CA NO GE(N)AMB-07/2021-22 REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND OTHER CONNECTED BLDG REPAIR WORKS IN JCO/OR MD-I ACCN IN THE AREA OF AGE B/R-II UNDER GE (NORTH) AMBALA CANTT

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M & L taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 10 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases ,pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exc 5 sqm each patch including removal of rubbish/demolished material to a distance exc 250metre and not exc 500 metre , including scaffolding up to 3.00 metre height including two coats of cement base paint complete all as specified and as directed by Engineer-in charge .

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exc 5 sqm each patch including removal of rubbish/demolished material to a distance exc 250 metre and not exc 500 metre, including scaffolding exc. 3.00 metre and not exc 7.00 metre height including two coats of cement base paint complete all as specified and as directed by Engineer-in charge .

Taking down loose plaster from ceiling surface, cleaning with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exc 3 sqm each patch including removal of rubbish/demolished material to a distance exc 250 metre and not exc 500 metre, including three coats of white lime wash complete all as specified and as directed by Engineer-in charge .

M & L preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over a coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of newly plastered/unplastered surfaces of brick/concrete wall and applying two coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with and including decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F bib taps 15mm bore fancy type brass chromium plated with long body screwed down for iron pipe and fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F of fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy angular type chromium plated stop valves, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC with complete accessories as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen with plugs, waste pipe, brass chromium plated coupling and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L glazed ceramic coloured tiles joint free 1st quality in vertical surfaces/skirtings/dados of size 350x250x7mm/450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregates as in sub base of floor and finished even and fair to receive tiles etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L 18 mm thick MDF board prelaminated exterier grade (grade-1) confirming IS 14587, fixed with nails for kitchen cupboard and cabinet ,shelves for cupboard , frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards complete all as specified and as directed by the Engineer-in-Charge.

M & L 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing & adjusting shutters of any description n exc 1 sq. m each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing & adjusting shutters of any description exc 1 sq. m and not exc 2 sq. m each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge.

Taking down steel door shutter from the frame exc 1.00 sqm but not exc 2.00 sqm each and refixing in the same opening by cutting, welding as necessary including adjusting as per opening complete all as specified and as directed by the Engineer-in-charge.

S & F factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

S & F factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-W(Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

M & L PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, guard bars and painting etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete all as specified and as directed by Engineer in Charge. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill as shown on drgs. (iii) Glazing, wire mesh shall be measured and paid for separately.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel butt hinges 100mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 150 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

S&F 32 mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc complete all as specified and as directed by the Engineer-in-Charge.

Taking out and demolition of mass concreting including flooring from the sunken portion and removel of the same to a distance n. exc 1.50 KM complete all as specified and as directed by the Engineer-in-Charge

M&L for cement concrete type E2, 1:5 10 using 40 mm graded crushed stone aggregate as in sunken portion ,fdn filling and mass concrete complete all as specified and as directed by the Engr-in-charge.

Material and labour for 15mm thick cement plaster in cement mortar 1:4 mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction and applying one coat of hot bitumen of Gde 85/25 @ 1.20 Kg/Sqm over and including bitumen primer coat @ 0.30 ltrs/ Sqm as in sunken floor etc complete all as specified and as directed by the Engineer-in-Charge. Note:- cost of WPC shall be be deemd to be included in quoted rate.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC(SWR) bends of any radius, for 110mm bore pipes, with access doors complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius with access doors complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

S & F 500 litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed by the Engineer-in-Charge Note:- Tank shall be in white colour.

S & F 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight-200 grm) complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting existing water tanks of capacity exc. 250 ltr and not exc. 500 ltrs setting aside(or lowering if required) for repair, cleaning, etc. and hoisting if required reconnecting and refixing in position. (cleaning repairing, etc. measured separatly) complete all as specified and as directed by the Engineer-in-Charge.

S & F 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel butt hinges 100 mm long as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel butt hinges 75 mm long as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed as in repaircomplete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long aluminium handle fabricated type anodised as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs stainless steel grating cover 100mm die, fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair waste coupling fittings 32mm dia of brass, chromium plated for glazed ware sink, basins etc. with long screwed shanks and fly nuts flange end bedded in red lead cement complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair waste coupling fittings 38mm dia of brass, chromium plated for glazed ware sink, basins etc. with long screwed shanks and fly nuts flange end bedded in red lead cement complete all as specified and as directed by the Engineer-in-Charge.

M & L for running welding in repairs, Thickness of metal to be welded not exc 6mm, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of plain or corrugated steel sheet of any thickness incl Nainital or similar pattern coverings, complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, Az-150 coating as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S&F Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I S.1161-1979 grade St.-240 including dismantling wooden truss and purlin complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, Az-150 coating of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by the Engineer-in-Charge.

M&L 6mm thick asbestos cement, corrugated or semi- corrugated in roofs,walls etc fixed with L type or J type or cranked hook bolts complete all as specified and as directed by Engr-in -charge.

M&L 6mm thick asbestos cement two piece adjustable plain wing ridge fixed with L type or J type or cranked hook bolts complete all as specified and as directed by Engr-in -charge.

M&L Cleaning and removing all scale and dirt,etc from PVC/RCC tanks and mouths of circulating pipe of exc 250litre and not exceeding 1000 litre capacity & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- Unit rate shall be included to make Small fittings such as elbow, socket, reducer, tee, union etc .

S&F in repair stainless steel fancy type peg set of 05 (05 Nos of hook in each) including fixing with steel screw and PVC rawel plug complete all as specified and as directed by the Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

M & L concrete bed in PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate to drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm dia (internal) pipes complete all as specified and as directed by the Engineer-in-Charge. (Pipes shall be measured & paid separately).

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing surplus excavated material to a distance exc 250m but n.exc 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L providing PCC precast 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating etc and setting CM 1:4 complete with joints to match, complete all as specified and as directed by the Engineer-in-Charge.

Demolition of concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and as directed by the Engr-in-charge.

M & L 40mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in floor, laid in panels and surface finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

S&F glass dividing strips, 38mm wide and 3mm thick, inserted in position to confirm to design of floor complete all as specified and as directed by the Engineer-in-Charge

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, staircases, landings and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by the Engineer-in-Charge.

M & L RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in slab supported on walls, beam and columns in floors, roof, landing, balconies, shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT mild steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work for rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge

M & L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide, for roughed finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash over prepared surfaces of wall, pillar, cornices complete all as specified and as directed by the Engineer-in-Charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white lime wash over prepared surfaces of the walls pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash on ceiling complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white lime wash on ceiling complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of distemper oil emulsion on ceiling complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper over prepared surfaces of the walls pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of plastic emulshion on interor surfaces complete all as specified and as directed by the Engr-in-charge.

Preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the walls pillars, cornices etc.complete all as specified and as directed by the Engineer-in-Charge.

Preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of cement base paint on the walls pillars, cornices etc.complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated wooden surfaces, and applying one coat of synthetic enamel (ordinary tint) on wooden surfaces of any description, not otherwise described, over 10cm width or girth complete all as specified and as directed by Engineer-in charge .

M & L preparing old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding of any type/ size as in CB / Wardrobes or fixed in any position in hardware (if any) etc complete all as specified and as directed by the Engr-in-charge.

S&F 18mm thick lead free PVC celuka ply of both side plain white colour fixed with screws solvent cement / adhesive to make kitchen / bed rooms cabinet sides, top and bottom and shelves inside the cabinets complete all as per manufacturer's specifications/ instructions complete all as specified and as directed by the Engr-in-charge.

S & F continuous (pino) hinges , width of flaps 30mm (when open) mild steel bright finish or electro galvanished complete all as specified and as directed by the Engr-in-charge.

S & F 40mm dia brass polished cupboard knobs,fixed with nut, screw and washer of mild steel, bright finihed complete all as specified and as directed by the Engr-in-charge.

M/s Vridhi Construction Co.

Sawhney Constructions

RONKI RAM AND COMPANY

Sham Sunder Bansal

Shiv Construction Co.

Ashwani Kumar

Durga Enterprises

OJHA ENTERPRISES