SPECIAL REPAIRS TO BUILDING NO. P-47/48 (VEHICLE PARKING FOR AUDITORIUM), TOILETS (02) AND RECEPTION AT MAIN GATE, PROVISION OF COVERED PASSAGE FROM AUDIT BUILDING TO ADMIN BUILDINGS, PROVISION OF CONCERTINA COIL FENCING OVER SECURITY WALL AT PCDA (A

Amount

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete in floors and paving exc 15cm thick above ground floor (sunken floor) including picking, sweeping cleanng with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material and removing the demolished material outside the MoD land complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not other wise specifically provided for complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlarfacings, dressed stonework and precast concrete article complete all as specified and as directed.

Taking down cement or cement lime plaster,any descriptio on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and as directed.

Excavation in trenches n.exc. 1.5m wide and n.exc. 1.5m depth for foundation and getting out in loose/soft soil complete all as specified and as directed.

Excavating overareas, n.exc 1.5m deep and getting out in any type of soil complete all as specified and as directed.

Excavating overareas, exc 1.5m and n.exc 3.0m deep and getting out in any type of soil complete all as specified and as directed.

Returning, filling in incl spreading levelling watering and well ramming in layers n.exc 25 cm as in soft/ loose soil complete all as specified and as directed.

Removing excavated material n.exc 50m and depositing where at a level n exc 1.5 m above the starting point in soils complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40mm grade crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for concrete in Sunken floor and vertical faces of walls to ease up about corners with cement concrete (1:2:4) type B0 (using 12.50mm crushed stone aggregate) mixed with SBR Latex liquid polymer (mixed as per manufacture instructions & will be paid under relivnt item of Sch A) including using form work (straight or curved) as required complete all as specified and as directed.

Excavating in post holes (or similar holes ) each n exc 0.5 cum , getting out ,returning ,filling in and ramming earth or broken rubble mixed with earth around ,in layers not exc 25cm, watering and removing surplus soil to a distances n exc 50m and making good surface in hard/dense soil complete all as specified and as directed.

M&L Cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) in foundations, post hole, filling and mass concrete etc complete all as specified and as directed.

M&L for Brickwork with subclass‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed.

M&L 15mm thick rendering in CM (1:6), on fair faces of brickwork or concrete surfaces ,surface finished air and even without using extra cement complete all as specified and as directed.

M&L Rendering 5mm thick on air faces of brickwork or concrete surface in CM(1:3) in ceiling complete all as specified and as directed.

M&L for preparing of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for preparing of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L 75mm thick PCC (1:4:8) type -2 (using 40mm grade crushed stone aggregate) as in sub base complete all as specified and as directed.

Taking up or down steel tubing and connections,15mm bore hole including removal complete all as specified and as directed.

S&F 15mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and as directed.

S&F 20mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete all as specified and as directed.

S&F in repair 15mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and as directed.

S&F in repair 20mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and as directed.

M&L Vitrified coloured tiles 8-10mm thick any Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 laying floor finishes complete all as specified and as directed.

M&L Vitrified coloured tiles 8-10mm thick Dark Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) to recieve tiles complete all as specified and as directed.

M&L for joint free Non skid ceramic coloured tiles 7-8mm thick (square/rectangular), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, over and including 15mm thick screed bed in CM (1:6) in flooring, set and jointed in neat cement slurry and pointed in white coloured including 15mm thick screed bed in CM (1:6) finish surface rough to recieve tile complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles of size 300x450x7mm thic on wall set and joined in neet slurry and pointe in white or coloured cement to match the shad of tiles includind 10mm thick rendering in CM (1:4) finish surface rough to recieve the tiles dismantling floor, hearth or wall including bedding ( but not backing) rubbish off the permises complete all as specified and as directed.

S&F in repair vitreous china white wash basin, wall hung type with complete accessories, half pedastal, excluding tap but including brackets complete all as specified and as directed. Make : Jaquar Cat Part No. LYS-WHT-38801 and pedestal Cat part No. LYS-WHT-38805 or equivalent quality in Parryware or Cera as approved by GE.

S&F in repair vitreous china white wash down couple closet composite type including PVC Soft seat cover white complete all as specified and as directed. Make : Jaquar Cat No. ONS-WHT-10853S or equivalent quality in Cera or Parryware as approved by GE.

S&F in repair Vitreous china squatting pan ‘Orissa pattern’ size 580x440mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified and as directed.

S&F in repair 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and as directed.

S&F Vitreous china wash down water closed pan (Pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F bottle trap (with internal partition) 32mm dia size with 250mm and 190mm long wall connection & wall flange complete all as specified and as directed. (Make : Jaquar Cat Part No. ALD-769L 250x190 or equivalent in approved make of Hindware/ Cera/ Parryware as approved by GE.)

S&F in repair CP Towel Ring 200mm dia round with round flange complete all as specified and as directed. (Make : Jaquar Cat Part No. ACN-1121BN or equivalent in approved make of Hindware/ Cera/ Parryware as approved by GE.)

S&F in repair 15mm dia CP stop angle valve fancy type with long shank and cup etc complete all as specified and as directed. Make : Jaquar Cat Part No.- FLR-5053N or equivalent in Parryware or Cera as approved by GE.

S&F Toilet paper holder stainless steel flap fixed to wall etc complete all as specified and as directed. (Make : Jaquar Cat No. ACN -1153N or equivalent in Parryware/ Cera as approved by GE.

S&F Soap dish, fancy type complete all as specified and as directed. Make : Jaquar Cat Part No. ACN-1131N or equivalent make in Cera/ Parryware as approved by GE.

S&F PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and as directed.

S&F in repair Hand Shower (Health faucet) with 8mm dia 1.20m long flexible tube & wall hook with NRV including fixing bracket complete all as specified and as directed. Make : Jaquar Cat No. ALD-577 or equivalent in approved make of Cera/Hindware/Parryware as approved by GE.

S&F in repair Vitreous China white half stall urinal of size 330x345x 610mm top inlet fix with necessary brackets including 32mm dia CP waste coupling, suitable brass chromium plated urinal spreader, waste pipe etc complete all as specified and as directed. (Make : Jaquar URS-WHT-13257 or equivalent make in Cera/ Parryware as approved by GE.)

S&F in repair 100mm size cockroach proof CP grating fixed with coloured cement in floors, joints to match the existing surface of tile complete all as specified and as directed.

S&F in repairs pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. (Make : Jaquar Cat part No. FLR-5011N or equivalent make in Parryware or Cera as approved by GE.)

S&F 12mm thick toughened glass plain or tinted, in partition and the like fixed with stainless steel clamp over floor/wall complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and as directed.

All as per item 51 above but exc 1.5 Sqm but not exc 4sqm each complete all as specified and as directed.

Supplying frame of size (100mm x 63mm, single rebate) Factory made 100% Solid WPC Brown door Frame made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and as directed.

Supplying frame (125mm x 63mm Double Rebate) Factory made 100% Solid WPC Brown door Frame made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and as directed.

Supply and Fixing shutter of 24mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and as directed.

Supply and Fixing shutter of 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and as directed.

Supply and fixing shutter of 30mm thick Factory made Wiremesh SOLID PVC Door Shutter Consisting of frame made out of M.S.tube of 19 guage thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rail. M.S Frame shall have a coat of metal primer of approved make and manufacturer 19mm x 19mm M.S square tubes shall be covered with 5mm thick PVC heat moulded (100% LEAD FREE) plain sheet 'C' channel 75x30x60 out of 10mm shall be heat at 90 deg. towards inner site of both site of both face of the door forming stiles for top, bottom, lock rails shall be fitting of 10mm inner site all rails (T,B lock) shall be covered with 100mm wide PVC sheet S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be remove or fix again after changing of wire mesh when needed complete all as specified and as directed.

S&F Aluminium powder coated three track sliding windows (with three sliding shutters, (One with and incl stainless steel wire mess and two with and incl 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per meter for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame 0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides 0.45 kg per metre including suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles etc complete all as specified and directed. Windows shall be provided with guard bars using 25mm flat iron and 10mm square bars of design including painting of guards bars complete all as specified and as directed.

S&F aluminium powder coated fixed glazing with alumium frame of weight not less than 1.2kg/m with and incl 5mm thick glass (plain /tinted) size as directed by engineer in charge including suitable nylon beading channel gasket ,etc complete all as specified and as directed.

S&F in repair 18mm thick WPC board one side prelaminated and other side plain white colour as in cup boad shutters and frames, kitchen cabinet front shutter, partion, shelf & drawer, fixed with screws, solvent cement/ adhesive complete all as specified and as directed.

S&F Butt Hinge 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin ,anodised and fixed, type C-21 complete all as specified and as directed.

S&F 150mm size Stainless Steel Handle complete all as specified and as directed.

S&F 150mm long,aluminium,anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F in repair door closer aluminium (extruded section) body hydraulically regulated, designation No. 3, universal type complete all as specified and as directed.

S&F in repair Hydrulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and as directed.

M&L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 20 mm thick in CM (1:6) complete all as specified and as directed.

S&F in repair 110mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and as directed.

S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and as directed.

S&F in repair 75mm dia PVC (SWR) floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and as directed.

M&L for cutting chases ,pinning in making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landing ,steps cills sunshades,sheives lintels etc and cutting chases for concealed water pipes etc and making good cutting not exc 10cm complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa and 150AZ as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa and 150AZ as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and as directed.

S&F Rolled mild steel work of Fe-290 (Gde E-165) as in framed work, trussed, purlins, crane gantries, rails & fastenings and heavy bracket framing (Beam, tee, angle, Tubular Pipe, channel or flat sections etc.) including distance pieces, cleats etc complete all as specified and as directed.

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and as directed.

M&L 100mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80mm thickness M-40 grade with grey cement and pigment complete all as specified and as directed.

M&L for rubber moulded coloured glossy finish cement concrete chequered tiles of size 30cm x 30cm x 20mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over 15mm thick screed bed in CM (1:6) including dismantling of existing tiles complete all as specified and as directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) for fixing edge of Chequered tiles and rounded or chamfered edges, coping complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channels and drains finished fair and even complete all as specified and as directed.

M&L 15mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and as directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide ® rough finished surfaces of concrete complete all as specified and as directed.

M&L for reinforced cement concrete (Nominal Mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in cover slabs incl neccesary formwork set in cement mortar (1:4) complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L mild steel TMT bars 5mm dia and over upto an including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B2 (using 40mm graded crushed stone aggregate) as in surface channels and drains finished fair and even complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (using 20mm graded crushed stone aggregate) as in sub base of floor laid in panel complete all as specified and as directed.

M&L for reinforced cement concrete (Nominal Mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of weather proof exterior paint over a coat of suitable primer complete all as specified and as directed.

M&L for Complete removal of existing treatment and applying two coats of weather proof exterior paint over a coat of suitable primer on old decorated wall surfaces complete all as specified and as directed.

S&F joist channel, angle or tee section by welding fixed independently without connecting plates etc. in fening post & gates etc complete all as specified and as directed.

S&F Concertina coil, galvanised 600mm dia, stretched over barbed wire and angle post, 60 spirals/12 mtr and 3 Nos of clips per spiral as per manufacturer's instructions complete all as specified and as directed.

M&L for PCC (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as in ;intels upto 1050m clear span, cills, steps, seismic and other similar bands, plinth courses, lacing courses, string courses, parapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, hold fast blocks, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for 75mm thick PCC (1:2:4) type B-2 (using 20mm graded crushed stone aggregate) as in sub base of floor laid in panel complete all as specified and as directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and as directed.

Material and labour for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of CI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS ) as earth wire connected with main common earth dolly complete all as specified and as directed for the following :-

One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp.

One 3pin/5pin 5 Amps socket out let on same board controlled by one, one-way Piano type switch complete all as specified and as directed.

One 3pin/5pin 5 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all as specified and as directed.

All as per item No 99 above but with 2.5 Sqmm PVC insulated cable (FRLS ) for 15 Amps power point complete all as specified and as directed.

Supply and fixing switch piano flush type single pole, one-way 5 Amps, 240 Volts AC complete all as specified and as directed.

Supply and fixing switch piano flush single pole, one-way 15 Amp, 240 Volts AC complete all as specified and as directed.

Supply and fixing socket out let 2 in 1,3 pin 5 Amps flush type complete all as specified and as directed.

Supply and fixing socket out let 2in1.3pin 5 Amp and 15 Amp flush type (multi) suitable for 240 Volt AC complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals complete all as specified and as directed.

S&F batten/angle holder insulated body wwith back plate suitable for batten fitting complete all as specified and as directed.

S&F LED lamp 9 watt complete all as specified and as directed. (Make: Wipro/Havells/Crompton or equivalent as approved by GE.)

S&F LED tubelight 20 watt with integrated driver, polycarbonate diffuser & aluminum housing complete all as specified and as directed. (Make: Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS/HPL Cat Part No HLPT51520CW/ C&S Cat Part No LTTB4f20WLEDP/W or equivalent as approved by GE.)

S&F LED mirror light 10 watt 600 mm long with integrated driver, polycarbonate diffuser & aluminum housing complete all as specified and as directed. (Make: Havells Cat Part No. LUMILINEPLUSBS10WLED865SPCSS/HPL Cat Part No HPLT51510CW /C&S Cat Part No LTTB2F10WLEDP/W or equivalent as approved by GE.)

S&F PVC fresh air exhaust fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as specified and as directed. (Make: Bajaj/Havells/Crompton/Usha or equivalent as approved by GE.)

S&F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body including louvers and cutting as required size and shape complete all as specified and as directed. (Make: Bajaj/Havells/Crompton/Usha or equivalent as approved by GE.)

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed. 2. Unless otherwise specified the rates for PCC/RCC shall deemed to include the cost of formwork shuttering etc., required for complete and proper execution of the work. Refer Schedule "A" notes for details.

M/S P K ARORA