Supply, Installation, Testing and Commissioning of 125 KVA Generator and Connected Electrical Works at Sports Division, Kannur

Amount

Electrical works

od209789/2019_2020 : Supply, installation, testing and commissioning of 1 No. 125KVA 415 V 3 Phase 1500 rpm .8 pf water cooled floor mounted Diesel generator set l enclosed with CPCB approved acoustic enclosure, (outdoor duty) and all accessories and Stamford Alternator with rated at 125KVA and including standard control panel with suitable MCCB,CTs and transducers for all metering and protection,antivibration mountings, exhaust silencer,min 300ltr fuel capacity and exhaust pipe including the provision for fabrication of exhaust pipe to the top of the building of 4 mtrs height along with acoustic enclosure (sound pressure level as per ISO standards),electric starter, batteries ; battery charger, fuel tank with level indicator,radiator,neccesary control wiring with control cables,first fill of lubricating oil and diesel for testing and commisioning,earthing as per standards and all accessories as required complete.The work should be as per electrical inspectorate/pollution control board standards.The rate shall be inclusive of 24 months Generator Servicing and maintenance including periodical replacing of Oil , Air, and fuel filters and providing lubricant coolant as required. Make of Engine - Cummins/ Volvo/ caterpiller/ sterling wilson

od209790/2019_2020 : Supply and instalation of Exhaust Piping with B Class MS pipe of following sizes to be vent to the top of the nearest/tallest building. If the pipe cannot be clamped/ fixed to the building or any other structure of permanent nature necessary fabricated structures using channel section or angle iron sections of adequate mechanical strength duly painted with 2 coats of synthetic enamel paint over a coat of zichromate primer shall be provided for the support of the exhaust pipe 150mm dia or nearest size ;B Class MS pipe

od209791/2019_2020 : Supply ,Fabrication and fixing of AMF panel with 250A switch and provision of 6 outgoings barriers including base frame for floor mounting type panel board using channel class designation ISMC 75 including cutting welding drilling holes painting with two coats of synthetic paint over a coat of zinc chromate primer bolting the frame to the paint and also with neoprene beeding suitable SMC sheet protection to the switches,fixing of main bus bar system and earth system interconnection with Al strips with latest amendments with suitable ratings with multi function meters and with AMF relay Auto/manuel switch

2.2.1 : Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.100 Amp, 16 KA, TPMCCB

2.2.2 : Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.125 Amp,16 KA,TPMCCB

4.1.3 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.5 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.375 mm width X 50 mm depth X 2.0 mm thickness

90.12.7.27 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 25 sq.mm with factory made clamp

90.12.7.28 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 35 sq.mm with factory made clamp

90.12.7.33 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5core 150 sq.mm

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

90.16.1.2 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 2.65 mm copper conductor (12 SWG)

5.5 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earthelectrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.14 : Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.17 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

od224670/2019_2020 : Supply and fixing of Fire Extinguisher-CO2 4.5 Kg Type including with clamps

od224671/2019_2020 : Supply and fixing of Fire Extinguisher-ABC 5 Kg Type including clamps

od224672/2019_2020 : Supply and fixing of 2.00 mm thick, 3.3 kV, Synthetic elastromeric fire retardant insulating sheet

od209792/2019_2020 : Liason & co-ordination with KSEB and Electrical Inspectorate for the submission and approval of installation drawings,inspection and approval of the installation under scope of the tender,co-ordiantion with KSEB ; EI for commisioning the installation

Civil works

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.1.4 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2 : Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.4.2 : Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2

Fuji Technical Services Pvt Ltd

Bidder Name

ABM Electricals

Fuji Technical Services Pvt Ltd