Construction work of Sub District Hospital Khanpur under District Haridwar

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth ,consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m .

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand:08graded brick aggregated 40mm .nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement :3 coarsesand : 6graded stoneaggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH COL SUPER STRUCTURE

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH Roof Beam

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH Slab

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH Staircase

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars.

230 th Brick work with brick of class designation 75 in foundation & plinth in cement mortar 1:6

Brick work with F.P.S bricks of class 75 in super structure above structure above plinth level up to floor five level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand )

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S.bars at every third course of half brick masonry (with F.P.S.bricks).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade Casement cum fixed panel window having one single casement panel & one fixed panel with S.S 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (Zamak) powder coated handles.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing & fixing of wire mesh (mosquito jalli) with labour & material comlete With 12 mm mild steel U beading.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 75 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete100x10 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms.

Providing and fixing M.S. Tubular frames for doors and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge(Door handle, lock and stopper etc.to be paid separately).

P/F 1st quality ceramic glazed wall tiles conforming to IS : 15622 of approved make in colours , shades except burgandy , bottel green , black of any sizes as approved by Engineer -in -Charge in skirting , risers of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of all colour black, cherry/ruby red Area of slab above 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conformingto IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) Medium shade pigment using 50% white cement, 50% ordinary cement

12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable sq.m shade with ordinary paint of approved brand and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced ----------------------------------------------------all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part | and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The systemshall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning /centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or terioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of 100 mm gap

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 16 sq. mm + 1 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.(20) 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.(40)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm (T.V+Telephone+Network)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100 mmX75 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125 mmX75 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200 mmX75 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125 mmX125 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 12 Module (200 mmX150 mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 4 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 8 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Supplying and flxing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and flxing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and flxing brass batten/angle holder including connection etc. as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 3 run of cable

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator) 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supplying and fixing TP sheet steel encosure on surface/ recess along with 16/25/32 amps, 415 volts, "C" curve, TP, MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit,or cutting the wall and making good the same in case of receeesed conduit as required. 20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit,or cutting the wall and making good the same in case of receeesed conduit as required. 32 mm

Providing and fixing circular / hexagonal M.S sheet ceiling fan box with clamp of internal dia 140 mm,73 mm height, 3 mm thick rim, top and bottom lid of 1.5 mm M.S sheet. Lids shall be screwed into M.S box by means of 3 mm round headed screws, clamps shall be made of 12 mm dia M.S bar bent to shape as per standard drawing with over all length as 80 cm.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Above 4.5 metre and upto 6.5 metre

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and laying of following size DWD HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. confirming to IS 14930, Part II Complete with fitting and cutting, jointing etc.. Direct in ground (75cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90mm & ID-76mm nominal)

Supplying and laying of following size DWD HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. confirming to IS 14930, Part II Complete with fitting and cutting, jointing etc.. Direct in ground (75cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required Size 600x450x200 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 MM

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 MM

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Single tee with door 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Single tee with door 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Single tee without door 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Single tee without door 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Bend 87.5° 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Bend 87.5° 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler Shoe (Plain) 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 75 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 110 mm

Providing and fixing 600 x 455 mm. bevelled edge mirror of Saint Gobin or Modi float glass complete with 6 mm. thick hard board ground fix to wooden cleats with CP brass screws and washers etc. complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe ith clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints omplete as per direction of Engineer in Charge Internal work - Exposed on wall 15mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe ith clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints omplete as per direction of Engineer in Charge Internal work - Exposed on wall 25 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe ith clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints omplete as per direction of Engineer in Charge Internal work - Exposed on wall 50 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats 25 mm dia. nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing brass bib cock of approved quality :

Providing & Fixing C.P. brass Long boddy bib cock

Providing and fixing PTMT pillar cock of approved quality and colour

Providing & Fixing C.P. brass stop(conceald)

Providing & Fixing C.P. brass angle valve

Providing & fixing c.p. soap dish parryware make

Providing & fixing Over Head Shower parryware make

Provding & Fixing C.P Towel rail parryware make

Provisiding & Fixing C.P Paper Holder parryware Make

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 75 mm nominal inner dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm nominal bore

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line : for sanitary building

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Cartage of material by mannual labour inculding loading ,unloading & stacking up to 50m

Providing units of reinforced cement concrte 1:1.5:3(1cement :1.5 coarse sand:3graded stone aggregate 20mm.nomnal size) of strength not less than M-150 in lintels and band over door and windows excluding supply of reinforcement and its bending including

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing & fixing of R.C.C manhole covering Septic tank

Providing & fixing of foot rest in tank

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. For 50 kWP

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate I retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: 5.33A Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate I retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: 5.33A Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M30 grade with minimum cement content of 350 kg /cum

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Add for using extra cement in the items of design mix over and above the specified cement content therein

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws Second class teak wood

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood liping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately)

Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement basedhigh polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Udaipur green marble

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For third floor )

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For forth floor )

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For mumty & machine room & perapet wall )

Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, thetop most layer shall be finished with brick tiles of class designation10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixedwith 2% integral water proofing compound by weight of cement overa 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) andfinished neat (item of laying brick tiles shall be paid for separately).

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (40mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal inner dia Pipes

Earth work in excavation by mechanical means ( hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sq.m on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed. All kinds of soil.

Providing and laying in cement concrte 1:4:8(1cement :4fine sand:08graded brick aggregated 40mm .nominal size.) and curing complete excluding cost of form work in foundation and floors.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

40 mm. thick cement concrete flooring 1 :2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. nominal size ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. For 20 kWP

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered 1620 lpm at 56 m Head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required Single headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. onnections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Earth work in excavation in trenches for foundation and for pipes cables etc. in ordinary soil including fitup to 1.5m and dressing of sides and ramming bottoms and disposal of surplus excavated earth as directed by the engineer with in a lead of 50m

Filing available excavated earth in trenches ,plinth,sides of foundation tec.in layers not exceeding 20cm in the depth ,consolidation each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m

Providing and laying in cement concrte 1:4:8(1cement :4fine sand:08graded brick aggregated 40mm .nominal size.) and curing complete excluding cost of form work in foundation and floors.

Providing units of reinforced cement concrte 1:1.5:3(1cement :1.5 coarse sand:3graded stone aggregate 20mm.nomnal size) of strength not less than M-200 in lintels and band over door and windows excluding supply of reinforcement and its bending including

Wall,Columns ,Pillar Post & Struts

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH

COL SUPER STRUCTURE

COL SUPER STRUCTURE Beam

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete TMT

Brick/Fly Ash Brick work with brick of class designation 75 in foundation & plinth in cement mortor 1:6 .

15mm thick plaster on the plain in side of mix 1:6 mortor

Apex both side of wall including cost of all labour ,materials ,T&P etc.,required for proper completing of work

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B Fixing with adjustable

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:(profile c)Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Float glass panes of thickness 4 mm Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with

P/L Ceramic glazed floor tiles 300 x 300 mm of 1st quality conforming to I.S : 15622 of approved make in colours such as White , Ivory , Grey Fume, Red Brown laid on 20 mm thick cement mortar 1:4 including pointing the joints with white cement and matching pigment etc . complete.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.(20) 2 Pair

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100 mmX75 mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125 mmX75 mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 4 Module

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and flxing brass batten/angle holder including connection etc. as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of cable

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required..

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 6 mm thick copper base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (40mm)

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre (full flush) capacity-white

Providing and fixing G.I. inlet connection for flush pipeconnecting with W.C. pan.Concealed work including cutting chases and making good the wall

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm.

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm (70mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm (50mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 4 X 35 sq. mm (32mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 4 X 25 sq. mm (28mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm)

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3 X 10 sq. mm (22mm)

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 150 mm dia

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 250 mm dia

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 95 sq. mm and upto 185 sq. mm (clamped with25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Supplying and making outdoor cable end termination with heatshrinkable jointing kit complete with all accessories includinglugs suitable for following size of 3 core, XLPE aluminiumconductor cable of 11 KV grade as required : 240 sq. mm

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Upto 3 m depth

Water Bound Macadam Sub-base/base WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 404.

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work.(Based on PWD specifications)

Cement Concrete (PCC M-30) Pavement:- Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in pproved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in ontinuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications.

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete 300 mm sweep 900 rpm

Supply of type fluorescent tube light fitting suitable for 1*18w fluorescent tube complete including tubes etc. on surface complete in all respects. philips 18 w

Supply of SYSKA Self Ballasted LED Lamps for General Lighting Service 12 Watts 4 Star complete including tubes etc. on surface complete in all respects. (Rate taken from GeM)

Supply of surya Cool Day Light PVC Square LED surface ceiling Light complete including tubes etc. on surface complete in all respects.

Supply of Square LED surface ceiling Light Flat panel which provides soft-light and glare free symmetrical illumination LEDs 36 W LED as approved by Engineer in charge complete in all respect.

1 x 20 watt Surface mounting type LED light fixture complete with all accessories as required.

1 x 11 watt surface mounting type LED Bulk Head light fixture complete with all accessories as required.

1 x 80 watt LED Flood light fixture complete with all accessories as required.

Supply of following sizes of ceiling fan complete with double ball bearing. motor, blades, downrod, canopy, capacitor, regulator etc. suitable for operation on 230 volts 50 Hz A.C. supply complete as required. Size 1200mm.(Speed Star)

Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.

Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, Installation, Testing & Commissioning of 42 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of Pure IP at core server Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility , 55 IP users License ,01 Nos. IP Operator Console, 100 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, TEC should be with GR Number, - Should Support Redundant server in active-Active mode.

Supply, Installation, Testing & Commissioning of Type 1 IP Phone 1 VoIP account , Full duplex speaker phone, IPV6, 2xLAN, PoE .

Supply, Installation, Testing & Commissioning of Type 2 IP Phone with 2 Voip accounts, 2 Lines , HD Voice,Graphic LCD display with backligh.

Supply, Installation, Testing & Commissioning of Core Switch 24 Port POE+ Access Switches with switching capacity of 240 Gbps, forwarding performance 190 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4 x 10G SFP+ uplink ports, should have support for 9 switch Stacking with stacking cable with bandwidth of minimum 120 Gbps. Should support min 2GB internal DRAM, 2GB internal Flash memory, 32K MAC address, 4k Multicast Routes, Should have static Routing from day 1 and upgradable to support OSPF and VRRP with 1 year support.

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with 2 x 10G SFP+ uplink ports. Should support for Stacking/VC with stacking cable with stacking bandwidth of maximum 40 Gbps as and when required. Should support min 2GB internal DRAM, 2GB internal Flash memory, 16K MAC address. Should have Static Routing , Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), Domain Name System (DNS) and IPv6 features from day 1 and should support OSPF, VRRP, OSPFv3 and PIM.

Providing, fixing & Testing of M.S. Pipe”B” Class including fitting like Tess. Elbows, Reducer Socket, Including M.S. Clamps Red paint over a cost of Primer completion all respect. (Make-Jindal) 150 mm

Providing, fixing & Testing of M.S. Pipe”B” Class including fitting like Tess. Elbows, Reducer Socket, Including M.S. Clamps Red paint over a cost of Primer completion all respect. (Make-Jindal) 100mm

Providing, fixing & Testing of M.S. Pipe”B” Class including fitting like Tess. Elbows, Reducer Socket, Including M.S. Clamps Red paint over a cost of Primer completion all respect. (Make-Jindal) 80 mm

Providing, fixing & Testing of M.S. Pipe”B” Class including fitting like Tess. Elbows, Reducer Socket, Including M.S. Clamps Red paint over a cost of Primer completion all respect. (Make-Jindal) Pipe coating 2mm 100mm (as per required)

Providing, fixing & Testing of Single headed Landing valve. C I Body as per 15: Specification with Instantaneous Coupling SS with black Cap complete in all respect. (Make-Elitech/New Ace/Spago)

Providing, fixing & Testing of Collecting head 63mm dia instantaneous type fire Brigade Connection in let two ways

Providing, fixing & Testing of suction strainer CI Body 150mm (Make-Kartar)

Providing, fixing & Testing of suction strainer CI Body 80mm (Make-Kartar)

Providing, fixing & Testing of caste iron butterfly 150mm (Make-Castle/Kartar)

Providing, fixing & Testing of caste iron butterfly 100mm (Make-Castle/Kartar)

Providing, fixing & Testing of caste iron butterfly 80mm (Make-Castle/Kartar)

Providing,Fixing & Testing of Bal Valve 25mm

Providing, fixing & Testing of Air Release Valve 25mm (Make-Kartar/sent)

Providing, fixing & Testing of pressure Type gauge 10 Kg./Per cm2 (Make-H-Guru)

Providing, fixing & Testing of Pressure Switch (Make-Danfoss)

Providing, fixing & Testing of swinging type first aid Fire HoseReel 30Mtrs. Long 19mm dia Rubber and PVC shutoff Nozzle Complete in all respect. (Make-Elitech/SpagoNew Ace)

Providing, fixing & Testing Of 63mm dia 15 Met Long Canvas RRL Hose Pipe with SS male and female Couplings. Complete in all respect. (Make-Elitech/Spago/Spago)

Providing, fixing & Testing of short Size SS Branch pipe Nozzle 16MMdia. (Make-Elitech/New Ace/Spago)

Providing, fixing & Testing of Fire Hose Cabinet Fabricated. From M.S. Sheet 18 gauge with double Front glazed flanged shutter with locking arrangement stove Enameled Fire red finished. (Make-Elitech/New Ace)

Providing, fixing & Testing of NRV Single Plate 100mm (Make- Castle/Kartar)

Providing, fixing & Testing of NRV Single Plate 80mm (Make- Castle/Kartar)

Providing, fixing & Testing of Fabrication Works angle (As per required)

Providing,fixing & testing of Main Motor pump – LPM-------2280 RPM-------2900 Head------56 M HP------50 (Make-Kirloskar)

Providing,fixing & testing of Jockey Motor pump LPM---------180 RPM----------2900 Head----------56 M HP--------------7.5 (Make-Kirloskar)

Providing,fixing & testing of Diesel Motor pump LPM-------2280 Head-------56 M

Electric Panel – Providing, fixing & Testing of Main Motor------------ Jockey Motor----------- Diesel Motor--------- (Make-Fabricate)

Cable 25 mm04core (Copper)

Cable 10mm034core(Al)

Cable 2,5mm5core (cop)

Provinding & Fixing of Foot Valve 80mm

Provinding & Fixing of Foot Valve 100mm

Sprinkler System

Supplying, installation & testing of Fire Alarm main Panel 08 Zone. (Make-Agni/Apollo)

Battery 12volt

Supplying, installation & testing of Smoke/Heat Detectors blinking LED type with mounting base complete as required. (Approx) (Make-Agni )

Suppling, installation & testing of Mannual Call Point. (Make-Agni)

Supplying, installation & testing of Speaker cum Electronic Hooter mounted with line matching transformer in automatically treated box complete as required. (20 Met. range) (Make-Agni)

Supplying, installation & testing of ARD FRLA Cable 2x1.5 Sq mm (Make- Polycab)

Providing & Fixing testing of Response Indicator (RI)

Supply of ABC Type Fire Extinguisher 4 Kg

Fire Liasioning Work For NOC

Providing & Fixing decorative structure glazing work , including cost of adhesive of approved quality. 5mm reflacted tougthend glass aluminium section 2’’x2’’-16 gauge Silicon weither proof 789

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete300 mm sweep 900 rpm

Supply of surya LED Batten 20 Watts 1150 mm

Supply and fixing of 3 pole 63 amp MCB 10 KA complete all respect accessories.

Supply of ADP Octagonal Pole single Arm 6 m. height. Compitable for post top range. as approved by Engineer in charge with making connection complete in all respect. (Rate taken from GeM) poles with single bracket

Supply & Installation of 70 watt LED Street light Yes Wled Luminaire Light approved by Engineer in charge complete in all respect. (Rate taken from GeM) Cat AA (seg.)

Supply of LT XLPE PVC aluminium armoured cable 3.5Cx120 Sq.mm 1100 volt.

Supply of LT XLPE PVC aluminium armoured cable 4Cx6 Sq.mm 1100 volt.

Supply/Febrication of INDOOR PANEL -1

Supply/Febrication of OUTDOOR FEEDEER PILLER -3

Drilling of 100 mm dia Mini Tubewell 100 meters deep by Rig machine as per unit estimate.

Supply of submersible pumping plant capable of delivering 200 lpm discharge at 150 m head, with electric motor to be operated on 415+\-10% volts, 3 phase, 50 c\s AC supply with 5m submersible cable.

Supply of stand by submersible pumping plant capable of delivering 200 lpm discharge at 150 m head, with electric motor to be operated on 415+\-10% volts, 3 phase, 50 c\s AC supply with 5m submersible cable

Supply,installation testing and commisioning (SITC) on turkey bassis for fully automatically pump automation control pannel of different capacities having intelligent unit having "" FIELD PROGRAMMABLE LOGIC CONTROLERS BASED ,SCADA OPERATED PUMPS motor start , run , control protect against fault automatically operated control and data Acquistion system system at pumping water supply schemes.50 hp of simplex make.

Power wiring and earthing material as per standards. Power wiring 1x3x10 sq.mm.

Supply of main piping and valves of 100 mm size having following items. 100 mm dia x 4.8mm thick column pipe in 3m length with inter-locking arrangement 100 M. 100 mm dia CI D\F sluice valve with hand wheel 2 Nos 100 mm dia CI D\F reflex valve 1 No 100x100x100 mm dia Tee 1 No 100 mm dia CI D\F bend 2 Nos. 100 mm dia MS D\F pipe of 1.5M length 2 Nos Ventury 1 No MS DI clamp 2 pair TW Cap 1 No Guages 1 set. Necessary nut, bolts and packings.

Supply of 25 mm thick rubber resistance insulated sheet of size 2m x 1m.

Installation and commissioning of pumping plant and accessories

Supply of electronically controlled, electrically actuated, diaphragm operated, chemical metering pump, wall mounting suitable for delivering up to 10 litres of chemical solution/ sodium hypochlorite solution per hour under maximum delivery pressure up to 10 Kg/cm2 and suction lift not less than 1.5metre with accessories.

Provision for 200 liters plastic tank for storage of sodium hypochloride including supply, cartage & installation at tubewell site including all material, labour, T&P etc complete.

Supplying, erection, testing and commissioning of 630A, 11KV, 3 phase, 50 Hz. metal clad, dead front, Single Board,VCB Panel, 500MVA repturing capacity having one incoming and outgoing as per specification and requirement.

Supplying, Receiving, erection, testing and commissioning of 800kVA, 11kV/415V, 3 Phase, 4 wire 50 Hz. Dry Type cast resin copper wound Transformer for indoor duty having on load circuit tap changer Tappings +10% to – 10% in steps of 1.25% for each step, WTI protection and temerature scanner, Doors limit switch and control wiring upto marshall box, cable box at primary and secondary end, shall be connected through cable with Winding Temperature Indicator, Marshel Box to connect control cable between HT panel and Transformer as per specification etc. completed as required.

Supplying, installation, testing and commissioning of 415V, 3 Phase, 50 Hz., 4 wire system, sheet steel clad, dust and vermin proof cubical and Indoor type floor mounted, free standing extendible type Main LT Panel with IP - 42 protection, compartmentalized design and fabricated out of 2 mm / 1.6 mm CRCA sheet steel complete with Aluminium Bus bars, Electrical interlocks as per the various status of all the equipments indicated on the drawings. Providing & Fixing of base plate / channel, P/F the following Switchgears, complete with earth Bus bar throughout the length of the panel, terminal arrangement for Incomings / Outgoings cables and also outgoing terminations for various sizes of cables, The incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement, adequate size bus duct/cable alley, Sign writing, Painting, Earthing, Numbering, Danger plate etc. complete as required as per specifications and drawing. INCOMING: 1 no. 1250A 415V, 4P 50kA EDO ACB with Microprocessor based release having O/L, S/C/ , E/F , O/V, U/V Protection and ON /OFF/TRIP Indications with MCB. 4 nos. Digital type Multifunction Meters to show (V, A, kWh, KVAh, KW, KVA, KVAR, PF, Hz.) with cast resin CTs.and communication port. 4 Set of LED phase indicating lamps with MCB protection. 3 nos. Trip Circuit Supervision relays. 1 no. 25kVAR capacitor bank with 63A TP isolator, with one set of indicating Lights. 1 no. Auto matic power factor correction relay. 1 no. TPN surge protection device of Class 1 & 2. BUSBARS: 1 Set of TPN aluminium bus bar of minimum of 1250 A capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc, for withstanding fault level of 50 KA for 1 Sec. Electrical Interlocking between all incomers and Bus Couplers through PLC . BUS COUPLER : 1 no. 800A 415V, 4P 50kA EDO ACB with inbuilt O/L, S/C Protection and ON /OFF/TRIP Indications with MCB. OUTGOING 3 no. 500A 415V, TP+Neutral Link MCCB of 50kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 3 nos. 250A 415V, TP+Neutral Link MCCB of 50kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 2 nos. 200A 415V, TP+Neutral Link MCCB of 50kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 3 nos. 160A 415V, TP+Neutral Link MCCB of 50kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 4 no. 63A 415V, TP+Neutral Link MCCB of 50kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. The synchronising among the DG Sets shall be obtaimed through the DG set controller, however DG Sets Auto ON/ OFF / load management among the DG Sets and the Interlocking between all the Incomers and the bus coupler shall be obtained through a PLC mounted installed in the Main LT Panel.The panel shall be complete with the Battery charger of the each DG Set and the DC supply / UPS for the relay , protection and PLC supply, the panel shall be complete as per specifictions and single line diagram as required.

COMMON UTILITY PANEL (FLOOR PANEL) INCOMER : 1 No. 160A, 415V, Ics=36kA, 4P MCCB with Microprocessor based release having O/L, S/C/ , E/F , O/V and U/V Protection. 1 Nos. Digital type Multy Function Meters to show (V, A, kWh, KVAh, KW, KVA, KVAR, PF, Hz.) with cast resin CTs.and communication port. 1 set of Phase indicating lamp with MCB 1 no. TPN surge protection device of Class 1 & 2. BUS BARS: 1 Set of TPN aluminium bus bar of minimum of 300 A capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc, for withstanding fault level of 36 KA for 1 Sec. OUT GOING: 5 nos. 63A 415V, TP+Neutral Link MCCB of 36kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 3 nos. 40A 415V, TP+Neutral Link MCCB of 36kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port.

UPS PANEL-1 (HOSPITAL BLOCK) INCOMER : 1 No. 100A, 415V, Ics=36kA, 4P MCCB with Microprocessor based release having O/L, S/C/ , E/F , O/V and U/V Protection. 1 No. Digital type Multy Function Meters to show (V, A, kWh, KVAh, KW, KVA, KVAR, PF, Hz.) with cast resin CTs.and communication port. 1 set of Phase indicating lamp with MCB 1 No. TPN surge protection device of Class 1 & 2. BUS BARS: 1 Set of TPN Cu. bus bar of minimum of 300 A capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc, for withstanding fault level of 36 KA for 1 Sec. OUT GOING: 2 nos. 100A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection. 2 nos. 63A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection. 2 nos. 40A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection.

UPS PANEL-2 EMERGENCY LIGHT (HOSPITAL BLOCK) INCOMER : 1 No. 63A, 415V, Ics=36kA, 4P MCCB with Microprocessor based release having O/L, S/C/ , E/F , O/V and U/V Protection.1 No. Digital type Multy Function Meters to show (V, A, kWh, KVAh, KW, KVA, KVAR, PF, Hz.) with cast resin CTs.and communication port. 1 set of Phase indicating lamp with MCB 1 No. TPN surge protection device of Class 1 & 2. BUS BARS: 1 Set of TPN Cu. bus bar of minimum of 200 A capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc, for withstanding fault level of 36 KA for 1 Sec. OUT GOING: 2 nos. 63A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection. 3 nos. 40A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection. 3 nos. 25A 415V, TP+Neutral Link MCCB of 35kA with thermal release, O/L and S/C protection.

LIFT PANEL INCOMER : 1 no. 125A, 415V, 4P ATS. 1 Nos. 125A, 415V, Ics=36kA, 4P MCCB with Microprocessor based release having O/L, S/C/ , E/F , O/V and U/V Protection. 1 Nos. Digital type Multy Function Meters to show (V, A, kWh, KVAh, KW, KVA, KVAR, PF, Hz.) with cast resin CTs.and communication port. 1 set of Phase indicating lamp with MCB 1 no. TPN surge protection device of Class 1 & 2. BUS BARS: 1 Set of TPN aluminium bus bar of minimum of 300 A capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc, for withstanding fault level of 36 KA for 1 Sec. OUT GOING: 4 nos. 63A 415V, TP+Neutral Link MCCB of 35kA with Microprocessor release, O/L and S/C protection and a set of CT's., Multi Function meter (V+A+Hz.) with communication port. 2 nos. 25A 220V,DP MCB of 10kA.

MAIN DISTRIBUTION BOARD Supplying, fixing ,testing and commissioning of 415V, 3 Phase, 50 Hz., 4 wire system, sheet steel clad, dust and vermin proof cubical and indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2 mm / 1.6 mm CRCA sheet steel complete with Aluminium Bus bars, Providing & Fixing of base plate / channel, P/F the following Switchgears, complete with earth Bus bar throughout the length of the panel, terminal arrangement for Incomings / Outgoings cables and also outgoing terminations for various sizes of cables, The incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement, adequate size bus duct/cable alley, Sign writing, Painting, Earthing, Numbering, Danger plate etc. complete as required as per specifications and drawing. INCOMER : 1 no. 160A, 415V, Ics=35kA, 4P MCCB with thermal magnetic trip unit. 1 no. Digital multifunction meter (V+A+Hz) with a set of cast resin CTs 150/5A and communication port. 1 set of Phase indicating lamp with MCB 1 no. TPN surge protection device of Class 1 & 2. BUS BARS: 300A TPN bus bars of aluminium alloy. OUT GOING: 5 nos. 63A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 7 nos. 40A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 4 nos. 40A 220V,DP MCB of 10kA. 4 nos. 25A 220V,DP MCB of 10kA.

LIGHT + POWER MDB- (FIRST FLOOR) INCOMER : 1 no. 250A, 415V, Ics=35kA, 4P MCCB with thermal magnetic trip unit. 1 no. Digital multifunction meter (V+A+Hz) with a set of cast resin CTs 250/5A and communication port. 1 set of Phase indicating lamp with MCB 1 no. TPN surge protection device of Class 1 & 2. BUS BARS: 300A TPN bus bars of aluminium alloy. OUT GOING: 10 nos. 63A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 3 nos. 40A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 3 nos. 25A 220V,DP MCB of 10kA.

LIGHT + POWER MDB- (SECOND FLOOR) INCOMER : 1 no. 200A, 415V, Ics=35kA, 4P MCCB with thermal magnetic trip unit. 1 no. Digital multifunction meter (V+A+Hz) with a set of cast resin CTs 250/5A and communication port. 1 set of Phase indicating lamp with MCB 1 no. TPN surge protection device of Class 1 & 2. BUS BARS: 300A TPN bus bars of aluminium alloy. OUT GOING: 8 nos. 63A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 3 nos. 40A, 415V, Ics=25kA, TP +Neutral Link MCCB with thermal magnetic trip unit. 6 nos. 25A 220V,DP MCB of 10kA.

DG SET Providing ,Installing and commissioning of Radiator colled Silent type Diesel generator set along with having Prime Power rating of 500 kVA ,415 volt at 1500 Rpm,0.8 lagging power factor at 415 v suitable for 50 Hz, 3 phase system & 0.8 load factor and consisting of following Diesel Engine Diesel Engine 4 stroke water cooled ,Electric start of suitable BHP AT 1500 RPM suitable for above output of alternator at 40 degree c,50 % RH & at 1000 meter MSL and conforming to BS 5514,BS 649,IS 10000,Capable of taking 10 % overloading for one hour after 12 hour of continuous operation. The engine will be fitted complete with all required accessories Engine mounted instrument panel fitted with and having digital display for following Start -stop switch with Key water temperature indication Lubrication oil pressure indication Lubrication oil temperature indication Battery Charging Indication RPM Indication Over speed indication Low Lub. Oil trip indication Engine Hours indication Alternator Synchronous alternator rated at 500 KVA,415 volts at 1500 Rpm ,3 Phase 50 Hz,AC supply with 0.8 Lagging power factor at 40 Degree C,50 % RH & at 1000 Metre MSL.The alternator shall be having SPDP enclosure,Brushless,Continous duty, Self excited and self regulated through AVR conforming to IS: 4722/BS 2613 suitable for tropical condition and with class-F/H insulation Base Frame &Foundation Both the engine and alternator shall be mounted on suitable Base frame made up of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer Exhaust System Dry exhaust manifold with hospital exhaust silencer and catalytic convertor Acoustic and weather proof enclosure with arrangement fresh air intake for cooling of the engine & alternator,extraction,discharging hot air in to the atmosphere as per specification

Supply, fixing and commissioning 990 ltrs capacity 16 SWG MS steel, Disel oil Tank with manhole, PVC gauge, inlet and outlet connections with gate valve, drain plug, piping between tank and engine vent etc. mounted on suitable MS staging to maintain gravity flow of diesel oil FRLSom tank to DG set including painting etc. as required.

Supplying of 3 core 240 sq.mm XLPE AL. Armoured cable, 11kV grade in Treanch as per specification

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 3.5C x 185 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 3.5C x 150 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 3.5C x 95 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 3.5C x 70 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 3.5C x 50 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 4C x 35 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 4C x 25 sq.mm. AL. ARM. XLPE cable

Supplying the following 1100V grade XLPE Insulated Aluminum Conductor Armoured cables, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. 4C x 16 sq.mm. AL. ARM. XLPE cable

15KVA UPS (OT) Supply Installation, Testing & Commissioning of microprocessor based 15 kVA UPS, with IGBT based Rectifier and Inverter with Unity Output Power Factor i.e. 15 kVA/15 KW. UPS Should be True Online Double Conversion (VFI as per IEC62040-3). 3Phase input & 3 Phase output each comprising of the following. (Suitable for parallel operation) 3 Level Inverter Technology with Double Conversion Efficiency > 95% for 50% and above load. THD(i) shall be less than 5% @ 100% load. Input power factor shall be more than 0.98. from 50% to 100% load Shall have Soft start Facility for Compatibility with Generators Invertor capability to supply 125% for 10 minutes & 150% load for 60 sec. Shall not allow deep discharge of the battery. There should be a external MCCB available with UV trip coils. The MCCB should disconnect itself in case of UV or emergency conditions. Shall have inbuilt SNMP/Modbus Cards installed for monitoring on BMS. Shall have inbuilt Dust Filters Shall have Conformal Coating on PCBs UPS shall have facility to test @100% Load with or without External Load Bank. Vendor to provide External Load Bank of 15 kW incase inbuilt feature not available. Load Bank to be kept at site only during the entire Warranty Period of the UPS. Shall have EPO switch on the UPS Front. Osillosope / PM Meter to be provided for Waveform Capturing during the event failure for RCA's. UPS to have inbuilt Static By-pass enabled

Supply, fixing, testing and commissioning of battery Bank of 15KVA UPS at 0.9 output power factor strictly as per specification given in the document. Each individuals UPS of 15KVA shall have 30 min. battery back up. Battery Racks, Intercool & Inter Tier Connectors for the battery Banks, External MCCB with UV coils and UPS to Battery Cables for a distance of 20 mtrs.The battery shall comprise of 12 volt cell and size and combination of bank in terms of VAH shall be clearly mentioned with battery claculation with invertor efficiency as 0.95 or more, end of cell voltage shall be taken as 10.5 volts.

Stainless Steel 304 Grade min. 1.5mm thk Pre Fabricated Modular Operation Theatre Wall Panel and Ceiling panel backed with 12mm thick. Gypsum with proper supports as per specification. Make – Sigma/ Shree anand/ Mediasha

Filling of Joints ,Cavity and Antibacterial painting:- Filling of all joints & cavities with epoxy filler, sanded flush for seamless finish with one primer and three coats of antibacterial & antifungal paint . That is equivalent to a dry film thickness of 300 microns as per specification

Hermetically Sealed automatic sliding doors:- Automatically Operated hermetically sealed Sliding Doors of different size as required with glass vision window of 300mm x 300mm (WXH) along with all required accessories and in colour approved by client as per specification.Make- Metaflex/ Reboon Door size 1500 mm X 2100 mm

Hermetically Sealed automatic sliding doors:- Automatically Operated hermetically sealed Sliding Doors of different size as required with glass vision window of 300mm x 300mm (WXH) along with all required accessories and in colour approved by client as per specification.Make- Metaflex/ Reboon Door size 1000 mm X 2100 mm

Laminar airflow System:- Laminar Plan air Ceiling system of size (2400mmx2400 mm) with unidirectional airflow with "S" class HEPA filter with an efficiency 99.97% down to 0.3 micron. The holding structure & top plenum are made up of Aluminium Sheet with a thickness of 1.6mm. It should be sealed with gasket conforming to DIN 4799 standards for the air distribution system. 2 layer diffuser with monofilament precision woven polyester of uniform porosity with an open area of sufficient resistance to create laminar from diffusers face and integral lighting provides an illumination level in excess of 15000 Lux in operating area and 10000 Lux other with flicker less digitally controlled steeples dimming down to 5%. Make – Sigma/ Shree anand/ Mediasha

Electrical wiring - Electrical wiring within the OT Area, conduit pipes and electrical switch & Socket with Electrical Distribution board for Operating room with MCB's and Relay cards. All wiring should be done through ISI mark copper wire only with conduit pipe..

Peripheral lights:- Recess mounted IP 54 protocol, non-hygroscopic Peripheral Lights for clean room application. Each light set having 2 nos of 36 watt fluorescent lamps with digitally controlled dimmable ballast. Make – Sigma/ Shree anand/ Mediasha

Scrub Sink:- scrub sink made out of 304 graded brushed finished stainless steel, with photo electric sensors,1 No. Mixture valve, 2 nos. solenoid valves with Foot operated switch as per specification. Make – Sigma/ Shree anand/ Mediasha Scrub Sink 2 - bay.

Writing board:- It should be flush mounted with a sterile jointing system, 1.50mm thick, white Ceramic board, bonded to a 2 mm steel sheet for additional rigidity. Approximate size of the same should be 940 x 600 mm. Make – Sigma/ Shree anand/ Mediasha

X-ray view box:- Twin Plate X-Ray viewing screen with flicker free dimming light range from 15 to 100% with complete accessories as required to view the X-ray film. Make – Sigma/ Shree anand/ Mediasha

Control Panel:- Touch Panel type Operation Theatre Control Panel (6 service Tiles) mounted. Flushed in the theatre wall with complete distribution board with all accessories. Make – Sigma/ /Digiline /Altos Following are the controls/ display available:- * 1 no Day Time Digital Clock. * 1 no Elapsed Time Digital Clock. * 1 no Hands Free Telephone system. * Peripheral Light Control * Medical Gas Alarm for 4 gases. *Temperature & Humidity Indicator . * Alarm for Vacuum.

Dirty Hatch box:- Dirty hatch box made up of Stainless steel grade 304, having two doors on both side. One door will be opened at one time , indicator on both sides in case of door is open. The hatch will be designed in such a way that only one door will be opened at one time. The UV light will glow when both the doors are in closed position. Make – Sigma/ Shree anand/ Mediasha

LED Operating light: - Ceiling mounted Operating room Dual Dome Light CE Notified and US FDA approved with provision of camera in it.

160000 Lux + 160000 Lux and o Colour rendering index CRI>95 and R9 ≥ 91 to 97 as per specification. Make- Steris/Luvis/ Draegar/Trilux Ceiling Pendants:- Ceiling Pendent with weight carrying capacity of 100Kg. The pendant should have 10-12 electrical sockets, one monitor shelf and instrument Drawer IV Pole and infusion Pump Rod mount on it. system must be CE notified or US FDA approved for quality parameter. Gas outlets for pendants will be provide by user/department for compatibility with hospital wards. for connection of gases to pendant required copper pipe point near to pendant will be provide by department/MGPS contractor. Double Arm surgeon pendant

160000 Lux + 160000 Lux and o Colour rendering index CRI>95 and R9 ≥ 91 to 97 as per specification. Make- Steris/Luvis/ Draegar/Trilux Ceiling Pendants:- Ceiling Pendent with weight carrying capacity of 100Kg. The pendant should have 10-12 electrical sockets, one monitor shelf and instrument Drawer IV Pole and infusion Pump Rod mount on it. system must be CE notified or US FDA approved for quality parameter. Gas outlets for pendants will be provide by user/department for compatibility with hospital wards. for connection of gases to pendant required copper pipe point near to pendant will be provide by department/MGPS contractor. Single Arm Anaesthesia Pendant

SITC of Pressure relief damper: - Pressure Relief Damper. Made up of 304 graded stainless-steel blades with all required accessories. It opens to maintain balanced positive pressure inside OT and prevent air contamination from outside. Make – Sigma/ Shree anand/ Mediasha

Storage Cabinet:- Equipment Storage Unit is to be provided in operating theatre of dimension approved in the user. Approximate size of the unit should be 860(W) x1660(H) x350(D) mm and it should be flush mounted into the theatre wall with a sterile jointing system. Make – Sigma/ Shree anand/ Mediasha

Anti - Static flooring: - 2mm thick Anti-static, conductive dissipative flooring tile laid on a semi conductive adhesive base resistant to mechanical stress and dynamic load and washable. Its include all required flooring and levelling work for proper sloping of OT floors. it should be finished with proper sealed coving with wall to prevent water leakage in flooring at time of wash. Make – Tarket / Grflor/ GE

Medical Gas pipeline system: inside OT FOR Medical Gases including all fitting and fixtures, that all pipes should be tapped through main corridor medical gas pipes by only the main medical gas services contractor. etc complete as required as per specification.

Lockable CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Medicop/ Silbermann/Ohio Having data logging facility LCD Touch panel software menu-based control and supervision Must have Gas Pressure & Temperature alarm facility LED digital display, audio visual feature Must have emergency feed facility in case of shutdown for interrupted supply SS sheet construction, CE certified/UL Listed with relevant notified no. on it as required, entry/ exist of gases from upward direction 5 Services (Oxygen, MA-4, MA-7, Nitrous Oxide, Vacuum)

online ups of capacity 10 KVA with 30 min Backup as per specification Make- 3EM/DIgiline/Microtek/UTL

View window with motorized blind of size min 1m x1m completely sealed Make – Sigma/ Shree Anand/ Window-Tech

MEDICAL AIR COMPRESSOR SYSTEM, multi drive control mode, Screw air compressor with foundation, Filtration system, receiver, electrical connection from compressor to control panel and all as required as per specification. Entire system shall be installed as a package and compatible to fulfil the demand of system. Product should be as per specification. Compressor Make- Hitachi/ Atlas Copcoo/Ohio/Dewalt Main component of system is as below Air compressor with capacity 57CFM. (+/- 5%) with suitable motor as required (4 nos.) Air receiver tank 2500 ltr Air filtration Set as per specification (2 nos. for Duplex) Air dryer suitable capacity (2 nos. for Duplex) Air Pr. Reducing Station 4-Bar & 7-Bar (Duplex)

SITC of Duplex MEDICAL VACUUM SYSTEM. The package shall consist of Reciprocating Vacuum pumps (including civil foundation and electrical wiring of suitable capacity from Pump to electrical panel and non-return valve complete) with suitable hp motor. The vacuum pump, motor and associated accessories shall be installed as a package by the manufacturer/installer, and not as discrete items. Complete system is as per specification. As per approved make attached. Reciprocating Vacuum Pump With capacity 4200 Ltr (+/- 5%) with suitable Motor (2 nos.) Pressure Switch Vacuum Receiver tank 3000 Ltr. (Total Capacity) Silencer muffler type Vacuum Bacterial Filter (2 nos. for Duplex)

SITC of OXYGEN MANIFOLD minimum of 2x8 cylinders oxygen manifold extendable type with middle frame along with tail pipe as size given in the drawings having top frame comprising of high-pressure copper pipe with high pressure brass fitting made of high tensile brass, NRV and high-pressure copper tailpiece made of high-pressure copper pipe. 1x8 bank shall be a reserve source of oxygen supply. It shall automatically supply the pipeline when primary source becomes exhausted or fails due to any reason. The system shall have source shut-off valve for easy changing and positioning, without hook. The cylinder should be placed with the help of cylinder brackets and fixing chains which should be zinc plated appropriate. (Gas cylinders are not in the scope of this work). Product should be as per specification. Make- Sigma / Mediasha/ Medimatic

S.I.T.C of Imported CE Marked compliant with HTM or NFPA Oxygen Change-Over Reduction Box (Automatic Control Panel) of Digital fully Automatic type, capable of switching from “Bank in Use” to “Reserve Bank” without fluctuation in delivery line pressure and without the need for external electrical power. The Changeover panel shall be rated for min. 80 QMH at 400 kPA, and shall include the following accessories. Panel shall comply with HTM/ISO as per specification. Make- Ohio / Silbermann/ Medicop Main component / feature of system is as below Power Supply Module to provide power supply for alarm system display Signalling Module for Pressure monitoring and Alarm Activation Double line pressure Regulator High and Low Limit Pressure Switches Changeover and safety valve Pressure Adjustment system (for working Pressure) Touch panel (LCD Display) software menu-based control and supervision Able to display running Pressure & flow of gases Pressure Transmitter for Working Pressure Indication easily upward opening with damper hinged door Panel constructed with Stainless Steel material having data logging facility for consumption & current flow of gases able to interface with network to provide real time supervisio

Oxygen Emergency System (2+2): - The oxygen emergency system contains 4 nos. Gas cylinder manifold along with copper header, Brass Non-Return valve & High- pressure copper tail pipe for each cylinder complete. product should be as per specification. Make- Sigma / Mediasha/ Medimatic

NITROUS OXIDE SUPPLY SYSTEM SITC of NITROUS OXIDE MANIFOLD SYSTEM minimum of 2 x2 cylinders and reserve source of nitrous oxide will be 2x1 cylinders. Cylinder size shall be as given in the drawings having top frame comprising of high pressure copper pipe with high pressure brass fitting made of high tensile brass, NRV, high pressure copper tailpiece made of high pressure copper. Reserve source of N2O shall automatically supply the pipeline when primary source of supply become exhausted or fails due to any reason. (Gas cylinders are not in the scope of this work). Product should be as per specification. Make- Sigma / Mediasha/ Medimatic

S.I.T.C of Imported CE marked Nitrous Oxide Change-Over Reduction Box (Automatic Control Panel conforming to HTM/ ISO ) of Digital fully Automatic type, capable of switching from “Bank in Use” to “Reserve Bank” without fluctuation in delivery line pressure and without the need for external electrical power. The Changeover panel shall be rated for min. 50 QMH at 400 kPA, and shall include the following accessories. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Main component / feature of system are as below Power Supply Module to provide power supply for alarm system display Signalling Module for Pressure monitoring and Alarm Activation Double line pressure Regulator High and Low Limit Pressure Switches Changeover and safety valve Pressure Adjustment system (for working Pressure) Touch panel (LCD Display) software menu based control and supervision Able to display running Pressure & flow of gases Pressure Transmitter for Working Pressure Indication easily upward opening with damper hinged door Panel constructed with Stainless Steel material having data logging facility for consumption & current flow of gases able to interface with network to provide real time supervision

Nitrous Oxide Emergency Manifold: - The Nitrous Oxide Emergency system contains 2 Nos Gas cylinder manifold along with copper header, Brass Non-Return valve & High- pressure copper tail pipe for each cylinder and one number of high-pressure regulators. product should be as per specification. Make- Sigma / Mediasha/ Medimatic

MASTER ALARM & GAS SUPERVISION SYSTEM Plant/Master Gas Alarm: - Imported CE marked (with CE Number) Master Gas Alarm for 4-gases conforming to HTM/NFPA. This panel shall be able to test Short Circuit Fault, Open Circuit Fault, Source Equipment Fault and include the a) Dual Circuit LED Indicators. b) Test facility to check LED c) Test facility to check LED Integrity. Panel shall be equipped with Micro-processor-based alarm. product should be as per specification. Make- Ohio / Silbermann/ Medicop

Combined Electrical Control Panel for Medical Air Compressors & Vacuum Pumps as per specification with all required support foundation complete

Terminal Outlets: - Terminal Outlets gas specific for the services indicated (viz. O2, Air & Vacuum) and to accept only compatible quick connect Pin/Geometric Index type adapters as HTM/NFPA standard, CE Certified/UL Listed as required. product should be as per specification. Make- Sigma / Mediasha/ Medimatic Oxygen Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Make- Sigma / Mediasha/ Medimatic Oxygen Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Make- Sigma / Mediasha/ Medimatic Vacuum Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Make- Sigma / Mediasha/ Medimatic MA-4 Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Make- Sigma / Mediasha/ Medimatic SA-7 Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Make- Sigma / Mediasha/ Medimatic Nitrous Oxide Outlet

Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Having data logging facility Touch panel software menu-based control and supervision Must have Gas Pressure & Temperature alarm facility LED digital display, audio visual feature Must have emergency feed facility in case of shutdown for interrupted supply SS sheet construction, CE certified/UL Listed with relevant notified no. on it as required, entry/ exist of gases from upward direction 3 Services (Oxygen, MA-4, Vacuum)

Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Having data logging facility Touch panel software menu-based control and supervision Must have Gas Pressure & Temperature alarm facility LED digital display, audio visual feature Must have emergency feed facility in case of shutdown for interrupted supply SS sheet construction, CE certified/UL Listed with relevant notified no. on it as required, entry/ exist of gases from upward direction 4 Services (Oxygen, MA-4, Nitrous Oxide, Vacuum)

Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Gas lockable AVSU/CONTROL-CLOSING VALVE BOXES (INTEGRATED WITH AREA ALARM) with integrated alarm system as per specifications, and as required. Product should be as per specification. Make- Ohio / Silbermann/ Medicop Having data logging facility Touch panel software menu-based control and supervision Must have Gas Pressure & Temperature alarm facility LED digital display, audio visual feature Must have emergency feed facility in case of shutdown for interrupted supply SS sheet construction, CE certified/UL Listed with relevant notified no. on it as required, entry/ exist of gases from upward direction 5 Services (Oxygen, MA-4, MA-7, Nitrous Oxide, Vacuum)

Modular bed head panel, with provision of gas outlet, electrical, 1200 mm long, made of high grade of aluminium. Fabricated by extrusion method and powder coated as per approved colors.as per specification and drawing. Make- Sigma / Mediasha/ Medimatic

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 12 mm OD

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 15 mm OD

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 22 mm OD

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 28 mm OD

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 42 mm OD

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to MBS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc. Make- Mexflow/ Mandev/ Janya 54 mm OD

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 12 mm

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 15 mm

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 22 mm

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 28 mm

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 42 mm

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Legris/CIM 54 mm

Oxygen Flow Meter - Made from brass, chrome plated. It shall be back pressure compensated type having housing of Polycarbonate autoclavable reusable flow range 0-15 LPM. Fitted with matching adopter for oxygen outlet point and humidifier shall be compatible with flowmeter and reusable and as per specifications and as required. Product should be as per specification. Make- Sigma / Mediasha/ Medimatic

Ward Vacuum Unit - Regulator capable of controlling vacuum between 0 to 760 mm Hg and Polycarbonate autoclavable, reusable type receiver jar of not less 600 ml. Vacuum regulator shall have a dial gauge, on/off switch, valve control knob and as per specifications and as required. Product should be as per specification. Make- Sigma / Mediasha/ Medimatic

Low pressure suction tube for suction outlet adopter as required

Operation Theatre Suction Trolley- having 2 Nos. 2000 ml receiver jars of Polycarbonate autoclavable up to 121 *C, reusable and mounted on trolley with wheel arrangement. The trolley shall have one number of vacuum regulators having regulation control between 0-760 mm Hg and interconnecting suction tubes. Product should be as per specification. Make- Sigma / Mediasha/ Medimatic

OT Conversion kit attached with 5 Mtr Long HP tube with appropriate colour code for specific gas. Make- Sigma / Mediasha/ Medimatic KIT for oxygen

OT Conversion kit attached with 5 Mtr Long HP tube with appropriate colour code for specific gas. Make- Sigma / Mediasha/ Medimatic KIT for Nitrous Oxide

OT Conversion kit attached with 5 Mtr Long HP tube with appropriate colour code for specific gas. Make- Sigma / Mediasha/ Medimatic Kit for Air 4

Installation, testing and commissioning Outdoor Units ODU : 16 HP

Installation, testing and commissioning Outdoor Units ODU : 14 HP

Installation, testing and commissioning Indoor units Hi-Wall Type Unit

Installation, testing and commissioning Indoor units 4-Way Cassette Type Unit

Commissioning of VRF Setfree systems including topping R410A gas per site requirements

Supply, Installation, testing and commissioning of the insulated refrigerant piping for all the units with the refnets as per the specs. The insulation shall be of 13/19 mm thick nitrile rubber make through out the running length of the refrigerant piping. The piping shall be well supported at specifications Copper Piping for VRF

Providing and fixing rigid PVC piping complete with fittings, supports as per OEM STD and duly insulated with 6 mm thick closed cell nitrile rubber insulation. 25 mm dia

Providing and fixing rigid PVC piping complete with fittings, supports as per OEM STD and duly insulated with 6 mm thick closed cell nitrile rubber insulation. 32 mm dia

supply & fixing of control cum transmission wiring of shielded Copper conductor cable alongwith Pvc conduite for looping between indoor & outdoor VRF system & to main Central remote controller system 2 C X 1.5 Sq. mm

supply & fixing of control cum transmission wiring of shielded Copper conductor cable alongwith Pvc conduite for looping between indoor & outdoor VRF system & to main Central remote controller system Lifting & Shifting of Indoors and Outdoors units

Comprehensive AMC (ANNUAL MAITINENCE COST) AFTER ONE YEAR WARRANTY 1st Year

Comprehensive AMC (ANNUAL MAITINENCE COST) AFTER ONE YEAR WARRANTY 2nd Year

Comprehensive AMC (ANNUAL MAITINENCE COST) AFTER ONE YEAR WARRANTY 3rd Year

1. Providing & fixing of sticker pasted acrylic name plates for rooms including all its labour, complete in all respects as per directed by engineer in charge MARKET RATE

PACKAGE ETP CUM STP IN CIVIL CONSTRUCTION CLIENT:-PROJECT:-Proposed Hospital Site At Haidwar PLANT CAPACITY:- STP -50 KLD , ETP- 5 KLD

ELEGANT INFRA DEVELOPERS (BID ID -385096)