Construction of Bank Square Building at Ambala Cantt

Amount

Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete. Note :- The quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravityof concrete under sub-soil water level with quantity of concrete in cumexecuted under sub-soil water. The depth of centre of gravity shall bereckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m andless than 0.05m ignored.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Extra for laying reinforced cement concrete in or under water and/ orliquid mud, including cost of pumping or bailing out water and removing.Note For Item No. 5.31:- The quantity will be calculated by multiplyingthe depth measured from the subsoil water level up to the centre of gravityof the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade

Area of slab upto 0.50 sqm

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of requiredsize and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Two track four panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above4.00 sqm upto 8.00 sqm).

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-incharge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditationbody which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners,all necessary fittings complete, including applying a priming coat of approved steel primer.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 550 mm dia piles

Extra over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid) 550 mm dia piles

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-Incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls,reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @ 0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R- 2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Providing and applying integral crystalline dry shake of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @ 0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry-shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-incharge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 > 45 MPa and adhesive bond strength Class R3 > 1.5 MPa. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage. For patching of tie rod holes, preparing tie rod hole surface and then priming the area with integral crystalline slurry @0.070kg per sqm and while the surface is tacky, repairing and then filling the tie rod holes with crystalline mortar @0.040kg per hole. The crystalline mortar shall be tightly rodded into tie rod holes or packed tightly (For 25x25x25 mm tie rod hole, use 0.040 kg to fill the hole)

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating rinciples of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly RESTILEed glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in-Charge.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & nchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channe of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : 100 mm dia Ductile Iron Class K-7 pipes

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary andadequate anchoring projections on tail length on 138 mm as perstandard drawing and suitable to with stand the bend test andchemical resistance test as per specifications and havingmanufacture’s permanent identification mark to be visible even afterfixing, including fixing in manholes with 30x20x15 cm cementconcrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20 mm nominal size) complete as per design.

Boring/drilling bore well of required dia for casing/ strainer pipe, bysuitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting stratachart/bore log, including hire & running charges of allequipments, tools, plants & machineries required for the job, all complete as per directionof Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia

Supplying, assembling, lowering and fixing in vertical position in borewell, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, asper direction of Engineer -in-charge. 200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading& sizes as per actual requirement, all complete as per direction ofEngineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

WATERPROOFING FOR HORIZONTAL SURFACE WITH HDPE MEMBRANE Providing and laying leed certified complying salt water grade of HDPE with combination of bentonite composite membrane having >500% elongation as per ASTM D412 TypeIV, Puncture resistance (load) 498.2N as per ASTM E154, Hydrostatic resistance >0.7Mpa as per ASTM D5385 & 26mpa tensile. Cleaning of the surface from dust mortar splashes and loosely adhering particles from PCC. Repairing of cracks and honey combing with rich polymer modified mortar i.e. 1: 3 (cement: sand) mortar admixed with SBR Latex or equivalent confirming to ASTM C 1059-86, where consumption @ 20 % by weight of cement over a bond coat of SBR Latex mixed with cement in 1: 1 ratio (1 part SBR Latex mixed with 1 part cement by volume. The waterproofing system must also allow for installation over green or damp surfaces to accelerating the construction process. The bentonite should have capability of expanding up to 8 times than its original thickness to stop water ingress in case of any damage due to construction activity. Termination to be done at minimum 1 mtr above at vertical walls with 10mmX20mm groove, which should be filled with PU sealant with Shore A hardness should be 25 according to ASTM C 661 and movement capability should be +/- 35%, even satisfy ASTM C 920 Type S, Grade NS, Class 35, Use NT, M, A and O•ASTM C 1248 • U.S. Federal Specification TT-S-00230C Class A, Type II•CAN/CGSB 19.13-M87. The application shall be in accordance with the manufacturer's instructions and as per the direction of the Engineer-in-charge. Work should be done by authorized and recommended applicator only by manufacturer.

Providing & Fixing of fixing 4.3mm thick and 2.00 metre width Carpet Rolls having a density of 70 million fibres of nylon 6.6 per M2 firmly anchored into a waterproofing backing and having average recycled contents of 22% by weight . The Carpet must inhibit the growth of Bacteria and Fungi. The Carpet must be ZERO EMISSION Carpet (Emission below detection limit after 28 days in accordance with ISO 16000-9) . Fire Test EN-13501, Appearence Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, sanitized anti-microbial treatment with resilient waterproof backing , anti static requirements. The carpet must carry a seal of approval from British Allergy Foundation for reducing the growth of dust mite populations. the items is complete respect as per specifications.

Providing and laying 12 mm thick laminate wooden flooring ( AC5) with double locking system on 3mm thick foam for noise reduction. Wooden planks having mehlamine impregnated decorative film of HDF density (water & fireresistant) to be laid complete in all respects as per manufacturer's specifications.

Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion made of Aluminum alloy grade 6063. The baffle blade shall be size of 100x 30 x3000mm in powder coated finish of approved shade or wood grain finish. The baffle blade shall be suspended using C-channel/ Slotted U-profile powder coated to black color at an on-center spacing of 100 mm/150mm. The C-Channel/U 40x40x3000mm profile shall be suspended at every 1200mm on-centre using 8mm threaded rod from the structural soffit at every 1200mm intervals using U-profile hanger/C-channel hanger. Multiple lengths of U-profile/C-channel shall be connected using U-profile connector/ C-channel connector. The baffle blades shall be suspended from the C-channel/U-profile carrier bars at the required intervals (100mm) using baffle hangers. Spacing between blades shall be adjusted using the slots in carrier (Ceiling area to be measured for payment).

DOOR CLOSER : Providing and fixing fire rated door closer of makes Dorma's TS 93 / Brition's LCN1460/Marshall MH-DC-S-14016 (3-4) extruded aluminimum body heavy duty 2 hrs fire rated door closer tested from CBRI Roorkee as per IS : 3614 Part -II and BS : 476 Part 20& 22 from CBRI Roorkee along with wooden /glazed / metal fire doors. The door closer shall be of type 3-4, non-handed having back check function, ANSI/BHIMA certified, and comples with EN 1154 for 100000 cycles. The door closer shall have a 10 year mechanical guarranty / warranty from the manufacturer and the same shall be submitted to the Engineer -in-charge.

PANIC BAR:Providing and fixing Stainless steel 304 grade fire rated touch type panic bar from Marshall MH -PB - SS -11001-03/ Dorma PHA 2000-1 PHA 2003/ Von Duprin CX 98 tested in accordance with IS : 3614 Part - II and BS : 476 Part 20 & 22 from CBRI Roorkee for 2 hrs fire rating along with the wooden fire doors as a complete assembly. The manufacturer shall provide a minimum guarantee / warranty for 5 years against any manufacturing defects.

OUTSIDE ACCESS DEVICE (TRIM): Providing and fixing outside access device 304 grade external trim (Latch & Lock) with 3 keys for panic bar of approved make Marshall MH-PB- SS- 11002 SS / Dorma 's PHX 03 / Von Duprin's CX 98 series for wooden /glazed / metal fire doors all complete as per manufacturer's specifications, approved drawing and direction of the Engineer- in- charge. (for all exits / staircases)

DEAD LOCK: Providing and fixing Mortise Dead Lock with 80mm both side key cylinder of Dorma’s 288 Series/Briton’s EL 2010/Marshall’s MH-L-13002 SSS European standard satin stainless finish tested to 100000 cycles of approved make and tested along with the Wooden /glazed / metal fire doors for 2 hrs. fire rating from CBRI Roorkee.

D- TYPE HANDLE: Providing and fixing stainless steel D- Type back to back pull handle of size 300mm long and 22mm dia of make Dorma’s TGDID/Briton’s E series / Marshall’s 304 grade with complete roses and studs for fixing complete as per direction of engineer-in-charge.

TOWER BOLT: Providing and fixing304 grade Stainless Steel exposed Tower Bolt of size 10mm dia rod and 300 mm long Dorma’s 9114306 , Briton’s DAL FBH 6, Marshall’s MS 300 with complete screws.

DOOR STOPPER : Providng & fixing of SS 304 grade foot stamped door stopper .

Extra for providing toughening to glass complete in all respects as per manufacturer's specifications and as per the directions of Engineer-in-charge.

Supply and Fixing of Slim Glass partition of 10mm Toughened Glass using DORMA Alexa System-45 or equivalent Frames clip profile to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using DORMA Alexa BP45 Profiles at Top & Bottom & Alexa fixed frame cleat . The profile size to be 45x25MM to be fixed on to the floor/ ceiling as per the architect design. DORMA Alexa or equivalent H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel Alexa MP45 & BP45 Overpanel Profile to be used. The Alexa profiles shall be suitable for Glass thickness of 10 mm .The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. The work be executed as per manufacturer's specifications and as per the direction of the Engineer-in-charge. Approved Manufacturer: Profiles/Frames: DORMA (Crown) / Schuco / D-Line Glass : Saint Giobain/Asahi/ PIlkington

Supply & Fixing of Glass Door of 10mm toughened glass with DORMA Alexa System-45 or equivalent frames all around the door with complete assembly . Alexa DP45 Door Profile frame of size 45X50mm with seals with DORMA or equivalent Junior Office Hinges (3nos) & Studio Gala Locks (1no) & Studio Gala lever handles in aluminium silver (EV1) finish , Euro profile cylinder and Door closer with slide channel and Hold Open Unit (as per EN 1154) and saddle plate for fixing on the Glass door and necessary seals to be provided all around the door frames. The Alexa profiles shall be suitable for Glass thickness of 10mm .The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. The work be executed as per manufacturer's specifications and as per the direction of the Engineer-in-charge. Approved Manufacturer: Profiles/Frames: DORMA (Crown) / Schuco / D-Line Glass : Saint Giobain/Asahi/ PIlkington

Providing and fixing door lock to frameless glass door shutter complete in all respects as per site requirement and as per directions of the Engineer-in-charge.

Providing and fixing 13.52 mm thick laminated toughened glass in roofing complete in all respects as per architectural drawing and direction of the Engineer-in-charge. (The frame work will be paid separately under the relevant item).

Providing and fixing of toilet cubicles of Merino TITAN STANDARD/Greenlam Sturdo Classique series or approved equivalent in approved Colour and shade made from solid grade compact high pressure laminate as per IS:2046 in 2100 mm height with 12mm thick compact laminate doors, panel plasters, dividers fixed with stainless steel (304 grade) U channels, top rail of stainless steel (304 grade) and other fittings (stainless steel 304 grade) as per manufacturer specifications and directions of EIC.

Cutting groove in cement concrete work in road of size 5mm x 50 mm and filling the same with polysulphide complete in all respects as per directions of the Engineer-in-Charge,.

Providing & fixing FIXING 500 mm INTERNAL DIAMETER CIRCULAR CLEAR INSIDE OPENING CAST IRON MANHOLE COVER AND FRAME INCLUDING CARRIAGE from the stores of the Engineer-in-charge to site of work loading, unloading, including stacking AND SETTING THE same to correct lines and levels IN 1;2 CEMENT SAND MORTAR over manhole etc.

Pipe Sealing Sealing surrounding of pipe by High strength repair mortar using a flowable, single-component, polymer-modified, cementitious repair mortar containing silica fume and a migratory corrosion inhibitor, capable of full depth repairs”. Material, only Required the addition of water, to produce high strength material, which is easy to use with an extended working time for ease of placement, and it make joints watertight which are prone to water attack, permanently.The application shall be in accordance with the manufacturer's instructions and as per the direction of the Engineer-in-charge

OUTSIDE WATERPROOFING FOR HORIZONTAL SURFACE WITH HDPE MEMBRANE Providing and laying leed certified complying salt water grade of HDPE with combination of bentonite composite membrane having >500% elongation as per ASTM D412 TypeIV, Puncture resistance (load) 498.2N as per ASTM E154, Hydrostatic resistance >0.7Mpa as per ASTM D5385 & 26mpa tensile. Cleaning of the surface from dust mortar splashes and loosely adhering particles from PCC. Repairing of cracks and honey combing with rich polymer modified mortar i.e. 1: 3 (cement: sand) mortar admixed with SBR Latex or equivalent confirming to ASTM C 1059-86, where consumption @ 20 % by weight of cement over a bond coat of SBR Latex mixed with cement in 1: 1 ratio (1 part SBR Latex mixed with 1 part cement by volume. The waterproofing system must also allow for installation over green or damp surfaces to accelerating the construction process. The bentonite should have capability of expanding up to 8 times than its original thickness to stop water ingress in case of any damage due to construction activity. Termination to be done at minimum 1 mtr above at vertical walls with 10mmX20mm groove, which should be filled with PU sealant with Shore A hardness should be 25 according to ASTM C 661 and movement capability should be +/- 35%, even satisfy ASTM C 920 Type S, Grade NS, Class 35, Use NT, M, A and O•ASTM C 1248 • U.S. Federal Specification TT-S-00230C Class A, Type II•CAN/CGSB 19.13-M87. The application shall be in accordance with the manufacturer's instructions and as per the direction of the Engineer-in-charge. Work should be done by authorized and recommended applicator only by manufacturer.

PROTECTION SCREED- 20MM Providing and laying protection screed of M20 Grade Where screed must be admixed with Waterproofing Compound at the rate of 200 ml per bag of cement of where Integral compound confirms IS 2645, IS 9103 for working out a smooth finish. The screed shall be laid on top of the non-woven geotextile layer to protect the waterproofing built-up from mechanical damage. The screed shall have a minimum thickness of 25m. The screed shall be cured by ponding for a minimum of 2 days.

OUT SIDE VERTICAL SURFACE WATERPROOFING- TWO COMPONENT SPRAY APPLIED POLYUREA FOR Providing and applying two component spray applied polyurea for vertical walls followed by Surface preparation by mechanical means using hand grinding machines for providing CSP3-CSP4 profile according to International Concrete Repair Institute Guideline No. 03732. Priming of surface with two component high density and high performance epoxy primer coating with excellent bonding on to concrete surface. Product Pot life of epoxy should be 18min, Practical cure- 12hrs, Shore D Hardness-80, Tensile strength should not be less than 55MPa, Bond Strength Greater than cohesive strength of 25 N/mm2 concrete. >1.5 MPa or concrete failure. The application of epoxy primer shall be with lambskin short pile roller. Top layer shall be with Spray Applied Polyurea for 1.5mm thickness with plural gun spray machine. Polyurea should be two component system with elastic and high crack-resistant properties, even at very low temperatures. The mixed product should have the following features and benefits : • Monolithic with no laps, welds or seams, fully bonded system • 100% solid content , Tensile strength > 25MPa , elongation- 380% , shoreA hardness 92, shore D-45, gel time-3sec tack free-7sec. The supply and apply shall be in accordance with the manufacturer's instructions and as per the direction of the Engineer-in-charge. Work shall be carried out by the authorized applicator of company.

OUTSIDE TERMINATION DETAILING Termination of water proofing layer shall be at minimum 300mm above the ground level of waterproofing at vertical walls with 10mmX10mm groove, which should be filled with polyuria along with PU sealant, with Shore A hardness of 25 according to ASTM C 661 and movement capability should be +/- 35%, satisfy ASTM C 920 Type S, Grade NS. Sealing point shall be protected and supported by aluminium 50mm plates (1mm thick) all around the periphery of walls as per drawings. The supply and apply shall be in accordance with the manufacturer's instructions and as per the direction of the Engineer-in-charge. Work shall be carried out by the authorized applicator of company.

PROTECTION DRAIN BOARD Protection need to done with Providing and fixing Drain board of any branded organization as protection board for waterproofing which is high strength one side dimpled structure, light in weight yet flexible strong and resilient. Product should be High Density Polyethylene (HDPE) draining system with 8 mm dimples, which helps in fast and efficient drainage of surplus water and controls soil erosion, protects construction, allows water to drain while reducing water table pressure. It is mainly used for, vertical / horizontal drainage, soil erosion control, and protects the main waterproofing layer

Providing and fixing stainless steel ( Grade 304) gate made of Hollow tubes, channels, plates etc., including fixing the gate welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying, installation, testing & commissiong Automatic Sliding Gate system complete in all respects as per site requirement and direction of Engineer-in-charge.

Wire rack

Motor

Supplying, fabricating and installation of Green wall consisting of MS frame steel structure including vertical wall panel 450 x 150 mm (apprx.) to hold 3 nos. of 150 mm pots, providing for drip irrigation with 12 mm / 16mm suitable irrigation pipe which is to be installed along with the drips for each pot with a filter. Pots would be installed with geotextile fabric filled with engineered soil consisting of cocopeat and vermicompost. 3 Nos. storage tanks with pressure pumps having capacity of 3000 Ltr each shall also be supplied and installed. Suitable plants will be supplied and planted as per client's choice. The rates includes all material and labour etc. complete. - Green Wall

Maintenance of green wall including plants, labour etc. complete for one year It also includes to install backup nursery for plants throughout the year. This backup nursery, its installation including all components are included in the rate or AMC and no additional expenditure will be incurred by the client. Water and electricity will be supplied by the client free of cost. - Green Wall

Providing and fixing Readymade information signs for service areas in stainless steel finish (Grade 304 , 1.5-2mm thk.) with information embossed or cut out with appropriate lettering/Pictograms/ complete as per the attached reference images. Lettering font,size and content subject to final approval of the architect in charge.

SERVICE AREAS-SIZE OF PLATE 6"X6" with rounded edges

FUNCTIONAL AREAS -SIZE OF PLATE 12"x3"

Providing and fixing Room plates on glass/wooden partitions / glass doors as per the approved location. Size of the SS plate(Grade 304 , 1.5-2mm thk.)- 6" x 6" with acrylic black rimming sliding room occupany indicator , lettering to be embossed/etched complete as per the attached image.Font and final design subject to final approval of the architect in charge.

Providing and fixing Directional signage on toughened glass sheet .Content to be displayed using plotter cut lettering on one side of the sheet, with additional taping to achieve a unifrom background . Lettering font,size ,color and content subject to final approval of the architect in charge. Cost to include mounting of glass sheets using SS Studs on masonary wall surface or suspending the sheets using ss rods from the ceiling.

Providing and installing Fire exit sign ceiling hanged, led Emergency with Ni-cd Battery backup capable of emergency backup of 2hr. Complete with hanging accessoires to the satisfaction of Engineer-in-charge.

Providing and installing Color Coded Dustbin DUO made of FRP Size: 406B x H813 xL813mm With Plastic bucket of 60L Each Colors & Graphics to be customized as per the directions of the architect

Providing and installing SS Dustbins with Swing Lid Size: Dia 230mm x Height 460mm Material : SS-202 grade

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and treching the excavation base to a further depth of 30 cm, refilling the excavation earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 part od stacked volume of earth reduction by 20%: one part of stacked volume of sludgs or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as direction, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Supply, stacking and plantation of following trees complete at site: -

Plumeria Alba

Polyalihia Longifolio

Lantana Selowiana

Chukrassia Tabularis

Asparagus Sprangeri

Sterculia Alata

Euphorbia Millie

Jacaranda Nimosaefolia

Durenta Goldiana

Lagerstroemia Rosea

Wadelia Trilobata

Grevillea robusta

Golden Bottle Brush Topiary

Casurina Aquisitifolia

Cassia fistula

Clerodendron Inerme

Raphis Palm

Areca Catechu

Sterculia Alata

Hibiscus rosasinensis

Delonix regia

Ficus Panda

Plumbago Capansis

Hamelia Pentans

Juniprus Chinensis

Pilea CaderII

Royal Palm

Thuja occiventalis

Jasminum sambac

Supply of good earth free from all types of weed roots stones,bajri & malwa etc.

Providing and fixing floor hung/mounted, white vitreous china single piece, water closet with PP soft close seat cover, hinges, accessories set product code CNS-WHT-963NS Size : 370x510x360mm with Control Plate Opal product code JCP-CHR-152415 and single piece slim concealed cistern with wall mounting frame, installation kit & "S"-Type" drain pipe connection set product code JCS-WHT-2400WS & Rack Bolt (Stainless Steel) product code: ZPS-SNS-RB01 complete in all respect as per directions of Engineer-in-Charge. (Make Jaquar)

Providing and fixing white vitreous battery based infrared sensor operated urinal of approx size 480x300x740 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, Sensotronic Sensor Flushing Valve for Urinal with complete fittings (Suitable for Urinal URS-WHT-13255) and Sensor Product code SNR-CHR-51097 including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. (Make Jaquar)

Providing and fixing white vitreous china ware white colour under counter wash hand basin with fixing accessories set product code: FLS-WHT-5701 size 555 x 425 x 195mm shape oval, chair type adjustable brackets, jaquar make waste coupling 32mm size half thread with 130mm height including the cost of cutting granite for WHB including plugs, screws,white cement, complete in all respects. (Make Jaquar)

Providing and fixing hand shower (Health Faucet) with 8mm dia 1.2 meter long flexible tube and wall hook product code : ALD-CHR-573 to wall hung type W.C and make as approved by EIC. (Make Jaquar)

Providing and fixing Bottle Trap (with Internal Partition) 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange product code : ALD-CHR-769L300x190 and make as approved by EIC. (Make Jaquar)

Providing and fixing Angular Stop Cock/ Angle Valve for basin mixer and geyser points product code: CON-CHR-053KN complete in all respects. (Make Jaquar)

Providing and fixing Exposed Part Kit of Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, Wall Flange, Nipple & Spout product code: ORP-CHR-10233KPM (Suitable For Item ALD-233) including Concealed Body for Single Lever wall mounted Basin Mixer with Cartridge Sleeve and protection sleeve cover old, But without Exposed Parts product code: ALD-CHR-233PSO (Make Jaquar)

Providing and fixing long body bib cock with Wall Flange Product Code: CON-CHR-107KN.

Providing and fixing short body bib cock with Wall Flange Product Code: CON-CHR-037KN.

Providing and fixing in position best Indian make vitreous Chinaware channel of size 600mm x 150mm including laying and fixing in cement concrete 1:2:4 complete as required by Engineer-in-charge. White

Providing and fixing C.P. brass liquid soap container of best quality (as required by the Engineer-in-charge).

Supplying, installing, testing and commisioning of PVC mineral filled low noise pipes and fittings, with push fit rubber ring sockets pipes and fittings confirming to EN-12056, with density 1.9gm/cm3. Piping is to be suspended from ceiling level & fixed on ceiling with necessary fittings and cutting the pipe to the required length including short pieces, assorted fittings such as Plug / Plain Tee / Swept Tee with or without door, bends and elbows or any other standard fittings are included in the rate. The pipe should have B1 fire classification according to EN4102 and is hot water resistant up to 95⁰C for short term loading & 90⁰C long term loading and has chemical resitance of pH 2-12 and completly provides sound protection upto 10 dB at a flow rate of 2 LPS and giving water tightness test for all the piping (refer technical specifications for additional details.) The rate shall include chasing of walls, laying of pipes as per standard working procedures. All the internal drainage pipes are to be suspended below the ceiling level and the pipes are to be supported by modular clamps. The rate includes the cost of all types of clamping and no other separate rate shall be given. The supports required for the Pipes should be made up of cold rolled steel of quality DX51 or greater with minimum GSM of 275 or greater and should have universal mounting slot on the front of the rail for accurate positioning of fasteners and system compatible round and long holes on back of the rail the pipe. The pipe clamps should be either split type with EPDM inner rubber lining or should be MSS-SP manufactured with FM approval and UL listing.

DN 75 mm o/d PP mineral filled SWR pipe

DN 110 mm o/d PP mineral filled SWR pipe

Providing and fixing Brass Floor Clean Out plug with suitable insert keys for opening to soil pipe / waste pipe of uPVC pipe as required complete and direction by Engineer-in-charge:

Providing & Fixing Low Noise Multi Floor Trap with minimum 50mm water seal having 3nos of DN 50mm inlets and 1nos of DN 110mm Top inlet and 1nos of DN 75mm outlet. The baffle construction should be air tight under all circumstances. The inspection plug should enable to access the area under the baffle in order to inspect and clean the area. The Floor Trap volume should be in such a way that a maximal discharge capacity is reached. In case not all the inlets are used two PP-blind plugs are added to the Floor Trap. These blind plugs should secure a leakage free sealing of unused connections to the Floor Trap. Make: Poloplast, Wavin Astral (Silencio). 110 x110 mm outlet

Providing and fixing U-PVC pipes for agriculture & water supply pipes conforming to IS 4985:2000 10 kg pressure without specials (cost of special will be excluded fom this rate) into trenches for all depths and laying out the same to correct alignment gradient, level etc. in trenches including all dressing & treimming and cutting of beds & joints holes, supporting the pipes and specials, in correct position in a suitable rigid manner while the same are being jointed complete. 200 mm dia (Finolex/ Supreme/ Prince Make 10 kgf/sqcm pressure)

Cutting, Jointing and fixing unplasticised PVC soil, waste pipes 10 kg pressure with solvent cementing/solvent welding method of permanently jointing plastic pipes using solvent cement, rapid metod of jointing uPVC pipe and testing the sewer lines for leakage and making all leakages and defects complete as per direction of Engineer In-Charge. 200 mm dia uPVC pipe

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) all-round unplasticised PVC pipes 10 kg pressures including bed concrete as per standard design: 200 mm dia uPVC pipe

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) all-round unplasticised PVC pipes 10 kg pressures including bed concrete as per standard design: 200 mm dia uPVC pipe

Cutting, Jointing and fixing D.I class K-7 pipes and specials of various size ranging from 100mm to 200mm lowering them into trenches, laying & jointing with rubber tyton ring joint or with run lead caulked joints, construction of sluice valve, Fire Hydrant chamber etc. complete as per direction of Engineer In-Charge. 100 mm dia Ductile Iron Class K-7 pipes

Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class): Up to 300 mm dia

Providing and fixing C.I Non- return (Reflux) valve Flanged Ends in swing type PN: 1.6 Pressure with Gun Metal seat IS: 5312 of approved quality (screwed end) :: 100 mm dia

Providing and fixing C.I. sluice valves Flanged Ends IS: 14846 Rising spindle PN. 1.6 Pressure (with cap) complete with bolts, nuts, rubber insertions etc. 100 mm dia

Providing and fixing C.I. double orifice kinetic Air valve ISI marked IS: 14845 with floats S.S seat PN: 1.6 pressure flanged ends of approved quality with bolts, nuts, rubber insertions etc. complete. 100 mm dia

Providing, laying, jointing, fixing and testing Galvanized iron/G.I pipe lines and specials tees bends, sockets, elbows and clamps etc., inside building and testing etc., complete including cutting threading Including cost of specials;

15 mm i/d of pipeline;

20 mm i/d of pipeline;

25 mm i/d of pipeline;

32 mm i/d of pipeline;

40 mm i/d of pipeline;

Providing, fixing and jointing Non- Return valves, on G.I. pipe lines laid Outside/ inside buildings complete in all respects. 32mm i/d;

Providing and placing on terrace polyethylene water storage tank, ISI : marked, III layers with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing G.I. Tank nipple AVR/SVW Make complete in all respects. 32mm nominal bore

Providing and fixing in position best Indian make ISI Marked Ball cock 25mm with brass rod, PVC ball complete in all respects.

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick MDF hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing in position M.S. or heavy flat iron Clamps made out of M.S. flat not less than 5 mm of the approved design for fixing PVC pipe to walls complete in all respects including cutting and making good the walls and floors etc. and painting; For 160mm i/d pipes;

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality. Rectangular shape 600x750 mm internal dimensions.

Providing and fixing 25 HP monoblock domestic water pump set 3-Phase 415 volt, Pump Model- KDS-2560 for Clear water application having 100mm suction & 75mm delivery in CI casing, Gland Packed arrangement having CS shaft, CI Impeller, 2900 RPM at head 60 mtr. flow 13 LPS suitable for 50 Hz AC supply, including the cost of foundation, nuts and bolts complete in all respects.

Providing and fixing 1.0 HP monoblock domestic water pump set single -Phase for reverse hot water system with CI casing, Gland Packed arrangement having CS shaft, CI Impeller, including the cost of foundation, nuts and bolts complete in all respects.

Providing and fixing 0.5 HP monoblock domestic water pump set single -Phase for Domestic water tank to hot water tank system with CI casing, Gland Packed arrangement having CS shaft, CI Impeller, including the cost of foundation, nuts and bolts complete in all respects.

Providing and fixing 3000 ltrs. Solar heating system Non-pressurized complete with 3000 ltrs insulated tank, MS angle stand, 30 no's collectors+ makeup tank + heat exchanger in built + electric element 3 nos + temperature guage + hose pipe + hose pipe clamps complete in all respects.

Providing and fixing hose pipe rubber sleev 20mm dia complete in all respects.

Providing and fixing hose pipe 20mm dia with 28 guage aluminium sheet insulation with self taping screw complete in all respects.

Providing , installing , constructing of sewerage treatment plant complete with Civil & machinery work in all respect. Quantity for STP Ltr. Per Day = 32000 LPD Say. 32 KLD required for site.

Providing , installing , constructing of tubewell upto 150 mtr. B.G.L drilling of borehole, electric logging of borehole with electroinic logger, PVC pipe 10kg pressure, clamp, bail plug & well cap, supply & shrounding of pea gravel complete development of tubewell in all respect.

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 A, Isc = 30 kA for 1 second

630 A, Isc = 30 kA for 1 second

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB (but without MCCB) complete etc. as required

63A T0 125 A, 15 KA SC for 1 second

200A T0 25 KA, SC for 1 second

400A T0 25 KA, SC for 1 second

Supplying, installing by suspension on ceiling/along the wall, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos. aluminium bus bars having current density of 130 A/ sq. cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every meter, adopter box and copper flexible for joints, continuous earthing with 2 Nos. aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 A, Isc = 25 kA for 1 second

630 A, Isc = 25 kA for 1 second

Supply, Installation, Testing & Commissioning of long life Maintenance Free Earthing System . The Rod shall be of Copper Bonded Steel with 23.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper and exothermically welded Cu Busbar of 50X6X200mm tested by CPRI capable of bearing fault current of 50kA. Along with earth enhancement compound (jam plus) tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.2 ohm meter. The earth station shall be with Suitable Poly-plastic Pit Cover with lockable arrangement. (for neutral and body 500 kva transformer) including cost of petty material required to complete the job in all respect. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Supply, Installation, Testing & Commissioning of long life Maintenance Free Earthing System. The Rod shall be of Copper Bonded Steel with 14.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper.Along with earth enhancement compound (jam plus) tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.2 ohm meter . The earth station shall be with Suitable Poly-plastic Pit Cover with lockable arrangement. MAKE :- JMV, ERICO, OR FURSE, OBO including cost of petty material required to complete the job in all respect. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Supply erection testing and commissioning of long life Maintenance Free Earthing System. The Rod shall be of Copper Bonded Steel with 17.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper and exothermically welded Cu Busbar of 50X6X200mm tested by CPRI capable of bearing fault current of 25 kA. Along with earth enhancement compound tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.2 ohm meter . The earth station shall be with Suitable Poly-plastic Pit Cover with lockable arrangement. including cost of petty material required to complete the job in all respect. MAKE :- JMV, OBO BATTERMAN OR ERECO.

LIGHTNING CONDUCTOR Supply erection testing and commissioning of single spike air terminals of 10 mm/16 mm dia.of following lengths as required and as per site conditions. the air terminal shall be manufactured with aluminium. The terminal shall be provided with the integrated / attached threaded base support suitable for mounting the terminals as per site condition. The base support shall be minimum 3 mm thick and shall have inbuilt connector fitting for connection of lightning conductor in such away that conductor contact area shall not be less than 40mm on all side of the conductor. The air terminals shall be supplied with the intermediate guy-wire supports to make it stable in case of high wind speed. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO. 1000 mm

Supply erection testing and commissioning of Roof Conductor for Parapet and Interconnection of Air Terminal: Supply of 8 mm dia aluminium round conductor for air termination network at parapet wall with suitable accessories like type of clamps, conductor holder etc. as required and as per specifications. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

Supply erection of T - Connector for making straight joint of 8 mm aluminium Conductor to 8 mm dia aluminium conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

Supply erection OF Cross - Connector for making straight joint of 8 mm aluminium Conductor to 8 mm dia aluminium conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work. including cost of petty material required to complete the job in all respect. Make:JMV, OBO BATTERMAN OR ERECO.

Supply erection of Straight - Connector for making straight joint of 8 mm aluminium Conductor to 8 mm dia aluminium conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

Supply erection of 8 mm dia aluminium round conductor for Down conductors to be installed on vertical façade of mesonery / glass / metalic work, with suitable accessories like type of clamps, conductor holder etc. as required and as per specifications. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

Supply erection of Test Clamp to disconnect the down conductor from the earth termination network for regular checks of the earth termination resistance value. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

Supply erection of Expansion piece of made of 8mm aluminium at every 20 mtr to maintain the flexibility to the conductor due to heat. including cost of petty material required to complete the job in all respect. Make: JMV, OBO BATTERMAN OR ERECO.

PVC Insulated wiring in recessed 1.6 mm thick MS conduit pipe with 1.5 sq.mm PVC Insulated copper conductor cable with modular accessories.

1) Fan Point

Medium Point

Long Point

Light point

Short point

Medium Point

Long point

Twin control light point with 2 ways 5 amp single pole switch

Short point

Medium Point

Long point

Call bell point i/c MS box of size 180mmx100mmx60mm deep for call bell.

Long point

3 pin, 5 amp. Plug point i/c earthing the 3rd pin etc.

Short point

Medium Point

Long Point

3 pin,15amp plug point with 4 sqmm PVC insulated copper conductor cable i/c earthing the 3rd pin etc.

Medium Point

Long Point

Light point without control- Short point.

Light point without control- Medium point.

Light point without control- Long point.

Supply, Installation, Testing & Commissioning of ACB Microprocessor Based release 800A 4P EDO 50KA with OL,S/C,Earth Fault,Instanious,Neutral & Ground fault Protection LSING + Display Confirm IEC 60947/IS 13947 ( Part 1 & 2), Ics=Icu=Icw, Icw value is for 1 Sec. Flexible & Adjustable Current time protection for Over load, Short Circuit, instataneous s/C & Earth Fault with 5 Trip history & inbuilt LED for Fault indiaction for O/L, / S/C & E/F

ACB Microprocessor Based release 1600A 4P EDO 50KA with OL ,S/C,Earth Fault,Instanious,Neutral & Ground fault Protection LSING + Display Confirm IEC 60947/IS 13947 ( Part 1 & 2), Ics=Icu=Icw, Icw value is for 1 Sec. Flexible & Adjustable Current time protection for Over load, Short Circuit, instataneous s/C & Earth Fault with 5 Trip history & inbuilt LED for Fault indiaction for O/L, / S/C & E/F

S/E of XLPE (E) 11 KV HT aluminum conductor armoured cable ISI mark laid in 1 meter below ground level with sand & bricks with all labour and material including digging and refilling of trench, required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. 11KV(E) 3C x 185sqmm XLPE Insulated Al Conductor Arm HT Cable

S/E of XLPE (E) 11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe /trenches/surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. 11KV(E) 3C x 185sqmm XLPE Insulated Al Conductor Arm HT Cable

CAPACITOR PANEL 400KVAR Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14/16 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical interlocking as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 3 mm to be provided throughout the length of the panel. complete with both Electrically interlocking foolproof system. The Panel should be extendable type. (Make of panel, Tricolite, Ambit, International Switchgear, Amco, Kalyani switchgear)l). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008 Note:- The cost of ACBs, MCCBs, MCBs are not included in the panel's cost and will be paid under separate head. All acccessories included in the panel cost such as rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel.

INCOMER FEEDER MCCB 800A. TP 50KA = 1 NOS Spreader Link = 1 NOS Rotary Handle = 1 NOS Voltmeter with VSS = 1 NOS Ammeter with ASS = 1 NOS RYB Indication Lamp LED = 3 NOS 630/5Amp. 15 VA CL-1 Current Transformer = 3 NOS 06Amp. Control SP MCB = 3 NOS CT Short Link = 3 NOS Neutral Link = 1 NOS OUTGOING FEEDER 14 Step APFC Relay = 1 NO Capacitors 400 Kvar Exhaust Fan = 1 NOS Capacitor Bank 10 KVAR = 1No. MCB TP 32A. = 1 NOS Capacitor Duty Contactor 10KVAR = 1 NOS Control MCB 6A. = 1 NOS ON / OFF Indicator = 2 NOS ON /OFF Push Button. = 2 NOS Auto Manual Switch. = 1 NOS Capacitor Bank 15 KVAR = 1Nos. MCB TP 40A. =1 NOS Capacitor Duty Contactor 15KVAR . =1 NOS Control MCB 6A. . =1 NOS ON / OFF Indicator = 2 NOS ON /OFF Push Button. = 2 NOS Auto Manual Switch. = 1 NOS

Capacitor Bank 25 KVAR = 7 Nos. MCB TP 63A. = 7 NOS Capacitor Duty Contactor 25KVAR = 7 NOS Control MCB 6A. = 7 NOS ON / OFF Indicator =14 NOS ON /OFF Push Button. = 14 NOS Auto Manual Switch. = 7 NOS Capacitor Bank 50 KVAR = 4 Nos. MCCB 125A. TP 36KA = 4 NOS Spreader Links = 4 NOS Capacitor Duty Contactor 50KVAR = 4 NOS Control MCB 6A. = 4 NOS ON / OFF Indicator = 8 NOS ON /OFF Push Button. = 8 NOS Auto Manual Switch. = 4 NOS PANEL SIZE:- H2375 X W1500 X D600 ENCLOSURE & ACCESSORIES Fabrication in 1.6mm.CRCA Sheet Powder Coating in Siemens Gray Shade, 75x40mm.Channel Base Frame, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 800A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc.

Design, Manufactaring, Supply, & Commissioning of fully rated electrical grade following given ratings TPN indoor duty aluminum bus duct with PVC heat shriankable sleave insulation, rigidly supported to withstand electro meachnical streeses arising out of short circuit condition totally enclose in dust and vermin proof CRCA sheet steel enclosure with 2 nos. suitable size continuous aluminum earth bars, inspection / ventilation louver set (as specified) LT bus duct / trunking suitable for 3 phase 4 wire, 50 MVA supply system generally confirming to Indian Standard specification, as well as technical specification enclose herewith. Main Bus duct between Transformers, DG Sets and LT switch board with adopter chamber at transformers, DG Sets and switch gear side complete with both side ends and horizontal and vertical bends. Complete with all respect. (Make of BUS DUCT, Tricolite, Ambit, International Switchgear, Amco, Kalyani switchgear)l). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008

Outdoor Package Substation- of 11/0.433 KV, 1000 Kva Design, Engineering, Manufacturing, Testing at Outdoor type package substation with facility for internal lighting, earthing, (Make - ABB,BHEL,Schneider, Siemens, L&T) padlocks etc. with necessary FRTU/RTU for SCADA integration purposes Connection between RMU & transformer shall be using 3 nos. 1C X 95 sq.mm. Aluminium unarmoured (E) XLPE cable and connections from Transformer to LT Panel shall be by Aluminium Busbar. Package substation will have the following equipmentsA HT SWITCHGEAR A.1 Three Way, 11kV, 630Amps 25kA for 1 sec., SF6 insulated Non-Extensible Compact switchgear (Type CCT2) consisting of Two Nos. Fixed Isolator Function & One No. Fixed Vacuum Circuit Breaker in SF6 insulated Stainless steel enclosure with self-powered series trip microprocessor base numerical over current & earth fault relay (IDMTL+Inst.) for protection. RMU-NON-Extensible FBX-C /CCT2 (2 Nos. Isolators - C, 1 No. Vacuum Circuit Breaker - T2) with AL Busbar)-BIL 28/75kV RMU-NON-Extensible FBX-C/CCT2 C FUNCTION Consist of 2 Nos. of Load Break Switch. 1. Operation of LBS2. Cable Switch Rating- 12KV, 630A, 25KA/1 sec. 3. Cable Bushing Rating- 630A, 4. Cable Cover:- As per our standard, 5. Fixed type Capacitive voltage indication 6. ON/OFF/EARTH Switch via MIMIC. 7. Bottom Cable Termination- Suitable up to 1 No. X 3C X 300 sq. mm T2 FUNCTION Type:- 3 position Disconnector and Earthing switch equipped with separate drive unit. T2 equipped with over current time release for transformer protection. 1. Vacuum circuit breaker 12 kV, 630 A, 25kA/1 sec. 2. Operation of breaker –

3. Self Powered Electronic numerical protection relay providing over-current & earth fault protection – Schneider make CSPR or C&S make CSDPR relay 4. Tape Wound protection current transformers (Details During Detailed Engineering) 5. Capacitive voltage indication fixed type. 6. ON, OFF, EARTH indication on the front mimic of the panel. 7. Cable box for termination of cable suitable up to 3 Nos. X 1C X 95 Sq. mm 8. Cable cover standard. 9. Emergency trip push button. 10. Shunt trip Coil - 24V DC Schneider 1 RMU accessories:- Operating Handle. 1 Standard Manometer for SF6 gas pressure indication. 1 Right Angled Cable Boots suitable for 1 Run x 3 C x 300 Sq mm 3 Offer reference No/Rev No PSS – TECHNO-COMMERCIAL OFFER Schneider Electric Infrastructure Limited (the demerged Distribution Undertaking of Areva T&D India Limited) Milestone 87, Vadodara-Halol Highway, Village Kotambi, Post Office, Jarod, Vadodara – 391510, Gujarat Tel : 0091 266 866 4466 www.schneider-infra.in Battery 24V DC, 12Ah & Battery Charger - 5A 1 B TRANSFORMER (Manufactured as per IS 1180 with Efficiency Level - II), TYPE:- Ester Oil Type, Hermitically Sealed. (Make - ABB,BHEL,Schneider, Siemens, CROMPTON ) 1. Ratio- 11KV/433V, 2. Capacity:- 1000 KVA, 3. Vector Group- DYn11,

5. Winding - Copper, 6. Class of Insulation- A, 7. Ambient Temperature- 50 Deg C, 8. Temperature rise in Oil & Winding over ambient- 40 & 45 Deg C 9. Total Losses @ 50% Loading - 2790 W (MAX) 10. Total Losses @ 100% Loading - 7700 W (MAX) 11. %Impedance – 5 % Schneider make 1 Transformer Accessories Oil Temperature Indicator 1 C LT Busbar - Main Busbar are of Aluminium however Copper Flexible are provided between Transformer & LT Incomer Connection along with main busbar 1 1 Voltage Rating- 433V 2 Current Rating - 2000A D LT PANEL D-1 Incoming 1 1600 A, ACB, 4 Poles, Drawout Manual, 50 KA, Microprocessor based release for O/L, S/C & E/F protection (Make - ABB,BHEL,Schneider, Siemens, L&T) 2 On, OFF, TRIP lamps Schneider = 3 3 R/Y/B indicating lamps Schneider =3 4 CTs 1600/5A, AC. CL. 1, 5 VA Precise/Reco/reputed make =3 5 Digital MFM - EM 6400, AC. CL. 1.0 Schneider= 1 APFC Panel- Incomer 1 no MCCB TP Pole 320A Ics= 50kA Thermal magnetic with Double break roto mechanism. Intelligent APFC Relay with 150 kVAr MPP Heavy duty Capacitor with suitable rating of contactors & Short ckt protection device for each banking. Banking of Capacitor should be 12.5 X4 no, 25 X 2no, 50 X 1no

Outdoor Type 2mm thick Galvanised Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP34 degree of protection for Transformer Compartment. The enclosure exterior shall be powder coated with PP based paint. HT & LT compartment will be provided with the door and pad locking arrangement. Transformer Compartment will be provided with Cover.The Compartment illumination lamp with door operated switch shall be provided for HT and LT compartment. Lifting(Bucket) Arrangement shall be provided with each PSS. Schneider 1 G EARTHING - Internal earthing connection by using 50 X 6 Aluminium Strips 1 H HV KIT 1 I LV TROLLEY 1 J COPPER FLEXIBLE

Supply, installation, testing and commissioning of 11kV HT 4 Panel Board (VCB Type) for 11kv Sub Station OEM/OEM Authorized Manufactureres (Make - ABB,BHEL,Schneider, Siemens, L&T) INCOMMER FEEDER: Supply of HT 12KV, 3Phase 50Hz, totally metal clad withdraw able type Vacuum Circuit Breaker panel with Copper bus bar of suitable rating, horizontal isolation type VCB of capacity minimum 630 Amps rated current,Aluminium bus bar as per IEC 62271-100-200.The offered panels shall be tested for IAC level of min. 25kA (ABB/BHEL/Siemens/ Schneider only) for better performance: (i) Mechanical life -30,000 , (ii) Rated Current – 10,000 & (iii) Rated Short Circuit Operations – 100 Makes: OEM / OEM Authorised Manufactureres, ABB/ BHEL/Siemens/ Schneider. Panel and VCB parameters are as below : (i) Rated Voltage level/ PF withstand voltage/ Impulse level:12KV/ 28 kV/ 75 kVp (ii) Continuous current rating: minimum 630A (iii) Short circuit withstand current: minimum 25KA for 1sec. (iv) One no. minimum 630 Amps horizontal draw out type vacuum circuit breaker in 12KV metal clad floor mounting panel complete with following:- (a)Manually & Motor operated(230V,AC,50Hz) spring charged type, manually and electrically open (electrical – 24 VDC) operation type, incorporating mechanical as well as electrical ON/OFF indication "OFF" push button, test/service position limit switches, with minimum 6NO+6NC breaker auxiliary contacts in service position. (b)Epoxy cast wound current transformer (CT),12KV of rati150-75 /1+1A, 5P10/0.5, 15 VA burden with metering and protection core including necessary control wiring (c) Voltage transformer with three nos. 1 phase, 3 limbs connected in star, dual class, 11 KV/V3/110V/V3,Cl. 1.0/0.5, 50 VA with draw able type with automatic safety shutters 50VA burden with primary & secondary fuses.(Confirming related IS specifications).

OUTGOING FEEDER - Supply of HT 12KV, 3Phase 50Hz, totally metal clad withdraw able type Vacuum Circuit Breaker panel with Copper bus bar of suitable rating, horizontal isolation type VCB of capacity minimum 630 Amps rated current, as per IEC 62271-100-200.The offered panels shall be tested for IAC level of 25kA, (ABB/BHEL/Siemens/ Schneider only) for better performance: (i) Mechanical life - 30,000 , (ii) Rated Current – 10,000 & (iii) Rated Short Circuit operations – 100 Makes: OEM / OEM Authorised Manufactureres, ABB/ BHEL/Siemens/ Schneider. Panel and VCB parameters are as below: (i) Rated Voltage level/ PF withstand voltage/ Impulse level:12KV/ 28 kV/ 75 kVp (ii) Continuous current rating: minimum 630A (iii) Short circuit withstand current: minimum 25KA for 3sec. (iv) One no. minimum 630 Amps horizontal draw out type vacuum circuit breaker in 12KV metal clad floor mounting panel complete with following :- (a)Manually & Motor operated(230V,AC,50Hz) spring charged type, manually and electrically open (electrical – 24 VDC) operation type, incorporating mechanical as well as electrical ON/OFF indication "OFF" push button, test/service position limit switches, with minimum 6NO+6NC breaker auxiliary contacts in service position. (b)Epoxy cast wound current transformer (CT),12KV of ratio **/1+1A, 5P10/0.5, 15 VA burden with metering and protection core including necessary control wiring A) Protection arrangements for the breaker shall comprise of the following: i) E/F, O/C, TCS with IEC 103 protocol for communication & drawout type - Numerical Type Siemens (7SJ62)/ ABB (REF)/ Schneider ( P122) (ii) Mater Trip Relay (iii) Aux . Transformer protection relay All the Relays shall belong to a common platform and shall be of single make with Electromechanical Relays in Draw-out casing

Supply, installation, testing & commissioning of eco friendly 3 Nos. X 500kVA Silent D.G. Sets suitable for synchronization, Liquid Cooled, Turbo Charged After Cooled diesel engine make KOEL/Cummins/CAT producing a minimum of 608BHP at 1500 rpm, 0.8 power factor, able to deliver optimum output under NTP Conditions with a provision of 10% temporary overload once in 12 hours of running, directly coupled to 500kVA, 415 Volts AC, Three Phase, 50 Hz, 4 wire, 0.8 power factor lagging, brushless type, synchronous alternator, automatic voltage regulator. The engine and alternator should be fitted on common base frame with AVM Pads. The genset should be complete with all accessories like digital engine controller KG-745 or equivalent, remote monitoring system, Electronic Governor, fuel tank of 990 Liters integrated inside the canopy, standard silencer, 24 Volts electric starting system complete with battery and leads, weather proof acoustic enclosure as per CPCB norms and noise level not exceeding 75 db at a distance of 1 meter.

Supply erection testing and commissioning of LED POST TOP 35WATT (+_1 W ) LED EFFICACY 120 LUMENS / WATT including petty materials required to complete the job in all respect. WIPRO Make , Model :-LP07-431-XXX-57-CL, Havells Cat no. RUBYPT35WLED757PSYMTOPC or Equivalent in Philips / Trilux as approved by the Engineer-in-charge. Warranty 2 years from the Date of invoice.

Supply, installation, testing and commisioning of 60 W LED Flood Light luminaire with system lumen output 5100lm and system efficacy of > 85lm/W. LED Flood Light shall be made up of Die Cast aluminum housing with black epoxy polyester powder coating for long life. The luminaire shall be complete IP66 protection for Optical Compartment and Control Gear Compartment. The LED Flood Light shall have power factor more than 0.95 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Reference Wipro Catalogue No.LF19-711-060-57-XX, Havells Cat no. JETACOMPECTOFL60WLED757LTG or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supplying, installation, testing and commissioning of 25 W LED solar street luminaire of housing made of extruded aluminium and IP65 ingress protection. The all in one integrated solar street lighting system having system lumen output upto 4800 lumens. The luminaire should be having SMD type LEDs with secondary lens / optics suitable for streetlighting application, MPPT charge controller and DC driver and automatic dusk to dawn operation feature. The integrated luminaire should have 50Wp monocrystalline PV module, 12.8V/22Ah LifePo4 battery pack having >/= 12 Hrs of autonomy with full power mode and >/= 48 hrs of autonomy with saving mode, dimension (740X305X140) ± 2% mm with aesthetic and compact design. Integreated PIR sensor is used for detecting the movement and increase the intensity of LEDs. to creat safe & effective lighting environment. including all petty materials required to complete the job in all respect. Wipro Cat. No LR14-361-XXX-65-XX or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of 35 W LED Street Light luminaire with system efficacy of 120lm/W. Light shall be made up of Die Cast aluminum housing . The luminaire shall be complete IP66 protection for Optical Compartment and Control Gear Compartment. Street Light shall have power factor more than 0.95 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Wipro Cat. No LR13-501-XXX-57-XX, Havells Cat no. ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of Led fixture 600mmX600mm 33W+/- 1W Recess mounted with full diffuser with minimum system lumen efficacy of 100lm/W having UGR >19 with APFC constant Current driver for proper driving of LEDs and P.F.>0.95 with THD<10% . including all petty materials required to complete the job in all respect.Wipro Cat. No CRCO10R033HP57UGR or Havells Cat no. VENUSNEOHE2X2R18-42WLED857MODUGR<19 or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of Led Recess mounted downlighter 9W+/- 1W Square LED downlighter fixture with minimum system efficacy 100 lm/W with die cast aluminium housing for better heat dissapation having HET non-yellowing PMMA diffuser.The LED luminaire shall have power factor more than 0.9 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance . including all petty materials required to complete the job in all respect. Wipro Cat. No CRDL11R013HP57,Havells Cat No. INTEGRANEODLR10WLED857S or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of Led Recess mounted downlighter 18W+/- 1W Square LED downlighter fixture with minimum system efficacy 85lm/W with die cast aluminium housing for better heat dissapation having HET non-yellowing PMMA diffuser.The LED luminaire shall have power factor more than 0.9 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Wipro Cat. No CRDL11R023HP57,Havells Cat No. INTEGRANEODLR18WLED857S or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, Installation,comissioning of Recess mounted 26 W+/- 1W round LED downlighter fixture with minimum system efficacy 100 lm/W with die cast aluminium housing for better heat dissapation having HET non-yellowing PMMA diffuser.The LED luminaire shall have power factor more than 0.95 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Wipro Cat. No CRDL11R033HP57, Havells Cat No. INTEGRANEODLR24WLED857S or equivalent make in Philips or Trilux .LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and comissioning of Recess Mounted Linear Led Luminaire 20W+/- 1W fixture with minimum system efficacy 100 lm/W with die cast aluminium housing for better heat dissapation having HET non-yellowing PMMA diffuser.The LED luminaire shall have power factor more than 0.9 with THD less than 20%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Wipro Cat. No LM34-251-XXX-57RMCG1, Havells CAt no. DESTELLO50LR25WLED857SPMMAWH or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply,installation,testing and comissioning of Recess Mounted Linear Led Luminaire 4X1 feet 31W+/- 1W fixture with minimum system efficacy 96 lm/W with die cast aluminium housing for better heat dissapation having HET non-yellowing PMMA diffuser.The LED luminaire shall have power factor more than 0.95 with THD less than 10%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance. including all petty materials required to complete the job in all respect. Wipro Cat. No CRCO13R038HP57G1, Havells Cat No. VENUSNEOHE4X1PLR28-36WLED857MOD or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, testing and commissioning of led fixture 4Ft 20W LED Batten LED Batten with minimum system lumen efficacy of 100lm/W with and P.F.>0.95 with THD<20% having Poly carbonate Diffuser and Aluminium Extrusion housing. including all petty materials required to complete the job in all respect. Cat No :Wipro Cat No. LL20-221-XXX-65AL1, Havells Cat No. LUMILINEPLUSBS20WLED865SPCWH or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply,installation,testing and comissioning of 2Ft 10W Mirror Light LED Batten Model no Batten with minimum system lumen efficacy of 100lm/W with and P.F.>0.95 with THD<20% having Poly carbonate Diffuser and polycarbonate Housing. including all petty materials required to complete the job in all respect. Cat. No :Wipro Cat No. LL20-111-XXX-60-NE3, Havells Cat No. LUMILINEPLUSBS10WLED865SPCWH or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, testing and commissioning of led Strip light for indoor application IP 20 fixture with 5 M/Watt. Wipro Catalogue No.LS06-005-120-WW-50+ LED Driver 25 W (LG40-024), Havells Cat no. FLEXISTRIP5MTRIP2024WLED830S or equivalent make in Philips or Trilux. *LG40-024 driver suitable for one unit suitable for 5 m Spool of LED Strip. *LED Driver LG40-024. including all petty materials required to complete the job in all respect. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of Hanging Decorative light water drop shaped suspended luminaire led lamp extra 20 W. including all petty materials required to complete the job in all respect. Wipro Cat. No LM87-D320-BLGD or equivalent make in Philips or Trilux. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supply, installation, testing and commisioning of 3 NO. Led Track Light 20W+/- 1W fixture with minimum system efficacy 2000 lm/W with die cast aluminium housing for better heat dissapation.The LED luminaire shall have power factor more than 0.9 with THD less than 20%. LED Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No LD57-251-036-40-XX. Havells Cat no. CYLINDROTSS25W857S38DWHT or equivalent make of Philips or Trilux. including cost of * XTS-5100 Single phase 1 mtr track . * SKB520 2 mtr single suspension . * XTS 52 Straight connector . including all petty materials required to complete the job in all respect. LM79 REPORT FROM 'NABL' LAB SHOULD BE SUBMITTED

Supplying, installation, testing and commissioning of A.C. CEILING FAN 48" (1200MM) STAR 220 5 Star Rating including cost of petty material required to complete the job in all respect. ( Make : HAVELLS, CROMPTON, anchar panasonic).

Supplying, installation, testing and commissioning of A.C. CEILING FAN 56" (1400MM) BRIZAIR DOUBLE BALL BEARING including cost of petty material required to complete the job in all respect. ( Make : HAVELLS, CROMPTON, anchar panasonic).

Supply, Installation, Testing and Commissioning, of wall fan 300 mm (ISI mark) including cost of petty material required to complete the job in all respect. (Make Crompton, Havells or anchar panasonic)

Supplying, installation, testing and commissioning of HEAVY DUTY EXHAUST FAN 900 RPM 1PHASE 300MM-12'' including cost of petty material required to complete the job in all respect. ( Make : HAVELLS, CROMPTON, anchar panasonic).

Supplying, installation, testing and commissioning of HEAVY DUTY EXHAUST FAN 900 RPM 1PHASE 380MM-15'' including cost of petty material required to complete the job in all respect. ( Make : HAVELLS, CROMPTON, anchar panasonic).

Panels Supply, Installation, Testing and Commissioning of wall / free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2 mm thick CRCA sheet, required hardware 3 mm thick bakelite sheet provided all along the bus bar and cable tray separating switches compartment and supporting suitable channel duly painted by 2 coat zinc / red oxide primer followed by 2 coats of powder coating in grey or required shade after rising. the panel having PU / Neoprene rubber gasket of not less than 3 mm thickness separate detachable gland plate MS base channel hinged door with inter locking arrangement for equipments / switch wear. Transport acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3 mm thick for separately cable alley to BBC from switch chamber extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra items. Side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. The Panel will be complete with control wiring (Copper) and fuse protection. (Only outer area on all sides shall be measured). (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. tested from the engineer-in-charge / consultant.

Note:- The cost of ACBs, MCCBs, MCBs ,are not included in the panel's cost and will be paid under separate head. All acccessories included in the panel cost such as rotary handles, metering etc. MAIN ELECTRIC PANEL - 125.00 Sqm Incomer Feeder For 1000KVA Transformers =03Nos. ACB 1600A. FP 50KA EDO TYPE MP Based = 3 NOS For D.G 500KVA = 3 NOS ACB 800A. FP 50KA EDO TYPE MP Based = 3 NOS BUS COUPLER ACB 1600A. FP 50KA EDO TYPE MP Based = 2 NOS Multifunction Meter with Communication Port RS485 = 6 NOS RYB Indication Lamp LED =18 NOS 1600 &800/5Amp. 15 VA CL-1 Current Transformer = 18 NOS 06Amp. Control SP MCB = 18 NOS CT Short Link = 6 NOS ELECTRICAL INTERLOCKING Both DG I/C Electrical & Mechanical Interlocking LTPB = 7 NOS UV Release = 7 NOS OUTGOING PROVISAN FOR MCCB 630A. FP 36KA = 10NOS Spreader Links = 10 NOS Rotary Handle = 10 NOS Voltmeter with VSS = 10 NOS Ammeter with ASS = 10 NOS RYB Indication Lamp LED = 30 NOS 630/5Amp. 15 VA CL-1 Current Transformer = 30 NOS 06Amp. Control SP MCB = 30 NOS CT Short Link = 10 NOS

PROVISAN FOR MCCB 500A. FP 36KA = 5 NOS Spreader Links = 5 NOS Rotary Handle = 5 NOS Energy Meter = 5 NOS 400/5Amp. 15 VA CL-1 Current Transformer = 15NOS PROVISAN FOR MCCB 400A. FP 36KA = 12 NOS Spreader Links = 12 NOS Rotary Handle = 12 NOS Energy Meter = 12 NOS 630/5Amp. 15 VA CL-1 Current Transformer = 36 NOS PROVISAN FOR MCCB 300A. FP 36KA = 1 NOS Spreader Links = 1 NOS Rotary Handle = 1 NOS Energy Meter = 1 NOS 630/5Amp. 15 VA CL-1 Current Transformer = 3 NOS PROVISAN FOR MCCB 200A. FP 36KA = 1 NOS Spreader Links = 1 NOS Rotary Handle = 1 NOS Energy Meter = 1 NOS 630/5Amp. 15 VA CL-1 Current Transformer = 3 NOS PROVISAN FOR MCCB 100A. FP 36KA = 1 NOS Spreader Links = 1 NOS Rotary Handle = 1 NOS Energy Meter = 1 NOS 400/5Amp. 15 VA CL-1 Current Transformer = 3 NOS PROVISAN FOR MCCB 63A. FP 25KA = 1 NOS Spreader Links = 1 NOS Rotary Handle = 1 NOS Energy Meter = 1 NOS 400/5Amp. 15 VA CL-1 Current Transformer = 3 NOS (i) FOR FABRICATION WORK AND WIRING WORK ETC. (Payment for this item paid under HSR 31.63)

(ii) FOR LOAD SHARING , ELC, INTERLOCKING AND ALL OTHER PROTECTION RELAYS ETC.

(iii) controllar for load sharing

(iv) battery charger trickle boost 24 v/dc pla relay and misc. Etc.

(v) programing of conrollar for load sharing

Supplying & Fixing of following capacity Carbon Dioxide (CO2) Type Fire Extinguisher ISI Marked with following specifications fully charged having safety valve, discharge hose & horn complete in all respects as required. 4.5Kgs with 1 Mtrs hose horn ( ISI Marked IS 15683 : 2006)

Supplying & Fixing ABC Type Fire Extinguisher 4 Kgs. Capacity ISI Marked IS: -15683 : 2006 filled with MAP 90% ABC powder complete in all respect as required.

Supply and fixing ABC type Modular fire extinguishers ceiling mounted 25 kg capacity

Supplying and installing at approved location approved make fire buckets 6 Nos of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold. Cost shall be inclusive of providing MS stand duly painted over a coat of primer.

Supplying and fixing 1000mm x 2000mm wide x15mm thick rubber matting (complying with ISS) and suitable to with stand 11KV as required.

Supplying and fixing standard shock treatment chart in English & Hindi mounted on wooden frame with glass.

Supplying & fixing First Aid Box for HV complete as approved by St. John Ambulance or Indian Red Cross.

Supplying & fixing rubber glooves (11 KV rating) ISI

Design, supply, installation, testing and commissioning of 150 KW Of 3 Phase solar grid tie power plant complete withallequipment, as required upto PCU including synchronizationwith grid supply and civil foundation work formodulemountingstructure. The system includes the appropriateno.ofPVModules, mounting structure for themodules. Array Junction boxes, all cabling according to thesite andsystem requirement as follows or as perapproveddrawings.Specifications of the tenderanddirectionsofSite Incharge. The rate includes thefollowing items as per site requirementand as pe+rmanufacturer's specification complete in all respects. The design should be gotapprovedfrom the Architect & Engineer-in-Charge before execution with five years warranty against manufacturing defects. Solar PV Modules (poly-crystalline) Inverter Mounting structure (fixed type) Electrical accessories Earthing kit AC cables for power evacuation AC distribution board

SUPPLYING , INSTALLATION , TESTING & COMMISIONING OF 13 PASSENGER LIFTS OF FOLLOWING SPECIFICATION HAVING 5 STOP S AND APPROXIMATE TRAVEL DISTANCE OF 24 M HAVING FOLLOWING SPECIFICATIONS Product Description Elevator Specifications Number of Persons 15 Rated Load 1020 kg Number of stops 5 Number of Access sides 1 Floor designations B,S , 1 ,2,3 Drive System Alternating Current Voltage Frequency (ACVF) Type of controller Full Collective control - Simplex Speed of travel 1.5m/s Car Size 1575 mm (W) x 1500 mm (D) x 2239 mm (H) Door Width 900 mm Door Height 2100 mm Rated output motor 7.7 kw Car Design Car walls finish in Stainless Steel Hairline LED spot in ceiling Car doors finish in Stainless Steel Hairline Car door in Stainless steel finish Granite Flooring finish in Black Sea Deco Ceiling finish in Stainless Steel Mirror 304 Full height mirror on rear car panel Car Operating Panel Stylish, touch sensitive glass panel Door open/close and alarm buttons

HIGH SIDE EQUIPMENT : CHILLERS: Supply ,installation, Testing and commissioning of Twin Screw type Water Chilling Machine with Multi Compressors each specified capacities hereunder, suitable for operation on refrigerant 134a each comprising of the following complete as per specification and as required. The scope of work shall also include lifting, shifting and positioning of chiller at location shown on drawing. Twin Screw Water Chilling Machine each having a capacity of 500 TR (Actual Capacity)at chilled water inlet/ outlet temperature of 54 Deg. F (12.2 Deg.C) / 44 Deg. F (6.7 Deg.C) with chilled water circulation rate of 1200 GPM and condenser water inlet/ outlet temperature of 90 Deg. F (32.2 Deg. C)/ 97.5 Deg.F (36.4 Deg. C) with circulation rate 1900 GPM. Refrigerant - R - 134a Evaporator Fouling Factor: 0.0005 (British Units) Condensor Fouling Factor: 0.001 (British Units) Min. COP = 6.3 at AHRI conditions as per ECBC Min. IPLV = 0.397 at AHRI conditions Min. IKW/TR = 0.63 at site condition Min. NPLV = 0.425 at site condition Evaporator Maximum permissible pressure drop: 4m of water gauge Condensor Maximum permissible pressure drop: 6 m of water gauge Each Chilling Machine shall comprise

1 No. Twin Screw type Multi Compressor Vertical/Horizontal semi-hermatic/hermetic complete single/multi circuit with automatic capacity control, safety switches, speed increasing gears, forced feed lubrication system etc. as per specifications. 1 No. Suitable capacity squirrel cage induction motor with class 'F'/'H' Insulation suitable for operation on 415+10% volts, 50Hz, A.C. Supply, (for open type compressor motor H.P. shall be at least 10% higher than the compressor BHP requirement at full load) 1 No. star delta starter suitable for compressor motor complete with ammeter with CTs, overload protection, under voltage protection, protection against phase reversal & independent single phase prevenentions etc. complete as required. Necessary Drive arrangement 1 Set lubrication device consisting of automatic electric oil pump, oil cooler, head tank, oil strainer, automatic pressure regulating mechanism, oil heater, thermal switch etc. as per specificatons. 1 No. matching shell and tube water cooled condenser of M.S. shell and integrally fined copper tubes. Designed and Constructed as per ASME standard. 1 No. matching shell and tube flooed type chiller of M.S. shell and copper tubes. Designed and Constructed as per ASME standard. 1 Lot Refrigerant piping fittings, valves and accessories to inter connect compressor, condenser, chillers and expansion valve. 1 Set Microprocessor based control panel complete with accessories as per specifications, Controls shall be suitable for hookup to BMS, compatible with BacNet/ Modbus as per specifications. Lot Refrigerant line accessories comprising of safety valves, angle valves, liquid line indications, liquid level control etc. Lot - water flow switches at inlet and outlet of condenser and chiller, water drain and air purge valves wherever required. Lot - Suction line and chiller inuslation with minimum 25 mm thick polyvinyl nitrile rubber insulation complete as required. Lot - Frame work for mounting the above condenser, chiller compressor and motor with base plate complete with antivibration pads/ springs. Lot - Initial/first charge of refrigerant gas and compressor oil. MAKE - YORK/TRANE/CARRIER/VOLTAS

SITC of Electric hot water generator of capacity300.0 KW vertical tubler shell type fabricated from MS sheet 8mm Shell 10mm Dish ends, Top openable with sufficient number of Nut Boltsand joints shall be welded and shall be tested for working pressure of 21 kg/cm² complete with sheathed tubler electric resistance type heater elements atleast 5 steps Combination capacity control, control panel with contactor, internal,wiring, safety controls, thermostat, IN and OUT connections, drain connection at the bottom, water flow switch and interlocking with control panel, Step Controller, Pressure Gauges with Ball Valves, Pressure relief Valve, Low Level cutout and Auto vent. It shall be insulated with 75 mm thick fibre insulation and covered with 1 mm thick Aluminium cladding. The unit shall be BMS compatible with necessary ports. Note: The civil foundations reqd shall be made by the tenderer. Make:Rapidcool/KEPL/Emerald

Primary Chilled Water Pumps: Supply, installation, testing and commissioning of PN16 rated Axial Split Coupled Vertical Inline centrifugal pump sets having CI casing & bronze impeller & SS 416 shaft with suitable IE2 electric motor for circulation of chilled water for central air-conditioning system. All pumps must be installed in the air(not on foundation) without any flexible bellows. The pump motor shall be IP 55 Class F Insulation suitable for 415 ± 10% volts, 50 cycles, 3 phase power supply. The price of pump shall also include the cost of thermal insulation, cabling, coupling guard etc. and suitable for following ratings as per specifications. Pump performance characteristics shall be suitable for parallel operation as follows & efficiency above 75% . Water Flow Rate : 1200 USGPM Head : 12 M RPM : 4P Motor : 15kW Make: Xylem,Grundfoss,Armstrong

Secondary Chilled Water Pumps With Motor Mounted VFD's : Supply, Installation, Testing and Commissioning of PN16 rated Axial Spilt Coupled Vertical Inline centrifugal pump sets with suitable electric motor IE3 for circulation of chilled water for central air-conditioning system. All pumps must be installed in the air(not on foundation) without any flexible bellows. The pump motor shall be IP55, class F insulation suitable for 415 ± 10% volts, 50 cycles, 3 phase power supply. Pumps shall be provided with motor mounted IP55 integrated VFD for sensorless/wireless control. 2 Nos of Wireless sensors must be considered for each zone in case of wireless operations. Separate microprocessor based controller with IP55 Protection must be considered to maintain the redundancy in variable speed pumping system(VSPS). For 1W+1S configuration pump controller is not required in sensorless control and must be considered in wireless control.The system shall be complete in all respects including thermal insulation, cabling, coupling guard etc. and suitable for following ratings & complete as per the Tender Specification. Pump performance characteristics shall be for parallel operation as follows & efficiency above 75% :- Make: Xylem,Grundfoss,Armstrong

Water Flow Rate : 600 USGPM Head : 30 M RPM : 4P/2P Motor : 18.5kW

Water Flow Rate : 600 USGPM Head : 50 M RPM : 4P/2P Motor : 37kW

Water Flow Rate : 720 USGPM Head : 30 M RPM : 4P/2P Motor : 18.5kW

Water Flow Rate : 840 USGPM Head : 30 M RPM : 4P/2P Motor : 22kW

CONDENSER WATER PUMPS: Supply, installation, testing and commissioning of PN16 rated Axial Split Coupled Vertical Inline centrifugal pump sets having CI casing & bronze impeller & SS 416 shaft with suitable IE3 electric motor for circulation of chilled water for central air-conditioning system. All pumps must be installed in the air(not on foundation) without any flexible bellows. The pump motor shall be IP 55 Class F Insulation suitable for 415 ± 10% volts, 50 cycles, 3 phase power supply. The price of pump shall also include the cost of thermal insulation, cabling, coupling guard etc. and suitable for following ratings as per specifications. Pump performance characteristics shall be suitable for parallel operation as follows & efficiency above 75% . Water Flow Rate : 2000 USGPM Head : 30 M RPM : 4P Motor : 55kW

Double Skin Floor Mounted AHU Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit withThermal Break Profile floor mounted (Horizontal / Vertical to suit site) fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside with blower, blower section and Backward/Forward Curved blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 6 Row cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor, belt drive etc. without face and bypass dampers. The AHU panels shall be insulated with 23mm thick & 38 Kg/m³ +-2 density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specifaction. The face velocity across cooling coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows: CFM TYPE SP CC/TR Note: The civil foundations/RCC Block reqd shall be made by the tenderer Make : Edgetech/Flakwood/Systemair

8000 FM 40 mm 8 RD 20

10000 FM 40 mm 8 RD 25

16000 FM 40 mm 8 RD 40 ( Outdoor Type)

Double Skin Ceiling Suspended AHU SITC of Double skin with Thermal Break Profile Air Handling Units with double blower complete with fabricated out of extruded aluminium section with 0.6mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 6 Row cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor, belt drive etc. without face and bypass dampers. The AHU panels shall be insulated with 23mm thick & 38 Kg/m³ +-2 density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specifaction. The capacity of Air-handlers shall be as follows: Hardware for hanging of AHU with GI thread rods, check nuts/washers CFM TYPE SP CC/TR Make : Edgetech/Flakwood/Systemair

1.5 TR (600 CFM)

2.0 TR (800 CFM)

2.5 TR (1000 CFM)

3.0 TR (1200 CFM)

Supply, installation, testing and commissioning of controls for fan coil units consisting of 2-way motorized spring return valves, Snap acting type heating/cooling thermostat with fan speed switch, wiring etc.

20 mm dia valve

25 mm dia valve

Supply, Installation, Testing & Commissioning of double skin Treated Fresh Air unit constructed of 0.63mm precoated GSS on outside & 0.63mm plain GSS inside with 25mm. thick CFC free polyurethane foam of density 38-40 kg/m3 injected between panels. TFA should consist of Centrifugal backward/forward curved fan & three phase IE3 motors, vibration isolators, coil section with 8 Row deep with supports, 12Fins/Inch chilled water coil, insulated drain pan of 20 gauge stainless steel 304 jointless sheet having drain connections on both sides, aluminium damper on the outlet of TFA, weather proof light in fan section,limit switch,glass window in fan section door as per specs complete with fire retardant & water proof double flexible connection between fan outlet & duct. Filter section with Pre metalic filter MERV 8 having efficiency 90% down to 10micron @ 500FPM velocity and access doors. Filter shall be UL 900 listed class 1 or class 2. Make : Edgetech/Flakwood/Systemair

2500 CFM, 20 TR with 40mm SP

3000 CFM, 25 TR with 40mm SP

OPEN TYPE EXPANSION TANKS: Supplying, Installing & Testing of open type expansion tank, fabricated out of 6mmthick MS plate construction, duty insulated as per the specifications and shall be complete with 40 mm dia outlets for system connection, overflow and drain. 25 mm dia make up connection with float valve, drain valve, and incoming line valves, vent connections, valves and fittings as required. Expansion tank shall be complete with insulation as per specifications. 2000 mm x 2000 mm x 2000 mm (high)

CHILLER SIDE VALVES : VALVES (INSULATED) : Supplying, fixing, testing and commissioning in position the following valves, strainer etc. in chilled water line complete with flanges etc and duly insulated with expanded polystyrene TF quality density shall not be less than 20 Kg/m3 for insulation as per piping specifications . All Valves in Chilled Water piping shall be @ PN 16 Working Pressure. BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot water circulation as specified ( 200 mm dia & above BFV should be gear BOX Type) Make: Advance /SIR/Honeywell

400 mm dia

350 mm dia

300 mm dia

250 mm dia

200 mm dia

150 mm dia

125mm dia

100mm dia

80mm dia

65mm dia

50mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. Make: Advance /SIR/Honeywell

200 mm dia

150 mm dia

Suction guide cum strainer : shall be of CI body provided with stainless steel screen of 3mm perforations. Screen shall be removable and replaceable without disturbing of the main pipes All strainers shall be provided with isolating valves so that the strainer may be cleaned without draining the system. Make: Advance /SIR/Honeywell/Sant

200 mm dia

150 mm dia

125 mm dia

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. Make: Advance /SIR/Honeywell

300 mm dia

250 mm dia

200 mm dia

150 mm dia

125mm dia

100mm dia

80mm dia

65mm dia

50mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

Water Flow Switch: Provinding, fixing and commissioning of approved make flow switch complete with copper conductor control wiring at chiller unit of each machine/HWG. Make : Anergy/RC/Honeywell

Supplying, Insatllation, Testing and Commissioning of Air Vent Valves : Make : Anergy/RC/Honeywell

Automatic 10 mm dia -

Manual 15 mm dia with stop cock

Pressure Gauges & Thermometers: Providing and fixing in position dial type pressure gauges & dial type industrial thermometers with isolating ball valves in both the scales (metric & British units) complete as per specifications.

Pressure gauges with gauge cock - 100 MM Dia (0-150 PSI)

Thermometers - 100 mm (0-120˚F)

Supply and installation of 20/25mm M.S. sockets for temperature & Water Pressure Gauges etc .

SITC of Ball valves with & without strainers alongwith fittings etc of sizes: Make : RC/Anergy/Advance

25 mm dia with Strainer

25 mm dia without Strainer

32 mm dia with Strainer

32 mm dia without Strainer

40 mm dia with Strainer

40 mm dia without Strainer

Supply, Installation, Testing & Commissioning of water flexible connections at Pump/Chiller inlet & outlet of size 200 mm dia.

Supply, Installation, Testing & Commissioning of water flexible connections at Pump inlet & outlet of size 150 mm dia.

Supply, Installation, Testing & Commissioning of insulated GM gate valves for drains of following sizes:- 50 mm dia for Plant room /Riser

Chilled Water Piping Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum7mm thick MS sheet for pipes of 400 mm dia and above. Make : Jindal Hisar/Tata, Insulation Make: Beardsell ,Lloyed

400 mm dia with 75 mm thick insulation

350 mm dia with 75 mm thick insulation

300 mm dia with 75 mm thick insulation

250 mm dia with 75 mm thick insulation

200 mm dia with 75 mm thick insulation

150 mm dia with 50 mm thick insulation

125 mm dia with 50 mm thick insulation

100mm dia with 50 mm thick insulation

80 mm dia with 50 mm thick insulation

65 mm dia with 50 mm thick insulation

50 mm dia with 50 mm thick insulation

40 mm dia with 50 mm thick insulation

32 mm dia with 50 mm thick insulation

25 mm dia with 50 mm thick insulation

20 mm dia with 50 mm thick insulation

Supplying, laying, fixing & testing of UPVC x 10 kg /Sqcm drain pipe complete with all necessary fittings such as elbows, tees, reducers, supports, clamps etc. Provide 'P' type trap / U trap in each drain pipes duly insulated with 6 mm thick Nirile rubber insulation. Make :Diplast,Supereme,Polyplast

100 mm dia

75 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

All Valves in Condenser Water piping shall be @ PN 16 Working Pressure.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified Make : Advance/SIR/Honeywell

600 mm dia

500 mm dia

350 mm dia

300 mm dia

250 mm dia

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating asspecified. Make : Advance/SIR/Honeywell 300 mm dia

Suction guide Cum Stainer (CI Body & SS Screen of 3 mm perforations): Screen shall be removable and replaceable without disturbing of the main pipes All strainers shall be provided with isolating valves so that the strainer may be cleaned without draining the system. - Make : Sant/SIR/Honeywell 300 mm dia

Manual Balancing valves: shall be provided with built in pressure drop measuring facility. The water flow shall be measured by online Hydronic Balancing System 300 mm dia Make : Advance/SIR/Honeywell

Water Flow Switch: Make : Anergy/RC/Honeywell/Siemens

Providing and fixing in position 100mm dia dial type pressure gauges & dial type industrial thermometers with isolating ball valves in both the scales (metric & British units) complete as per specifications. Make : Fibig/guru

Pressure gauges with gauge cock (0-150 psi) - 100 mm dia

Thermometers (0-120°F) - 100 mm dia

Supply and installation of 20/25mm M.S. sockets for temperature & Water Pressure Gauges etc . Air Vent Valves : Make : Anergy/Honeywell/RC

Automatic 10 mm dia

Manual 15 mm dia with stop cock

Flexible Coupling : Supply, Installation, Testing & Commissioning of water flexible connections at Pump/Chiller inlet & outlet of following sizes:- 300 mm dia

Supply, Installation, Testing & Commissioning of non-insulated GM gate valves for drains of following sizes:- 50 mm dia for Plant room

Pot Strainer fabricated out of 12 mm thick MS Sheet with bronze / SS-304 basket as per specification. 500 mm dia Make : Sant/Honeywell/SIR

Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. And from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Make: Jindal Hisar/TATA

600 mm dia

500 mm dia

400 mm dia

350 mm dia

300 mm dia

250 mm dia

Supply, fabrication, installation and testing of sheet metal ducts of following thickness including necessary supports, hangers, nut & bolts, gaskets, splitter dampers, vanes, etc complete as per specifications in accordance with the approved shop drawings and confirming to SMACNA Factory fabricated

24 gauge galvanised sheet

22 gauge galvanised sheet

20 gauge galvanised sheet(Site Fabricated duct conforming to IS 655) inclusive supporting arrangement as per IS. Make : ECO Duct/Airtech/Zeco

Supply, Installation, Testing and Balancing of Aluminum extruded powder coated grills with key oprated volume control dampers as per approved shop drawings & approved samples having 20 Gauge frame & 24 Gauge louvers.

Supply, Installation, Testing and Balancing of Aluminum extruded powder coated aluminium grills without dampers having 18 Gauge GI frame & 24 Gauge GI louvers.

Supply, Installation, Testing and Balancing of Aluminum extruded powder coated grills as per approved shop drawings & approved samples having 20 Gauge frame & 24 Gauge louvers.

Supply, installation, testing and balancing of square, air diffusers. All diffusers must be multislotted complete with air pattern controller. Each diffuser shall be equipped with fixed air distribution grid and antis-mudge ring where required as per the shop drawings & specifications.

Extruded Aluminium powder coated diffusers with damper

Extruded Aluminium powder coated diffusers without damper

Supply, Installation and Testing of GI volume control dampers having 20 Gauge GI frame & 24 Gauge Louver within ducts complete with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of air distribution system.

Supply, Installation and Testing of G.I. Supply air louvers with birdscreen in Ahu rooms with GI angle iron frame of 50 x6mm & 22 gauge louvers with birdscreen & VCD on the inside as pe the design approved by the HVAC Consulgtant/Client/Architect

Supply, fabrication, installation and testing of double layer (fire proof) flexible connection constructed of fire resistant material as per drawings/specifications.

Supply, installation, testing and commissioning of fire dampers of at least 120 minutes at 250oC fire rating as per specification & approved shop drawings, complete with actuator with spring return mechanism and control panel, limit switch to on fans when the damper opens.

Fire Dampers

Actuators with spring return mechanism

Supply, installation, testing & commissioning of manual fire damper (spring return type) of approved make of atleast 90 minute fire rating and as per the specification & detail given earlier in the relevant section. The fire dampers location refer drawing, at all fire rated crossovers((shafts/walls etc.). Fire Dampers

Supply, installation & testing of transfer air grilles of extruded aluminium.

SITC of Acoustic lining of the supply duct with 10 mm thick Accosound Nitrile board with suitable adhesive to be pasted inside of the Plenum duct complete in all respects Acoustic lining Make : K Flex/Aramacell/Paramount

THERMAL INSULATION :(Ducting) Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. Make : K Flex/Aramacell/Paramount

13 mm thick

19mm thick

Supply and Installation of under deck insulation of exposed roof with 50 mm thick TF quality expanded polysterene 24kg/CuM secured with CPRX compound and further with dash fasteners at regular interval as per direction of and satisfaction of Engineer In-Charge. Make : Beardsell ,lloyed

FANS FOR SMOKE EXHAUST AIR -NORMAL+ FIRE MODE Supply, installation, testing & commissioning of Tube Axial Flow Fan of adjustable pitch , the blade of the fan shall be made out of Die cast alluminium alloy duly dynamically and statically balanced mounted directly on TEFC Sq. Cage Induction Motor suitable for 3 phase 415 V ±10% 50 C/S AC supply with cylindrical casing & motor support. All Exhaust Fans Motor and Cabinet shall be suitable For smoke exhaust application & thermally rated For 250 Deg.C For 2 hours as per EN-12101-3 2002. Fresh Air Fans are with Class F motor. Fan with Long casing and HOT DIPPED GALVANISED. Impeller Die cast Aluminium. Fan capacities based on following details complete as per specification.

Fans to have NON RETURN DAMPER AND GI safety wire mesh screen on exposed face. Cost to be included in item rate. Basement -1, Car Parking Area Air Qty. = 41400 CFM Static Pressure = 25 mm Wg Fan Speed = Not exceeding 1450 rpm Outlet Velocity = Not exceeding 14 m/s Tube Axial Fans as described above. Make :System Air/LTI/Flaktswood

FRESH AIR AXIAL FAN Basement -1, Car Parking Area Air Qty. = 43470 CFM Static Pressure = 25 mm Wg Fan Speed = Not exceeding 1450 rpm Outlet Velocity = Not exceeding 14 m/s Tube Axial Fans as described above. Make :System Air/LTI/Flaktswood

Basement -Stilt ,Car Parking Area Air Qty. = 33300 CFM Static Pressure = 25 mm Wg Fan Speed = Not exceeding 1450 rpm Outlet Velocity = Not exceeding 14 m/s Tube Axial Fans as described above. Make :System Air/LTI/Flaktswood

Supply, installing, testing and commissioning of Ductless Ventilation / Jet fans as per specifications for Normal ventilation and Smoke Extraction application. The complete fan assembly with its Casing, impeller & motor (not only the motor) shall be imported from manufacturer and certified as tested for 250 Deg C for 2 hours operation. The casing shall be made of hot dipped galvanized steel with steel flanges at both ends.Length of silencer should be 2D+2D mm. Impeller Die cast Aluminium .The Motor shall be dual speed and run on the electrical power suitable for 415V/3 Ph/50Hz. Make :System Air/LTI/Flaktswood

Basement -1,Car Parking Area - Capacity- 1588 / 3175 CFM, 315 mm Dia

Basement -Stilt Car Parking Area - Capacity- 1588 / 3175 CFM, 315 mm Dia

Preparation and approval of CFD ( Computational Fluid Dynamics ) Analysis in Basement Areas ( both levels) .CFD analysis to decide the correct location and quantity of jet fans. CFD analysis will be carried out for both normal and fire mode ventilation situation considering 6/12 ACPH, airflow strategy and control strategy to confirm the operation logic. CFD analysis will model all the cars, car parking bays, beams, structures, columns, voids, shafts, ramps, proposed fresh air route, fresh air shaft, exhaust air shaft and preliminary location of jet fans shown in the drawing. CFD output will give complete simulation of ventilation scheme not limited to velocity profile, temperature profile, smoke temp and movement profile, CO level profile, air movement profile. The number of repeat simulations shall be carried out until satisfactory results are achieved.

Supply, installing, testing and commissioning of Analog type Carbon Monoxide based Gas detection system comprising of CO sensors, with DDC controller, built in power supply units. Detectors shall be mounted in enclosure with sensor lid projection at distance not more than 1500 mm from floor and shall have suitable arrangement to fix on wall or on ceiling as directed including SS 304 grill of size (200 x 150 x 125 mm) for protection. Sensor shall have range of 0-250 ppm non linear sensing, sensors shall be solid state type with operating temperature range of -10 to 50 deg C and relative humidity of 10% to 100% [non condensing]. Enclosure shall be in minimum IP 55 construction. Seperate MS Powder Coated Junction Box shall be provided near each sensor for termination of armoured copper cable and final terminal inside sensor with flexible copper cable and IP 65 PVC glands .

VENTILATION LOGIC CONTROL PANEL ( Common for Bas-1 & Bas-2) LOGIC CONTROL PLC PANEL to perform the logical operation of speed change in fans from Low to high speed based on the CO Level in the Basement. The control is envisaged for JET Vent fans and Axial Fans. all these fans should also be SWITCHED on in full speed incase of receipt of FIRE Signal. The PLC will be with Logical Operation of pollution mode and FIRE mode is desired from PLC. Vendor should submit SLD and GA drawings for employers approval. PLC control panel will be consisting of IP 55 enclosure, IO blocks for analogue and digital input output modules, status indicator fault alarm and status, preloaded licensed life time HVAC software to suit the control logic, Open protocol communication module inserted in dedicated slot for MODBUS/BACnet, Built in communication link on integrated RJ 45 port, display block for controller status, connectors, terminal blocks, relays, relay output blocks mounted on DIN rail. Panel shall be supplied with suitable arrangement for wall mounting application.(Refer Technical Specifications).

PANEL 1&2- FOR BASEMENT1 - 17 JET FANS+ 3 EXH FANS

PANEL 3&4- FOR STILT BASEMENT1 - 15 JET FANS+ 3 EXH FANS

SITC of Powder Coated Extruded Aluminum Linear Fresh Air Grills of 15° Airflow Angle with Volume Control Damper in Aluminum Construction

Supply, Laying, testing and commissioning of FRLS XLPE armoured cables for Electrical Power and controls from MCC/LSCP/PDB to respective Equipments with earthing, clamped on surface or on cable trays, structural supports and cable supports provided. The scope includes End Termination of cables with Double Compression type Brass Cable Glands and Copper Lugs, clamping of cables by ready made G.I. spacers, saddles or clamps fabricated out of GI. strip 3 mm thick, treasing and Clamping of Cable on cable tray or surface, supply of all clamping materials and hardware etc., providing cable tags made out of aluminium/PVC laminated strip and 75x20 mm in size with cable number and size punched on it. Cable tags shall be tied to cables at every 20 meter interval and at both the ends. MS Powder Coated Junction Boxes with Bolted type terminals of suitabel size shall be provided near all Fan Motors for termination of armoured cables. Make: Havells/Ecko/Finolex//L&T/KEI)

4C x 6 Sqmm Copper Cable ( For Fire Exhaust Fans)

4C x 1.5 Sqmm Copper Cable ( For Jet Fans )

Supply & laying of XLPE armoured copper conductor twisted shielded control cables 3C X 1.5 Sq.mm twisted shielded cables for CO sensors. Make: Havells/Ecko/Finolex//L&T/KEI)

Earthing for all equipments - 8 SWG bare GI. Wire

Supply and Erecting PERFORATED type Hot dip G.I. cable tray of 14G of specific dimensions. The cable tray shall be hung from ceiling / fixed to wall with necessary ceiling suspensors, tee, flat sections, nuts etc., together with tees, bends etc. including cost for supports as described. The tray shall be earthed. Min size (not a limitation) of supports shall be as follows (a).-up to 300mm tray 2nos. 8mm full threaded GI. rod with 2nos.anchor fastener and "C" channel support at 500mm distance (b) 450 to 600mm tray 2nos.10mm full treaded G.I. rod with 2nos. anchor fastener and "C" channel support at 500mm distance (c) 750 / 1000 mm cable tray with fabrication of 25 x 6 or 50 x 3 mm angle frame with min. 4 nos anchor fastener at 500 mm distance.

50mmx300mm x 50 mm.

50mmx100mm x 50 mm.

(HVAC DISTRIBUTION PANEL) Fabricating, supplying,installation, testing and commissioning of electrical control panel of cubical construction,floor mounted type , fabricated from 2 mm thick CRCA sheet compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatrment process,cable alley,inter connection, having switchgears and accessories mounting and internal wiring, earth terminals numbering etc complete in all respect ,suitable for operation on 415 V ,3 phase,50 Hz AC supply with enclosure protection class IP 42 as reqd INCOMINGS : 2500 Amps. each four pole with 100% neutral horizontal drawout type air circuit breaker of fault breaking capacity 50 KA (Ics = Icu = Icw for 1 sec. at 415 V ), impulse voltage (Ui) 1000 V, EDO operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF, 6 NO + 6 NC auxiliary contacts, service/test/ isolated position indicators and frame earthing contact, confirming to IS : 13947-2, 1993 as amended up to date complete with following accessories for each ACB - 2 Nos. Independent Electrical spring closing mechanism - 1/2 No. Microprocessor release (EMI & EMC Certified) for over current, earth fault & short circuit protection - 1 Set. Intelligent multifunction digital meter to read V, A, KVA, KWH,THD, PF Hz etc. having RS 485 port and compatible to PC with modbus protocol with 3 Nos. resin cast CTs of 2200/5 A class 1.0 accuracy and 15 VA burden. - 1 Nos. Phase indication LED lamps with 2 Amps.back up MCB, breaker ON/OFF indicating light with MCB, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required - 1 set. Shunt trip coil 220 V A.C. Bus Bar 6000 A 415V 3 phase 4 strip Aluminium Busbar Outgoing 800A TP MCCB with 100 kA breaking capacity- 6 Nos. 125 A TP MCCB with 25 kA breaking capacity – 10 Nos. 100 A TP MCCB with 25 kA breaking capacity – 8 Nos. 63 A TP MCCB with 25 kA breaking capacity – 6 Nos. Space for accommodating starter for Cooling Tower Fan Motors in the compartment of 125 amp. TP MCCB - 4 Nos. Intelligent multifunction digital meter to read V, A, KVA, KWH,THD, PF Hz etc. having RS 485 port and compatible to PC with modbus protocol with 3 Nos. resin cast CTs of suitable rating class 1.0 accuracy and 15 VA burden with all incoming/ outgoing ACB/ MCCB Panel Make : ABB/Siemens/L&TUnitech Power System/Vrindavan Electricals/KEPL

AHU Panel SITC of AHU panels duly powder coated wall mounted Made out of TATA/SAIL/ESSAR/JINDAL/Reputed make CRCA Sheet of 1.6 mm thick consisting of Upto incomer as MPCB suitable as per AHU ON/OFF/TRIP indication light LED type, DIGITAL Ammeter with ASS; CT's 30/5; contactors up to32A or Suitable (with 2 NO+ 2NC); Start/Stop push buttons with auto & Manual control switch, Single Phase Preventer, MCB DP upto 10 Amps C Curve ,Over load Relay 16-25A or Equivalent Suitable , power & control terminals; neutral link and internal wiring & connections for AHU motors upto 5 HP or Suitable Panel Make : ABB/Siemens/L&TUnitech Power System/Vrindavan Electricals/KEPL

SITC of PVC Armoured XLPE Insulated cabling Aluminium/copper for power & controls complete with Saddles, lugs, thimbles duly crimped etc of following sizes:

400 MM² x 3½ core- Aluminium Armoured

300 MM² x 3½ core- Aluminium Armoured

240 MM² x 3½ core- Aluminium Armoured

185 MM² x 3½ core- Aluminium Armoured

120 MM² x 3½ core- Aluminium Armoured

35 MM² x 3½ core- Aluminium Armoured

25 MM² x 3½ core- Aluminium Armoured

10MM² x 4 core- Copper Armoured

6.0MM² x 4 core- Copper Armoured

4.0MM² x 4 core- Copper Armoured

2.5MM² x 4 core- Copper Armoured

1.5 MM² X 4 C CU -- for Controls (Multistranded flexible) with, saddles etc.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 62.5 mm depth X 2.0 mm thickness

375 mm width X 62.5 mm depth X 2.0 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying, Installation, Testing & Commissioning of Non- PCB based Information Outlet (I/O) RJ45, Tolless Termination TIA-568C Category-6, Termination of Catergory-6 UTP Cable, UL listed ,Shall conform to Category-6 as per the EIA/TIA-568C.2,Shall support network line speeds up to 1 Gbps, Shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable, Shall have minimum duraility of 950 or Above mating cycles and 200 termination cycles. Certified by independent labs like ETL/GHMT/3P for compliance to EIA/TIA-568C.2 complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of Single Faceplate Shall be Duplex Port (RJ45) square plate, dimension as per commercially available modular office furniture.Shall have spring shuttered front access for preventing ingress of dust,Shall be supplied with Gang Box of the same size by System Integrator complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of UTP Jack Panel, loaded with 24 nos UTP ports for Non-PCB based IO Jacks (RJ45, TIA-568C Category-6, Shall have integrated bonding bar or other mechanism for grounding, Shall be loaded with individually replaceable 24 nos. Category-6 certification by Jacks complying with TIA-568.C.2 , Shall be having a 6 port module construction for better cable dressing at the rear, the jacks shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of 4-pair Unshielded twisted pair with a cross filler (+), meeting Category 6 standards as per TIA-568C.2, The cable should be tested till 250 MHz , Shall be Fire-Retardant, Low-Smoke & Zero-Halogen as per IEC 60332-1, IEC 61034-2 & IEC 60754-1 respectively. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of Category 6, UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. UTP Cable will be 1.0 mtr. complete in all respect. Jacket - LSZH Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of Category 6 UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. Blue UTP Cable, 2 Meter complete in all respect. Jacket -LSZH Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of 20 Pair anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables with suitable clamps, saddles and including making terminal joints complete as required.Make-Finolex/Delton/Vimco

Supplying, Installation, Testing & Commissioning of 50 Port telephone Jack Panel Approved.Make-Siemon/Panduit/Legrand

Supplying, Installation, Testing & Commissioning of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount ,Shall have all accessories including coupler plates pre loaded with 12 Nos of LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie to ITU-G657.B-Bend insestive fiber. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of Fiber Optic Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-11801-OM3 50μ Duplex, LSZH,All patch cords shall conform to EIA/TIA-568C.3 and ISO/IEC-11801,Shall be Duplex Multi Mode Fiber Optic Patch Cords OM3 50μ,Shall support network line speeds up to 10 Gbps.Shall have LC-LC Connector connectors at the ends complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of OM3 50/125μ Type Pigtails of ISO/IEC-11801-OM3 Pigtails with LC Type Connectors,pigtails for terminating fibers on the FOPP complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying, Installation, Testing & Commissioning of 50μ, 6-core Multi mode OM3 metallic armored Fiber cable as per ISO/IEC-11801, Shall be able to meet Gigabit & 10 Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10G Base-X) Tensile load should be 4000 Newton or higher and crush resistance should be 4000 Newton or higher ,The attenuation @ 850 nm should be ≤ 2.7 (Max) db/Km and @ 1300 nm should be ≤ 0.7 (Max) dB/Km, the fiber construction can be unitube or multitube, but tensile and crush resistance parameters should be matched, the jacket shall be FRLSZH complete in all respect. Make-Siemon/Heinrich/Legrand

Supplying Installation testing and Commissioning of 24 port 10/100/1000BASE-T ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP ,stackable upto 10 switches, should support external redundant power supply, certified , each switch should be provided with stacking port/cable complete in all respect . MakeRuckus/Cisco/Extreme.

Supplying Installation testing and Commissioning of Small Form Factor Pluggable 1 Gigabit Ethernet (SFP+) SR Optics. MakeRuckus/Cisco/Extreme.

Supplying Installation testing and Commissioning of 32 Port Fiber Switch 10/100/1000BASE-T ports, with up to 4X 10GbE uplinks and 2X 40GbE uplinks, Switch should support stacking bandwidth of minimum 160gbps, Modular operating system, 32 1 Gig SFP port with additional 4 no. of 10g SFP+PORT, redundant power supply, layer3 switch, each switch should be provided with stacking port/cable complete in all respect. MakeRuckus/Cisco/Extreme.

Supplying Installation testing and Commissioning of 350W AC Power Supply, Front-to-Back AirflowMakeRuckus/Cisco/Extreme.

Supplying Installation testing and Commissioning of SFP 1000Base-T 10/100/1000 Copper Transceiver Module for up to 100m transmission on Cat6 complete in all respect. MakeRuckus/Cisco/Extreme.

Supplying, Installation, Testing & Commissioning of Floor Standing Network/Server Rack - 42U / 800w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w Rear MS Door Split Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Vertical Cable manager 80mmW 42U Shelf, Stationery 700mm N/W PDU 12Sockets 5/15Amps with MCB Mounting Hardware (Pkt. Of 20) earthing Kit 150mmH Cable manager 1U MS with Loops complete in all respect. Make-APC/Heinrich/VALRACK

Supplying, Installation, Testing & Commissioning of Floor Standing Network Rack - 22U / 600w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 22U/800d Front MS Door perforated honeycomb 22U/600w Rear MS Door (Fully Perforated - Mesh) 22U/600w Fan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Cable manager 1U MS with Loops Shelf, Stationery 475mm N/W PDU 7Sockets 5Amps with MCB Mounting Hardware (Pkt. Of 20) Vertical Cable Channel 50mmW 22U complete in all respect.Make-APC/Heinrich/Valrack

Supply Installation, Testing and Commissioning of Server Based EPABX Fully Computerized IP System, SIP Compliant. Multi slot 19: U Rack Mountable 2U Rack Expandable upto 200 Ports Presently Configuration as Below . Make-NEC/Avaya/Cisco CO Line 16Nos. PRI(30 Channel) 1Nos. SIP Extension 32Nos Digital Extension Circuits 32Nos Analog Extension Circuits 96 Nos.

Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level IVR software with 6 different languages and 4 time schedule(As per OEM).

Supply Installation Testing and Commissioning of Digital Phone (24Key+ 60-line DSS Console) Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ), Security lock key XML open interface .Make-NEC/Avaya/Cisco

Supply Installation Testing and Commissioning of 24Key Digital Phone Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface .Make-NEC/Avaya/Cisco

Supply Installation Testing and Commissioning of Digital Phone 6 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator . Make-NEC/Avaya/Cisco

Supply Installation, Testing and Commissioning of Analog CLI Phone with handsfree. Make-Binatone/Beetel/Panasonic

Supply, installation, testing and commissioning of of IP Dome style 1/2.8 '' 2.4 MP CMOS Sensor Progessive with effective 1920 (H) x 1080(V) pixels ,Video Compresion H.264/H.265/M-JPEG, (Color)/F1.2, 0 Lux (IR On), motorized varifocal lense 2.8 to 12 mm , Smart IR Distance upto 30/40 mtr, WDR ,Auto Iris ,Dual Streaming ,Fram rate 25 FPS on 1080 MP resolution , Electronic Shutter Speed Auto/Manual, 1/3(4)~1/100000s, 3D DNR , Motion detection , Ethernet port 10/100 Mbps, ,ONVIF support ,Power input 12 V DC and Power over Ethernet ( No need of additional power cable ) & 3D adjustment ,Wall mount . Heavy duty metal body, IP65 & IK 10 with dust proff cable connectors cap as per specification . Make-Heinrich/Mobotix/Axis/Bosch

Supply, installation, testing and commissioning of IP outdoor bullet style 1/2.9 '' 2.4 MP CMOS Sensor Progessive with effective 1920 (H) x 1080(V) pixels ,Video Compresion H.264/H.265/M-JPEG, (Color)/F1.2, 0 Lux (IR On), motorized varifocal lense 2.8 to 12 MM , Smart IR Distance upto 50 mtr, WDR minimum 60 DB ,Auto Iris ,Dual Streaming ,Fram rate 25 FPS on 1080 MP resolution , Electronic Shutter Speed Auto/Manual, 1/3(4)~1/100000s, 3D DNR , Motion detection , Ethernet port 10/100 Mbps, ,ONVIF support ,Power input 12 V DC and Power over Ethernet ( No need of additional power cable ) & 3D adjustment ,Wall mount . Heavy duty metal body, IP66 with dust proff cable connectors cap as per specification .Make-Heinrich/Mobotix/Axis/Bosch

Supply, Installation, Testing & Commissioning of Rack mount single chassis standalone Network Video Recorder with DVI-I, HDMI, 2 display ports, simultaneous monitors. It should connect min 128 full HD (1920x1080p) cameras per appliances. It should support H.264,H.265 & H.265+ ,Support up to 4k,5 MP cameras ,Support Recording resolution 4K, 5 MP/4 MP/3MP/1080p/UXGA/720p/VGA . It must continuously record up to 450 Mbps of video for high concentration of high definition IP cameras.Local client display support .It should support streaming live/recorded video simultaneous PC clients.NVR should audio input/output feature.6 USB slot .It must support Operating temperature should be 5 – 35° C. NVR should support maximum 120 TB (It should be configured as per the storage calculation provided by VMS OEM. NVR shall have 2 Gigabit 1000Base-T RJ-45 NIC card. NVR shall have RS-485serial port capabilities to communicate with serial devices. It should support It should support 3/1Alarm Inputs/Output. Operating Temperature 40° - 95°F (4.5° - 45°C). Operating System must be support Windows/Linux both platform & Should Support up to 128 Cameras. Make-Heinrich/Mobotix/Bosch/Axis

Supply, installation, testing and commissioning of Enterprise Class 6TB HDD. Make-WD/Seagate

Supply, installation, testing and commissioning of Video/client Management System (VMS) software shall be used to view live and recorded video from capture cards and IP devices/NVR connected to local and wide area networks. The software shall have a client/server-based architecture that can be configured as a NVR base system with the client software running on the server/client hardware and/or the client running on any network-connected TCP/IP workstation. Multiple client workstations shall be capable of simultaneously viewing live and/or recorded video from one or more NVR. Multiple servers shall also be able to simultaneously provide live and/or recorded video to one or more workstations. The software shall also have the ability to be installed on an IP edge device—such as an IP camera or encoder that allows for 3rd party applications—allowing the device to serve as both a server and IP video recording device.Make-Heinrich/Mobotix/Axis/Bosch

Supply, installation, testing & commissioning of 12 Port PoE+ Switch with 2 SFP slots , 12 x 10/100/1000 Base-T PoE+ ports, support STP, RSTP, MSTP, IGMP v1/v2/v3 snooping, STP root guard, Voice VLAN, MLD snooping (MLDv1 and v2). Switch OEM should have 8 spare depots in India. Switch OEM should be in Gartner Leader quadrant of Datacentre Networking quadrant.Make-Ruckus/Cisco/Extreme

Supply, installation, testing & commissioning of Client Workstation having Intel Core i5 orginal motherboard, 16 GB RAM, Video graphics card 2 GB Licensed Windows 8 Professional (64 bit) and 1 TB Hard Disk with Web camera,Printer and finger print scanner.Make-HP/DELL/IBM

Supplying, Installation,Testing & Commissioning of 55 " LED Full HD TV Resolution 1920 x 1080 ,Contrast Ratio (Typical) 5000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock, HDCP Support, Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-Swith Mounting Brackets as per Technical Specification complete in all respect.Make-Sony/Samsung/Panasonic

SITC of 6W Recessed Ceiling speakers with following features:-Speaker Drive 6", Complete Aluminium grille and Metal baffle, line matching transformer 100/70V line. Variable wattage tappings of 6 / 3 / 1.5, Effective frequency range 110-15kHz (BS6840), SPL@1m/1W=91dB, 180 deg dispertion, snap on spring mounting, Peak SPL 97dB complete with necessary mounting hardware & accesories. Make Heinrich/Bose/ASL/Martin Audio

SITC of 20 W 4" two way wall mounted speaker with following features:- Built-in 100 / 70 V Variable wattage tappings of 20 / 10 / 5 Watt, SPL 1W/1m = 86dB, SPL@Full power = 99 dB, EASE/CATT/ULYSSYS DLL read, Frequency Response 130 Hz - 15 kHz, Speaker Drive - 4" + 1.5 ". Complete with all Mounting Accessories.Make Heinrich/Bose/ASL/Martin Audio

SITC of 8 zone digital voice evacuation system Controller having inbuilt 500 watt Amplifier, and compliant with the standards of BS EN54-32 & EN60849. The System should be capable to EVAC, paging, PA and BGM and it shall have SD card memory for the recording of EVAC and Alert message. The System should Support Class AB Speaker line with Speaker line supervision. 100V Line speaker output with seperate zone volume control. Seperate indicators for status, Priority level, two input for mic, 4 Line input and one rec output, the system shall have fireman microphone and zone capacity up to 128 Zones. Make Heinrich/Bose/ASL/Martin Audio

SITC of Remote Paging microphone with minimum 12 buttons and Busy/Hole Indication. The Microphone Should be suitable for Desktop mounting.Make Heinrich/Bose/ASL/Martin Audio

Supply Installation Testing & Commissioning of 500W RMS Single Channel Class-D Digital Power Amplifier with Switch power technology for power electricity saving. Amplifier shall have Following Features: 500W RMS per Channel, Amplifier Output 100V, Short Circuit, Power, Tempreature, Overload Protection, Auto Cooling Fans. THD <0.1%, Frequency Response 20Hz - 20kHz, AC & DC Fuse, SNR >80dB. Make Heinrich/Bose/ASL/Martin Audio

Supply, Installation, testing and commissioning of Media Player, DAB/FM RDS Tuner, CD/MP3 from Disc, SD-card or USB complete required as per specifications. Make: APART-AUDIO MARTIN AUDIO / Heinrich

Supply Installation testing and comisioning of 19-inch Equipment Rack with standardized frame or enclosure for mounting multiple PA controllers, CD player, Amplifiers etc modules. Size 24U.Make-Heinrich/Rittal/VALRACK.

Supply & Laying of 1.5 sq.mm. multistrand PVC sheathed Two Core Twin Twisted Speaker Cable in Exiting PVC Conduit. Make: Finolex/Vimco/Polycab

Supply, Installation, connecting testing and commissioing of networkable 12 Loops Micro processor based 2 wire fault tolerant loop with optional redunadant network module ,each loop shall have the cpability of connecting 126 devices and integrated operating unit for up to 1512 addresses device,The fire alarm control panel shall have built in degarde mode function.The panel should have inbuilt TCP/IP communication for Panel Program and Remote Monitoring option through LAN or WAN communication.The panel shall be able to give location of all fire and More Fire /fault and Isolation conditions of addressable units via the address codes.The panel shall have the capacity of storing upto 2000 events.Further, the panel must be able to automatically switch ON /OFF respective control module when ever any alarm is triggered. The panel should have inbuilt common Alarm, Fault and monitored sounder output. The panel shall have a 8x40 characters LCD display with resolution of 256 X 112 pixels, and analog output, external/inbuilt printer to log all fire or fault events complete in all respects.The Panel Should have protection caregory of IP30. Also the panel should have the option to operate in manned and unmanned mode.The panel shall have a built in power supply and battery charger along with maintenance free 24 AH,2X 12 volt SMF Lead acid batteries capable of running for a minimum of 24 hours with battery charger complete as required. Duly Approved by EN54,LPCB,VDS and FM.Make-Siemens/Heinrich/Bosch

Supply, Installation, Testing & Commissioning of EN-54 Compliant, Vds & FM approved, Active Repeater Panel / Remote Terminal with mounting bracket and required installation accessories. The remote terminal shall facilitate monitoring & control of fire events from pre- decided strategic location away from the main FACP. The remote terminal shall facilitate monitoring and control of fire events for each and every device connected to the FACP. It shall have 6 lines x 40 characters display.Make-Siemens/Heinrich/Bosch

Supply, Installation, Testing & Commissioning of EN-54 Compliant, Vds & FM approved, Intelligent Analog Addressable Multi-Sensor type Smoke Detector with inbuilt turbo Isolator and integral response indicator with 360 degree viewing angle. Detector shall communicate 3 danger levels for differentiated alarm activation and high tolerance to dust,dirt, temperature fluctuations and air currents. Detector should have unique address for communication and assigned through panel with Mounting Base as required with the protection category of IP40. Make-Siemens/Heinrich/Bosch

Supply, Installation, Testing & Commissioning of EN-54 Compliant, Vds & FM approved, Intelligent Analog Addressable Smoke detector with standard mounting base, LED, Adddress Switch, complete with MS Powder coated Junction Box for mouting on Surface / on False Ceiling etc.It should also be capable of full digital communications with the fire alarm panel, complete as required. Make-Siemens/Heinrich/Bosch

Supply installation, Testing & Commissoing of responce Indicator Alarm status is indicated By Red colour LED, Operates on 12 VDC, Dual LED’s for 360 visibility, Flush / Ceiling wall mount,Operating Voltage : 12 VD.C, Operating Current : 10mA, Approved. Make-Agni

Supply, Installation, Testing and Commissioning of EN-54 Compliant, Vds & FM approved, Intelligent Addressable Manual call point with inbuilt turbo Isolator suitable for flush or surface mounting, call point shall include test key feature without removing the glass. Also should have protection category of IP44 and extra acceesories as required. Make-Siemens/Heinrich/Bosch

Supply, Installation, Testing & Commissioning of EN-54 Compliant, Vds & FM approved, addressable Control Module with inbuilt Turbo Isolator. The module shall have LED indication for Normal, Fault, Test & Alarm activation. The Module shall be quoted with required junction box and mounting accessories. The module shall have IP40 protection. Make-Siemens/Heinrich/Bosch

Supply, installation, testing and commissioning of EN-54 Compliant, Vds & FM approved, Automatic Analog addressable Duct Detector with Duct Housing and Duct probe tubes complete with Photoelectric Smoke Detector with mounting Base, alarm LED shall be viewable from 360 degrees. The Detector shall have automatic Electronic/ dip switch addressing feature & each of these shall be equipped with fault Isolator/ External Fault Isolator complete with the GI Mounting Box and the hardware etc. as required.Make-Siemens/Heinrich/Bosch

Supply, and fixing of following sizes 500V grade Mineral Insulated Copper conductor Fire Survival with outer sheathed Copper cable approved by LPCB and as per IEC60331, BS 5839-1, BS 6387 and BS 7346 standard along with accessories/ termination/glands asper BS EN 60702 Part 2 and all necessary material to complete the Termination. The cable can sustain 950degree temp for three hours. 2x1.5 Sqr mm. Make: Finolex/vimco/polycab

Supply, installation, testing & commissioning of Dual band 802.11ac Indoor Access Point, BeamFlex, 2x2:2, 1-Port, PoE, Does not include power adapter or PoE Injector. Limited Lifetime Warranty and Secure Mounting Bracket for Mounts to hard wall/ceiling, pole, and truss without pad-lock support. complet in all respect.Make-Aruba/Ruckus/Juniper

Supply, installation, testing & commissioning of Wi-Fi Controller with 4 Gig Ports, with 75 APs license, Power Supply and HA mode alongwith 3 year support.Make-Aruba/Ruckus/Juniper

Supply (installation, testing and commissioning) of pump electrically driven fire-pump & Sprinkler pump & Fire Hydrant system suitable for automatic operation consisting of the following : Horizontally mounted end suction centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply, complete with flexible coupling and coupling guard as required. Fire pump having C.I. body, bronze impeller and S.S. Shaft with , capable for delivering 2850 Lpm water at 70 mts.head to ensure a minimum pressure of 3.5kg/cm2 at the farthest hydrant. Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase 50 HZ A.C supply, for the above pump with synchronous speed of 2900 RPM. 55KW/75 HP. Common base plate for (a) and (b) from M.S. Channel for required size.

Supply, installation, testing and commissioning of pump Diesel Engine driven fire pump suitable for automatic operation comprising of the following : Horizontally mounted end suction centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply, complete with flexible coupling and coupling guard as required. Fire pump having C.I. body, bronze impeller and S.S. Shaft , capable for delivering 2850 LPM of water at 70 mts.head to ensure a minimum pressure of 3.5kg/cm2 at the farthest hydrant. The pump should meet the condition of Local fire Authority). Water Cooled Diesel engine of speed 1800 RPM for the above pump with automatic starting mechanism and other accessories including fuel tank (fabricated from MS sheet painting with two coats of synthetic enamel paint over a coat of primer) capacity 200 Its (fitted with Magnetic oil level indicator, MH with cover drain valve, Air vent hydraulic pumps including structural supports (painted with approved shade), 2 Nos. x 12 volt battery, heat exchanger with necessary piping connections & fittings flexible coupling, coupling guard & exhaust pipe with asbestos rope as per drawing complete as required. Common base plate for (a) and (b) from M.S. channel of required size. Suitable cement concrete foundation with plaster, Antivibration arrangement of cushy foot mountings. 24 volts, 180 AH Lead battery - Exide make ( 12 volts-2 Nos) with boost / trickle charger for starting the engine automatically as required.

Supply, installation, testing and commissioning of . jockey pump comprising of the following : Horizontally mounted end suction centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply, complete with flexible coupling and coupling guard as required. Fire pump having C.I. body, bronze impeller and S.S. Shaft, capable for delivering 180 LPM of water at 70mts.head to ensure a minimum pressure of 3.5kg/cm2 at the farthest hydrant. The pump should meet the condition of Local fire Authority). Squirrel cage induction motor TEFC type for operation on 415 V, 3 phase 50 HZ AC supply for the above pump with a synchronous speed of 2900 R.P.M. with flexible coupling and coupling guard etc. as required. 11KW /15 HP, Common base plate for (a) and (b) from M.S. channel as required size Suitable cement concrete foundation with plaster, Antivibration arrangement of cushy foot mounting

Supply, installation, testing and commissioning of 1HP Sump Pump with fitting as required Complete.

SITC OF TERRACE PUMP Supply, installation, testing and commissioning of ELECTRIC MOTOR DRIVEN, horizontal End Suction type, centrifugal fire duty operation pump, (with mechanical seal, bronze impeller and carbon steel EN-8 shaft) capable for a DISCHARGE of 900 L.P.M. at a HEAD of 35 MTRS., coupled through flexible coupling (i/c coupling guard) with totally enclosed, fan cooled squirrel cage 4 pole induction motor suitable for operation on three phase AC supply of 415 + 10% Volts, 50 Hz, fixing the coupled pump and motor on a common structural base frame, making a suitable cement concrete foundation and mounting the complete pump-motor set on the foundation using suitable numbers of anti vibration mountings as per the design / recommendations of the manufacturer and as per the detailed specifications given below: Pump type : - Kirloskar make End Suction ModelDB 50/16 (CI+MS in Br-Impeller, M/Seal (fitted). Motor:- Kriloskar make Electric Motor 12.5HP/9.3KW 2900RPM 3PH on MS fabricated base frame , coupling & guard.

Providing, fixing, testing and commissioning of pressure vessel (250 mm dia & 1500 mm height) for pressurization of fire system complete with pressure switches with isolation valves, pressure gauge with isolation valve, valves at outlet / drain to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top Duly painted from inside and outside complete as required.

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 16 Kg / cm2.

Supplying, Installation, Testing and Commissioning of pressure switches suitable for operating with fire hydrant systems for working pressure of 8.8 Kg/cm² including electrical control wiring with suitable copper conductor PVC insulated and sheathed control cable upto control panel, connections etc. complete as required.

Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with nitrile Bronze / G.M. seat duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 item code K- 706 as required.

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

Supplying, Installation, testing and commissioning of Double flanged SLUICE VALVE (all valves shall be ISI marked and shall be one approved makes) of PN. 1.6 with Non rising spindle, bronze/ gun metal / SS seat complete with nuts, bolts, washers, gaskets confirming to IS 14846, item code K-504 of following sizes as required .

200mm dia

150mm dia

Providing, Installation, Testing and Commissioning of double flanged cast iron Non-Return Valve, PN 1.6 of following sizes confirming to IS : 5312, item code K-516 complete with rubber gasket, Gl bolts, nuts, washers etc. as required.

200mm dia

150mm dia

100mm dia

Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. Item code K-527 complete as required.

200 mm dia.

150 mm dia.

Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications. 150 mm dia.

Supplying, Installation, Testing and Commissioning of CI body flanged type Foot Valve with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. Item code K-518 complete as required 100 mm dia.

Supplying, laying, fixing, testing and commissioning of following sizes (NB) of ISI marked heavy class M.S. pipes including cutting, threading, welding etc. and providing all fittings e.g. elbows, reducers, clamps, hangers, flanges, gaskets, nuts, bolts and washers etc. including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade including cutting holes and chases in brick or RCC walls/ slabs and making good the same etc. complete in all respect as required. ("C" Class)

200mm dia. (5.4mm thick)

150mm dia.

100mm dia.

65mm dia.

50mm dia.

32mm dia.

25mm dia.

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : Ordinary rock Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Providing and applying one coat of 4 mm thick 'PYPKOTE' or COATEK anti rust pipe protection including approved primer of 2 coats as per manufacturers specifications and lap of 25 mm to make an impermeable layer on pipes in trenches or on structural / masonary members complete including surface preparation. 200mm dia.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing & Fixing of Yard hydrant 63 mm dia valve instantaneous female coupling on the outlet complete with flanges ,cap and chain ISI marked.

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 Code- 901(Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required.

Supply, Installation, Testing and Commissioning of 63mm 15 mtr long (RRL) Reinforced Rubber Lined Fire Hose pipe as per IS : 636 Type "A" ISI marked with 63mm male or female coupling as per IS -903 ISI marked, Binded with SS wire for SS coupling as required.

Supply, Installation, Testing and Commissioning of 63mm 30 mtr long (RRL) Reinforced Rubber Lined Fire Hose pipe as per IS : 636 Type "A" ISI marked with 63mm male or female coupling as per IS -903 ISI marked, Binded with SS wire for SS coupling as required.

Supply, Installation, Testing and Commissioning of Hose Coupling 63mm as per IS : 903 ISI Marked Item Code K-902 complete as required.

Supplying and fixing Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for installation connections to hose coupling etc. as required.

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required. 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 25 mm dia ball valve & nozzle. Drum and brackets for fixing the equipments on wall. Connection from riser with stop valve (gun metal) & M.S. Pipe.

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 600 mm x 600 mm x 450mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following: - SS single headed Hydrant valve - 1 No. Fire Hoses 63mm, 30 M long with accessories - 1 Nos. Short branch - 1 No. The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade

Supplying and fixing 2 WAY FIRE BRIGADE INLET CONNETION of cast iron body with 2 No's , Stainless Steel male instantaneous inlet coupling complete with cap and chain as required for 150mm dia MS pipe connection , conforming to IS:904 as required .

Providing and fixing of HOSE CABINET of Size: (400mm x 400mm x 450mm) made of 1.6mm thick MS sheet with 3mm thick glazed wiremesh i/c necessary locking arrangement suitable to accommodate fire brigade inlet connection duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect as required.

Supplying and Fixing Orifice Plate made of 6 mm thick,80 mm outer dia. stainless steel with orifice (internal dia.) of required size in between flange & landing valve of external hydrant to reduce pressure to working pressure of 3.5 Kg / cm2 complete as per specifications as required.

Supplying, and Fixing of Draw out connection C.I. Body having one Gunmetal 63mm male instantaneous inlets

Providing, fixing and Testing of HOSE BOX (550mm x 550mm x 450mm) for DRAW OF CONNECTION made of 14 SWG thick MS Sheet with 4mm thick glazed glass and doors including necessary locking arrangments.

Providing & fixing brass quartzoid sprinklers (UL approved) of 15 mm dia size, suitable for sustaining the pressure on the seat & water hammer effect. The type & temperature rating shall be as follows : Spray recessed (adjustable) without rossette (ss) (68 deg.C) standard sprinkler (Pendant / Upright Type)

Supplying and fixing vane type water flow switch suitable for installation on 100 mm dia line for a service pressure upto 20 kg/sq. cm.

Supply, installation testing & commissioning of 12 zone ANNUNCIATION PANEL having floor indication with individual flow switch in that particulars as per relevant IS specifications with suitable sealed maintenance free battery and charger as per the specifications and requirement of Local Fire Authority. Each and every zone should have visual indication like-Isolation, Fire, open circuit, short circuit, fire alarm acknowledged, fault alarm acknowledged. The main panel should be housed in 1.6 mm CRCA sheet steel enclosure with front door having lock and key. Each and every zone should have the following switches Isolation, fire test, open circuit test, short circuit test, fire alarm acknowledge, fault alarm acknowledge etc. as specified.

Supply, installation testing & commissioning of 150 mm dia Cast Iron installation control valve inclusive of one number 150 mm dia Butterfly valve, alarm valve with water motor gong, pressure gauges with ball valves, test valves with all necessary accessories.

Supplying, Installation, Testing and Commissioning of MS made cubicle panel made out of 1.6mm CRCA sheet powder coated with Siemens gray shade, 75x40mm channel base frame. The panel is design for wall mounting type with cable incoming and out goings from bottom suitable for cable, lock, rubber gasket, hardware etc. Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire, Copper Lugs, PVC Sleeve, Ferrules Numbers, Hardware & labour etc. All the switchgear are from L&T /Schneider/Eaton Make I.E MCB TPN 63A, Contactor MNX-18A, Over load relay 9-15A, ON /OFF indication, STOP/START push button, Auto/Manual Switch, terminal Strip, MCB 1 Pole 6 Amp, Aux. Cont., SDS Timer, SPPR complete including Starter suitable for 12.5 Hp mortar.

Supply, installation, testing and commissioning of ISI marked (IS:15638) portable fire extinguisher, ABC (gas pressure) type capacity 4kg with gun metal cap and nozzle and complete in all respects including initial fill and wall suspension brackets as required as per specifications.

Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed. 9kg capacity cylinder

Supply, installation, testing and commissioning of ISI marked (IS:15638) portable fire extinguisher, water (gas pressure) type capacity 9 litres with gun metal cap and nozzle and complete in all respects including initial fill and wall suspension brackets as required as per specifications.

Supplying and installing of 3nos set of fire buckets of 24 gauge galvanized steel sheet, standard 9 liter capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters "Fire " in black and gold.

Mechanical foam trolley mounted as per IS: 13386 type for extinguisher 50 litres capacity complete gun metal union 1 Kg Co2 external gas cartridge with wire braided discharge hose and initial charge of Aqus Film Forming Foam (AFFF) charge with all necessary fittings and accessories.

Providing and placing on terrace polyethylene water storage tank, ISI : marked, III layers with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing G.I. Tank nipple AVR/SVW Make complete in all respects. - 50mm nominal bore

Providing and fixing in position best Indian make ISI Marked Ball cock 25mm with brass rod, PVC ball complete in all respects. - 25mm nominal bore

Providing and fixing of M.S Structrual work fabricated with M.S Channel and MS Sheet for PVC tank foundation complete.

Supplying & fixing of LED type 220AC Exit sign board with Battery of suitable size as required complete. (Size : 6" x 12" ).

Bidder Name

Amount

Brij Gopal Construction Co. Pvt. Ltd.

GORA LAL BUILDER AND ENGINEER

A S ENTERPRISE

A S ENTERPRISE

Brij Gopal Construction Co. Pvt. Ltd.

Brij Gopal Construction Co. Pvt. Ltd.

A S ENTERPRISE