CA NO CWE/AMB/SOUTH-04 OF 2025-26 SPECIAL REPAIR OF BLDG NO HT-47 HT-53 AND SM-12 UNDER B/R-I FOR GE (SOUTH) AMBALA CANTT

Amount

Demolition of brick work built in CM incl all quions arches, pillar etc all as specified and directed.

Material and labour for brick work with flyash bricks of class designation 75, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified & directed

Material & labour flyash Brickwork having class designation 75, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc complete all as specified and directed .

Taking down Cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15 mm thick on surface of any description of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:6), complete all as specified.

Rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified. NOTE:WPC will be measured and paid for separately.

Material & labour for rough cast plastering over and incl 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered. Rough cast plaster shall be applied as specified clause 14.22 of SSR Part-I .

Supply only integral water proofing comound ISI Marked complete all as specified and directed.

M&L for preparation of new plastered surface of walls & applicataion of two coats of 100% premium acrylic emulsion paint with fully automatic airless spray machine & paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance , dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @1.43 lit/10 sqm over & including priming coat of exterior primer applied @2.20kg/10 Sqm complete all as specified & directed

M&L for preparation of old plastered surface of walls including removal of existing treatment by mechanical dry wall sander machine & applicataion of two coats of 100% premium acrylic emulsion paint with fully automatic airless spray machine & paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance , dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @1.43 lit/10 sqm over & including priming coat of exterior primer applied @2.20kg/10 Sqm complete all as specified & directed

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with fully automatic airless spray machine ,over a coat of alkaline resistant primer & a coat of birla wall care putty surface having minimum thickness 1.50mm complete all as specified and directed.

Material and labour for complete removal of existing treatment on surface of walls by using mechanical dry wall sander machine for complete removal of all layers of treatment and reaching upto old plastered surface and applying a coat of wall care putty not less than 1.5mm thick as per manufacture instructions and applying two coats of oil emulsion paint with fully automatic airless spray machine over a coat of alkaline resistant primer complete all as specified and directed.

Dismantling of AC corrugated, semi corrugated sheet including ridges etc. in roof covering complete all as specified.

Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, false ceilings etc complete all as specified.

Dismantling posts or struts , truss precast section , including taking out embedded portion and making good disturbed ground

M&L Roof Trusses (framed) , trussed , purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete as all spfd and directed by EIC

S&F steel work in tubular trusses, stanchions including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 Grade St-240 complete all as specified and directed.

M&L for plates (plain and chequered) channels, square cut or notched ( ordinary and counter sunk) forming holes without any attachment of Fe-410W(gde-E-250) quality A complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

S& F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces,cooler stands etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe 310-0 complete all as specified.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

S&F mild steel sheet 1.25mm thick eaves gutters 150mm diameter, galvanised class 3 half rounded with rounded edges complete all as specified

S&F angles (internal or external) or nozzle pieces outlet of 150mm dia & 1.25mm thick galvanised sheet complete all as specifed & directed

S&F stop ends of 150mm dia & 1.25mm thick galvanised sheet complete all as specifed & directed

Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with glass fibre reinforced gypsum false ceiling tiles of size 595x595 mm of approved texture, design & patterns having moisture content less than 2%, humidity resistance of 99% , NRCO 0.50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (part 4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @120 gms per sqm on both sides) comprising of main T runners of size 15x32mm of length 3000mm, cross T of size 15x32mm of length 1200mm & secondary intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600x600mm , suspended from ceiling using galvanised mild steel item (galvanising @ 80 grms per sqm) ie 50mm long , 4mm dia GI wire fixed with necessary hanging arrangement as per manufacture instructions. Galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm centre to centre & 40mm long dry wall wood screws . The work shall be carried out as per specification , drawings & direction of Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr in Charge.

Demolition of Cement Concrete as in G.F & paving n. exc. 15cm thick (above or below ground level) complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour for 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note:- The plinth protection shall be laid in panels and lenth of each panel shall not be more than 2.00 m all as directed 6mm joints filled with 85/25 grade bituman and sand in the ratio (1:3) shall be provided.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:6) complete all as specified and directed.

Material and labour for premium quality coloured glazed ceramic tiles (350 x 250 x 7 mm thick / 450 x 300 x 7 mm thick) and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match including rendering 10 mm thick in cement plaster 1:4 as in vertical surfaces complete all as specified and directed.

Material and labour for 16 to 18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick cement mortar (1:4) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, polishing, rounding and moulding of stone slabs on edges, complete all as specified and directed.

Taking down chowkaths or frames n.exc 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc

Taking down chowkaths or frames exc 1.5 sqm but n exc 4.0 Sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc

Supply and fixing of mild steel 300 mm, helical door spring with roller plate for door shutter including welding if necessary fixed in repair complete all as specified and directed.

Supply and fixing of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 150mm complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Ltrs per Sqm of the vertical surfaces of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed. Note : Quantity will be measured perimeter of wall x depth of penetration.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position including MS hold fast/lugh/SS dash fasterners of required dia & length complete as per direction of Engr-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. Note: Material Test Certificate & Authentication should be provided by the manufacturing company.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification colour WOOD COLOUR complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. Note: Material Test Certificate & Authentication should be provided by the manufacturing company.

Supply & fixing of stainless steel butt hinges 100 mm long medium weight complete all as specified & directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) complete all as specified and directed. Note: Material Test Certificate & Authentication should be provided by the manufacturing company.

Providing 30 mm thick Factory Made 100% Solid WPC ( Wood polymer Composite ) gauzed and skeleton Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ),alcium Carbonate andnatural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheetSingle Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured and an ISO 9001 -2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. rate inslusive for Fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws incl Aluminum Jali and Stainless wiremess as per required. complete all as specified and directed. Material test certificate and authentication should be compulsory provided by the manufacturing company

Supply & fixing stainless steel (ISI Mark) handle extruded fabricated type handle 100mm long complete all as specified & directed.

S&F 150 mm long stainless steel (ISI Mark) tower bolts of extruded section and fixed complete all as specified & directed.

Supply & fixing stainless steel (ISI Mark) handle extruded fabricated type handle 150 mm long complete all as specified & directed.

S&F 200 mm long stainless steel (ISI Mark) tower bolts of extruded section and fixed complete all as specified & directed.

Supply & fixing stainless steel (ISI Mark) sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing with bolts extruded sections complete all as specified & directed.

S&F Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2 Nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes. (Make: A2Z Infra Solutions/ Elixir Metform Pvt Ltd./ Lakshmi Fabrications)

S&F Providing & fixing of ventilators made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished with suitable provision as in ventilator in toilet/bathroom/staircase (Make: A2Z Infra Solutions/ Elixir Metform Pvt Ltd./ Lakshmi Fabrications)

Material & labour for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide primer incl preparation of new surfaces complete all as specified and directed by Engr-in-charge

S&F in repair of 4.0mm dia plain mild steel wire galvanised class 3 for hanging arrangement for mosquito net ,including securing hanging including straining and fixing to wood ,concrete or steel hooks to or with straining bolts including necessary arrangement as per site requirement complete all as specified and directed.(Each line of wire to be measured).

S & F stainless steel curtain rod 25mm dia having wall thickness 1.6mm fixed with and including stainless steel decorative brackets, two lotto for each road length at both end etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair SS peg set of 5 size 300x20x2.5mm all as specified and directed.

Taking down of Eaves gutter/rain water pipe( AC rain water pipe /SWG pipe line of any size or pattern), incl all fittings, complete all as specified.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site

Supplying and laying of CPVC pipes 20mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supplying and laying of CPVC pipes 16mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends of edges of landings, steps, cills etc., and cutting chases for concealed water tubing and making good complete.

S&F in repairs,Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe, P or S trap,) all as specified.

S&F in repairs for PVC water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

Supply & fixed in repairs vitreous China squatting pan of “Orissa Pattern” of size 580x440mm coloured with integral footrest complete including making good floors complete all as specified.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe all as specified.

Supply and fixed in repair counter top wash hand basin padstel pattern vitreous china of size 520x410x150mm of Model Inslim 515 C041L of Parryware or equivalent including SS bottle trap complete all as speciifed & as directed

Supply and fixing in repair pillars taps fancy type chromium plated cast copper alloy with capston head long screwed shanks of 15mm bore compete all as specified.

S& F in repair health faucet ABS body with 1 metre long stainless steel tube and wall hook.

S& F as in repair JET spray (Butterfly) with flexible 1 mtr tube complete for EWC as all specified and directed.

S& F in repair Chromium plated toilet paper holder.

S & F in repair Two way angle cock with flange chromium plated of bore 15 mm complete all as specified and directed. Make:- Prayag :- Cat NO:- 7811-N or equivalent.

S&F in repair Bib tap, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, suitable for 15 mm bore pipe, complete all as specified.

Supply & fixed in repairs stainless steel grating openable 100mm size with/without hole including fixing with white cement complete all as specified.

Supply and fixing in repair Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair 20mm bore Gun-Metal, globe or gate valves , with iron wheel head,screwed down both end for iron pipe and fixed all as specified and directed by Engineer-in-Charge.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm th sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long.

Supply & Fix in repair Soap dish any type, fixed to plugs with chromium plated brass screws.

S & F in repair chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

S&F in repair for PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed.

M&L for 75mm dia PVC (SWR) vent cowl complete all as specified and directed

M&L for Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and directed.

S & F for 32 mm bore Waste coupling of PTMT (half full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms)

S&F PVC waste pipe 32mm dia complete all as specifed and directed.

Supply and fixing of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing of water storage tank of 1000 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore complete including dismantling/ taking out of old water tank & removing from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

M&L stack clamps of 50mm by 5 mm flat iron and 16 mm dia round iron stays, incl bolts & nuts and securing ends of stays to wall or roof for 100/110 mm bore CI/PVC Pipe complete

S&F for 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including dismantling of existing AC pipes of any description any length complete all as specified and as directed..

Supply and fixing PVC (SWR) 75 mm pipe type A single socket in any length with rubber ring joints laid in floors or trenches including dismantling of existing pipes of any description any length complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends 110 mm bore complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends 75 mm bore complete all as specified and as directed.

Supply and fixing of 110 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing of 75 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing in repair of PVC (SWR) floor trap, plain with grating including jointing with solvent cement of outer dia metre outlet of 75 mm complete all as specified and directed.

S&F in repair for vitreous china bowl urinal flat back, size 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Demolition and breaking up 150 mm bore drain pipes (salt glazed stone ware pipes) set in cement mortar complete all as specified.

M&L for Concrete bed to drain pipes of 150mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified

S&F for 150mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches including dismantling of existing pipes of any description any length complete all as specified and as directed.

M&L for salt-glazed stoneware gully traps,150x150 square or round mouthed, type "P" setting and jointing to drains with cm 1:1.

Excavating in post holes (or similar holes) each n.exc 0.50 Cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in any type of soil complete all as specified and directed.

M & L for PCC (1:3:6) type C2 by using 40 mm well graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

S&F Mild steel TMT bar 10mm dia and over cut to length bent to shape required, including cranking bending spirally and binding with and including mild steel sire (annealed) not less than 0.9mm dia all as specified and directed.

Demolition of RCC n exc 15cm thick in any position complete all as specified & directed

M&L for RCC (Nominal Mix) type B-0 1:2:4 (using 12.5 mm graded aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Dismantling Timber scantling 40 Sq cm and over in any position all as specifide and directed

M &L for PCC 1:4: 8 type-D2 as in sub base to floor 100mm thick using 40mm graded aggregate complete all as specified & directed

S & F Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with Grey cement & pigment

Sand filling under floors or in foundation including watering & consolidation 25mm thick complete

M&L PCC type B0 (1:2:4) in lintels clear span, cills, steps, seismic & other similar bands, coping, kneelers, apex stones , bed plates , water troughs & like including weathering slightly rounded or chamfered angles and throating as directed

M/L for 40mm PCC type B-1 1:2:4 (20MM graded aggregates as in flooring complete all as specifide and directed

M/L for 75mm PCC typeD-2 1:4:8 (40MM graded aggregates as in sub base flooring complete all as specifide and directed

M&L machine cut pre polished kota stone slab flooring minimum size 55x55 cm 18-20mm thick over cement screed base 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L pre polished kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed base 10 mm thick in CM 1:4 including rubbing and polishing complete

Material and labour for applying waterproof cement based putty @0.80kg (undiluted) per sqm of average thickness 1.50mm in two coats on prepared / newly plastered wall (external/ internal) and ceiling surfaces as per item No 2,3,4,6 in following steps- (i) Filling cracks in wall using crack seal compound Asian smart care crack seal or equivalent (ii) Mix the putty @ 0.6 kg/sqm by adding 35 to 40% water by volume or as per approved manufacturer's instructions & mix it with electric putty mixer with mixing capacity of min 2.5 kg putty per minute upto 5 to 10 minutes (iii) Allow 6-8 hrs to dry putty surface then prepare the surface by electronic wall sander machine to apply subsequent coats of primer complete all as specified and directed.

Material and labour for applying two coats of anti fungal weather proof grade exterior acrylic emulsion paint of approved tint @1.80 lit / 10 sqm (undiluted) as per approved manufacturer's instruction over prepared and primed surface of external wall. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed. MAKE : - Apex Ultima Protek Asianpaints / Nerolac excel top guard / Berger weathercoat long life 10.

Supply and fixing (in repair) aluminium alloy anodized (powder-coated) door frame and partly glazed shutters with hollow aluminium anodized sections including 6mm thick plain coloured bakelite sheet or acrylic boards, prelaminated both side with one side decorative choice lamination for fixing in bottom panel as specified including aluminium alloy anodized snap type beads, dish type door handles, glazed clip, jointing cleats, rubber packing, gasket, dead lock 4 levers, 02 Nos aluminium alloy anodized tower bolts to each leaf etc. including fixing frame to wall/RCC members etc. with rawl plugs complete all as specified and directed. Sections of frame and door shall be as follows : - (a) Door Frame single groove 101.6 mm x 44.45 mm x 2.15mm thick (b) Shutter top 47.62 mm x 44.45 mm x1.95 mm thick. (c) Shutter bottom 114.30 mm x 44.45 mm x 2.1 5mm thick. (d) Shutter vertical 85 mm x 44.45 mm x 1.80 mm thick. (e) Shutter middle 83.5 mm x 44.45 mm x 2.40mm thick. (f) Gauging clip weighing not less than 0.097kg/metre. Notes :- 1. Glass pane shall be measured and paid separately. 2. Manufacturersof section : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or equivalent make as specified in appendix B.

Supply and fixing (in repair) aluminium alloy anodized (powder-coated) window frame with double shutters open able type, with aluminium sections as specified for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, stainless steel hooks and eyes, aluminium anodized barrel tower bolts, glazing clips, joint cleats, rubber packing, gaskets etc for series-B “ Jindal” section numbers for casement window.complete all as specified and directed comprising of followings :- (a)Frame of section 101.6mm x 44.45mm x 2.10 mm thick and section for shutter 47.62 mm x 44.45 mm x1.95 mm thick. (b) Mullion 53 mm x 52 mm x 2 mm thick not less than 1.065 kg/mertre. (c) Glazing clip weighing 0.259kg/mtr. (d) Window shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98 mm and thickness 2.37mm weighing 0.875kg/mtr and 01 no for each open able leaf. Notes :- 1. Glass pane shall be measured and paid separately. 2. Manufacturersof section : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or equivalent make as specified in appendix B.

Material and labour for 5 mm thick rendering in cement mortar (1:3) on brick or concrete ceiling surface of any description, finished the surface even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of old decorated wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old decorated steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

All same as item above as in vertical surfaces of skirtings but over 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs Steel ventilators, fixed type, with glazing bars including dismantling complete all as specified.

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane

Supply and fixing 5.5 mm thick tinted glass in square exc 0.5 sqm in each pane with heat reflecting properties , fixed to aluminium frame with glazing clips, etc., complete all as specified and as directed.

Description all as per item No. 2 above but except bricks including cleaning, removing mortar from the bricks complete all as spd in CM 1:6

S&F(in repair) 0.80 mm thick mild steel plain black sheeting as in covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified.

Taking down carefully aluminium/ copper point wiring (light, fan,socket or power) complete, including fixtures and fittings such as switches, ceiling rosees, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of walls,ceilings etc.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and including PVC conduit not less than 20mm dia with and including accessories, concealed on wall/ and surface on ceiling and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI metal flush boxes made out of 1.2mm thick of any module from 2 to 18 module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 including modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over metal flush boxes for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / Bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH (FIRE Retardant Low Smoke and low Halogen) copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed. NOTES:- 1. Switch, socket and fan regulators to be measured and paid for separately. 2. All chases will be cut by chase cutter only.

Description all as per item No 131.00 here in before but for socket out let point 6 Amps on same board

Description all as per item No 131.00 here in before but for socket out let point 6 Amps on independent board

All as per srl item No 131.00 above but point wiring for one socket out let 16 & 6 Amps (independent) controlled by one switch with using 2.5 Sq mm (nominal area) stranded copper conductor

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified.

Supply and fixing modular switches, one way, 6 amps one module, 230V, 50 Hz supply, complete all as specified and directed.

Supply and fixing modular switches, one way, 16/20 Amps, one module, 230 volt , AC supply, complete all as specified and directed.

Supply and fix modular socket outlet 6 amps, 2/3 pin combined 2 module, 230 volt, complete all as specified and directed.

Supply and fix modular socket outlet 6/20 amps,3 pin, 2 module, complete all as specified and directed.

Supply and fix modular fan regulator step type one module, 100w 230 Volts, 50 Hz, AC complete all as specified and directed.

Supply and fixing of LED luminaries of capacity 20 watt integrated aluminium batten with including Oppel diffuser complete including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and as directed.

Supply and fix surface mounted LED tube light fitting with high efficient diffuser mirror light, aluminium housing in CRCA body suitable and including 10 watt LED tube high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light complete all as specified and directed.

Supply and fixing Bulk Head Fitting 10 Watt and connected with copper conductor cable of size 1.50 Sqmm, for fixing the light fitting complete all as specified & directed.

Supply and fix in repair recess mounted LED flat panel 2' x 2' with high efficient LEDs and glare free full decorative light fitting, 36 watt, energy efficient provided with including LED 36 watt with provision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting complete all as specified and directed.

Supply and fix bracket for security light made up of 25mm dia,0.9m long GI pipe, light grade, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed.

Supply and fix LED security light luminaire 30/35 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP65 protection, better optics for uniform distribution with multiplte LEDs not less than 2 W eachand having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with Two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down old unserviceable security light fitting of any description and in any position complete all as specified and directed.

Material and labour for taking down existing lighting fiting any type/size/Make/capacity i.e T/L, Surface/ Recess Panel, flame proof, wall light, bulk head, mirror light etc and re-fixing the same after minor repair/cleaning including replacement connection wire with suitable size coper wire twin core 0.75 sqmm for connection from ceiling rose to light fitting complete all as specified and directed.

Supply and fix sheet metal enclosure SP with two pin and earth plug and socket with one single pole, MCB 20/ 32 Amps, 'C' curve, 240 volts including taking down existing sheet metal enclosure of any size & cap complete all as specified and directed.

Supply and fix sheet metal enclosures vertical distribution board VTPN,(MCCB DB) 4 ways, double door , 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole adjustable thermal release type ,125AMPS ,25 KA as incomer and MCB s as out going complete with making suitable size of MS cabinet 1.2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and directed.

Supply and fix sheet metal enclosures vertical distribution board VTPN,(MCCB DB) 4 ways, double door , 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole adjustable thermal release type ,100 AMPS ,16 KA as incomer and MCB s as out going complete with making suitable size of MS cabinet 1.2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and directed.

Supply and fixing in repair SPN distibution board 8 way, double door, IP 43, as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles complete all as specified and directed.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SP and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning.

Material and labour for sub main wiring with two single core FRLSH, PVC insulated unsheathed copper conductor cable 6.0 sq mm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 6.0 sqmm,green colour for earth continuity conductor including including taking down old unserviceable sub main wiring and making good the disturbed surface complete, all as specified and directed.

Point wiring for AC using approved colour coding as per IS with stranded copper conductor 4 Sqmm (nominal area ),single core ,FRLSH PVC insulated and unshaethed stranded cable 1100 volts grade ISI-694 marked in and including heavy duty ,PVC concealed conduit ISI marked for one industrial type metal clad earth plug and socket out let with earth dolly including FRLS PVC Insulated unsheathed copper conductor 4 Sqmm nominal cross section area as earth continuity conductor upto common earth and connecting to common earth dolly complete and including cutting/chasing of wall complete all as specified and directed by Engg in Charge.

M& L for taking down ceiling fan any type, taking in safe costudy and refix the same after completion of repair work including servicing, provision of cable from ceiling rose and painting with synthetic enamel paint by sparying including filling cavities with filler, one coat after cleaning all dust all as specified and directed.

Taking down unserviceable ceiling fan/ Exhaust fan any size or any type and deposited to concerned AGE E/M store yard complete all as specified and directed.

M& L for hanging only ceiling fan/ Exhaust fan (taking down for repair work) including provision of cable from ceiling rose after servicing and painting with synthetic enamel paint by sparying including filling cavities with filler, one coat after cleaning all dust all as specified and directed.

Taking out old unserviceable earthing and material & labour for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron wire of size 4.0 mm as earthing lead (upto terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 40 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh , RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 1991(Part-I) complete all as specified and as directed by Engineer-in-charge. Note : The rates for earth work, GI protection pipe, funnel, wire wesh, CI cover, etc shall be deemed to be including in quoted rates.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, heavy duty electric cable 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, heavy duty electric cable 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core as specified and directed.

Supply and laying of LT undergroung cable, XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 6 Sqmm 2 Core with suitable size of PVC Concealed/ surface conduit along with necessar fixing accessories complete all as specified and directed.

Supply and fixing for GI protection pipe of 50mm dia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation, shafts, man holes, laying of cable etc not exceeding 10 Square metre on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soil of any description, complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50 metre and deposited where directed at a level not exceeding 1.5m above the starting point, complete all as specified and as directed.

Material and labour for unwashed dry sand cushioning for cable protection ,filling in trenches/ducts, complete all as specified and as directed.

Material and labour for old size bricks sub class 'B' for cable protection laid along length of cable complete all as specified and as directed.

Supply and fix Gate light in Aluminum die cast with modern artistic design and white PC diffuser suitable with 7-8 Watt LED, with top portion square/ round and accessories internally pre wired and including connecting up with suitable size of flexible copper conductor cable including disconnecting and taking down existing light fitting and removal complete all as specified and directed. Note : Rates are including fixing of gate light, suitable size of GI pipe with fixing arrangement all as specified and directed by Engineer- in- Charge.

Note:- Amount of credit of Rs. 1,56,205.50 for retrieved materials is mentioned in Schedule of Credit Page No. 24 & 25 of tender documents in pdf form which will be deducted offline while acceptance of tender.

S M BUILDERS (BID ID -3406193)

Bairagi Builders (BID ID -3405537)

Parveen Kumar (BID ID -3399090)