RETENDER Annual Plan-TVPM DP 2023-24 Construction of Paruthipally School Water Tank Aryanad Division 1055/24-Project No 1055/24

Amount

water Tank

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

OD169568/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge .All works above plinth level (Note :- Cement content considered in this item is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.48.3:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

OD171324/2023-2024:1.021-Specification code: 100.36.1 Filling water with 5000 litre tankers fited in lorry and conveying water from a distance of 5 km (average) to the reservoir site and pumping the water into the reservoir of height not less than 3 m using 5 HP diesel engine pump set , hire for tanker lorry, tools and other appliences and cost of water etc. complete.

OD171588/2023-2024:Providing and fixing tile profile terafold sheet roofing accessories 0.35 mm(+0.05%)total coated thickness,zinc coating 120 grams per sqm qw per IS:mm(+0.05%)total coated thickness,Zinc coating 120 grams per sqm as per IS:277.in 240 mpa steel grade,5=7 microns using self drilling/self tapping screwscomplete:Ridges plain(500-600)

10.26.3:Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes

16.71:Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer - in- Charge.

OD172326/2023-2024:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Hand Wheel PN 1.6, Size 100mm

OD173139/2023-2024:Providing standard pipe earth station for lightening arrester with 40 mm dia 3.75m long class B.GI pipe confirming IS (latest edition) including supply of all materials and providing chamber and cover etc .complete

18.17.3:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

OD172258/2023-2024:Supplying and fixing name board of size 75x60cm granite plaque engraving letters etc.Complete as per direction of e-i-c

18.17.2:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.1A:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

OD272329/2023-2024:Providing and fixing ASTM pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step ASTM solvent cement and testing of joints complete as per direction of Engineer -in-Charge 20 mm dia SH-40- Exposed on wall

OD272348/2023-2024:Providing and fixing ASTM pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step ASTM solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia SH-40- Exposed on wall

OD272359/2023-2024:Providing and fixing ASTM pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step ASTM solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia SH -40- Exposed on wall

OD272423/2023-2024:Providing and fixing ASTM BALL VALVE SH-80 of approved quality 32 mm nominal bore

OD272906/2023-2024:Providing and fixing ASTM ball valve of approved quality, 20 mm nominal bore SH-80

OD272910/2023-2024:Providing and fixing ASTM ball valve of approved quality :50 mm nominal bore SH-80

OD272936/2023-2024:Providing and fixing ASTM moulded fittings/ accessories for ASTM pipes, including jointing with ASTM solvent cement -50*32mm dia Reducer

OD272954/2023-2024:Providing and fixing ASTM moulded fittings/ accessories for ASTM pipes, including jointing with ASTM solvent cement - 32mm dia Elbow

OD272965/2023-2024:Providing and fixing ASTM moulded fittings/ accessories for ASTM pipes, including jointing with ASTM solvent cement - 50mm dia Elbow

OD272979/2023-2024:Providing and fixing ASTM moulded fittings/ accessories for ASTM pipes, including jointing with ASTM solvent cement - 20mm dia Elbow

OD272980/2023-2024:Providing and fixing ASTM moulded fittings/accessories for ASTM pipes, including jointing with ASTM solvent cement - 32*20 mm dia Reducer

T.VIJAYAKUMAR

ANILKUMAR N

Bidder Name

ANILKUMAR N

T.VIJAYAKUMAR

RAJASEKHARAN NAIR