses to the engine,all as

per detailed specification and complete in

all respect as required.

72 SITC of Acoustic enclosure suitable for 75 2 Each 1,92,414.09

kVA DG set, made out of 18 SWG, CRCA

Sheet, Sound absorbing matewrial

Rockwood of 64 density & 100 mm thick

conforming ti IS:8183. The resin boinded

Rockwood covered from inside level not

more than 75 dB at a distance of 1 mtr, as

PVCT / CPCB norms, on provided

73 Providing & laying of 50 MM Nominal OD 50 Mtr 62.62

Doubled Walled Corrugated Pipes (DWC)

of polyethylene (conforming to IS 14930 -

II) with necessary connecting accessories

like coupler, Tee, L - Bow, etc. of same

material at required depth (90 cms)

including excavation for laying of cable

below ground/ road surface for enclosing

cable and back filling the same to make

ground as per original & as per

instruction of Engineer Incharge -

74 Lightning Protection system for highest 1 Nos 60,760.00

building at plant area by air terminal

woith rod and GI strip conductor test link

to earth electrode as per requirement

75 SAFETY ACCESSORIES 2 Nos 8,671.86

SITC of following safety accessories

complete with necessary fixing brackets,

other accessories and tools etc. as

required to complete the job. Supply &

Erecting carbon dioxide (CO2) fire

extinguisher of 6.5kg capacity with

necessary clamps made from 50 x 6 mm

M.S. Flat with nut & bolts grouted in wall

(For 1 no. for LT Room, 1 no for DG set)

Signature of Contractor Executive Engineer (M&E)

76 Supplying & erecting D.C.P. type fire 2 Nos. 2,226.04

extinguisher for following capacity

cartridge type with gun metal cap

gram CO2 gas cartridge, powder and

brackets confirming to IS 2171 1985 and

complete erected with necessary clamps

made from 50 x 6 mm MS flat with nuts

and bolts grouted in wall complete, 10 kg

77 Supplying of standard first AID box with 1 Nos 299.97

antiseptic cream, medicine for use on

wounds due burn, crepe bandage, guage

bandage, medicated ready to use bandage

(Band-aid) adhesive tape for medicinal

user, scissors, antiseptic solution (Savlon

or similar) etc. (All above contents shall

be of standard makes)

78 Supply & fixing of printed instruction 1 Nos 130.29

(First Aid) Chart both in English and

Gujarati and duly framed with front

glasses, for treatment of person suffering

from electric shock.

79 Supplying & fixing of floor mounting 1 Nos 1,798.81

stand for keeping four nos. of FIRE

buckets comprising 1500 mm in length,

900 mm height frame made out of 30mm

X30 mm X 4 mm angle iron with cross

supports for legs, welded with 4 hooks

and duly painted with one coat of red

lead and two coats of approved

enamelled silver paint. ( 1 set for Dg set)

80 Supply and fixing of 20 W fluorescent 17 Nos 2,540.00

lamp operated emergency light with

maintenance free battery for 3 hours

operation during mains power failure.

81 Supply and laying of Synthetic Insulating 4 Sq.mtr. 1,027.17

Mat of Class - A of min. thickness 2mm as

per IS:15652 and with good electrical

insulation property for 1.1KV/3.3KV as

per site requirement. (For LT Panel)

82 Providing pair of rubber hand gloves ISI 1 Nos 214.12

make suitable for working on 22 KV

83 LIASONING CHARGES FOR OBTAINING 1 Nos 10,000.00

Power Liasoning Charges for obtaining

N.O.C from Electrical Inspector /

Statutory authority for Power / Ele.

Installation. (Fees shall be paid by

tenderer for obtaining N.O.C. from

Electrical Inspector / Statutory authority

on behalf of client and shall be

reimbursed on submission of original

receipt to Client).

Liasoning Charges shall include preparing

Signature of Contractor Executive Engineer (M&E)

required attested documents & drawing

for obtaining NOC on behalf of client

(Applicable Fees / deposits shall be

reimbursed by Client).

84 INSTRUMENTATION WORK 5 Nos. 1,426.12

PRESSURE MEASURING SYSTEM:

SITC of 0- 10 kg / cm2 - 150 mm dia, size

Pressure Gauge Design, Supply,

Installation, Testing, Commissioning of

Bourdon Type Pressure Gauge, ±1%

accuracy, Direct bottom 1/2" NPT (M)

process connection, IP 67, Glycerine

filled, SS304 Case with Bayonet Type

Bezel, SS316 L Bourdon Tube, SS

Movement material, Aluminium dial with

black graduation on white background,

Micro Zero adjustable pointer, neoprene

gasket, Blow out disc, shatter proof glass,

SS tag plate etc as per IS

85 Supply, installation, testing and 5 Nos. 29,438.47

commissioning of Pressure Transmitter

with local display along with two valve

manifold, required fittings, tubing (all

valves, fittings, tubings, etc. shall be in SS

316 only), all accessories, hardware, etc.

complete in all respects as per

specifications and having following

measurement ranges: Range : 0 -

4Kg/cm2 (at each pump delivery side and

86 LEVEL MEASURING SYSTEM FOR SUMP 5 Nos. 60,030.36

Supply, installation, testing and

commissioning of Ultrasonic type Level

Transmitter with remote type

transmitter with 20 meter cable between

Sensor and Transmitter along with all

required accessories, Weather proof

enclosure for transmitter for outdoor

application, mounting stand , etc.

complete in all respects as per

specification and having following

measurement ranges for liquid (Effluent)

Meas. Range: upto 10 m

87 Supply, installation, testing and 2 Nos 12,930.02

commissioning of Displacer type Level

Switch SS Float for dry run protection of

pump through relay multiplication in

PLC), etc., complete in all respects and as

per specification.

Meas. Range: upto 10 m

88 ELECTRO MAGNETIC FLOWMETER 3 Nos 1,49,342.84

Supply, installation, testing and

Signature of Contractor Executive Engineer (M&E)

commissioning of Full Bore

Electromagnetic flow meter comprising

of IP-68 Sensor with PTFE liner

Hastelloy-C Electrode, IP-66 transmitter

with 20 m cable between sensor and

transmitter along with all mounting

accessories, Weather proof enclosure for

transmitter, hardware, mounting stand,

etc. as per specification and to complete

the work in all respect as per site

condition necessary connection with

pipe and shall have following size. PN 1.6.

Meter Size : 300 mm NB

89 PLC BASED CONTROL PANEL 1 Nos 3,50,000.00

Supply, Installation, Testing &

Commissioning of PLC Based Instrument

control Panel with 10" color touch screen

HMI, 4G GPRS modem with (ethernet port

+ SIM slot) with SIM Card for Remote

data transmission to TEPS for monitoring

and control the EPS from TEPS,

Communication port for MFM , PLC with

Conformal Coating with ISA-S71.04

severity level G1;G2 as a min., Power

Surge Protection device in Incoming 230V

AC Power supply to UPS, 1 no. Spilt type

Air Conditioner (2 Ton 5 start rating )

Instrument Control Panel '(PLC Enclosure

/ Panel ) with necessary PLC based logic

and wiring , Min. 1 kVA online UPS (with

60 min backup alongwith filter for

harmonic, suitable rating SMF inbuilt

batteries alongwith battery charger and

all other accessories as per standard), etc.

complete in all respects and as per specs

with PLC having minimum I/O count of

70DI /30DO / 12AI /4 AO. These are the

minimum IO requirement if any other

IO,s required to complete the work

contractor shall be provide the same

without any extra cost.

90 INSTRUMENT CABLE & ACCESSORIES 80 Mtr 144.00

'Supply, Laying, Installation, Connection,

Termination, Testing & Commissioning of

Instrument Cables as per specs.The unit

rate shall include

a)Supply, loading & unloading of the

cable at site from store.

b)Shifitng of cable from site store to place

of installation.

c)Fixing of cable clamps, brackets,

supports, route markers etc. where ever

required to fix the cables safely.

d)Excavation, back filling and levelling of

Signature of Contractor Executive Engineer (M&E)

ground alongwith laying of fine sand,

protection bricks and other necessary

civil material for laying cables outside the

f)Testing and submission of sketches &

reports of all the cables laid.

91 SIGNAL CABLE 80 Mtr 118.00

92 CONTROL CABLE 80 Mtr 270.00

93 INSTRUMENT CABLE TRAY 80 Mtr 832.00

Supply and installation / erection of

Perforated type cable tray of galvanized

mild steel sheets of 2 mm thickness with

required, hardware, fitting and support

structral asccessories . All material shall

be Hot dip galvanised as per IS 2629 and

tray hardware shall be in GI. Support

structutre shall be of structral steel for

mounting the cable tray on wall / cable

trench or as per site condition,

600 X 25 mm - Perforated type

94 200 X 25 mm - Perforated type 80 Mtr 322.00

95 50 X 25 mm - Perforated type 80 Mtr 107.00

96 CABLE END TERMINATION AND 20 Nos 136.00

'Supply, fixing, connection, testing and

commissioning of double compression

brass cable glands and crimping type

Bimetalic lugs / sockets with necessary

tools and equipments as specified in

specifications and IS complete in all

respects. The glands and lugs / sockets

shall be suitable for cable size and type

mentioned above. The job also includes

earthing the glands and armour of the

cable with common earth bar or flexible

copper mesh as applicable.

97 SIGNAL CABLE 24 Nos 136.00

98 CONTROL CABLE 38 Nos 296.00

99 IoT Based Dual Protocol (GSM + LAN) 1 Nos 19,500.00

Gateway for Centralise Monitoring and

Data Connectivity to GPCB and CPCB.

Cloud Software Charges.

Signature of Contractor Executive Engineer (M&E)

100 Cloud Software Platform and IIoT Sensors 1 Nos 45,50,000.00

for Predictive Maintainanace and AI

Powered Electrical Signature Analysis for

Electrical Pumps.

Total Amount Without GST in Rs.

Total Amount Without GST in Rs.

*The rate shall be Exclusive of all taxes (Excluding GST)

I/We agree to carry out above work at __________ % above the estimated Rate put to tender

Percentage in words ( _______________________________)

I/We agree to carry out above work at __________ % below the estimated Rate put to tender

Percentage in words ( _______________________________)

Estimated Amount put to Estimated Amount put to

Tender Rs. 1,45,30,488.00 Tender Rs.

Add % Above Rs.____________ . Deduct % Below Rs.____________

Net Amount Rs.____________(In figures). Net Amount Rs.____________(In figures)

I/we have read the condition mentioned in this tender and agree to abide by the sam

IMPORTANT NOTE:

The rate of each items should be offered inclusive of Excise duty, packing, forwarding, insurance,

loading, unloading, shifting & transportation at store/site except GST of work of the estates under

GIDC, Bharuch GST will paid extra Please note that the agency, in whose favour the tender is

finalized by the competent authority, should have to submit the document like insurance of the

staff engaged RPFC No., Labour license etc.

1. I / we agree to supply the above materials at the rate mentioned above.

2. I / we have read the conditions mentioned in this tender & agree to abide by the same.

3. GIDC will not issue any tax exemption form i.e. ‘P’, ‘C’ or ‘D’. The tenderer may quote

rates accordingly.

4. The agency in whose favour tender is finalized has to enter into B1 agreement and

conditions and clauses of the agreement shall be binding to the agency. If agency desire

to study, the same is available from Engineer in Charge during working days and office

5. The tendered has to inspect the site and found out the quantum of repairs/overhauling

service work involved before quoting the rates.

6. Labour work required for handling, lifting lowering, shifting, loading, unloading,

transportation etc. of any pumps & allied equipments with tools & tackles shall be

arranged by the tenderer.

Signature of Contractor Executive Engineer (M&E)