Tender for construction of

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (HSR- 4.14.1)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. (HSR- 4.32)

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. ( HSR- 4.33)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded stone aggregate 40mm nominal size) (HSR-.6.1.6)

Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) 40 MM (HSR-6.8.2)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level. 1 : 1. 5: 3 (1 cement : 1. 5 coarse sand (zone-Ill): 3 cum graded stone aggregate 20 mm nominal size) (HSR- 6.14.1)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mm nominal size). (HSR- 6.15.1)

Reinforced cement concrete work in beams, suspended floors, cum roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR- 6.16)

Reinforced cement concrete work in arches, arch ribs, domes, Vaults, shells, folded plate and roofs having slope more than 15° up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size). (HSR- 6.18)

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1 ½ coarse sand(zone-111) : 3 graded stone aggregate 20mm nominal size). ( HSR- 6.21)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete. ( HSR-6.30.1)

Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc. ( HSR-6.30.2)

Suspended floors, roofs, landings, balconies.( HSR-6.30.3)

Shelves (Cast in situ). ( HSR-6.30.4)

Lintels, beams, plinth beams, girders, bressumers and cantilever. ( HSR-6.30.5)

Columns, Pillars, Piers, Abutments, Posts and Struts. ( HSR-6.30.6)

Stairs, (excluding landings) except spiral-staircases. ( HSR-6.30.7)

Vertical and horizontal fins individually or forming box sqm louvers band, facias and eaves boards. ( HSR-6.30.13)

Extra for shuttering in circular work (20% of respective centering and shuttering items). ( i.e 20% of 293.00 (for circular Column) ( HSR-6.30.14)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more. (HSR- 6.33.6)

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in:. ( HSR-7.21.2)

Brick work with common burnt clay non-modular bricks of class Designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : (HSR- 7.22.2)

a) First Storey

b) Second Storey

c) Third Storey

Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in foundations and plinth in: ( HSR-7.27.2)

Half brick masonry with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level. (HSR - 7.28.2)

a) First Storey

b) Second Storey

c) Third Storey

Providing & Fixing factory manufactured jali of reinforced cement concrete consisting of cement coarse sand and 10 mm and down gauge bajri in the ration of 1:1:2 with 8 mm dia for steel. Outer framed of the jali will be 50 mm wide and 25 mm thick and liner frame of jali will be 25 mm wide and 25 mm thick and with smooth finish as per the design approved by the Engineer-in-Charge including fixing in position up to any height with cement sand mortar 1:4 complete in all respect. (HSR-.8.17)

Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (HSR-.9.17.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement each 77 88 165 concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR-.9.18)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (i) Single socketed pipes.110 mm dia PVC pipe (HSR-9.57.2)

150 mm dia PVC pipe (HSR-9.57.3)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. 110 mm dia PVC Bend. (HSR-.9.58.5.2)

150 mm dia PVC Bend. (HSR-.9.58.5.3)

Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. FIRST Storey ( HSR-.10.1)

Providing and laying of screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping. (HSR-.10.4)

a) Second Storey

b) Third Storey

Providing and laying of precast terrazzo tiles 20 to 22 mm thick with graded marble chips of size up to 12 mm, laid in floors, and landings, jointed with neat cement sluny mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement:4 coarse sand) Medium shade pigment using 50% white cement and 50% ordinary cement. (HSR-10.26.2)

a) Second Storey

b) Third Storey

Providing and laying of chequered terrazzo tiles 20 to 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement sluny mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement : 4 coarse sand) Medium shade pigment using 50% white cement and 50% ordinary cement. ( HSR- 10.29.2)

a) Second Storey

b) Third Storey

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : 10.37.1 25 mm thick ( HSR- 10.37.1)

a) First Storey

b) Second Storey

c) Third Storey

Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. ( HSR- 10.38 )

a) First Storey

b) Second Storey

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. (HSR-.10.42)

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.( HSR- 10.43)

Providing and laying Baroda Green marble stone 17mm and above thick in risers of step, skirting , dado, pillars and wall lining included matching the grains of marble slab in any pattern as specified laid over 12mm thick cement sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing. The rates are for all heights / storey. The sample shall be got approved from Engineer In Charge. ( HSR- 10.47 )

a) First Storey

b) Second Storey

c) Third Storey

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer- in-Charge: Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. ( HSR- 10.49.1)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. ( HSR- 10.60)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. ( HSR- 10.62)

1Omm thick cement plaster 1 :3 (1 cement: 3 fine sand) (HSR-11.4.2)

a) First Storey

b) Second Storey

c) Third Storey

12 mm cement plaster of mix : 1 :6 (1 cement: 6 fine sand) (HSR-11.5.4)

a) First Storey

b) Second Storey

c) Third Storey

15 mm cement plaster on the rough side of single or half brick wall of mix : 1 :6 (1 cement: 6 fine sand) (11.6.2)

a) First Storey

b) Second Storey

c) Third Storey

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. (HSR-11.58)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer(HSR-11.64.1)

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works (HSR-11.68.3)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR-11.78)

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 litre/1 O sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (HSR-11.95.1)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws. Kiln seasoned and chemically treated Hollock wood. 30 mm thick. (HSR-12.10.2.2.)

Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick (HSR-12.12.1)

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 30 mm thick shutters With ISI marked stainless steel butt hinges of Kiln seasoned and chemically treated Hollock wood 9HSR-12.19.2.2.2.

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws (HSR-12.37.1)

30 mm thick including ISi marked Stainless Steel butt hinges with necessary screws (HSR - 12.37.2)

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm (HSR-12.74.1)

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm (HSR- 12.75.1)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight up to 3 6 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. (HSR 12.89)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike- plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in- charge: (HSR-13.3)

Profile C Fixing with adjustable lugs with split end tail to metre each jamb (HSR-13.3.2.1)

Profile B Fixing with adjustable lugs with split end tail to metre each jamb (HSR-13.3.1.1)

Profile E Fixing with adjustable lugs with split end tail to metre each jamb (HSR-13.3.3.1)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (HSR-13.29.2)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80 x 1.25 mm M.S. laths with 1.25 mm thick top cover (HSR-13.37.1)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes (HSR-13.10.1)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS.2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1 :5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick joint less cement mortar of mix 1 :4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. "All above operations to be done in order and as directed and specified by the Engineer-in-Chage: With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (HSR-28.17.1 )

(NS ITEMS ) Providing & fixing Stainless Steel Fittings (Chrome Finished) to doors,window,cupboard etc. (Grade 304) with nuts & screws etc complete.(as per sample approved by Engineer-in-charge) (NS)

i) S.S tower bolt (8" long)

ii) S.S tower bolt (6" long)

iii) S.S sliding bolt (250 mm long)

vi) S.S REAR MAGNETIC DOOR STOPER.

vii) 150 mm floor S.S front Door stoppers (Godrej or equivalent make) with rubber cushion screws etc to suit shutter thickness complete.

Providing and fixing polycarbonate sheet sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws with EPDM seal, and the joints shall be provided with aluminium strips at top and bottom as a seal complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Pollycarbonate sheet Multiwalled 10mm thick. ( N.S CSR-20 13.27(v)(a)

(PUBLIC HEALTH WORK ) Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia (HSR-4.16.1.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size) (HSR-6.1.2)

Cement Concrete 1 :8:16 Flooring Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. (HSR- 10.100.2)

Drilling and tapping cast iron pipe lines of all diameters and screwing in ferrule and connections -Ferrule size 25 mm (HSR-20.24.4)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 11.43 cm thickness of walls (HSR-20.26.1)

22.86 cm thickness of walls (HSR-20.26.2)

Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I.inspection chamber cover and frame weight as per 1.5.1. specification painted with 3 coats of black bitumastic superior paint complete as per standard design.Size 450 mm X450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with C.C. topping (HSR-21.84.1)

Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping) (HSR-21.84.2)

Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab) (HSR-21.84.3)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 200mm i/d (HSR-21.94.3)

Providing , lowering, cutting, jointing and testing RCC pipe ClassNP-3 as per IS 458-2003 with Spigot and Socketed joints manufactured with ISI marked Sulphate Resistance Cement as per ISI 12330 with rubber rings ISI marked, antitermite as required at site, into trenches, for all depths and laying out the same to correct alignment, gradients and levels including dressing and trimming and cutting of concrete beds and sides of trenches, if required, Jointing with rubber rings in trenches and jointing with 1:1 ½ cement sand mortar and with end dowels filled with 1:1 ½ cement sand mortar and finishing the joints at an angle of 45degree with faces of spigot of socket joints cutting and finishingthe cut surface to a uniform finish etc. as fully described in HSR item No. 29.38, 29.44, 29.45 & 29.46 including cartage, loading and unloading complete in all respects. The internal diameter of the sewer being. 450 mm internal dia (HSR-21.95.3)

Providing and fixing white vitreous chinaware laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required. Size 600x450x200 mm (HSR-22.6.2)

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge). Two way (HSR-22.8.2)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls Kitchen sink without drain board 610x460 mm bowl depth 200 mm (HSR-22.10.2.2)

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (HSR-22.22.1)

Providing and fixing white vitreous chinaware pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaware flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. W.C. pan with ISi marked white solid plastic seat and lid (HSR-22.24.1)

Providing and fixing white vitreous chinaware battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. (HSR-22.46)

Providing and fixing partitions for different type of urinals. Vitreous Chinaware Partition plate. Large size 835mm x 355 mm (HSR-22.50.1.2.1)

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100mm dia pipe (HSR - 22.53.1)

For 75 mm dia pipe (HSR - 22.53.2)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100mm inlet ans 75 mm outlet Sand Cast Iron S&S as per IS - 1729) (HSR- 22.80.2.2.)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc. External work. 25 mm dia nominal bore (HSR-22.88.3)

32 mm dia nominal bore (HSR-22.88.4)

50 mm dia nominal bore (HSR-22.88.6)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15mm dia nominal bore (HSR-22.89.1)

20 mm dia nominal bore (HSR-22.89.2)

Providing and fixing gun metal gate valve( heavy pattern ZOLOTO/SANT/KARTAR make) with hand wheels, on G.I pipelines laid in inside/outside building including threading, testing complete in all respects 20mm internal diameter (HSR-22.98.2)

25 mm internal diameter (HSR-22.98.1)

32 mm internal diameter (HSR-22.98.3)

Providing and fixing Unplasticised PVC connection pipe with brass unions: 45 cm length 15mm nominal bore (HSR-22.101.2)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore. (HSR-22.103.3)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15mm nominal bore (HSR-22.104.1)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (HSR-22.106.1)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (HSR-22.107.1)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings rrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms (HSR-22.119.2)

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid (HSR-22.123.2.1)

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (HSR-22.127)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay non-modular bricks of class designation 7 .5 (HSR-22.166.1.1)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. 2000 Litres. Capacity (HSR-22.182 a)

b ) 5000 Litres. Capacity

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap standard pattern) the weight of cover to be not less than 4.5 kg. ( HSR-22.202)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (HSR-22.209)

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. (HSR-22.211)

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair 115mm long without CP fittings complete in all respect. Size 560mm x 410mm (above counter oval) (HSR-22.221.6)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type-B 110 mm Outer Dia (HSR-22.222.2)

90 mm Outer Dia. (HSR-22.222.3)

Providing and fixing UPVC SWR soil,waste Fittings Type-B having 6 Kgf/cm2 conforming to IS:14735-99 (Supreme/Finolex/ Prince/ Diplast make) inside/outside the building including cost of solvent for jointing, complete in all respects. (NS)

a) 110mm Outer Dia.

i) Plain Bend

ii) Door Bend

iii) Plain Tee

iv) Door Tee

v) Socket

b) 90mm Outer Dia.

i) Plain Bend

ii) Door Bend

iii) Plain Tee

iv) Door Tee

v) Socket

Providing & Fixing UPVC SWR floor traps with 75 mm i/d outlet. I.S.I. marked of the self cleaning design including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc. minimum depth of water should be 50 mm with a minimum seal of 50 mm. complete in all respects. (NS)

(ROAD WORK) Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (HSR-4.14.1)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1½:3 (1 Cement: 1½ coarse sand(zone-111) : 3 graded stone aggregate 20mm nominal size) (HSR-6.3.1)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR-7.21.1)

Cement Concrete 1 :8:16 Flooring Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. (HSR-10.100.2)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer (HSR-11.67.1)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications: Two or more coats applied on walls @ 1.25 litre/10 sqm over and including one coat of Special primer applied @ 0. 75 litre /10 sqm (HSR-11.97.1)

Construction of Embankment CBR 8% (for new road/ raising/ berms/ etc.) with approved material obtained from borrow pits, including compensation of earth with all lead and lift transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2, as per technical clause 305 of MORT&H specifications. (HSR-17.6)

Granular Sub-Base with Coarse Graded Material - Grading-I or II or III (Table:- 400-2) Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.of MORT&H specifications. Grading III material. (HSR-17.15.3)

Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. (HSR-17.69.2)

Electrical Items Supply and erection of miniature circuit Breaker 240/415V in the existing distribution board including making necessary connections:- SP MCB of 9 KA breaking capacity 6 amp. to 32 amp.(12way SPN 3x12+8 way SPN 3x8 12wayTPN HorizontalDB o/g 12x36=492) HSR -23.22.5.1

DP MCB of 9 KA breaking capacity 40 amp. to 63 amp. ( For 4way TPN HDB out goings for UPS Supply) HSR -23.22.5.4

FP MCB of 9 KA breaking capacity 40 amp. to 63 amp. (4way vertical outgiong 6x3 + Incoming for 12No HDB 1x12+TPN MCB Box 1x3+ For UPS TPN HDB incoming 1x1 =34No) HSR -23.22.5.8

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Ceiling rose flush/surface type HSR – 23.8.1.5

Bakelite angle/straight button holder large size. HSR – 23.8.1.12

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. HSR – 23.8.4 .

Erection of exhaust fan in existing opening ,complete with necessary earthling of fan including carriage from PWD store to the site of work. HSR -23.9

Making suitable hole in the wall suitable for exhaust fan up to 450 mm sweep including finishing the same and fixing of Stainless steel wire mesh 2 mm thick having about 50 meshes per inch at exhaust side complete as required HSR – 23.11

Providing and fixing outdoor duty Ply of 12 mm thick frame suitable for exhaust fan up to 450 mm sweep etc complete as required HSR – 23.12

Fixing of LED Tube light 1x18 & 2x18/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required HSR – 23.20

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. HSR – 24.1.3

Extra for charcoal or coke and salt for G. I. plate or copper plate earth electrode. HSR - 24.1.5

Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required HSR – 24.1.7

Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. HSR – 24.1.11

Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. HSR – 24.1.8

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. HSR – 24.1.13

XLPE INSULATED LT CABLES: XLPE INSULATED ARMOURED CABLES (UNDERGROUND): Supply, laying and erection of aluminium onductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS:7098 (Part-1)1988 to be laid 1metre below ground level including excavation, sand cushioning, covering with sand & First Class bricks and back filling the trench etc., of the required size as per PWD General Specifications:- Overall size 35sq.mm (3½ Core) Armoured (Underground) CSR - 34.10 A (xxiii)

Overall size 50sq.mm (3½ Core) Armoured (Underground) CSR - 34.10 A (xxiv)

Overall size 120sq.mm (3½ Core) Armoured (Underground) CSR - 34.10 A (xxvii)

Overall size 150sq.mm (3½ Core) Armoured (Underground) CSR - 34.10 A (xxviii)

Overall size 300sq.mm (3½ Core) Armoured (Underground) CSR - 34.10 A (xxxi)

Overall size 16sq.mm (4Core) Armoured (Underground) CSR - 34.10 A (xxxvii)

Supply and erection of suitable compression type brass cable glands for underground Cable :-10 sqmm to 16s qmm Cable 2 to 4 Core HSR – 24.2.7.2

25 sqmm to 50 sqmm Cable 2 to 4 Core HSR – 24.2.7.3

120 sqmm to 185 sqmm Cable 3 to 3.5 Core HSR – 24.2.7.5

300 sqmm to 400 sqmm Cable 3 to 3½ Core HSR – 24.2.7.7

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work . 16 sqmm HSR – 24.2.8.4

35sqmm HSR – 24.2.8.6

50sqmm HSR – 24.2.8.7

120 sqmm HSR – 24.2.8.10

150 sqmm HSR – 24.2.8.11

300sqmm HSR – 24.2.8.14

SAFETY ITEMS Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages. HSR – 23.26.1

Supply and erection of shock restoration chart in glass frame. HSR – 23.26.3

COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group B (ceiling fan 108+Ex fan 10+2x18 Tube Light183+1x18 aTube lights 80 + Wall Lights105+ Mirror lights 13 + Call Bell 2=501 HSR – 23.4.1.2

Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe.Group B HSR – 23.4.2.2

Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch ( 501-428=73) Group B HSR – 23.4.3.2

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group B (for LP with Power Plugs) HSR – 23.4.4.2

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group B (for AC Points 59 +for AC Points 32) HSR – 23.4.5.2

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) (For Sub Mains SB to SB ) HSR – 23.3.6.1

1 run of Size 2.50 Sqmm(1.1.80mm) (For Sub Main DB to SB with Plug (56x15+Wiring of UPS computer points 30x15==1290mtr) HSR – 23.3.6.2

1 run of Size 4 Sqmm(1/2.24mm)( For Misc Jobs) HSR – 23.3.6.3

1 run of Size 6 Sqmm(1/2.80mm) (for Sub Mains OF 12 Way & 8Way Horizontal SPN DB's) 6x15=90 Say 100 HSR – 23.3.6.4

1 run of Size 10 Sqmm(1/3.50 mm) 12x2x15=360(Sub Mains to 12 Way horizontal DB's Power& Lighting12No) HSR – 23.3.6.5

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 8 way ( 2 incoming and 6 outgoing)( For UPS Supply distribution FF) HSR – 23.22.4.2

SPN DB Double Door 12 way ( 2 incoming and 10 outgoing)( For UPS Supply distribution GF) HSR – 23.22.4.3

TPN DB Horizontal type Double Door 4 way ( 8 incoming 3phase*4 outgoing)( For UPS Supply Distribution) HSR – 23.22.4.5

TPN DB Horizontal type Double Door 12 way ( 8 incoming 3phase*12 outgoing) ( Power & Lighting DB,s) HSR – 23.22.4.8

Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. DP RCCB 30ma sensitivity , 40 A HSR – 23.22.6.2

FP RCCB 30ma sensitivity, 40 A(For Lighting DB,s) HSR – 23.22.6.5

FP RCCB 30ma sensitivity, 63 A9For Power DB,s) HSR – 23.22.6.6

Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 20 mm dia. HSR -23.7.6.1

PVC pipe of 25 mm dia. ( For wiring of computer points 30x20=600 HSR -23.7.6.2

PVC pipe of 32 mm dia. HSR -23.7.6.3

PVC pipe of 40 mm dia. HSR -23.7.6.4

FITTING AND ACCESSORIES Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Call bell 220/230 volts musical type HSR – 23.8.1.6

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch (for plug on SB 56+LP 59=115) HSR – 23.8.11.1

5 amp 2 way switch HSR – 23.8.11.2

15 amp 1 way switch (PP59+ CP33=59) HSR – 23.8.11.3

5 amp Socket ( Plug on SB56+LP 59+CP3x33=214) HSR – 23.8.11.4

15 amp 6 pin Socket (PP=59) HSR – 23.8.11.5

Bell Push HSR – 23.8.11.6

step type Fan Regulator 2 modules 300 watt HSR – 23.8.11.7

Telephone Socket outlet modular type HSR – 23.8.11.8

TV Socket outlet modular type HSR – 23.8.11.9

Blanking plate HSR – 23.8.11.10

RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type HSR – 23.8.11.11

USB Charger, 1000mA, 5V, 1 Module ( For Non residential use only) HSR – 23.8.11.12

32A D.P. Main Switch With Key Ring Tag 2 Module ( For AC Points ) HSR – 23.8.11.13

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data HSR – 23.8.10.1

3 Modules HSR – 23.8.10.2

4 Modules HSR – 23.8.10.3

6 Modules HSR – 23.8.10.4

8 Modules HSR – 23.8.10.5

12 Modules HSR – 23.8.10.6

MISCELLANEOUS Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. 2 pair telephone wire HSR – 23.23.8.1

Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required HSR – 23.23.9

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required DSR – 1.19.

S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HOPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dialinner dia HSR – 24.5.2.3

Supply and erection of sheet steel enclosures 1 pole/2 pole/4 pole on wal Von existing pedestal complete as require. S.P.N. or DP enclosure suitable for DP MCB HSR - 23.22.3.2

TPN enclosure suitable for TP , TPN or FP MCB HSR - 23.22.3.3

Supply and erection of suitable MS/GI Box covered with 5 mm thick Bakelite sheet as below 75 mm x 75 mm x 60 mm deep M.S. box for telephone and inter-communication system HSR – 23.8.3.1

Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 100 X 50 X2mm HSR – 23.23.6.1

MS perforated cable tray painted with powder coating 200 X 50 X2mm HSR – 23.23.6.2

AREA LIGHTING Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) each 573 making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections. HSR – 24.4.3

Supply and erection of Three Phase weather proof M.S. box of size 30 cm x 20 cm x 15 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 16 amp TP MCB and 4 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box and necessary connections HSR – 24.4.6

MS STAND, BUS BAR CHAMBER AND PANELS Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide.( LT Panel Stand) HSR – 23.24.1

Supply and erection of Modular case circuit breaker single pole/4 pole onexisting wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA HSR – 23.22.1.9

4 pole MCCB 200 to 250 amp, 25 KA( 9 for LT Panel+ 6 for VDB) HSR – 23.22.1.11

4 pole MCCB 300 to 400 amp , 50 KA HSR – 23.22.1.12

MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 250 A FP HSR – 23.22.2.2

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/ pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work.4 pole MCCB 6 amp to 100 amp , 25 KA HSR – 23.22.1.9

4 pole MCCB 125 to 160 amp, 25 KA HSR – 23.22.1.10

SITC 2x18W T8 LED 1200mm Batten Light. The Endura Fixture is a surface & wall mounted LED batten with extruded aluminium housing and robust construction . PF>.95, System Wattage LED 2x180W with Minium 1500 lumens in 5700k. The Fixture should be of Makes :-BAJAJ(BATTON 112182 BLRB-DB218+ TUBE LIGHT 112432 BLRB 2x18W CWC )/PHILIPS /GE/OSRAM/CGL NS-1

SITC of 15W LED Surface mounted round/square type downlighter. The Fixture should be Made of Extruded Aluminium Housing. Inbuilt Protection of 2kv, PF>.95, System Wattage 15Wintegral housing for driver. Minium 100 lumens/W in 5700k. The Fixture should be of Makes BAJAJ(112548-BGSLO-15W SQ)/ PHILIPS-SM200C LED15S 4000 PSU OD WH/ CGL: LCDSPL-S-18-CDL/OSRAM/GE/WIPRO NS-2

SITC of LED Surface Mounted Square/Rect. Bulkhead Light. The Fixture should be Made of PDC Housing.PF>.95, System Wattage 10w with Minium 100 lumens/W in 5700k. The Fixture should be IP-65of Makes :-PHILIPS(WT202WLED6SNWPSUS2PC)/ BAJAJ(112334-BIBWP 10W LED) /CGL: LBHN-10-CDL/GE/OSRAM/WIPRO NS-3

SITC 1x18W T8 LED 1200mm Batten Light. The Endura Fixture is a surface & wall mounted LED batten with extruded aluminium housing and robust construction . PF>.95, System Wattage LED 1x180W with Minium 1500 lumens in 5700k. The Fixture should be of Makes :-BAJAJ(BATTON 112182 BLRB-DB218+ TUBE LIGHT 112432 BLRB 1x18W CWC )/PHILIPS /GE/OSRAM/CGL NS-4

SITC Surface Mounted Bracket/wall light . The Fixture should be Made of chrome&metal Housing.PF>.95, System Wattage Tronto E27,24Ww with Minium 1500 lumens in 5700k. The Fixture should be of Makes :-PHILIPS: 45617/17 Vasa (915004400401) /GE/ OSRAM/ BAJAJ/CGL /WIPRO NS-5

SITC 45W LED Street Light. The Fixture should be Made of pressure diecast housing with TOUGHNED GLASS diffuser and indivisual LEDs with secondary optics with IP 66 protection. PF>.95, System Wattage LED 45W with Minium 1500 lumens in 5700k. The Fixture should be of Makes :-BAJAJ EDGE (169799 BRTFG 45W LED) /PHILIPS BRP409 LED 040 CW HO MR FG S1 PSU GR/CGL LSTP-45 CDL /GE/OSRAM/WIPRO NS-6

Supply of energy efficient AC ceiling fan with 5star rating complete in all respect of approved quality by the Engineer on charge of work. Make Havell's, Orient, Khaitan. Ceiling Fan 48" (a) NS - 7

S/E of heavy duty industrial type of Exhaust fan 900 RPM including the cost of making hole in the wall or providing and fixing MS Sheet 14 SWG with painting as per satisfaction of engineer-in charge. (Commercial / industrial model only).Make: Havell's,Orient,KhaitanSize 300mm sweep, 900 RPM NS - 8

SITC 6W LED aesthetically brillient surface picture/mirror light. The Fixture comprises of aluminium with silver/gold finish . PF>.95, System Wattage LED 6W with Minium 1500 lumens in 5700k of size 70x87x350mm. The Fixture should be of Makes :-PHILIPS(Code 919215850143)/BAJAJ/GE/ OSRAM/ CGL etc. NS - 10

SITC of LED Surface Mounted Square Bulkhead Light. The Fixture should be Made of PDC Housing.PF>.95, System Wattage 6w with Minium 1500 lumens in 5700k. The Fixture should be of Makes :-PHILIPS (WT202WLED6SNWPSUS2PC) / GE/OSRAM/Bajaj NS - 11

Supply and erection of sheet metal 4Way double door Power distribution board T.P.& N. (Vertical Design) dust protected provided with copper bus-bar duly tinned 250 Amp with provision of incomer MCCB upto 250 Amp. The MCCB distribution board shall be including connections with suitable size of thimbles and bonding to existing earth etc. (Cost of MCCB's and MCB's are excluded) Make:- Indo Asian HSN Code-8537. NS-12

24Port LAN Switch D-Link DES-1024C-24 Port 10/100Mbps Unmanaged Ethernet Switch(AOR based On Line Price) NS-13

EATON 3 KVA / 2.4KW Online UPS Model 9145 3Kin-XL Single Phase Input and Single Phase Output with VRLA Battery (Each UPS with 8 No. 12 V, 42 Ah = 4032 VAH to provide approx.60 min. back-up on 3 KVA / 2.4 KW Load) & Battery Cabinet alongwith interlinks. Make: APC, Emerson, Microtek, Pegasus - AAL. NS-14

Supply Installation Testing & Commissioning of 2 MP Full HD WDR IR Vandal Dome Camera - Image Sensor 1/2.8” 2MP Progressive scan CMOS Minimum Illumination 0.006Lux/F1.4( Color,1/3s,30IRE) 0.05Lux/F1.4(Color,1/30s,30IRE) 0Lux/F1.4(IR on), Effective Pixels 1920(H) x 1080(V), Shutter Speed Auto/Manual, 1/3~1/100000s,Video Compression H.265+/H.265/H.264+/H.264, S/N Ratio More than 50dB, Back Light Comp. BLC / HLC / WDR(120dB), Video Streaming 1080P (1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps), Digital Zoom 16x, Ethernet RJ-45 (10/100Base-T), User Account 20 Users, Smart Phone Phone, iPad, Android Phone, IR Range of 30 Mtr., Micro SD, Max 128GB. Make: CPPLUS/ Dahua/ Hikvision. NS - 15

Supply Installation Testing & Commissioning of 2MP Full HD WDR IR Network Bullet Camera - Image Sensor 1/2.8” 2MP PS CMOS, Minimum Illumination 0.006Lux/F1.4( Color,1/3s,30IRE) 0.05Lux /F1.4(Color,1/30s,30IRE) 0Lux/F1.4(IR on), Effective Pixels 1920(H) x 1080(V), Shutter Speed Auto/Manual, 1/3~1/100000s, Video Compression H.265+/H.265/ H.264+/H.264, S/N Ratio More than 50dB, Back Light Comp. BLC / HLC / WDR(120dB) , Digital Zoom 16x, Ethernet RJ-45 (10/100Base-T) User Account 20 Users, Smart Phone iPhone, iPad, Android Phone IR Range of 60 Mtr., Micro SD, Max 128GB. Make: CP-PLUS/Dahua/ Hikvision. NS - 17

Supply Installation Testing & Commissioning of 16 Ch. H.265 4K Network Video Recorder : Processor Dual-core embedded processor, Operating System Embedded LINUX, IP Camera Input 16 channel, Two-way Talk 1 channel Input, 1 channel Output, RCA, User Interface GUI, Video Output- 1 HDMI, 1 VGA, Compression H.265/H.264, Video Resolution 3840× 2160, 1920× 1080, 1280× 1024, 1280× 720, 1024× 768, Alarm Input 4 Channel, Low Level Effective, Green Terminal Interface Alarm Output 2 Channel, NO/NC Programmable, Green Terminal Interface, Hard Disk 2 SATA III ports, up to 12TB, Smart Phone iPhone, iPad, Android Phone, Max User Account 128 users, Ethernet 1 RJ-45 port (10/100M/1000M), 1 Independent 1000Mbps Ethernet Port. Make: CPPLUS/Dahua/ Hikvision. NS - 18

Supply of 4TB Hard disk.Make:- Toshiba/Western Digital/Segagte NS - 19

Supply, Installation, Testing and comissioning of 8 port Layer -2 managable Switch with Power on Ethernet (PoE) enabled, with 8 nos. 10/100/1000base Tx PoE port with 2 SFP port, 1 no. dual personality Gbe Port for copper/fiber uplink, 20 Gbps switching capacity, 14.88 MPPS Forwarding performance , maximum power consumption85watt. Make: Cisco/ Juniper/Ericsson. NS - 20

Supply Installation Testing & Commissioning of 6U rack for switch Mounting with Fan and power Strip, PDU, Hardware Mounting Kit Make: Comrack/HCL/Valrack. NS - 21

Supply Installation Testing & Commissioning of 12U Equipment Rack with provision for housing all control equipment with front & rear door, Blower for cooling and proper locking arrangements and as per the specifications, complete in all respect upto the entire satisfaction of Engineer - in - Charge of the work. Makes: Valrack /Comrack / HCL NS - 22

Supply Installation Testing & Commissioning of 32" LED Monitor, HDMI Port.Resolution,1920 x 1080 (FHD),Backlight Type-LED(Edge),Viewing Angle Degree-178x178,Life span (hrs)-30,000,Brightness (cd/m2)-200,or better. Make: Sony/Panasonic/Samsung NS - 23

Supply Installation Testing & Commissioning of 3 Core Power Cable 1.5 sqmm. Make: Finolex/Polycab/Havells NS - 24

Providing and fixing of FIRE EXTINGUISHER, ABC Powder type stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. MAKE :- CEASEFIRE, SAFEX, MINIMAX, SAFE GUARD. 4 Kg. Capacity (NS 27)

Providing and fixing of FIRE EXTINGUISHER, ABC Powder type stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. MAKE :- CEASEFIRE, SAFEX, MINIMAX, SAFE GUARD. 6 Kg. Capacity (NS 28)

Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per manufactures Specification. ISI Mark complete in all respect. MAKE :- CEASEFIRE, SAFEX, MINIMAX, SAFE GUARD 3 Kg. Capacity (NS 29)

Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. MAKE :- CEASEFIRE, SAFEX, MINIMAX, SAFE GUARD 4.5 Kg. Capacity (NS 30)

Harshit Constructions

SATISH KUMAR GUPTA