Service and Maintainance of Existing Pump Motor system for the Year of 2026-27

KAD_Motor Rewinding upto 3 HP

KAD_Motor Rewinding upto 5 HP

KAD_Motor Rewinding upto 7.5 HP

KAD_Motor Rewinding upto 10 HP

KAD_Motor Rewinding upto 12.5 HP

KAD_Motor Rewinding upto 15 HP

KAD_Motor Rewinding upto 17.5 HP

KAD_Motor Rewinding upto 20 HP

KAD_Intermediate Piece (I.P.) with I.P. Leaded Bronze Bush

KAD_Oil Seal (Pump Oil Seal)

KAD_Oil Seal Steel Bush (Oil Seal Sleeve)

KAD_Impeller Shell moulded with aluminium & bronze

KAD_Discharge Outlet (D.O.) Bearing(LB bush) and D.O Steel bush (SS sleeve)

KAD_D.O. Bearing( I.D.O LB bush)

KAD_Steel Bush (I.D.O. SS sleeve)

KAD_Allen Screw

KAD_Pump Shaft (Stainless Steel) Counter less ground with key way upto 8 stages

KAD_Pump Key (Stainless Steel) Upto 8 stages

KAD_Pump coupling (Stainless)

KAD_Non-Return Valve assembly complete with rubber O rings

KAD_Cable Guard

KAD_Brass Filter

KAD_Labour Charges (Overhauling of pump only)

KAD_Upper Flange

KAD_Lower Flange

KAD_Upper Housing

KAD_Lower Housing

KAD_Lock Ring (Circlip Big)

KAD_Starter 3 HP

KAD_Starter 4 HP

KAD_Starter 5 HP

KAD_Starter 7.5HP

KAD_Starter 10HP

KAD_Starter 12.5 HP

KAD_Starter 15 HP

KAD_Starter 17.5HP

KAD_Starter 20 HP

KAD_Carbon housing (TB Plate)

KAD_Thrust Bearing block assembly (TB Bottom)

KAD_Tip Carbon/Ferrode Padding

KAD_Studs and Nuts

KAD_Bearing (Gun Metal Bush) centrifugal cost aluminium bronze bearing bush

KAD_Circlips(small)

KAD_Motor Base with Pin

KAD_Transportation of Pumping machinaries

KAD_Re-errection charges of Pumping machinery including overhauling and painting

KAD_Lifting of submersible pumpsets

KAD_Labour Charges Overhauling

KAD_Labour charges for Lifting of non functioning submersible pump set along with cable and GI pipes

KAD_Labour charges for lowering additional GI pipes of dia 32 / 50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI pipes should be handed over to the department (Labour charges only) Upto 3 lengths

KAD_Labour charges for lowering additional GI pipes of dia 32/50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI pipes should be handed over to the department (Labour chargesonly) above 3 lengths

KAD_Lifting of struck up submersible pump set upto 300 ft (BWSSB SR 2017-18/O150G/Sl No.26)

KAD_Lifting of struck up submersible pump set above 300 ft (BWSSB SR 2017-18/O150G/Sl No.27)

KAD_Labour charges for Laying U.G. Cable upto 3.5 core 25 Sq.mm as per PWD Electrical SR 2010-11, P-68,1-1, Class A PVC cable

KAD_Refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification PRE SR 2011-12, P-3,1-6.

KAD_Fabricating, Supplying and mounting MS Box made out 14 SWG suitable for Foor/Wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enamelled metal paint etc., complete

KAD_Supplying and fixing angle iron frame work fabricated out of M.S. angle iron and M.S. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (PWD ELE SR 2014-15, Pg.No.49, lt.No.6.39.3)

KAD_Erection of panel Board & MS Box (Outdoor type) (Gulbarga PRED, Pg.No.57, lt.No.12.2)

KAD_Supplying and fixing polished wood board made out of not less than 15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc

KAD_Supply and fixing of hylam brand hand plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using NF Screw

KAD_Supply and fixing of 16 Amps Contactor

KAD_Supply and fixing of 25 Amps Contactor

KAD_Supply and fixing of 33 Amps Relay

KAD_Supply and fixing of 23 Amps Relay

KAD_Supply and fixing of 15 Amps Relay

KAD_Supply and fixing of Single Phase Preventer_7.5 to 15 HP

KAD_Supply and fixing of Single Phase Preventer_20 to 30 HP

KAD_Supply and fixing of RYB Rotary Switch_volt selector

KAD_Supply and fixing of Terminal Plate_connector 30A

KAD_Supply and fixing of Terminal Plate_connector 60A

KAD_Supply and fixing of No-Volt_NV_Coil

KAD_Supply and fixing of wiring kit_DOL upto 7.5HP

KAD_Supply and fixing of wiring kit_SD upto 25HP

KAD_Supply and fixing of LED Indicator

KAD_Supply and fixing of Ammeter

KAD_Supply and fixing of Voltmeter

KAD_supply and fixing of Blade set 16A

KAD_supply and fixing of Blade set 25A

KAD_Supply and fixing of CT Coil 50 bar 5 and 75 bar 5

KAD_Labour Charges_for over hauling

KAD_Gl Pipe Threading including transportation

KAD_Cable Joint