DEPOSIT-Construction of Regulator Across Vamanapuram River in the upstream of Kollampuzha Bridge in Thiruvananthapuram District-Construction of Regulator Across Vamanapuram River in the upstream of Kollampuzha Bridge in Thiruvananthapuram District.

Amount

Appendix A- Construction of Regulator

2.3.1.B:Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness In area of thorny jungle -By Manual Means

OD9378/2023-2024:Construction of cofferdam for the construction of RCB with required breadth and height, maintaining the cofferdam during construction and removing after construction etc complete ( contractor should submit the working drawing with necessary details of cofferdam and get approval of Engineer in charge before construction).

OD9379/2023-2024: Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection, cost of fuel, lubrication oil and other stores, including all operation cost etc.

OD9380/2023-2024: 60.2.4 BAILING OUT WATER USING PUMP ABOVE 10HP AND UP TO 20HP - Bailing out water with engine and pump set above 10HP and up to 20HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, including all operation cost etc.

OD9381/2023-2024: Bailing out water using pump above 30 HP and up to 40 HP -Bailing out water with engine and pump set above 30 hp and up to 40hp ,including conveyance to site and erection, cost of fuel ,lubrication oil and other stores, including all operation cost etc. Data as per OD irrigation 60.2.6

12.25.3:Bored cast-in-situ M35 grade R.C.C. Pile Using Batching Plant, Transit Mixer and Concrete Pump excluding Reinforcement complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead upto 1000 m. Pile diameter-1200 mm

OD24038/2023-2024:Boring Providing and installing bored cast insitu reinforced cement concrete piles of M35 grade of specified diameters and length into hard rock, to carry a safe working load not less than specified excluding the cost of steel reinforcement but including the cost of boring with bentonite solution including removal of excluded earth with all lifts and leads-1200mm dia piles

OD9382/2023-2024:Integrity testing of pile using low strain/sonic energy test/sonic eco test method in accordance with IS 14893 including surface prepearation of pile top by removing soil ,mud,dust and chipping lean concrete lumps etc and use of computerised equipment and high skilled trained personal for conducting the test and submission of results all complete a per direction of engineer in charge

12.1.B.2:Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removal of stumps and other deleterious matter, only for dressing of sides and bottom and backfilling with approved material. Ordinary Soil - Depth 3 M to 6 M- Mechanical Means

12.39:Providing and laying of PCC M15 leveling course 100 mm thick below the pile cap

12.8.B.1:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications <br> PCC Grade M20<br>

12.38.C.2:Cement Concrete for Reinforced Concrete in Pile Cap complete as per Drawing and Technical Specification R C C Grade M-30- Using Batching Plant, Transit Mixer, and Concrete Pump

13.5.G.p.2:Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M30 - Height upto 5m - using Batching Plant, Transit Mixer and Concrete Pump

OD9384/2023-2024:Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M30 - With Batching Plant, Transit Mixer and Concrete Pump - Height 5m to 10m

13.5.G.r.2:Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M30 - With Batching Plant, Transit Mixer and Concrete Pump - Height above 10m

OD9386/2023-2024:Providing hot rolled Z steel sheet pile EN 10248 of size 700x420x8.5mm or nearest available size driving down vertically in lines and levels interlocking with adjacent piles with suitable pile driving unit and all accessories including all labour hire charge etc. complete and as per the directions of departmental officers at site (Item to be pre measured)

OD9387/2023-2024:Providing & making Gabion structure with Mechanically Woven Double TwistedHexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause2500, of required size, Mesh Type 10x12(D=100 mm with tolerance of 2%), Zinic+10%Al alloy+PVC coated, Mesh wire diameter 2.7/3.7mm (ID/OD), mechanically edged/selvedged with partitions at every 1m interval and shall have minimum 10 numbersof openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter2.2/3.2mm(ID/OD), supplied @3% by weight of Gabion boxes, filled with boulderswith least dimension of 200 mm, as per drawing, all complete as per directions of Engineer-in-charge

12.22:Providing Steel Liner 10mm thick for Curbs and 6 mm thick for Steining of Wells including Fabricating and Setting out as per Detailed Drawing.

OD9388/2023-2024:Supply, Fitting and PlacingFusion bonded epoxy coated(confirm to IS 13620-1993) HYSD bar or TMT Reinforcement in Foundation complete as per Drawing and Technical Specifications and as per 12.40 of MORTH specifications

OD9389/2023-2024:Supply, Fitting and PlacingFusion bonded epoxy coated(confirm to IS 13620-1993) HYSD bar or TMT Reinforcement in substructure complete as per Drawing and Technical Specifications and as per 13.6 of MORTH specification

OD9391/2023-2024:Sand filling in foundation trenches as per drawing and technical specification using available sand

OD9392/2023-2024:PVC WEEP HOLES- Providing weep holes using 75mm dia. PVC pipes working pressure 4kg /sq.cm including cost of materials, conveyance, labour charges etc. complete.

Appendix B- Bank Protection Work

OD9350/2023-2024:Construction of ring bund for the construction of RCB with required breadth and height, maintaining the cofferdam during construction and removing after construction etc complete ( Contractor should submit the working drawing with necessary details of cofferdam and get approval of Engineer in charge before construction).

OD9351/2023-2024:Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection, cost of fuel, lubrication oil and other stores, including all operation cost etc.

OD9352/2023-2024:Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, including all operation cost etc.

OD9353/2023-2024: 60.2.4 BAILING OUT WATER USING PUMP ABOVE 10HP AND UP TO 20HP - Bailing out water with engine and pump set above 10HP and up to 20HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, including all operation cost etc.

OD9354/2023-2024:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil

OD9355/2023-2024:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

OD9356/2023-2024:Bored cast-in-situ M25 grade R.C.C. Pile excluding Reinforcement complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead upto 1000 m. Using Concrete Mixer - Pile diameter-800 mm as per 55.17.4 MORTH OD

12.38.B.2:Cement Concrete for Reinforced Concrete in Pile Cap complete as per Drawing and Technical Specification R C C Grade M-25 - Using Batching Plant, Transit Mixer and Concrete Pump

13.5.F.P.2:Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M25 - With Batching Plant, Transit Mixer and Concrete Pump - Height upto 5m

13.5.F.q.2:Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M25 - With Batching Plant, Transit Mixer and Concrete Pump - Height 5m to 10m

OD9357/2023-2024:Providing weep holes using PVC/HDPE pf 110mm dia. including all cost and conveyance labour charges etc. complete.

OD24108/2023-2024:Supply, Fitting and PlacingFusion bonded epoxy coated(confirm to IS 13620-1993) HYSD bar or TMT Reinforcement in substructure complete as per Drawing and Technical Specifications and as per 13.6 of MORTH specification

OD24109/2023-2024:Supply, Fitting and PlacingFusion bonded epoxy coated(confirm to IS 13620-1993) HYSD bar or TMT Reinforcement in Foundation complete as per Drawing and Technical Specifications and as per 12.40 of MORTH specifications

OD9358/2023-2024:Supplying at site of work granite stones 20-40dm3 in size (75%30 to 40 dm3 and 25%of 20 to 30 dm3) including stacking at site for premeasurement. Deducting not less than 15% for voids asfixed by the deptl. officers at site.

OD9359/2023-2024:Conveyance of granite stones 20-40dm3 in size from stack at site and dumping in position to lines and levels to form the protection work as per approved design including all incidental charges etc. complete.

OD9360/2023-2024:Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand)

Appendix- C- Kadavu

12.1.B.2:Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removal of stumps and other deleterious matter, only for dressing of sides and bottom and backfilling with approved material. <br> Ordinary Soil - Depth 3 M to 6 M- Mechanical Means<br>

12.8.A.1:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. <br> PCC Grade M15 <br>

12.8.B.1:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications <br> PCC Grade M20<br>

OD24083/2023-2024:Supply, Fitting and PlacingFusion bonded epoxy coated(confirm to IS 13620-1993) HYSD bar or TMT Reinforcement in Foundation complete as per Drawing and Technical Specifications and as per 12.40 of MORTH specifications

Appendix D- Generator cum Watchman Room

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.33.1:Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

13.46.1:Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.48.3:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.2.1:Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge using Anjili/ Jack wood

50.9.15.1:Supplying and fixing 200 mm Aluminium aldrop

50.9.15.3:Providing and fixing iron hooks and eyes : 200mm.

50.9.15.5:Providing and fixing iron hooks and eyes: 100 mm

50.18.7.4.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.8.9.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

9.48.1:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

9.53:Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.97.3:Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.100.2:Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:100 mm

9.103:Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

9.117.1:Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.1:Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

14.29:Providing and fixing M.S. round or squre bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows.

11.38:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

OD9337/2023-2024:Providing and fixing superior quality brand CP Soap Dish Holder concealed fitting arrangements, weighing not less than 106 gms (Make: Jaguar)

OD9338/2023-2024:providing and laying antiskid ceramic floor tiles 300x300x7 mm of 1st quality conforming to IS 15622 of approved make ,shade and pattern laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc .including cost and conveyance of all materials ,labour charges ,lead ,lift etc ,complete as directed by the Engineer in charge at all levels

OD9339/2023-2024:Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

OD9340/2023-2024: Supply and fixing of C.P towel rod 450mm long or nearest available length including<br>cost of materials, labours etc complete

51.19.ST1:Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 1. Below 15 flush capacity

10.5.1:Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

10.6.2:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.7.2:Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

17.3.1:Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.3:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Appendix E- Mechanical Work - E.1 Fabrication ,Supply & amp;amp; erection of MS & SS embedded parts for 6 Nos. of shutters

OD9345/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD9346/2023-2024:Supply of MS round bar including cost of conveyance charges

OD9347/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD9348/2023-2024:Supply of Bolt and Nut up to 300mm Length including cost of conveyance.

85.108:Fabrication , erection and commissioning of Structural Steel Embedded parts in IS2062 Grade and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charge etc complete but exculding cost of materials already supplied

OD9349/2023-2024:Fabrication, supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc, lead and lift, conveyance, incidental and handling etc complete Rate analysis SS Embedded parts 2.6Qtl

APPENDIX E2 - Supply of materials, fabrication, painting , and erection of MS Regulator shutter size 12.7m ( width ) x 5.75m (Height)

OD9372/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD9373/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD9374/2023-2024:Fabrication and supply of Structural steel wheel gate and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

85.112:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350microns over the grit blasted and cleaned surface to class A standard of IS 14177 including cost of all materials , labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc complete as per the direction of departmental officer at site

85.111:Erection of the gates safely in the grooves , assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site

OD9375/2023-2024:Supply and fixing of SS Bolts

OD9376/2023-2024:Supply and stacking of dia 8mm SS-304 chain. including cost of materials, conveyance etc.complete dia 8mm SS-304 chain for Dogging beam

OD9377/2023-2024: Providing rubber flap in between splice plate and skin plate of shutters including cost of rubber and and labour charges, but excluding cost of SS bolts and nuts

APPENDIX E3 - Supplying and fixing of flat type rubber seal at the bottom side , angular type at upstream vertical side and cast steel thrust rollers

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.117:Supplying and fixing in correct position with specified initial interface the Angular type rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.121:Supplying and fixing cast steel thrust roller assembly having 300mm Dia, 90mm tread width, SS(304) shaft and 22315E self aligning spherical roller bearing and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc complete

APPENDIX E4 - Supply of materials, fabrication,painting and erection of hoisting bridge, covers and frames of driving units & rope drum for shutter

OD9394/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD9395/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.103:Supply of MS checquered plates including cost of conveyance charges

OD9396/2023-2024:Supply of GI pipe 32mm dia

OD9397/2023-2024:Supply of MS round bar including cost of conveyance charges

OD9398/2023-2024:Supply of Bolt and Nut up to 300mm Length including cost of conveyance.

85.124:Fabrication and supply of Hoisting bride unit in structural steel confirming to IS2062 Gr including ladder, covers for hoisting unit etc as per approved specifications, drawings and directions of departmental officer at site including cost of labour, machinery, incidental and handling charges for fixing handrails and allied works etc complete but excluding material already supplied and weight of pipes for hand rails etc

OD9399/2023-2024: Painting all the exposed surfaces 2 coats of enamel paint over 1 coat of zinchromate primer as per IS 1477:1994 over the grit blasted and cleaned surface to class A standard of IS 14177 including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc complete as per the direction of departmental officer at site.

85.136:Erection of the hoisting bridge unit including handrails , ladder and platform etc. in correct alignment and anchoring it ; setting and aligning the covers of the hoisting unit etc complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

APPENDIX E5- Supplying, stacking, erecting and trial run of rope drum hoisting Unit PRICE EST NO:2018/9159 printed

85.128:Providing Line shaft ,material : MS rolled/ forged steel

OD9341/2023-2024:Supplying and stacking of 40 Tonne capacity rope drum hoisting unit having 13.5 m lift at a hoisting speed of about 0.33 m/min(+/-10%) through pulley arrangements with 4 numbers of falls on either side with 24mm tested galvanized wire rope 6/36 construction, fibre core having breaking capacity 34251Kg and driven by TEFC squirrel cage induction motor hoist duty type having capacity not less than 7.5HP and driven through self locking worm reducer and open gear reduction unit including 2 nos. of plummer blocks with bearings for line shaft supported at proper intervals and including cost of electro magnetic thruster brake assembly manual operating systems, electrical accessories like DOL starters, limit switch, main switches and other safety equipments as per drawings specifications and statutory requirements etc complete

OD9342/2023-2024:Supplying and stacking of 20 Tonne capacity rope drum hoisting unit having13.5 m lift at a hoisting speed of about 0.50 m/min(+/-10%) through pulley arrangements with 4 numbers of falls on either side with 18mm tested ungalvanized wire rope 6/36 construction, fibre core having breaking capacity 19266Kg and driven by TEFC squirrel cage induction motor hoist duty type having capacity not less than 5HP and driven through self locking worm reducer and open gear reduction unit excluding the cost of line shaft but including 2 nos. of plummer blocks for line shaft with bearings supported at proper intervals and including cost of electro magnetic thruster brake assembly manual operating systems, electrical accessories like DOL starters, limit switch, main switches and other safety equipments as per drawings specifications and statutory requirements etc complete but excluding cost of wire rope Rate analysis for 20T capacity Rope Drum Hoisting unit

85.125:Conveying and erecting in position the already supplied rope drum hoisting units ( 15T/20T/25T/30T) capacity on the hoisting bridge and correcting the alignment as far as possible manually as per the direction of departmental officer at site including cost of all labour, machinery, lead and lift and all incidental and conveyance charge etc complete

85.135:Conveying and Fixing wire rope already supplied to the new gates and Hoisting unit safely and conducting Trial Run

OD9343/2023-2024:Providing Dial guage assembly with with Dial, 1 5/8 feet worm reducer, chain & Sprockets, Frame and other accessories

OD9344/2023-2024:Supplying Wire rope: 18mm dia, 6/36 Construction, Right hand lay, Ungalvanized, main fibrecore, UTS 180 KG/MM2 having breaking load capacity of 336 KN(19266kg), Conforming to TO IS 2266 -1989

Appendix F- Electrification works

90.14.1.2:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.2:Supply and providing 3mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.3:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardSupply and providing 'U' section PVC beeding in the panel board

90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7:Supply and providing copper earth bus in the panel board

90.14.10.6:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.125A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.10.7:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.160A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.1:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.50.1:Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

2.2.3:Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.160 Amp, 16KA,TPMCCB

2.10.1:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.2:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

OD9361/2023-2024:Supplying, installing, testing and commissioning of 3 phase digital multifunction meter in the existing panel board

OD9362/2023-2024:Supply and installation of LED indicator (R,Y,B) in the existing panel board and giving connection

90.12.7.29:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp

90.12.7.39:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 6 sq mm with factory made clamp

90.12.7.40:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

9.1.22:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.32:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

4.1.1:Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width X 50 mm depth X 1.6 mm thickness

4.2.1:Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width X 50 mm depth X 1.6 mm thickness

OD9363/2023-2024:Supply, erection, testing and commissioning of 40 kVA DG set with standard accessories coupled to alternator rated 40 kVA/32KW, 3 phase, 4 wire, 0.8 PF (lag), 415 V mounted on a channel iron base frame with foot mounting AVM pads, Fuel tank (In Built), Charged battery with leads, Silencer along with exhaust stack, acoustic enclosure and standard control panel.

OD9364/2023-2024:Providing & fixing Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with control discharge mechanism confirming to IS: 15683.

OD9365/2023-2024:Supply of 450mm sweep wall fan on surface including mouting and providing all accessories required for complete installation, testing, commisioning etc as required complete (Havells Airboll Hi-Speed or equivalent)

OD9366/2023-2024:Proving and fixing fire buckets with stand

OD9367/2023-2024: Design, fabrication & supply of cubicle type dust and vermin proof, made out of 16SWG /1.6 mm thick CRCA sheet duely rust inhibited, zinc passivated, phosphate and powder coated with approved color, hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets removable gland plates made out of 2mm thick sheet steel as per specifications and interconnected with suitable AL. Busbar. Rate shall be inclusive of ncessary control wirings, necessary relays as required and as instructed by engineer in charge. Panel should have lockable & sealable chmabers. Metering Panel (Outdoor Type with Canopy) Incomer : Fuse Base+NL+HRC Fuse 125A 415V, 25kA best conductivity Al extensible TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. RYB phase indicating LED lamps with control fuses and switches - 1set. LT TOD Meter with necessary CTs and control wirings Earth leakage relay Lockable & selable CT Chamber Outgoings 125A FP 25kA Thermal Magnetic MCCB Supply, Installation, Testing and Commissioning

OD9368/2023-2024:Supply and providing following sizes of 'B' Class MS pipe with specials and flanged coupling in each full length of pipe, as additional exhaust piping, fixing the same firmly to the builing /structure using necessary supports, such angle iron, MS clamp etc., painting the pipe and accessories with synthetic enamel paint over a coat of zinc chromate primer etc. as required.100 mm dia or nearest size 'B' Class MS pipe

90.3.19.3:Supply conveyance, installation, testing and commissioning the light fittings of following types made from CRCA sheet 0.5mm thickness with all accessories and lamps directly on wall and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required1200 mm 1X20W LED Lamp with box type fixture

OD9369/2023-2024:Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.1200mm sweep -5star rated ceiling fan complete with 300mm down rod , canopies, shackles and blades working on 230V/240V single phase A/C.

90.11.1.11:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

1.25:Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

5.1:Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

OD9370/2023-2024:Providing and fixing 25x6 GI Strip

OD9371/2023-2024:Providing and fixing 25x3 GI Strip

Appendix G- External lighting

OD9403/2023-2024:Design, fabrication & supply of cubicle type dust and vermin proof, made out of 16SWG /1.6 mm thick CRCA sheet duely rust inhibited, zinc passivated, phosphate and powder coated with approved color, hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets removable gland plates made out of 2mm thick sheet steel as per specifications and interconnected with suitable AL. Busbar. Rate shall be inclusive of ncessary control wirings, necessary relays as required and as instructed by engineer in charge. Panel should have lockable & sealable chmabers. External Lighting Panel (Outdoor Type with Canopy) Incomer - 40A 300mA FP RCBO- 1No. 40A 433V, 16kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoing: 16A TP MCB - 4 nos. 12A TP Contactor - 4 nos. Astronomical time switch for automatic switching On & Off of street lights at sun set & sun rise or twilight (Auto ON, Auto Off, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required. - 4 nos. Supply, Installation, Testing and Commissioning

OD9404/2023-2024:Supply and laying 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date - 3Cx 06 Sq.mm Al Cable

OD9405/2023-2024:Supply, installation, testing and commissioning of 7 Mtr Hot Dip Galvanized Street Light Octagonal Pole with Foundation Type Base Plate & Foundation Bolts Foundation Bolts with double type arm bracket 1500 mm long made of 60 mm dia pipe suitable for LED street light fitting. The Octagonal Poles shall be in single section. There shall not be any circumferential weld joint. The poles shall be hot dip galvanized as per relevant Indian standards with average coating thickness of minimum 65 micron. The Octagonal Poles shall be suitable for bolting on a foundation with a set of four foundation bolts for greater rigidity. The pole shall have necessary door opening, 6A SP MCB, Internal wiring etc as required

OD9406/2023-2024:Supply, installation, testing & commissioning of street Light LED luminaire with Lamp for mounting on the existing road lighting pole and all accessories complete as required - 75 watt LED luminaires with lamp

OD9407/2023-2024:Supply, installation, testing and commissioning of 7 Mtr Hot Dip Galvanized Street Light Octagonal Pole with Foundation Type Base Plate & Foundation Bolts Foundation Bolts with single type arm bracket 1500 mm long made of 60 mm dia pipe suitable for LED street light fitting. The Octagonal Poles shall be in single section. There shall not be any circumferential weld joint. The poles shall be hot dip galvanized as per relevant Indian standards with average coating thickness of minimum 65 micron. The Octagonal Poles shall be suitable for bolting on a foundation with a set of four foundation bolts for greater rigidity. The pole shall have necessary door opening, 6A SP MCB, Internal wiring etc as required

5.16:Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

9.1.7:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 10 sq. mm (22mm)

POONAM GRAH NIRMAN PVT LTD

Bidder Name

POONAM GRAH NIRMAN PVT LTD

k k constructions