ADDN/ ALTN AND RENOVATION OF GUNJAN COMPLEX AND CERTAIN MINOR WORKS AT AFA HYDERABAD

Amount

Demolition of cement concrete or surkhi filling of any description and in any position not otherwise specifically provided for sunken/Roof etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) average 40 mm thick with water proofing compound finished in sunken floor portion etc complete all as specified and directed.

M&L for rendering 15mm thick in CM 1 : 3 on fair faces of brick or concrete surfaces mixed with water proofing compound finished even and smooth in sunken portion without using extra cement etc complete as specified and as directed.

M & L for water proofing treatment to sunken slabs as under complete all as specified and as directed:- (i) Preparation and cleaning of the existing sunken/owered portion of RCC slab surface for full depth of sunken floor by wire brush. chisel out any mortar sticking the surface. (ii) Applying STP LIMITED SHALIURETHANE BTD-BLACK (Minimum 0.80mm dft) over a priming coat of SHALIURETHANE BTD-BLACK 1:1 RÄTIO primer or equivalent product ofAsian paints /M/s MC Bauchemie/ CIPY/SIKA I Pidilite Dr Fixit Thermax / STP applied as per manufacturers instructions to bottom and full vertical sides of sunken floors (iii) Fill it with water and check for dampness and seepage. Incase the slightest indication of seepage / leekage is noticed, the same shall be rectified by injection grouting to seal all cracks or application of polymer modified mortar STP LIMITED SHALI SBR-LATEX or equivalent of M/s MC Bauchemie/CIPY SIKA / Pidilite Dr Fixit / Asian paints / Thermax / STP admixed with integral WPG or cementitous crystalline waterproofirg compound in the affected area to seal all cracks and mícro cracks if any, and this shall be done by contractor at his own cost. (iv) Apply additional coat of STP LIMITED SHALIURETHANE BTD-BLACK or equivalent of Asian paints / M/s MC Bauchemie / CIPYI SIKA/ Pidilite Dr Fixit / Thermax / STP (v) All junction points of side walls where CI/GI pipes are passing through shall be sealed with epoxy cement mortar

M&L for 40 mm dia GI pipe as spouts in sunken floors, medium grade etc complete all as specified and as directed

M&L for PCC (1:5:10) type E2 using 40mm graded stone aggregate filling and mass concrete complete all as specified and directed.

Providing and carry out expansion joint treatment after proper surface preparation to remove loose mortars, dust, foreign particles from joints, fixing of tightly packed closed cell polyethylene based back up rod or filler board to ensure no gaps or voids exists, mask face edge of the joint using masking tape for neat finish, application of polyurethane or polysulphide sealant (width to depth : 2:1 ratio) and allow it cure for 2 days. Mixing of Two part Epoxy Adhesive using slow speed drill till get homogeneous mix, apply it to prepared joint 1-2mm thick with notched trowel or putty blade, tooled to a smooth finish and finally fixing of Flexible expansion joint (FPO Tape) membrane Dr. Fixit Seal Tape/ Hydrogapshield available in 1mm thickness and 150 mm wide exhibiting superior mechanical properties like, Elongation >500%, Tensile Strength >12N/mm2, Tear Strength >200N above joint followed by another layer of epoxy adhesives as complete as per manufacturer’s specification. Epoxy adhesive shall be applied on outer edges of tape. For joint over end laps, the overlaps surfaces must be clean, wiped and lapped with 100 mm overlap. After application the system should be allowed to cure for 7 days.

Removal of debris (Aggregates) obtained from demolition including loading and unloading to a distance of 5km from the starting point and deposited where directed etc complete all as specified and as directed.

M&L for Removing of plants including roots by dismantling of brick work/PCC/RCC including necessary scaffolding , any type , any location/height( roof, parapet walls near pipes etc) and spraying the affected area with solution of 25ml Glyphosphate (4% content) diluted with 1 litre of water or as per manufacturer's instructions after removing roots from wall slabs for preventing the regrowing and making good the disturbed portion using PCC 1:2:4 type B-0 with 12.5mm graded aggregate and plaster in CM 1:3 (Size of the disturbed portion 150X150X150mm) etc complete all as specified and as directed.

Cutting out V groove on cracks of walls and cleaning out, wetting, grouting with crack filler (Dr Fixit or equivalent) mixing with cement slurry, making good the surface by using CM 1:3 or PCC 1:2:4 type B-0 as required at site, as per manufactures instructions, of any description and in any position, with necessary scaffoldings, as approved by Engr in charge

M&L for laying PCC (1:2:4) type B-2 using 40 mm graded aggregate in floors/sub base of 75 mm average thick for etc finished fair and even etc complete all as specified and directed.

Dismantling floor, heath or wall tiling including cement sand mortar bedding and removing rubbish of the premises complete all as specified and directed.

S&F of Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including Screed bed or bedding in layer of mortar 15 mm thick for laying floor finishes in cement plaster 1:4, complete all as specified and directed. complete all as specified and as directed.

M&L for glazed ceramic tiles coloured of size 450 X 350 X6 to7 mm thick as on walls over jointing in neet slurry and pointing in coloured cement to match the inside of tiles including 10mm thick backing plaster in cement mortar (1:3) complete all as specified and directed.

M&L Dark shade/Double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and pointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed or bedding in layer of mortar 15 mm thick for laying floor finishes in cement plaster 1:4, complete all as specified and directed. complete all as specified and directed.

S&F dark shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm (600x600mm), in skirting including 10 mm thick plastering in CM 1:3 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 20 mm thick screed bed or bedding layer in cement mortar (1:6), including pointingin white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for pre-cast reinforced cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate), set in cement mortar 1:4 as in kitchen flat form and shelves in kitchen slabs, landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, with plain faces etc complete all as specified and directed.

M&L for MS TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed.

Taking up or down 15mm bore of pipe PVC/steel tubing and connections, including for refixing or removal etc complete all as specified and directed.

Taking up or down 20mm bore of pipe PVC/steel tubing and connections, including for refixing or removal etc complete all as specified and directed.

S&F of 15 mm bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F of 20 mm bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F in repairs of Vitreous China wash down water closet pan (Pedestal pattern), white including connection to drain and to flushing pipe, and plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device etc complete all as specified and as directed.

S&F in repairs of Vitreous china wash basin, oval type white flat back, of any size excluding taps, waste, chain and plug and porcelain stopper but including brackets etc complete all as specified and directed by Engr -in- charge.

Supply only of Waste coupling of 32 mm chromium plated for glazed ware basins with long screwed shanks and fly-nuts etc complete all as specified and directed.

S&F in repairs of High density polyethylene pipes (HDPE) 40mm dia of pressure rating 6kg/cm2 fixed complete to walls or laid in floors complete all as specified and directed by Engr -in- charge.

S&F in repairs of Pillar taps 15 mm dia, cast copper alloy, Long nose , chromium plated fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and capston head, screwed for iron pipe of 15 mm bore etc complete all as specified and as directed.

S&F in repairs of CP Bib fancy type taps 15mm bore cast copper alloy with capstan head fancy type screwed down screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

S&F in repairs of concealed stop valves 15 mm dia casr copper alloy fancy type chromium plated with long shank and cup screwed down, high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F in repairs of Angle cock of 15 mm dia cast copper alloy with capstan head fancy type chromium plated etc complete all as specified and directed.

S&F in repairs for 125 mm CP shower rose, fancy type with CP arm, all as specified and as directed

S & F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, all as Specified and Directed By Engr-In-Charge.

S&F in repairs of Gun metal globe or gate valves/ Non returning Valve of 20mm dia with iron wheel head screwed both ends for iron pipe etc complete all as specified and directed.

S&F in repairs of Ball valve 20mm dia high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum wt. 210gms) etc complete all as specified and directed.

S&F in repairs of PVC valve less, syphonic action type, flushing cistern, low level, 10 ltr capacity, white, with inlet, ball valve, float and handle including brackets and long flush band etc complete all as specified and directed.

S&F in repairs of PVC connection 15mm size with brass CP nuts of length 600 mm complete all as specified and directed.

S&F in repairs of brass chromium plated towel rack 600mm long "D" type fixed with suitable steel screw etc complete all as specified and directed.

S&F in repairs Soap dish, stainless steel and fixed to wall complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repairs glass corner/ mirror shelves size 300/450 mm of each fixed with necessary screws, bolts , and supporting L type angles with drilling in walls complete all as specified and directed.

S&F in repairs of stainless steel grating 100 mm dia without hole complete all as specified and directed.

S&F in repairs of stainless steel grating 100 mm dia with hole complete all as specified and directed.

S&F in repairs of CP Bib taps two way in one 15 mm cast copper alloy fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by Engr -in- charge.(Make ; Jaguar or equivalent)

S&F in repairs of ABS body CP health faucet complete set including holder stand and one metre PVC pipe, 15 mm cast copper alloy screwed down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by Engr -in- charge. Make : CERA Cat Part No 8030101.

S & F in repairs of Rotational moulded PVC water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) , two layered, hoisted and fixed in position all as specified in SSR part – I including dismantling of OHT of capacity 500 ltrs complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed on walls or in floor complete all as specified and directed.

S&F PVC (SWR) bends any radius suitable for 110mm bore pipe complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed on walls or in floors complete all as specified and directed.

S&F PVC (SWR) bends any radius suitable for 75mm bore pipe complete all as specified and directed.

S&F in repairs PVC (SWR) branch piece single (double Y) with access door equal or unequal 110 mm dia all as specified and directed

Supply and fix 75 mm dia bore PVC (SWR) bends, any radius with oval access door, etc complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) vent cowl, etc complete all as specified and as directed.

S&F in repair of Cast iron Nahani trap of 75mm size with CP grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4), including taking down existing of any description etc complete all as specified.

S&F in repair of Cast iron floor trap of 100 mm size with CP grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4), including taking down existing of any description etc complete all as specified.

Supply and fix in repairs Salt glazed stoneware gully trap, P type 150x100mmmm, including taking down existing of any description etc complete all as specified and as directed.

S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm dia bore of pipe.

S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia bore of pipe.

Taking down Chowkhats or frames with shutters (without taking off shutters) from the frame exc 1.5 sq. m but n exc 4 sq. m complete all as specified and as directed

Taking down Chowkhats or frames with shutters (without taking off shutters) from the frame n.exc 1.5 sq. m complete all as specified and as directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P.brass/ stainless steel screws, all complete as per architectural drawings all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for type of shutters(hung/sliding) of doors, windows, ventilators, including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of aproved make conforming to IS- 733 and IS- 1285, with dash fasteners of required dia and size, including neccessary filling up the gaps at junctions, i.e. at top, bottom ad sides with required EPDM rubber / neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, all complete as per architectural drawings all as specified and directed.

S&F Powder coated (Thickness not less than 50micron) Aluminium anodised Grill, aperture n exc 75 mm ,size 6mm x 4mm thick, including 1 mm thick channel fixed with steel screws complete all as specified and directed.

S&F factory made solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement etc complete all as specified and directed

S&F pressed steel frames (size 105x60mm) for doors with one or more rebates incl necessary fixings lugs, hinges, lock strike plate etc complete all as specified and as directed.

S&F pressed steel frames (size 125x60mm) for doors with one or more rebates incl necessary fixings lugs, hinges, lock strike plate etc complete all as specified and as directed.

M&L for providing plain cement concrete 1:3:6 Type C-0 (using 12.5mm graded stone aggregate) as in filling hollow of pressed steel frame.

S & F 35 mm thick second class hard wood, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S& F 35mm thick glazed and Skelton shutters, open rebated with sash bars, divided in to squares, prepared to receive glass/ gauze etc. edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass/ gauze. Note: glazing/ gauzing will be measured separately

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed.

S&F 150 mm size aluminium alloy handles, fabricated type extruded section, ISI marked all as specified.

S&F of butt hinges, medium weight, cold rolled mild steel of 100 mm long.

Cutting holes in brick work built in cement mortar for inserting hold fast and making good dismantled portion in CM 1:3 depth of cutting exc half brick but n. exc one brick all as specified

M & L for MS flat for hold fast. Conforming to Fe-290 Gde E-165

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate and complete all as specified.

S&F 150 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as specified

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.

M&L preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide/zinc chrome primer complete all as specified and as directed.

M&L for preparation of new or previously untreated surface of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

M&L for hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L 100 mm thick PCC (1:4:8) type D2 (40 mm graded aggregate) as in sub base for floors all as specified and as directed.

M&L PCC (1:1/2:3) type B2 (20 mm graded aggregate) finishing cement concrete surface even and smooth Without using extra cement as in floors all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in ground floors and pavings n exc 15 cm thickness (below or above ground level) any position and disposed off to a distance exc. 50 mtrs and not exc. 250 mtrs all as directed by Engr-in-Charge.

Material and labour 75 mm thick plain cement concrete 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection etc., finished even and smooth without using extra cement complete all as specified and as directed.

M&L for forming Consturction joints 30 mm deep x 10 mm wide, filled with sealing compound Grade B.

M&L for forming Dummy joints 50 mm deep x 10 mm wide, filled with sealing compound Grade B.

S & F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F plates (plain or corrugated) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410(Gde-250)

S&F Mild screw bolts ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 but n exc 10 cm long dia of shank 11 to 15mm.

Taking down plaster in wall/ceilling surfaces on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of Brickwork or stone / boulder / PCC block masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stone-work and precast concrete articles etc complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry of type C1 1:3:6 (using 20mm graded stone aggregate) with solid blocks exc 10cm in width and setting in cement mortar 1:6 etc complete all as specified and as directed.

M&L for half brickwork with sub class 'B' old size bricks, straight or curved on plan, to any radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for plastering in internal wall surfaces of 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for plastering in external wall surfaces of 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 on concrete surfaces as ceilling finished even and smooth (without using extra cement) complete all as specified and directed.

Supply only Liquid water proofing compound.

M & L for two coats of oil bound distemper on newly plastered surface of walls applying 3 mm thick wall care putty and rubbing with sand paper to achieve a level and smooth to wall and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats white wash etc. complete all as specified and directed

M&L for preparation of newly plastered surfaces of external walls and applying two coats cement base paint over a coat of cement primer complete all as specified and directed.

M&L for complete removal of existing treatment of any description and applying 3 mm thick wall care putty and rubbing with sand paper to achieve a level and smooth to wall and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M & L for preparing old plastered or unplastered surfaces on ceilings including cornices and applying one coat of white wash all as specified and directed by Engineer-in-Charge.

M & L for preparing old plastered or unplastered surfaces of walls including cornices and applying one coat of distemper oil emulsion all as specified and directed.

M & L for preparing old plastered or unplastered surfaces on walls/ceiling including cornices and applying one coat of cement based paint all as specified and directed by Engineer-in-Charge.

Taking down carefully un serviceable point wiring of light points, fan, socket out let on TW battens/PVC pipes/casing & caping including material like sockets, switches, ceiling roses, regulators, light fittings etc and removing the materials from site and making good the disturbed portion of walls/floors ceiling etc complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm copper conductor unsheathed, multistranded, PVC insulated, 1100volts grade, single core cable with earth continuity conductor of 1.5 sqmm PVC insulated copper conductor and including rigid PVC Casing Caping of suitable size with accessories fixed/concealed in brick wall/stone wall etc., Including terminal boxes made out of 1.2mm thick MS sheet for switches, fan regulators socket outlet etc along-with 3mm thick top laminated Bakelite sheet for housing switches, sockets, regulators etc for One light point controlled by one one way 5 Amps switch (a) One light point controlled by one switch

(b) one ceiling fan /Exhaust fan point controlled by one 5 Amps switch

(c) one 5 amp point on independent board.

Same as item above but with 2.5 Sqmm multistranded copper conductor wire with 2.5 Sqmm multistranded copper wire as earth continuity conductor in and including PVC conduit (not less than 20 mm) complete all as directed for 15 A socket

S&F Switch socket combination polycorbonate white 2 in 1, 3 pin, 15 Amp flush type universal complete all as specified and as directed.

S&F Switch socket combination polycorbonate white 2 in 1, 3 pin, 5 Amp flush type universal complete all as specified and as directed.

S&F of ceiling rose, three terminal, PVC/polycarbonate, insulated body, ISI marked complete all as specified and as directed.

S&F Switch Piano type polycorbonate white 1 way, 6A, 240Volts complete all as specified and as directed.

S&F LED light fitting 1x10 W 220 V AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose taking down old one complete all as specified and as directed.

S&FLED light fitting 1x20 W 220 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete including taking down old one all as specified and as directed.

M&L for Sub Main wiring with two runs of 1.5 sq mm 1100 V grade (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through and including medium grade, rigid non-metallic PVC conduit / casing & caping (as per site requirement) of suitable size with all necessary fittings, surface in walls/roof/floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth dolly complete and after taking out the existing sub-main wiring etc. complete all as specified and as directed. Note:-(i) Necessary PVC dummy plates & rigid PVC junction boxes for maint./inspection purpose as required on site/directed by Engr-in-charge shall deemed to be included in the quoted rate. (ii) Same size wire shall be used for phase, neutral & earth conductor (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue only for phase, black for neutral and green for earth leads. (iv) Three runs of cable and one run of PVC conduit / casing caping will be measured as one unit.

Supply and fix GI pipe light grade brackets 40 mm dia, 1.5 m long bent to shape as required and fixed with suitable size of 02 Nos MS clamps made out of flat 25mm x 4mm duly drilled with nuts, bolts, washers etc., to poles/walls complete all as directed.

Supply and fix LED Street light fitting 1 X 30 Watt LED pressure die cast aluminium housing heat resistant toughened glass with frame , IP - 66 protection, uniform distribution Make:-Crompton Cat Part No:- LSTO-30-CDL, suitable for 40 mm outer dia G I pipe and connecting up etc.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as directed. Make -Havells -Model Ventilair DX or Equivalent

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated which can provide 75 degrees Celsius water complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. All as directed.

M&L for Sub Main wiring with two runs of 2.5sq mm 1100 V grade (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through and including medium grade, rigid non-metallic PVC conduit / casing & caping (as per site requirement) of suitable sizewith all necessary fittings, surface in walls/roof/floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth dolly complete and after taking out the existing sub-main wiring etc. complete all as specified and as directed. Note:-(i) Necessary PVC dummy plates & rigid PVC junction boxes for maint./inspection purpose as required on site/directed by Engr-in-charge shall deemed to be included in the quoted rate. (ii) Same size wire shall be used for phase, neutral & earth conductor (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue only for phase, black for neutral and green for earth leads. (iv) Three runs of cable and one run of PVC conduit / casing caping will be measured as one unit.

S&F sheet metal enclosure for DBs 2 way complete all as specified and directed. .

Supply & fix MCB SNP 6 to 32 Amps, 'C' curve, 240 volts 10 KA rupturing capacity complete all as directed

Material and Labour for cutting of existing GI pipe line of 25 mm dia for alterations and additions including screwing of GI pipe and providing GI fittings of suitable size and as required at site of work including necessary excavation and earth work complete all as directed

Supply and laying tubes Med grade 20 mm galvanised with all fittings and fixed complete or laid in trenches for connection of existing source

Supply and fix Gun metal gate valve 20 mm dia bore with iron wheel head screwed both ends for iron pipes and complete all as directed.

Supply and fix PP-R Gate valves (brass insert) as per requirement of the site and complete all as directed.

S&F 3-layer PP-R polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. including necessary cutting chesses in stone / brick/ concrete wall and making good with matching colour with the surroundings complete of size 32 mm outer diameter of pipe complete all as specified and as directed.

S&F stop valves/Angle cocks 20 mm dia CP fancy type with capstan head screwed down high pressure screwed both ends for iron pipe for unions of 20 mm etc complete.

S&F PVC connection 15mm size with brass CP nuts of length 450mm etc complete all as specified and as directed.

Material and Labour for cutting of existing GI pipe line of 80 mm dia for alterations and additions including screwing of GI pipe and providing GI fittings of suitable size and as required at site of work including necessary excavation and earth work complete all as directed.

Supply and laying tubes Med grade 50 mm galvanised with all fittings and fixed complete or laid in trenches for connection of existing source all as directed.

Supply and laying tubes Med grade 25 mm galvanised with all fittings and fixed complete or laid in trenches for connection of existing source all as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified

Returning, filling in trenches the excavated soil in layers not exceeding 25cm including watering and well ramming complete all as specified

Removal of excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as directed

Supply and fix Gun metal gate valve 50 mm dia bore with iron wheel head screwed both ends for iron pipes and complete all as directed.

Supply and fix Gun metal gate valve 25 mm dia bore with iron wheel head screwed both ends for iron pipes and complete all as directed.

Supply and fix in repair Bib taps 15 mm, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule including taking down old one complete all as specified and directed by Engineer-in-Charge.

Sadrush Enterprises (BID ID -3346322)

NEWS CONSTRUCTIONS (BID ID -3352965)

SAI RAM CONSTRUCTIONS (BID ID -3351629)

S J REDDY (BID ID -3352486)