REPAIR/ REPLACEMENT OF DOOR, WINDOW, FLOORING, TILING, ROOF TRATMENT AND MISC B/R WORKSAT NARENDER NAGAR UNDER AGE (I) RAIWALA

Amount

M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for Cement concrete ( reinforced) including removal of debris etc to a distance out side MoD land complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed.

M&L for formwork for rough finish to soffits of suspended slabs such as roof slabs, floor slabs, landing slab and similar work, not exceeding 200mm thick complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

Description same all as item No. 08 above but except brick complete all as specified and directed. Note:- Old retreived serviceable bricks shall be used under this item.

M&L for brick work with old size half brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed.

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed.

M&L for 15mm thick plastering on fair faces of brick wall in CM (1:6) surface finished even and fair complete all as specified and directed.

M&L for preparing old decorated plastered surfaces of wall by complete removal and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. Note :- The old plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M&L for preparation of newly plastered surface of interior wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of interior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge. Note for item No 17 & 18 :- (i) The old/ New surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour and T&P required for preparation of surface are demand to be included in the rates quoted. (ii) The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii) All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv) after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v) Before commencing the work, contractor will got the written approval from GE/ AGE (I) for the make and colour / shade (tint). (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor.

S&F in repair 5mm thick beveled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed.

S&F in repair of stainless steel peg set of 3 Nos fixed to wooden plank complete all as specified and directed.

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:-

Area not exc 1.5 sqm each

Area exc 1.5 sqm but not exc 4 sqm each

Taking down shutters of any description, of following size complete all as specified and directed:-

Area not exc 1.0 sqm each

Area exc 1.0 sqm but not exc 2.0 sqm each

Taking down and refixing shutters in the same opening of any description including easing and adjusting, of following size complete all as specified and directed:-

Area not exc 1.0 sqm each

Area exc 1.0 sqm but not exc 2.0 sqm each

M&L for MS fastner of FI 50x5mm size and length 200 to 250mm for fixing wooden door/ window frame and like in postion complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

65mm x100mm size

65mm x 125mm size

S&F flush shutters, ISI mark, solid core construction with block board core and ply wood face panels, commercial type on both sides for following thickness complete all as specified and directed:-

35mm thick

M&L for 30mm thick factory made solid WPC (wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texteure, including stainless steel wire mesh shall be fixed with 15 x15 mm square tube in side rails with screwing 8 x 28 heat metal zink coated screw can be remove or fix again after changing of wire mesh, when needed. The density of the shall be as per manufacture instruction compete all as specified and directed.

M&L for 30mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and directed. Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.

M&L for factory made 35mm thick 100% solid WPC window glazed shutter and Gauzed (wire mesh) shutter 95 mm x35mm thick. Made from WPC material with density not less than 800 kg/cum. All four corner are fusion welded & screwed with 8 x 50mm self-screws for additional strength. After joining all 4 corner clear space to be paneled with 5mm thick glass / S S mosquito mesh after glazing of inside of shutter 10 x 12mm pvc “L” shape bead to be nailed or sticked with shutter. Provided 2 Nos SS hinges of 100 mm, 1 Nos aluminium handle of 125 mm , 2 Nosaluminium tower bolt of 125mm and 01 peg stay for each shutter (Glazed and Gauzed) incl factory made 100 % solid WPC window frame 125 mm x 65 mm double rebated frame & mullion 125 x 80mm. made from WPC (Single extruded process) material comparising of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (Wood powder/ rice husk/wheat husk) and nontoxic additives fabricated with meter joints after applying PVC solvent cement & screwed with fully body treated star headed screws having minimum frame desity not less than 800 kg /cum, having good screw holding capacity (screw withdrawal strength of (min 990N). Minimum compressive strength of 58 N/mm2. Modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / mosquito proof & fire retardant & fixed in position with fasteners / hold fast of required size. Window shall be provided with MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat including painting with countersunk holes at both vertical ends. Gap between the bars should not be more than 125mm. All as per specification drawing as directed by Engr-in-charge. Note - (i) Glazed and Gauzed shutter both are deemed in this quoted rate (ii) Glass pane, wire mesh and grill are deemed in this quoted rate

M&L for two coats of synthetic enamel paint over a coat of pink primer including preparation of new wood or wooden base surface over 10cm width or grith complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

S&F stainless steel barrel tower bolts of extruded section (ISI Markd) of following size complete all as directed and specified:-

300 mm long

200 mm long

S&F in repair stainless steel barrel tower bolts of extruded section (ISI Markd) of following size complete all as directed and specified:-

300 mm long

S&F stainless steel handles fabricated type, of following size complete all as directed and specified:-

200 mm long

125 mm long

S&F in repair stainless steel handles fabricated type, of following size complete all as directed and specified:-

200 mm long

S&F stainless steel sliding door bolt with hasp & Staple, bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of following size complete all as specified and directed:-

300mm long

S&F in repair stainless steel sliding door bolt with hasp & Staple, bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of following size complete all as specified and directed:-

300mm long

S&F stainless steel, non magnetic butt hinge (ISI Marked) and fixed of following size complete all as specified and directed:-

100 mm long

S&F stainless steel continuous (piano) hinges, bright finish or electrogalvanised, width of flap (when open) 40mm complete all as specified and directed.

S&F auto closing hinges 35 mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet & ward robe shutters complete all as specified and directed.

S&F in repair floor door stopper (ISI Marked) of aluminium alloy body and tongue anodised, with hard drawn steel spring, fixed in floor of following size complete all as specified and directed :-

150mm long (overall length of cover plate)

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or wire staples complete all as specified and as directed.

S&F stack clamps out of 40mm x 3 mm flat iron including bolts and nuts and securing ends of stays to wall or roof for following bore of pipe complete all as specified and directed :-

100mm bore pipe

75mm bore pipe

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F rolled mild steel section for structural steel work as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding crane, fixed with angle cleats or other connecting plates/ bolts, conforming to Fe-290(Gde-E-165) complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

S&F mild steel as in hand rail, wind tie including all necessary drilling, bolting or rivetting etc and similar work confirming to Fe-290-Gde E165 complete all as specified and as directed.

M&L for 60mm thick coloured rubber moulded glossy finish machine pressed precast concrete interlocking paver block, M-35 Grade with pre-polished, coloured/ laquar finish any shape and size, as approved confirming to IS 15658-2006 with and including over 40mm thick stone dust/ sand cushining complete all as specified and directed.

Removal of existing roof treatment i.e APP membrane and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material complete all as specified and directed. Note for all Item of roof treatment :- The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding, safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these items .

M&L for PCC (1:2:4) type B-0, using 12.5 mm graded stone agg mixed with SBR Latex liquid polymer as water proofing compound (mixed as per manufacture instructions) over and including one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete/ mortar to old surface as per manufacturer direction and finishing the surface even and smooth without using extra cement as in roof padding / sunken floor to receive water proof treatment complete all as specified and directed. Note :- The cost of SBR latex deemed included in quoted rates.

M&L for water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer’s instructions with following course of description below :- (a) Applying a priming coat of bituminious primer @ 0.30 Kg /Sqm, till the surface is properly impregnated. (b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6Kg/ Sqm and minimum 3mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms/sqm) centre core, laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75 mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch ) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer (c) Apply two coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance

Note : (i) The work of water proofing treatment shall be got executed through authorised applicator of the manufacturer only and 10 year company back warranty to be submitted by contractor. (ii) The work is required to be carried out at non-accessible roof slab for double storeyed. The contractor shall make arrangement of scaffolding, safety and security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items.

Dismantling of asbestos cement ( corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden/ PVC/ aluminium beading, in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden or aluminium or PVC beads in square in each pane of following size complete all as specified and as directed :-

Not exc 0.5 sqm in each pane

S&F second class hard wood (sal) plain, fillets, square, rectangular or triangular in section clean sawn, secured with nails of following sectional area complete as specified and as directed:-

Sectional area exc 3 sq cm but not exc 6 sq cm

Dismantling of wall and ceiling boards ( fibre, pulp insulation etc.) or insulation boards/ slabs/ blankets of any thickness, including cover fillets complete all as specified and directed.

S&F solid PVC wall panelling consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site with and including 5 mm thick PVC sheet fillet of width 35 mm for wall panelling with suitable distance and frame vertically and horizontally as per specification and drawing in any position with screws complete and as directed

Dismantling of boardind of any deescription and fixed in any position with nails complete all as specified and directed.

S&F 18mm thick PVC/ WPC solid, both side prelam celluca plyboard for cabinet boxes & shutter, cup boards, drawer, etc with shelf and shutter incl lipping to edges of exposed surface including provn of fixing arrangement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises from MoD land complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for coloured vitrified tiles, double charged, of any design and pattern, 9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption between 0.08% to 3%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects Complete all as specified and directed :- Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

Area of each tile not exc 0.36 sqm.

M&L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick, of following size, as in floor etc with and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 3% to 6%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1000 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed :- Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE (I).

Area of each tile exc 0.06 Sqm but not exc 0.11 Sqm.

Area of each tile exc 0.18 Sqm but not exc 0.38 Sqm.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mm thick, as in dado etc including 10mm thick rendering in CM (1:3), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

S&F in repairs for stainless steel non magnetic curtain rod of 25mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE both side of each rod complete all as specified and directed. Note: - Measurement will be taken between end point of knobs.

S&F aluminium door seal upto 1200mm long on bottom of door complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic seat and cover, white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (Pedestal pattern) incl close seat cover, hinges,fixing accessories and accessories set and cistern with cistern fitting complete, flush pipe incl all joints complete all as specified and directed. Make – Jaquar Cat No-ECS-WHT-851S220NPP or equivalent model of make as specified in appendix.

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F in repair chromium plated health fauset, telephonic type with CP flexible arms and hooks of approved make suitable to fix to 15mm bore CP angle valve complete all as specified and directed.

S&F in repair toilet paper holder of brass, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repair vitreous china half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F brass CP urinal spreader fixing with 15 mmdia pipe complete and all as specified and directed.

S&F in repair Wash basins (Padestal pattern) 550x400mm vitreous china (flat back type) any size incl cutting for and pinning in end of brackets for erecting stand but exclusive of fixing of supply and waste pipe but including waste fitting complete all as specified and directed.

S&F in repair 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstanhead screwed for 15mm dia pipe fixed in repair. complete all as specified and directed.

S&F in repair 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm bore pillar taps of standard PTMT any colour ahigh pressure screwed for iron pipe and fixed in repair (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified and directed.

Disconnecting and dismantling of water storage tank and removing from the site of following capacity of tank complete all as specified and as directed:-

Capacity exc 250 Ltr but not exc 500 Ltr

Capacity exc 500 Ltr but not exc 1000 Ltr

S&F rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of following capacity of tank complete all as specified and as directed:-

Capacity 500 Ltrs

Capacity 1000 Ltrs

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixed of following size complete all as specified and as directed :-

20mm bore ( minimum weight 210gms)

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) bends with access door any radius of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) junction single, (single T) equal or unequal of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) vent cowl of following size complete all as specified and as directed :-

75 mm bore

S&F PVC (SWR) multi floor trap, out let dia 75mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) floor trap, out let dia 75mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) P trap, out let dia 110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) reducers of size 110 mm x75 mm complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required of following size complete all as specified & directed :-

100mm bore

S&F in repair chromium plated brass tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair chromium plated brass tubular towel ring fixed with CP screws with wall complete all as specified and directed.

S&F in repair brass chromium plated towel rack of size 600 mm fixed with and including CP brass screws and wooden/plastic cleats, complete all as specified and directed.

S&F in repair Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long.complete all as specified and directed.

S&F in repair sheet glass cornor self of 3 tier assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F in repairs 15mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions complete all as specified and directed. Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repair 15mm bore stop angle valve, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S&F in repair 15 mm bore bib taps, chromium plated, fancy type, long body, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S&F in repair 15 mm bore bib tap of standard PTMT (min wt 90 gm), any colour, high pressure, screwed for iron pipe and fixed complete all as specified and directed .

S&F in repair wall mixer with L bend for over head shower incl shower rose of size 125 mm and shower arm chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed.

S&F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to 15mm GI pipe or union complete all as specified and directed.

S&F in repair PVC connection 15 mm size with PTMT nut of following length complete all as specified and directed :-

S&F in repair 127mm dia round grating chromium plated complete all as specified and directed.

S&F in repair stainless steel jet spray suitable for europian western commode (EWC) including 1.5m length braided tube with PTMT nut and washer complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 15mm thick screed bed in cement mortar (1:3) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

Description same all as per item No 112 above but, as in skirting/ dado (10-12mm thick Kota stone) over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 18-20mm thick pre polished Udaipur green stone (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx 330mmx160mm complete all as specified and directed.

S&F in repair stainless steel sink with out draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 495mmx420mm with bowl size 410mmx 330mmx160mm complete all as specified and directed.

S&F in repair aluminium body door closer hydraulically regulated, designation No -3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight 61 to 80 Kg (ISI marked) complete all as specified and as directed.

M&L for heavy duty coloured tiles (dark shade) with chequered, plain or recess finish at top of size 300x300x 8 to 10mm thick as in floor/ path/ paving etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-

15mm bore

20mm bore

Refixing old galvanised steel water tubing, with all new fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-

20mm bore

M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:3) to match with existing surface for following girth complete all as specified and as directed :-

Cutting not exc 10cm girth.

S&F in repair low density polythene pipe (LDPE) of pressure rating 6 Kgf / sqcm fixed to wall or laid in floor etc including fittings of following size complete all as specified and as directed :-

32 mm bore

S&F in repair stainless steel kitchen plate rack 0.80mm thick sheet of over all size 31" x 30" x 10" fixed with steel screws and steel rawal plugs complete all as specified and directed. Note :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

AMAR NATH SHARMA