Expansion of Tripura Sundari Sub-divisional Hospital, Udaipur, Gomati District, Tripura / Construction of New Hospital building (G plus 4 storeyed)

SUB-HEAD : EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

All kinds of soil

Extra for additional lift of 1.5m or part thereof.

All kinds of soil

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion):

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

SUB-HEAD : CEMENT CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - '-All work upto plinth level:

1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size)

1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size)

Centering shuttering including struttings, propping etc. and removal of form work for:

Foundations, footings, bases for columns.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

SUB-HEAD : RCC WORK

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level:

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits

50 mm thick

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size).

Centering shuttering including struttings, propping etc. and removal of form work for:

Foundations, footings, bases for columns etc. for mass concrete with timber plank

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply

Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply

Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply

Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply

Stairs (excluding landings) except spiral-staircases with wooden plank

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.

Edges of slabs and breaks in floors and walls under 20 cm. wide

Weather shade, Chajjas, corbels etc., including edges.

Smooth finishing of the exposed surface of R.C.C. work with 6mm thick cement mortar 1:3 (1 Cement: 3 fine sand)

Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members.

Providing and fixing in position Stainless steel Grade 304 plate- 1.0 mm thick as per design for expansion joints.

300 mm wide

Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.

All works upto plinth level - Reinforced cement concrete grade M-30

All works upto Floor five level - Reinforced cement concrete grade M-30

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

SUB-HEAD : BRICK WORK

First class brick work in foundation and plinth including cost of all materials as required complete:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Extra for providing & placing in position 2 nos 6mm dia MS bars at every 6th course of full brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:-

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

Extra for providing & placing in position 2 nos 6mm dia MS bars at every 4th course of half brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

SUB-HEAD : WOOD & PVC WORK

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/ Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 150 mm

Frame size 45 x 85 mm

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled or paneled and glazed shutters 25 to 40 mm thick.

Local Teak Wood 16mm. Thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing hard drawn steel wire fabric 75 x 25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62 x 19 mm beading of Gamair wood.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Single rubber stopper

Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge.

Providing 50 × 50 × 50 mm Gamair wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 fine sand) and making good the walls etc.

Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate

based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embrossed on the body / plate with double spring mechanism and door weight upto 125 kg. for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of the Engineer-in-charge:-

With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

Lead Lined doors

Providing and fixing Lead-Lined Hollow Metal Door (Double Leaf, Painted) of size 1800 mm × 2250 mm (approx. 4.05 sqm), manufactured by ISO 9001:2015 certified firm such as Shakti Hormann or equivalent approved make, consisting of door frame, shutter, lead lining, hardware, vision panel, and factory finish, all complete as per manufacturer’s specification and direction of Engineer-in-Charge. 1. Technical Specifications a) Door Frame: Double rebate profile 143 × 57 mm made from 1.6 mm thick galvanized steel sheet (14 gauge), conforming to IS 277. Inside face lined with 1.6 mm thick lead sheet for radiation protection. Factory-fabricated, field-assembled using bolts with back plate brackets and anchor fasteners. Rubber door silencers on strike jambs; frame filled with PUF insulation.

b) Door Leaf: 48 mm thick double-skin flush-type leaf fabricated from 1.2 mm galvanized steel sheet (18 gauge). Full lead lining (1.6 mm thick) inside each shutter. Infilled with honeycomb core and reinforced with steel channels. Interlocked seam edges; factory-prepped for hinges, lockset, and door closer.

c) Vision Panel: 200×300 mm lead glass of 8.5 mm thick radiation-shielding type, with gasket and bead arrangement. d) Finish: Pure Polyester Powder Coated finish (salt spray test ≥ 500 hrs). Colour approved by Engineer-in-Charge. e) Hardware Set (Complete): Heavy-duty SS 304 hinges, lockset, D-handle, door closer, tower bolt, stopper, screws, etc. Equivalent to Dorma/ Hafele/Godrej/Dorset medical series. f) Installation: Supply, transport, handling, anchor fixing, grouting, alignment, sealing, and site adjustment complete.

SS Door for CSSD

SS Door for ICU, CSSD: Providing and fixing Pressed Stainless Steel Hollow Metal Multipurpose Door — Single leaf with vision panel and hardware complete (factory fabricated from ISO 9001 manufacturer, Shakti/Hormann or approved equivalent) as per specification provided. Door clear size : 1250 × 2250 mm. Single rebate SS frame 125 × 60 mm (1.6 mm), mitered & field assembled; shutter 46 mm thick double-skin, shutter faces 1.2 mm SS (18 gauge), resin-bonded honeycomb core, steel stiffeners/pads, factory prepped for hardware; edges interlocked with 1.4 mm bending radius; rubber silencers on strike jamb; frame hollows to be filled with PUF on site; vision panel 200 × 300 mm with 5 mm clear toughened glass (screw-on beading inside); satin stainless finish. Rate includes supply, factory fabrication, protective packing, transport to site, installation, testing & handing over and hardware as per door & hardware schedule.

Providing and fixing Automatic Sliding Hermetic (airtight) Operation Theatre Door having clear opening size 1500 mm × 2100 mm, constructed of stainless steel (SS 304 grade) for both frame and shutter, inner core filled with polyurethane foam or honeycomb structure for soundproofing and insulation, with anti-bacterial and anti-static finish. Door to have hermetic sealing track design, rubber gaskets for air-tight closure, infrared sensors, foot sensor, touchscreen operation panel (inside & outside OT), integration with access control (keypad/biometric), automatic interlocking system, fire-rated version, low-noise (<50 dB) motorized sliding mechanism with manual override, obstacle detection, and anti-pinch safety mechanism. The system shall comply with ISO 14644 (Cleanroom Standards), CE Certification, and other applicable OT safety norms. Integrated lead-lining with vision glass panel (for X-ray shielding) shall be provided as per design requirements.

SUB-HEAD : STEEL WORK

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.

Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete.

Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required.

Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design.

holding down bolts for base plates(20mm dia)

Providing and fixing MS bolts including nuts and washers complete as per standard design:-

Upto 300mm length.

for all connections of runner and purlins(16mm dia)

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing, fabricating, transporting, assembling and erection in position of Steel members for steel colunms, built up beams using structural tubular sections (confirming to IS 2062 -1999 grade B Fe 410, normalized control cooled , yield strength + 250 MPa as per latest IS Code) to the required profile & shape as called for as per the drawing & specifications and of approved make including the shear connectors /studs and fusion weld to top of horizontal member. This item also includes prepration of shop drawings and their approval, necessary templates, adequate temporary supports, scaffolding & staging, all cutting, grinding, sliding & all labour tools, plants & equipments & operations etc. required to complete the job as per drawing & specification.

Every precaution to be taken to prevent rusting of sections. This item also includes all test on materials & welded fabricated parts as per specification and direction of Engineer - in - Charge. Temporary bolts & nuts ( grade EN 8 ) to be used during assembling & shall be removed before site erection. All site erection bolts shall be HSFG type only. The item to include cost of sand blasting on materials, application of primer and epoxy paint in internal & external in fabrication shop & final painting on site including all touch up works after erection as per technical specification.

Scope of work includes: i) Design & fabrication of any additional temporary structure including all type of lifting brackets, supporting brackets ,which will be required for transportion & erection in position / launching of fabrication part or complete element in position. ii) Making provision & arrangement for required opening / inserts for fixing lights fixtures & funning cable conduits. iii) All incidentials labour, equipement & plants required to execute & complete the job from fabrication to erection at final position as per drawing, specification & direction of Engineer - in -Charge. iv) Cleaning & removing of all spoil, temporary arrangementa for casting of deck slab/roofing.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-

In grating, frames, guard bar, railing, brackets, gates and similar works, all complete.

SUB-HEAD : ALUMINIUM WORK & STRUCTURAL GLAZING

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer­in­charge. (Glazing and paneling and dash fasteners to be paid for separately) :-

For fixed portion of approved quality:-

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-

With float glass panes of 8.0 mm thickness ( weight not less than 20.0 kg / sqm )

With float glass panes of 5.5 mm thickness ( weight not less than 13.50 kg / sqm )

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embrossed on the body / plate with double spring mechanism and door weight upto 125 kg. for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of the Engineer-in-charge:-

With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:-

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-

Anodised aluminium of grade AC 15.

Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. complete as per direction of Engineer-in-charge.

Providing and fixing SS Mosquito mesh in anodised (anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodising must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) aluminium shutter fixed in sliding/openable/fixed windows conforming to IS: 1948-1961 as per drawing and directed by Engineer-in-charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.

The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing 6mm thick Suede Finish Exterior Grade High Pressure Compact Laminates (HPL Cladding) such as Greenlam Clads / Rehau / Exidec / Trespa / Fundermax, conforming to EN 438-6:2016 (EDF Grade), size 1300 × 3050 mm, made from urea-free thermosetting phenolic resin-treated kraft papers and amino plastic resin-treated décor papers with UV protective films on both sides. Clads shall comply with EN 13501-1:2007 (Fire Rating Bs1d0), Halogen-free, Antibacterial & Antifungal (JIS Z2801:2010 / ASTM G21-2015), Anti-graffiti, UV-Resistant, Weather-resistant, and CE certified as per EN 438-7:2005 Annex ZA, System-1. Clads to be installed on aluminium tubular substructure (50×25×1.8 mm) placed vertically @ 450 mm c/c, fixed with dead load and wind load brackets using 10 mm anchor fasteners, and 5 mm colour-matching rivets. Maintain 6 mm horizontal and vertical joints between panels. All complete as per manufacturer specifications and direction of Engineer-in-charge.

SUB-HEAD : FLOORING AND SKIRTING WORK

Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips [40mm wide and 4 mm thick] etc. all complete as per direction of Engineer-in-charge.

40 mm thick with 20 mm stone aggregate

Extra for making chequers of approved pattern in Cement Concrete floors, steps, landing, pavements etc. complete.

Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.

600 mm X 300 mm in all shades and design

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.

Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid)

Size of tile 1200 mm x 600 mm x 10 mm (min.) thick

Size of tile 600 mm x 600 mm

Providing and fixing Silver Tactile Stainless Steel SS 316, stain matte finish of standardized designs [Mix of Tactile Studs (Button Type) & Tactile Directional Strips (300x35x5 mm approx.)] conforming to RNIB (The Royal National Institute for the Blind, UK), DETR (Department of the Environment, Transport and the Regions, UK) & ADA (Americans with Disabilities Act, USA) in floors, specially designed to assist the visually impaired - “foot braille” all complete as per direction of Engineer-in-charge.

Providing and laying 1st class quality vitrified tiles at skirting in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. all complete as per direction of the Engineer-in-charge

Glazed Vitrified Tiles - Full Body (Glossy)

Size of tile 1200 mm x 150 mm x 10 mm (min.) thick

Providing and laying 1st class quality vitrified tiles at dado in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. all complete as per direction of the Engineer-in-charge

Glazed Vitrified Tiles - Full Body (Glossy)

Size of tile 600 mm x 600 mm x 10 mm (min.) thick

Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge.

In dark shade using ordinary cement

Providing and laying Mirror Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab.

Providing and laying Mirror Polished Granite stone flooring in treads of steps & risers and skirting in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab (using single length upto 2.00m).

Providing edge moulding to approved thickness granite stone counters, vanities, treads of steps etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge. i) 14 mm thick Granite work

Providing and fixing machine cut, mirror/ eggshell polished , Granite stone cladding in lift lobby/dado/passage, in required design and pattern wherever required of size 600 x 1200 mm, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 fine sand) laid with stainless steel fasteners cleats etc. and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab

Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

14 mm thick Granite of any colour and shade duly approved:-

Area of slab over 0.50 sqm.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and approved thickness fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):-

Granite of any colour and shade duly approved of 14 mm thick (75 x 50 cm).

Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. [The window sills shall be laid in stepped manner with external sill level lower than internal sill level: No seperate payment shall be considered for stepped sill laying]

Granite of any colour and shade duly approved of 14 mm thick

Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.

Kota stone slab 25mm thick

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1 : 3 ( 1 cement : 3 fine sand ) and joined with ordinary cement slurry mixed with pigment to match the shade of slabs, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.

Providing and fixing approved colour homogeneous 1 mm thick wall covering capila of Tusker Vinyl in roll form over wall with approved adhesive, all joints to be soldered by PVC rods as per manufacturers specification etc. complete as per direction of Engineer-in-Charge including proper levels and cleaning.

Providing and laying 2mm thick antifungal self levelling Epoxy flooring on concrete substrate including covering at floor wall junction & including necessary surface preparation using cleaning, dedusting, levelling with cement mortar 1:4 (1 cement : 4 fine sand) of required thickness etc., applying suitable primer including Aisle or zone marking in different colours etc. complete as per manufacturers specifications and as directed by Engineer In Charge.

Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.

Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles

300 mm x 300 mm in all shades and designs

SUB-HEAD : ROOFING AND CEILING WORK

Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film

of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thickness

Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimumto avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm:

0.50mm thickness

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified and as per direction of Engineer-in-charge.

2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as specified.

PProviding and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm

and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings etc. complete and as per direction of Engineer-in-charge.

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per direction of Engineer-in-charge.

With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tile confirming to ISO 5 (class 100 ) specifications.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Coupler

(ii) Single equal tee with door - 110 x 110 x 110 mm

(iii) Single equal tee without door - 110 x 110 x 110 mm

(iv) Bend 87.5o - 110mm

(v) Plain shoe - 110 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete.

SUB-HEAD : FINISHING WORK

12 mm cement plaster of mix

In cement mortar 1 : 4 ( 1 cement : 4 fine sand )

In cement mortar 1 : 6 ( 1 cement : 6 fine sand )

15 mm cement plaster on the rough side of single or half brick wall of mix:

Cement mortar 1:6 (1 cement : 6 fine sand)

6 mm cement plaster of mix:

In cement mortar 1 : 3 ( 1 cement : 3 fine sand )

Neat cement punning.

Extra for plastering exterior walls of height more than 10m from GL for every additional height of 3 m or part thereof complete.

Above 10m upto 13m

Above 13m upto 16m

Above 16m upto 19m

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :

New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:

New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Two Coats

Wall painting with premium anti-bacterial acrylic emulsion paint of interior grade, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour over and including priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Two Coats

Finishing with Epoxy paint ( two or more coats) of approved brand and manufacture at all locations prepared and applied as per manufacturer's specification including appropriate priming coat, preparation of surface etc. complete [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

On concrete wall / Brick wall

SUB-HEAD:WATER PROOFING WORK

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roof, podium by two component cementitious coating over single component acrylic coating as directed by Engineer-in-Charge and consisting of: a) Surface preparation:Ensure all RCC repair work completion from civil contractors and taking handover. Surface cleaning will be done by means of wire brushing, Chiseling and light surface grinding shall be done if required. Laitance shall be removed and cleaned properly. Substrates must be free of loose aggregate and sharp protrusions. b) Crack treatment: Cracks will be opened in a V shape by making a groove of 20mm wide and 25mm deep. Apply bond coat of SBR latex: Water : Cement (1:4:6). V shape groove feel with polymer modified repair mortar (SBR latex: Water : Cement :Sand = 1:4:10:40) c) Making Angle Fillet: Making Angle Fillet (50 mm x 50 mm) in the junction of roof slab & parapet wall. Apply bond coat of SBR latex: Water : Cement (1:4:6).The junction will be treated by polymer modified mortar (SBR latex: Water : Cement :Sand = 1:4:10:40). d) Bore Packing: (If Required)Wherever applicable after making groove, Grouting the all the pipe line joints with, cementitious general purpose grout (Mix density= 2100-2300 Kg/m³, Compressive strength= 50MPa @28days). Then the area should be treated with the application of Epoxy resin-based putty ( Mix density= 1.55 Kg/ltr., Compressive strength= 50N/mm² @7days, Bond strength> 2.5N/mm², Drying time= 8hrs.) & necessary suitable curing to be taken place.

e) Screed concrete with Integral Waterproof compound f) Primer Coat:The entire substrate will be treated by applying coating of single component acrylic coating as Primer @ 0.6-0.8 kg /m2. g) Mixing & Application of two component cementitious waterproofing coating(Elongation>150%): Mixing:Take a purely clean container. Slowly add the powder to the liquid (2:1 ratio) and mix, using a slow speed drill fitted with a suitable paddle (350-400 rpm).The material should be mixed for 3-4 minutes till we get a homogeneous mix which is free of any lumps. Leave the mix for few minutes & allow the entrapped air to be free. Application: The prepared substrate should be in SSD (Surface saturated dry) condition with water. Please ensure there should not be any standing water in the surface before application of the 1st coat slurry by hard brush. Allow the first coat to dry completely for overnight before applying the second coat. Apply second coat at right angles to the first coat. Apply the mixed material over prepared substrate with specified coverage of 1.3 kgs / Sqm (Coverage may vary depending upon the nature and texture of the substrate) as per manufacturer recommendation.Quartz sand to be sprinkled uniformly over the 2nd coat when it is still in tacky condition.Allow the coating to cure for at least 3 days. h) Protection against external Damages: When the cementitious membrane is cured, the treated floor area to be covered with screed concrete average 50 mm thick and coating (For wall) shall be covered with a layer or protective plaster (6 mm) using cement mortar @ 1:4 admixed with integral waterproofing compound @200 gm per 50kg bag of cement.

SUB-HEAD : MISCELLANEOUS WORKS

Providing and fixing Hand Rail Crash Guard 140 mm × 30 mm, aluminium retainer thickness 2 mm (extruded hollow section) with uPVC snip-feet / top cover 20 mm thick having ABS anti-bacterial cap, fixed with stainless steel screws/anchors and adhesive where required, including cutting to length, end caps, welding/polishing of joints where required, supporting brackets, cleaning, protective packaging removal, finishing and all incidental works complete as per direction of Engineer-in-Charge.

Providing & fixing Corner Guard 15 mm thick with aluminium retainer 2 mm thick and uPVC snip-feet, length 1200 mm – including cutting, fixing, fasteners, finishing, cleaning and all incidental works complete as per direction of Engineer-in-Charge.

Providing, fabricating and installing office furniture of various sizes and shapes such as file board shelves, book shelves, working tables with drawer facilities, small tables, wall paneling/partition walls etc. Specification: Providing, making, and installation of office furniture of different dimensions and configurations (e.g., file board shelf, book shelf, working table with drawer unit, small table, etc.), fabricated at site using 19 mm thick solid boiling water proof (BWP) plywood conforming to IS: 710:2010, of approved make, including necessary carpentry/making charges, cost of approved synthetic resin-based adhesive (Fevicol SH or equivalent), stainless steel screws/nails, edge smoothening, and preparation for lamination. The top and vertical/horizontal surfaces of the furniture shall be finished with 1.0 mm thick laminate/mica (laminate cost to be paid separately under relevant item). Work shall include necessary cutting, fixing, jointing, and edge finishing of ply to shape and size, maintaining proper alignment, and ensuring structural stability including fittings like drawer channels, knobs, handles, hinges, etc. as per direction of the Engineer-in-Charge. Only plan area of 19 mm thick plywood used shall be measured for payment. Make / Brand (Approved): Greenply Industries Ltd.(Green Club 710 / Green Gold / Ecotec Platinum 710), Century Plyboards Ltd. (Century Club Prime / Architect Ply / Bond 710), Kitply Industries Ltd.(Kitply Gold BWP / Marine Gold)

Providing and fixing 1.0 mm thick decorative laminate (mica) for wall paneling/partition walls, etc. Specification: Providing and fixing 1.0 mm thick decorative laminate (mica) of approved texture, shade, and design of premium make such as Greenply / Century Ply / Merino / Formica / Sundek / Durian or equivalent, conforming to IS: 2046 (latest revision), on surfaces such as wall panelling, partition walls, or furniture surfaces, as per approved drawings and specifications. Laminate shall be fixed over properly prepared base (e.g., 19 mm BWP ply or similar substrate) using approved grade synthetic resin adhesive (e.g., Fevicol SH or equivalent), ensuring uniform bond without air bubbles or wrinkles. Work shall include all necessary materials and accessories such as edge finishing, cleaning of surfaces, trimming of laminate edges, fixing paper strips at joints if specified, and required hardware/fasteners. The finished surface should be uniform, level, and free from any undulations or visible joints, complete in all respects as per the direction of the Engineer-in-Charge. Make / Brand (Approved): Greenlam (Greenply) / Century Ply (Starline or equivalent) / Merino / Formica

Supply, installation, and positioning of Stainless Steel 3-Seater Patient Waiting Chair Specification: Providing and placing hospital-grade patient waiting chair of 3-seater capacity, made of high-quality Stainless Steel Grade 304, suitable for indoor public waiting areas. The chair shall consist of three ergonomically contoured seats fabricated from minimum 1.2 mm thick perforated or solid SS sheet with polished finish. The frame and legs shall be constructed from SS 304 tubular pipe of minimum 38 mm outer diameter and 16 SWG (1.6 mm) thickness, with integral armrests and anti-skid floor support bushes or SS plate base for bolting. The entire unit shall be free from sharp edges, burrs, or welding projections and shall have a hairline or mirror polished finish. Minimum load bearing capacity per seat should be 150 kg. Complete as per drawing and direction of Engineer-in-Charge. Make / Brand (Approved): Godrej / Featherlite / Damro / Methodex

Providing and fixing Aluminium Profile-Based Name Boards and Signages Specification: Providing and fixing name boards and directional signages of specified and approved sizes, fabricated using anodized aluminium extruded profile frame of premium quality, with 3 mm thick high-density foam base panel for lettering background. The boards shall carry computer-cut, self-adhesive vinyl letters, symbols, or pictograms (e.g., room names, directions, fire exit signs, etc.) in English and/or local language, as per design and sample approved by the Architect. Signage design shall conform to fire exit and safety norms, including use of photoluminescent or reflective vinyl where specified. Installation shall include all required accessories such as fasteners, spacers, stainless steel screws, and finishing trims to achieve a complete, level, and secure mounting on walls, doors, or ceilings, in alignment with the approved signage plan. The signage system shall be executed strictly as per architectural drawings, fire safety regulations, and the direction of the Engineer-in-Charge, and shall include cleaning and final handover in usable condition. Approved Materials & Makes: Aluminium Profiles: Jindal / Bhoruka / Hindalco or equivalent Vinyl Lettering: 3M / Avery Dennison / LG Hausys or equivalent Foam Base Panel: Alstrong / Eurobond / equivalent Photoluminescent (if required): Jessup / EverGlow / NIPPON or equivalent

Providing and fixing Signage Plate (Size: 300 mm x 100 mm) with anodized aluminium frame, vinyl lettering, and polycarbonate protection Specification: Providing and fixing signage plates of size 300 mm x 100 mm, fabricated using anodized aluminium extruded sections (minimum 1.5 mm thick, natural or brown anodized finish) to form the frame. The internal display surface shall have computer-cut vinyl lettering, symbols, graphics, or directional content as per approved design/drawing, executed using computer-grade, weather-resistant vinyl film of approved brand such as 3M / Avery Dennison / LG Hausys or equivalent. The display surface shall be protected with a clear polycarbonate sheet, minimum 2 mm thick, fixed securely within the aluminium frame to protect against dust, scratches, and tampering. The signage shall be installed on walls, doors, or partitions using suitable fasteners (stainless steel screws, spacers, etc.) ensuring level alignment and firm grip. All materials used shall be of approved make and the signage shall conform to the approved sample, and be completed in all respects including layout, lettering, fitting, fixing, cleaning, and finishing as per the direction of the Engineer-in-Charge. Approved Makes: Aluminium Sections: Jindal / Hindalco / Bhoruka or equivalent Vinyl Film: 3M / Avery Dennison / LG Hausys or equivalent Polycarbonate Sheet: Lexan / Makrolon / Tuffak or equivalent

Providing and fixing in position Signage Board (Bed Number Plate – Size 100mm x125 mm) Specification: Providing, fabricating, and fixing in position signage boards made from extruded aluminium section frame of size suitable to hold the display plate, brown anodized or as approved by the Architect/Engineer-in-Charge. The signage shall display vinyl-cut letters/numbers (e.g., bed number) on one or both sides, covered with clear or matte acrylic sheet of minimum 2 mm thickness for protection. The vinyl lettering/numbering shall be done using approved high-quality, weather-resistant, self-adhesive vinyl film of 3M / Avery Dennison / LG Hausys or equivalent make. The signage shall be mounted on walls/partitions using approved fittings and fixtures (stainless steel screws, spacers, fasteners, etc.) as required to achieve proper alignment and stability. The entire signage system shall match the approved sample submitted to the Architect and shall be executed complete in all respects as per the drawing, specifications, and direction of the Engineer-in-Charge. Approved Makes: Aluminium Frame: Jindal / Hindalco / Bhoruka or equivalent Vinyl Film: 3M / Avery Dennison / LG Hausys or equivalent Acrylic Sheet: A-Cast / Plexiglas / Lucite or equivalent

SUB-HEAD : PLUMBING WORKS

Supply, Installation, Testing, and Commissioning of 2‐Bay Scrub Sink, with Infrared Photo sensor, Digital Timer with user defined Time interval 1, 3, 5 and 10 minutes,1 no. mixture valve and 1 No. solenoid valves along with Manual Option Foot Operated mechanism/ Foot switch. Anti‐splash metal body construction made of Stainless Steel Grade 304 polished finished. The Scrub Sink is provided with front access panel for maintenance and repairs. 1 – Position size 1600 mm long as per directin of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing SS grabbars set for accessible toilets comprising of 4 No. Grabbars as specified: (1NO. wing grabbar +1 NO. Lshaped grabbar + 2NO. straight grabbars=1 typical set) a) Swing grabbar (1NO) Providing a S.S.304 SWING HANDICAP GRABBAR- 700mm and of DIA:32MM and thickness 1.5mm of the roved brand and make. b) L Shaped grabbar (1NO) Providing S.S.304 LSHAPED DISABLED GRABBAR of SIZE-600MM(H)X600MM(D) and 32MM DIA .and thickness 1.5 mm of the approved brand and make. c) Straight grabbar (2NO) Providing S.S. 304 GRAB RAIL (600MM),32MMDIA. and thickness 1.5mm of the approved brand and make.

Providing and fixing White Vitreous China of 'Hindware & Parryware' make or equivalent under counter type Oval wash basin of size 550x 480mm with CI brackets suitable for mounting below granite counter including waste fitting with CP brass bottle trap, angle valve with CP connection etc. complete as specified. [Oval Wash Basin Hindware Model No. 10051 OR consider equivalent make].

Providing and fixing JAQUAR MAKE, PRESSMATIC Taps Model No. 031 Pillarcock Auto closing system etc complete.

Providing & fixing in position 'Jacquar Continental' make CPJet Spray with flexible CP supply pipe, and all other accessories, complete.

Providing & fixing 2-way Bib cock JAQUARMAKE, ORNAMIX Model No. 10041 etc. complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China wash basin of size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required :

Size 600x450x200mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Flexible pipe

32 mm dia

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.

450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.

Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Cupler -110 mm

Single pushfit Coupler -110 mm

Single equal tee without door - 110 x 110 x 110 mm

Single equal tee with door - 110 x 110 x 110 mm

Bend 87.5o - 110mm

Plain Shoe :- - 110mm

Double equal junction of required degree without door - 110 x 110 x 110 mm

Double equal junction of required degree with door - 110 x 110 x 110 mm

Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete.

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand):

100 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.B300:B301

20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

62.50 mm nominal inner dia .Pipes.

75 mm nominal inner dia .Pipes.

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing brass stop cock of approved quality :

15 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

25 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end):

25 mm nominal bore

Vertical

40 mm nominal bore

Vertical

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length

15 mm nominal bore

20 mm nominal bore

45 cm length

15 mm nominal bore

20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:

100 mm diameter

Constructing masonry Chamber 30x30x50 cm, inside , in brick work in cement mortar 1:4 (1 cement :4 fine sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

With Second Class bricks

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms.

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete :

150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design:

150 mm diameter S.W, pipe

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design :

For 500x700 mm size

Supplying and installation of 2 H.P Mono block Pump 50x40 mm Suction and delivery pipe complete fabricated to C.0 base of standard size with holding down bolt with panel board, single phase connection motor and starter to main switch, indicator and earthening etc. complete as per direction of the Engineer-In-Charge (No additional cost for electrification upto main switch will be paid seperately) Measurement to be taken after successful operation of the Pump)

Sub-Head: GRANULAR SUB-BASES (NON-BITUMINOUS) AND CEMENT CONCRETE PAVER BLOCK

Granular Sub-base with Well Graded Material (Table 400.1)

By Mix in Place Method

Construction of granular sub-base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD Technical Specification Clause 401.

For Grading I Material

Water Bound Macadam Sub-Base / Base

WBM Grading - 2

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density 'Grading 2' as per MoRD Technical Specification Clause 405. By Mechanical Means

Water Bound Macadam Sub-Base / Base

WBM Grading 3

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill up the interstices of coarse aggregate, watering and compacting to the required density 'Grading 3' as per MoRD Technical Specification Clause 405. By Mechanical Means

80 mm thick factory made c.c. interlocking paver block of M-35 Grade

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern.

Sub-Head: MECHANICAL WORKS FIRE FIGHTING SYSTEM, LIFT AND HVAC WORKS

OXYGEN SYSTEM

Providing and fitting, fixing Oxygen manifold of size 10 + 10 cylinders of following features: Oxygen manifold, extendable type for the required size of bulk Oxygen cylinders. Manifold shall be suitable to withstand a working pressure of 140 kg/cm2 and shall be tested after installation at 300 kg/cm2 and desired oxygen cylinder pressure. It shall have high pressure copper manifold tail pipes (2 Nos. each) with one end having Brass adapter suitable for oxygen cylinders and other end suitable for manifold non return valves. Manifold shall also have brass non-return valves (2 Nos. each) for individual oxygen cylinders. Manifold middle frame of required size shall be made with circumferential mild steel flat duly powder coated with black colour and along with chain for individual bulk oxygen cylinder.

Providing and fitting, fixing Oxygen emergency minor manifold of size 2 + 2 cylinders having following features : Separate bank consisting of required No. of cylinders which will be connected to the main line through regulators after isolating the control panel to ensure uninterrupted supply of medical oxygen in case of manifold / control panel is inoperative. The regulators will have gauges to show status or standby cylinders and delivered line pressure and have safety valve set to blow at pressure above 100 psi.

Providing and fitting, fixing of Control panel for Oxygen 10 + 10 manifold.The panel shall consist of 2 Nos. pressure regulators, one line regulator, 2 high pressure gauges (4" diameter) and one pressure gauge 4" diameter and inter-connecting piping, connecting all these items. Control panel shall give required output (LPM). The electrical circuits shall consist of a step down transformer, 3 Nos. enunciator windows showing' Power On', 'Line Pressure Normal' and 'Reserve in Use'. All these items shall be housed in a metal cabinet made out of MS plate and side wall & top made of MS sheet duly painted with best quality of Epoxy paint. Principles of working: The downstream pressure of both the pressure regulators shall be set at a differential pressure. After opening the cylinder on both the banks, gas shall start flowing through the regulator whose pointer is on duty. Once this bank becomes empty the other bank shall takeover automatically. At this point, turn regulator handle anti clock-wise and bring the pointer on reserve and turn regulator handle (whose pointer is on reserve) clockwise and bring it to duty. Cycle shall be repeated as and when duty bank shall become empty. 1. No interruption of gas supply in case of power failure. 2. Status of each bank is indicated on big pressure gauges. 3. Line pressure is indicated in the small pressure gauge.

Providing and fitting, fixing of high flow Oxygen regulator for emergency minor manifold.

Providing and laying of Copper pipe of different diameters in the Oxygen Sytem:(Medical Grade Copper pipes used shall be half drawn, tampered, seamless, phosphorous deoxidized, non arsenic and degreased. Hardness conforming to BS2871-1971 Part I (Table X) and Chemical composition conforming to BS 6017 of 1981, table 2 of suitable size and gauge

Copper pipe, 10 mm dia.

Copper Pipe, 15 mm dia.

Copper pipe, 28 mm dia.

Copper pipe, 42 mm dia.

Providing and fitting, fixing of isolation valve assembly of different diameters with fittings in the Oxygen system:

Isolation valve assembly with fittings, 10 mm dia

Isolation valve assembly with fittings, 15 mm dia

Isolation valve assembly with fittings, 28 mm dia

Providing and fitting, fixing of wall outlets for Oxygen.

MEDICAL AIR SYSTEM

Providng and installation of air compressors Compressor having 36 CFM (Piston displacement, each air compressor having maximum pressure 8.5 cm2/kg, Non lube oil, 100% oil free CMF /seizer free technology, two stage /3 cylinder with 10 HP , 1440 RPM, 3 phase, 415 yolts, induction motor (TEFC model motor), both mounted on base frame, two NRVs, one electrically operated automatic moisture drain valve, inter connecting piping

Providing and erection of 1000 Litres capacity air receiver( code of construction as per 1S 2825, and plate as per IS 226 )with electrically operated auto drain trap.

Providing and fitting, fixing of air filters in set of four nos. each for Aircompression system

Providing and fitting, fixing of air dryer system for Air compression system

Providing and laying of Copper pipe of different diameters in the air system:(Medical Grade Copper pipes used shall be half drawn, tampered, seamless, phosphorous deoxidized, non arsenic and degreased. Hardness conforming to BS2871-1971 Part I (Table X) and Chemical composition conforming to BS 6017 of 1981, table 2 of suitable size and gauge

Copper pipe, 10 mm dia.

Copper pipe, 15 mm dia.

Copper Pipe, 28 mm dia.

Copper pipe, 42 mm dia.

Providing and fitting, fixing of isolation valve assembly of different diameters with fittings in the air system:

Isolation valve assembly with fittings, 10 mm dia

Isolation valve assembly with fittings, 15 mm dia

Isolation valve assembly with fittings, 28 mm dia

Providing and fitting, fixing of wall outlets for air.

Providing and fitting, fixing of output pressure regulator system with 2 regulators with gauges, 4 isolation valves, and inter connecting piping.

VACUUM SYSTEM

Providing and installation of base frame mounted, air cooled 5 HP vacuum pumps, each having piston displacement -21.6 cfm, free air delivery to suction approximately 90% of P.D., maximum working pressure 29% of Hg or 730 mm of Hg, single stage, twin cylinders, fitted with M.I. channel frame complete with V-belt drive, belt guard etc. 5 HP Electric motor , TEFC 440 volts, 3 phase 1-1/2" BSP stainless steel ball valve with PTFE seat & quarter turn open able handle for pump isolation - with Silencers at vacuum pumps discharge end having Vacuum Filter size 2" dia.

Providing and erection of 1000 liters water capacity vacuum receiver made of M.S. material as per IS-226 and code of construction IS-2825 with drain valve.

Providing and laying of Copper pipe of different diameters in the vacuum system.(Medical Grade Copper pipes used shall be half drawn, tampered, seamless, phosphorous deoxidized, non arsenic and degreased. Hardness conforming to BS2871-1971 Part I (Table X) and Chemical composition conforming to BS 6017 of 1981, table 2 of

Copper pipe, 10 mm dia.

Copper pipe, 15 mm dia.

Copper Pipe, 28 mm dia.

Copper pipe, 42 mm dia.

Providing and fitting, fixing of isolation valve assembly of different diameters with fittings in the Vacuum system:

Isolation valve assembly with fittings, 10 mm dia

Isolation valve assembly with fittings, 15 mm dia

Isolation valve assembly with fittings, 28 mm dia

Providing and fitting, fixing wall outlets for vacuum.

NITROUS OXIDE SYSTEM

Providing and fitting, fixing of control panel for N2O 4+4 manifolds.

Providng and fitting, fixing of N2O manifold 4 + 4 cylinder.The Nitrous oxide system will basically be required for the operation theatres and will also consist of 2 banks of 4+4 cylinders, Technical specification similar to oxygen manifold system as described above S.No1

Providing and fitting, fixing N2O emergency minor manifold of 1 + 1 cylinder.A separate bank consisting of required cylinders which shall be connected to the main line through regulators after isolating the control panel to ensure uninterrupted supply of medical oxygen in case of manifold / control panel is inoperative. The regulators shall have gauges to show status or standby cylinders and delivered line pressure and have safety valve set to blow at pressure above 100 psi.

Providing and fitting, fixing of high flow N2O regulator for emergency minor manifold.

Providing and fitting, fixing of wall outlets for N2O

Providing and laying of Copper pipe of different diameters in the N2O system.

Copper pipe, 10 mm dia.

Copper pipe, 15 mm dia.

Copper Pipe, 28 mm dia.

Copper pipe, 42 mm dia.

Providing and fitting, fixing of isolation valve assembly of different diameters with fittings in the N2O system:

Isolation valve assembly with fittings, 10 mm dia

Isolation valve assembly with fittings, 15 mm dia

Isolation valve assembly with fittings, 28 mm dia

Pipeline accessories

Providing and fitting, fixing area alarm electronic control:

For 2 gases-Oxygen & Vacuum.

For 3 gases- Oxygen, N2O & Vacuum.

For 4 gases-Oxygen, N2O, Air & Vacuum.

Providing and fitting, fixing of Oxygen flow meter with humidifier bottle and pipeline adaptor.

Providing and fitting, fixing of ward vacuum unit with regulator,600 ml jar and wall bracket.

Providing and fitting, fixing of theatre suction unit.

Providing and fitting, fixing of coversion kit with 5 m long pipe:

For Oxygen

For Nitrous Oxide

For Air

For Vacuum

Providing and fitting, fixing of ceiling pendants

Providing and fitting, fixing of low pressure pipe for vacuum.

FIRE FIGHTING SYSTEM

Supply,installtion,testing and commissioning of ISI marked Providing & Fittingfixing of CO2 Fire Extinguisher 2 kg capacity Cylinder.

Supply,installtion,testing and commissioning of ISI marked CO2 gas type Fire Extinguisher of of 4.5 kg capacity made from seamless cylinder with control valve,fitted with discharge adopter, complete with initial gas charge, carrying handle and wall mounting bracket etc. as complete as required.

Supply,installtion,testing and commissioning of ISI marked ABC stored pressure type Fire Extinguisher of 6 kg capacity of welded cylinder squeeze lever discharge valve fitted with pressure gauge with initial discharge tube discharge hose and nozzle suspention bracket charged with mono amonium phosphate base ABC powder and pressuirsed with nitrogen gas etc. as complete as required.

Providing & Fitting fixing of Dry Chemical Powder (DCP) Fire Extinguisher 6 kg capacity Cylinder.

Supply,installtion,testing and commissioning of ISI marked Providing & Fittingfixing of AFFF Fire Extinguisher.

SLFTC of M.S. Pipes on surface Supplying, Laying, Fixing, Testing & commissioning of following sizes (NB)of ISI mark heavy class TATA/ JINDAL M.S pipes including cutting threadingwelding etc. and providing all fittings e.g. Elbows. Reducers. Clamps, Hangers, Flanges, Gaskets. Nuts& Bolts cost including providing two coats of synthetic enamel paints of approved shades over a coat of primer. prior to application to primer the surface should be clean for any dirt, rusts, rough substance etc. including painting of legends of both direction arrow asper approval of the project manager.

200 mm dia (wall thickness 6.3 mm)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

40 mm dia

25 mm dia

150 mm dia (underground pipe line..etc)

Providing and fixing internal /external fire hydrant comprising of SS Fire Hydrant Valve 80 mm inlet with single headed with single outlet with control and fitted with63mm dia instantaneous female coupling on the outlet complete with orifice flange as required, blankcap and chain locations as per drawings (inlet flanges to I.S 5290-1977 class C.

Supply,installtion,testing and commissioning of electric motor driven automatic pressurization pump (JOCKEY FIRE PUMP)consisting of : (Kirloskar / mather platt make) suitable for discharge of 180 LPM at a total head of 55M. Common base plate fabricated out of MS Channel Suitable pump foundation with vibration damping arrangement by cushy foot or similar mountings as required 180LPM @55m Head.

180 lpm at 56 m Head.

Supply,installtion,testing and commissioning of Electric Motor Driven Fire pumping (Sprinkler pump) set (Kirloskar /Mather platt make)suitable for automatic operation consisting of thefollowing for delivery of 2280 LPM at a total head of 55M so as to ensure aminimum pressure of 3.5kg/sq.cm at highest andfarthest outlet of the specified flow and minimum 5.50kg/sqcm at the pump outlet. Commonbase plate fabricated out of MS channel Suitable pump foundation with vibrationdamping arrangement by cushy foot or similarmountings as required.

2280 LPM @55m Head.

Supply,installtion,testing and commissioning of Diesel Engine Driven Fire pump suitable for automatic operation consisting of the following and Part V-1985 and relevant BISspecifications. i) Horizontal Split casing centrifugal pump suitable for delivery of 2280LPM at a total head of 55M so as to ensure a minimum pressure of 5.50 Kg sq cm at the Suitable cement concrete foundation with vibration damping arrangement and cushy foot mounting as required.

2280 lpm at 55 m Head

Supply,installtion,testing and commissioning of Electric Motor Driven Fire pumping (Hydrant pump) set (Kirloskar/Mather platt make) suitable for automatic operation consisting of the following for delivery of 2280LPM at a total head of 55M so as to ensure a minimum pressure of 3.5kg/sq.cm at highest and farthest outlet of the specified flow and minimum 5.50kg/sqcm at the pump outlet. The pump shall be of horizontal End suction type with cast iron body, bronze impeller and stainless steel shaft directly coupled through a flexible coupling with electric motor. Common base plate fabricated out of MS channel of size 75 x 150mm iv) Suitable pump foundation with vibration damping arrangement by cushy foot or similar mountings as required 1620LPM @55m Head.

Sluice valve 150mm

Providing and fixing butterfly valve confirming to type P.N.1.6 of IS 13095-1991 complete with flanges, bolts, nuts, gasket etc. as per specifications complete in all respect hydraulically tested to 20kg/sqcm.

150 mm dia.

100 mm dia.

80 mm dia.

65 mm dia.

50 mm dia.

Providing and fixing cast iron double flanged horizontal type with gunmetal seat non-return valve confirming to class - I of IS : 5312 including nuts, bolts, 1.5 mm thick compressed asbestos gasket including painting complete.

150 mm dia .

100 mm dia.

65 mm dia.

Providing and fixing standard short size SS branch pipe with gunmetel nozzle 16mm dia outlet with standard male instaneous spring lock type 63 mm dia coupling. Branch pipe and nozzle shall confirm to IS : 903-1985.

Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. forsuitable dia MS pipe connection conforming to IS 904 as required.

4 way - 150 mm dia M.S. Pipe

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories.

Pendent Sprinkler

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith syntheticenamel paint of approved shade as required.

Providing and fixing first aid fire hose reel equipment confirming to IS : 884-1969 with up to date amendments finished with post office red spray paint and complete with following as required : (i) 20mm dia. 36.5 meters long hose tubing of approved make confirming to IS : 5132- 1969 with up to date amendments. (ii) Swinging type hose guide fixing bracket assembly (iii) 25mm dia gate valve (iv) 6mm outlet SS nozzle with shut off valve as required.

Providing and fixing 63 mm dia 15 m long Reinforced Rubber lined (RRL) woven jacketed hose tested to bursting pressure 32 kg/sqcm including gunmetal male and female instantaneous type-coupling approved by fire authority, machine would with G.I wire complete in all respects. Hose shall conform to I.S 636 Type II and coupling to I.S 903-1985 WITH ISI certification.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. asrequired.

Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required.

Providing & fixing of Double Door Hose Box with 12 swg and Fiber glass at front with key case.

Supplying, installation, testing and commissioning of 25 mm ball valve.

Supplying, installation, testing and commissioning of half inch ball valve.

Supplying, installation, testing andcommissioning of foot valve.

150 mm dia.

100 mm dia.

Supplying, installation, testing & commissioning of auto pump controller.

Supplying, installation, testing & commissioning of air release valve mechanism typically used in water or irrigation schemes to ensure that any entrapped air in the water system is automatically released in order to maximize the system performance.

Addressable FDA System 8 Loop Panel

Addressable Manual Call point

Addressable Monitor

AIR CONDITIONING

150 mm dia.

150 mm dia.

100 mm dia.

Supplying, installation, testing & commissioning of auto pump controller.

Supplying, installation, testing & commissioning of air release valve mechanism typically used in water or irrigation schemes to ensure that any entrapped air in the water system is automatically released in order to maximize the system performance.

Addressable FDA System 8 Loop Panel

Addressable Manual Call point

Addressable Monitor

Providing fitting fixing of lighting arrangement with protective measure in/c proving single phase main MCB point at machine room, 3 pin socket & light point with switch in each floor & pit of the lift shaft & the electrical wiring should be provided. Through PVC casing or pipe etc. Complete as per direction of the engineer in charge.

SUB-HEAD:INTERNAL ELECTRIFICATION WORKS

Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required.

Wiring for 2 way controlling light point with 3x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type 2 way switch, cover plate, GI box including necessary connection etc. as required.

Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin etc. as required.

Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin etc. as required.

Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:-

2 X 1.5 + 1 X 1.5 sq mm

2 X 2.5 + 1 X 1.5 sq mm

2 X 4 + 1 X 1.5 sq mm

4 X 4 + 2 X 1.5 sq mm

4 X 6 + 2 X 2.5 sq mm

4 X 10 + 2 X 4 sq mm

4 X 16 + 2 X 6 sq mm

4 X 25 + 2 X 10 sq mm

4 X 35 + 2 X 10 sq mm

Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.

19/20 mm dia

25 mm dia

Supplying and fixing of the following electrical accessories including necessary connection etc. as required.

3mm thick bakelite sheet

Supplying and fixing of the following modular accessories including necessary connection etc. as required.

5 step fan regulator (2M):-

RJ11 telephone socket outlet (1M):-

RJ45 LAN socket outlet (1M):-

Louvers/opaque type LED foot lamp (4M):-

20/25 amps single phase motor starter switch (2M):-

Supply and fixing of 32mm x 6mm GI strip on wall/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals.

Supply and fixing of 32mm x 6 mm Copper strip on walls/ floor of the building for hoizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals.

LIGHTNING ARRESTOR

Suppying installation testing and comissioning of following of ESE (Early Streamer Emission) Materials i/c necessary connection etc as required

OPR-Early Streamer emission (ESE) Lighting protection airterminal should complies with OPR 60 Level II (63 Mtr - 5Mtr Height)

Mounting Mast to hold early streamer emission OPR 60, of robust design with mounting mast of 2 met to couple OPR

Mounting Mast of 3 met with base plate and guy wire

Lightning stroke counter

17.2 mm Copper bonded earth rod 3 met tested with IEC 62561 (Make ABB/ERICO/DEHN)

25 kg bag of Ground Resistance Improvement Compound Fursecem powder

Rod to tape clamp (25 x 3 tape to 17 mm rod) of copper alloy

Inspection pit cover plate with IEC 62561

Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in existing PVC Casing Capping/ conduit in recess/surface including connection etc. as required:-

1 x 70 sq mm PVC Insulated copper conductor cable

Providing earthing system with maintenance free earthing electrode of 50 mm dia & 3 mtr long of dual electrode technology filled with highly conductive compound and back fill compound of 2 nos. 25 kg bag, terminal size 32mmx 6mm including accessories with masonry enclosure of CI cover plate size 12"x 12" having locking arrangement including CC works etc as required:-

Earthing with Copper earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12"x 12" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:-

Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked, BEE 1 star/minimum service value 4.0 m3/min/W) : -

Supplying & installation of 400 mm sweep AC wall mounting fan with plastic blade including connection etc as required:-

Supplying & installation of 400 mm sweep AC padestal fan with plastic blade including connection etc as required:-

Supplying & installation of 450 mm sweep 1400 rpm metalic body exhaust fan including connection etc as required (ISI marked) :-

Supplying & installation of shutter for 380/450 mm sweep metalic body exhaust fan in the existing hole as required:-

Supplying & installation of 300 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) :-

Supplying & installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required:-

Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc as required:

Supplying and fixing of following vertical storage water heater 5 star catagory complete with 15 amps top, connection pipes including necessary connection etc as required.

25 litre storage capacity:-

Supplying and fixing of Surface mounted integrated 35 watt,6500K LED batten luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)(Make- Jaguar HBT-WHT-LKBU4KVS35XC/Havells/Philips)

Supplying and fixing of Surface mounted integrated 40 watt,6500K LED batten luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)Make- Jaguar IIL-WHT-LPRD01X040XC/Havells/Philips)

Supplying and fixing of Recessed round/Square shaped 24 watt/6500K LED downlight with integral driver with high quality polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)(Make- Jaguar IDL-WHT-LNRO02R024SC/Havells/Philips)

Supplying and fixing of Recessed round/Square shaped 18 watt/6500K LED downlight with integral driver with high quality polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)(Make- Jaguar IDL-WHT-LNRO02R018SC/Havells/Philips)

Supplying and fixing of Recessed round/Square shaped 12 watt/3000K LED ceiling light with integral driver with high quality polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)(Make- Jaguar OWA-GRY-LCEL03R012XW/Havells/Philips)

Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-

120 watt LED street light fixture with integral driver and secondary lens (IP 66):-

120 watt LED flood light fixture with integral driver and secondary lens (IP 66):-

Supplying and fixing of 7 mtr long OCTAGONAL POLES with withstanding capacity of 180 kmph wind speed i/c necessary connection etc as required.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size):-

Centering shuttering including struttings, propping etc. and removal of form work for: Foundations, footings, bases for columns etc. for mass concrete with timber plank:-

Supplying & installation of 900mmx600mmx300mm floor mounted powder coated weather proof outdoor metal cabinet made of 16 gauge MS sheet supported with 4 nos legs made of 40mmx5mm MS angle complete with single door with locking arrangemet as per dirrection of site engineer:-

Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.

(2+10) / 12 way SPN MCB DB (double door):-

6 way horizontal TPN MCB DB (Double door):-

6 way vertical TPN MCB DB suitable for FP MCB incomer (Double door):-

6 way vertical TPN MCB DB suitable for FP MCCB incomer upto 125 amps (Double door):-

8 way vertical TPN MCB DB suitable for FP MCB incomer (Double door):-

8 way vertical TPN MCB DB suitable for FP MCCB incomer upto 125 amps (Double door):-

Supplying, installation, testing & commissioning of powder coated prewired panel board suitable for 415 volts TP MCCB as incomer & outgoing including busbar & connection as required of the following ratings & sizes:-

4 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

6 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

8 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

Supplying and installation of powder coated steel sheet enclosure for 415 volts MCCB (TP/FP) complete with rotary handle and necessary connection etc as required:-

Enclosure suitable for MCCB above 100 amps upto 250 amps:-

Supplying, installation, testing & commissioning of powder coated prewired digital meter module complete with ammeter, voltmeter, phase indicator lamp, control fuses, CTs, in the existing panel board including connection etc. as required:-

Supplying, installation, testing & commissioning of powder coated side cable module (1 pair) in the existing panel board including connection etc. as required suitable for the following sizes and ratings:-

4/6 way outgoing and incomer upto 400 amps :-

8 way outgoing and incomer upto 400 amps :-

Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-

6 to 32 amps SP MCB:-

6 to 32 amps FP MCB:-

40/50/63 amps FP MCB:-

6 to 32 amps TP MCB:-

40/50/63 amps TP MCB:-

Supplying & installation of TP/FP MCCB of following ratings in the existing MCCB enclosure/ panel board including connection etc as required (Ics=100% of Icu with adjustable settings):-

16 to 100 amps TP MCCB, Breaking capacity 16/18KA (Thermal Magnetic):-

16 to 100 amps FP MCCB, Breaking capacity 16/18KA (Thermal Magnetic):-

125 amps TP MCCB, Breaking capacity 25KA (Thermal Magnetic):-

125 amps FP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-

160 amps TP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-

160 amps FP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-

250 amps TP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

250 amps FP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

320 amps FP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

400 amps FP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required

3 core 4 Sq mm

3 core 6 Sq mm

3 core 10 Sq mm

3.5 core 25 Sq mm

3.5 core 35 Sq mm

3.5 core 50 Sq mm

3.5 core 70 Sq mm

3.5 core 95 Sq mm

3.5 core 150 Sq mm

3.5 core 240 Sq mm

Supplying and laying of following sizes XLPE insulated PVC sheathed copper conductor Un-armoured cable including necessary connection etc as required.

3 core 1.5 Sq mm

Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -

Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes : -

Supplying and fixing of thermoplastic cable junction box with connectors suitable for following sizes cable : -

1.5 sqmm - 4 sqmm Cable:-

4 sqmm - 10 sqmm Cable:-

Excavation of earth for cable trench of 800mm depth & 300mm width in all kinds of soil including back filling of cable trench with the excavated soil with 20cm layer of sand, 3.5 nos bricks per metre for protection including ramming, consolidating to the original shape as per dirrection of Site Engineer :-

Drawing of armoured/un-armoured cable with proper saddling etc as required:-

Supplying and fixing of following Cable tray made of hot dip galvanised iron:-

30 mm x 50mm, 2mm thick

54 mm x 100 mm, 2mm thick

105mm x 150mm, 2mm thick

70mm x 300 mm, 2.5 mm thick

70mm x 450 mm, 2.5 mm thick

70mm x 600 mm, 2.5 mm thick

Supplying and fixing of heat shrinkable cable end termination kits of following sizes : -

3.5 core or 4 core 25/35/50 sqmm size:-

3.5 core or 4 core 70/95/120/150 sqmm size:-

3.5 core or 4 core 240/300 sqmm size:-

LT PANEL

Design, fabrication, supply, installation, testing & commissioning of floor mounted indoor type partially type tested panel (IP 43) (manufactured by CPRI approved electrical panel manufacturer) made of 2.0 mm thick CRCA sheet coated with 7 tank chemical treatment process for powder coating finish with 2000 amps Al busbar and 2 nos 2000 amps 4 pole 50 kA microprocessor release EDO type ACB as incomer with O/L, S/C, U/V, O/V protection including phase and trip indicating lamp and digital multifunction meter module display (with V,A,F,PF,kW,kWH,kVA, kVAR, RS 485 with hermonics) & other accessories etc as required connected via 1 no on load change over switch of 1000 amps rating having the following MCCBs for O/L & S/C protection (Ics=100 Icu) with, spreader links and extended rotary handle for MCCBs including protective MCBs for each incoming and outgoing modules etc as required i) 2 nos 200 amps 36 kA thermal magnetic MCCB ii) 3 nos 63 amps 25 kA thermal magnetic MCCB iii) 3 nos 32 amps 25 kA thermal magnetic MCCB (iv) 1 nos 800 amps 4 pole 50 kA microprocessor release MDO type ACB connected via another 800 amps 4 pole 50 kA microprocessor release MDO type ACB as incomer through 800 amps Onload changeover switch including metering modules and other accessories etc as required ( Lauritz Knudsen / Schneider /ABB/ Legrand/Siemens)

DG Set

Supply installation, testing and commissioning of Silent Type Diesel Generator set prime power rating of 500 KVA, 415V alternator , radiator cooled compliant to CPCB-IV+ , Self-excited self-regulated, Class H insulation suitable for continuous operation -overload capacity of 10% for 1 hour for every 12 hours of operation along with AMF Panel with having ATS Function and suitable for 500 kVA for 2 (two) feeders and comprising of the followings:

Diesel Engine:

The engine would be completed with:- Heavy Duty radiator with fan , Dry type Air Filter, Primary & Secondary fuel filter, fuel priming pump, fuel cooler , Lube Oil filter & lube oil pump , electric starting system and battery charging alternator. Management with Engine Control , Engine Monitoring, Engine Protection & Engine Data Management.

Alternator

The alternator would be 415V, air-cooled, SPDP, 3-ø, 50 Hz, 0.8 pf lag, Self-excited self-regulated, Class H insulation, power metering viz. Kw, Kva, P.f, % load etc. 1. Electronic Controller – Engine Control, protection, monitoring and display module- with following salient features: a. A factory fitted module having global standards for controller, Auto/Start/Stop provision ,Event Fault Log. b. Steel fabricated composite base frame , Steel fabricated Diesel Oil Tank, Starting Batteries, Lead-Acid automotive type 24 VDC (dry- uncharged), Silencer. First fill of Lubricating Oil in engine sump. Anti-vibration Mounting for Generator Set. as per direction of Engineer -in- charge, with necessary anti climet protection and all accessories included in DG set scope.

Supplying of Diesel for test and initial run of Genset as per direction of the Site Engineer.

FIRE ALARM AND DETECTION SYSTEM

Two Loop Panel.:-

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

Single pair 2-core 1.5 sqmm

Supplying, installation, testing and commissioning of following ratings online UPS with inbuilt isolation transformer, 50/60Hz (Auto sensing) frequency, P.F range 0.95-0.99, voltage regulation +/-1%, Pure sine wave form, total harmonic distortion < 5% with full load, Noise level 50db at 1m, LED indication for Normal mode/Load on battery/Load on bypass/System fault, Audible alarm for Mains failure, low battery, Overload, fault and Bypass mode complete with M. S Rack for mounting battery bank, Battery inter link cables and all other necessary accessories including connections etc. as required:-

3 kVA, 1 Ph input/1 Ph output Online UPS complete with 9600 VAH Battery bank for minimum 2hrs Backup:-

Supplying and fixing of 2 x 1.5 sqmm Round flexible (FRLS) wire with necessary connection etc as required

Supplying & laying of UTP CAT 6, 305 meters,Core diameter: 0.565mm,OFC,CM,orange

Supplying & laying of 6 core SM mode Fibre optics cable. (Make: Any renouned brand with ISO/IEC-1180, 9/125u, OS2 Outdoor, as per ITU/T 652D. BELLCORE GR 20 / IEC 794-1, Qualifies as per ICEA-640. & BIS certificate that ensures that the product is technically sound)

Supply, installation, testing and installation of Eternity GE 12S [48+2+2] upgrade up to 240 channel EPABX system with necessary connection as required.

Supply and installation of Alcatel T22 Telephone set with rosette box with necessary connection as required.

Please Enable Macros to View BoQ information