Repair and maintenance of State Sports Hostel at Luhnu Distt Bilaspur HP including internal Water Supply Sanitary Installations

Amount

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work, blasting work and chiselling/wedging out of hard or soft rock (where blasting is prohibited) up to all heights stacking the excavated soil not more than 3 meters clear from the edge of excavation and then returning the stacked soil in15 Cms, Layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge in all leads and lifts.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering,strutting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of material in all leads & lifts:-

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etc. up to 200mm in thickness

Edges of slabs and breaks in floors and walls. Under 20 cm. Wide.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centering and shuttering in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work including carriage of material in all leads and lifts:- Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and contilever upto floor two level.

Providing and laying cement concrete 1:8:16 (1cement: 8sand:16graded stone aggregate 20mm. nominal size) and curing complete on slab and floor excluding the cost of form work screed laid under flooring.including carriage of material in all leads and lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete including cost of binding wire up to all heights including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:4(1cement:4sand) including carriage of material in all leads and lifts.

Brick work 7.62 cm. thick in Cement Mortar 1:3 (1 cement:3 sand) using 2nd class common burnt clay building bricks including carriage of material in all leads and lifts.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws including carriage of material in all leads and lifts:- 40 mm thick

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of material in all leads and lifts:- 40 mm thick.

Providing and fixing anodized aluminium sliding door bolts and anodized colour and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts:- 250x16mm

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws, nuts, bolts etc. complete including carriage of material in all leads and lifts:-

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws, nuts, bolts etc. complete including carriage of material in all leads and lifts:-

Providing and fixing bright finished hard drawn M.S. hooks and eyes including cost of screws with wooden chowkhats including carriage of material in all leads and lifts. 150mm.

Providing and fixing 65x35mm special quality chromium plated brass cup board lock with six leavers including necessary screws etc. complete (Indian make) including carriage of material in all leads and lifts

Providing and fixing oxidized M.S. safety hasps and staples with necessary screws etc. complete 115 mm including carriage of material in all leads and lifts.

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge. For doors windows and ventilatiors and glazed partitions frames including carriage of material in all leads and lifts.

For doors windows and ventilatiors and glazed partitions frames.

. For shutters of doors indows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings.

Providing and fixing Bakelite sheet in door shutters including carriage of mateial in all leads and lifts.

Glazed tiles 6mm thick (any size/colour) in skirting riser of steps and dado 12mm thick cement mortar 1:3(1cement:3sand) and jointed with white cement slurry including carriage of material in all leads and lifts.

Cement concrete flooring 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of material in all leads and lifts:- 50mm thick.

Kota stone slab flooring 20mm (average) thick base of cement mortar 1:4 (1cement:4sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete 25mm thick including carriage of material in all leads and lifts.

Kota stone slab 25mm thick in risers of steps skirting dado and pillars laid on 12mm (average) thick cement mortar 1:3(1cement:3sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of material in all leads and lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles nitco or equivalent (any size and colour ) 10mm thick manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm thick cement mortar 1:3 (1cement:3sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including cost of tiles where required to be cut and carriage of material in all leads and lifts.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material in all leads and lifts :-

In beams, joists, channels angles, tees, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafter and the like.

In gratings, framed guard, bars, ladders, railing, brackets and similar works.

Providing and fixing pressed steel door frames manufactured from commercial mild steel sheet of 1.66 m thickness including hinges, lock, jambs, beeds and if required angle threshold of mild steel angle of section 50x25mm or base ties of 1.6mm pressed mild steel welded or rigidly fixed together by steel butt hinges 2.5mm thick with guards, lock strike plate and shock absorber as specified and applying a coat of approved steel primer after pre-treatment of the surfaces as directed by the Engieneer-in-charge including carriage of material in all leads and lifts.

Profile – A.

Profile – B (double rebated).

Providing and fixing 1mm thick M.S. sheet garrage door with frame of 40mmx40mm6mm angle iron 3.15mm M.S. gusset plates at the junctions and corners, all necessary fittings complete including applying a priming coat of red lead paint Using M.S. angle 40mm x40mmx6mm for diagonal braces including carriage of material in all leads and lifts.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give fair and smooth surface including cleaning the surface of all dirt, dust, dust and other foreign matter:-Enamel paint other than white including carriage of material in all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering and knotting Ready mixed paint brushing wood primer pink including carriage of material in all leads and lifts.

Painting one coats (excluduing priming coat) on previously painted wood and wood based surfaces with enamel paint to give an even shade on ceilling including cleaning the surface of dirt, dust and other foreign matter sand papering and stoping including carriage of material in all lead in all leads and lifts:- With enamel paint other than white.

Extra for fevery subsequent coat of paint on wood based surface including carriage of material in all lead in all leads and lifts:- With enamel paint other than white.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces two coats to give an even shadae and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete including carriage of material in all leads and lifts.

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:-In cement mortar 1:6 (1cement: 6 sand)

20mm cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:- In cement mortar 1:6 (1cement: 6 sand)

Distempering(one coat) with oil bound washable distemper of approved brand and manufature and of required shade,on decorated ceilling to give an even shade,after thoroughly brushing the surface clean of all grease,dirt,loose pieces of scales and also including preparing the surface even and sand papered smooth including material in all leads and lifts.

Extra over item No 35.00 for fevery subsequent coat of oil bound washable distemper of approved brand and manufature.

Distempering(one coat) with oil bound washable distemper of approved brand and manufature and of required shade,on decorated wall surfaces to give an even shade,after thoroughly brushing the surface clean of all grease,dirt,loose pieces of scales and also including preparing the surface even and sand papered smooth including material in all leads and lifts.

Extra over item No 37.00 for every sub sequent coat of distempering with oil bound washable distemper of approved brand and manufacture.

Supplying and fixing glass panes with putty and nails including removal of broken glass panes wherever necessary including carriage of material in all leads and lifts

Dismantling tiled floors laid in mortar upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead (wooden/concrete joists to be measured and paid for separately) including carriage of material in all leads and lifts For thickness of tiles above 25mm and upto 40mm .

Demolition below G.L. upto 1.50 Metres depth and disposal of unserviceable materials within all lead. Un-reinforecd cement concrete upto 15 cm. thickness including carriage of material in all leads and lifts

Dismantling doors, windows and clerestory windows, ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other ttachements etc. complete and stacking them within 20 metres lead. Not exceeding 3 sq.m in area

Providing and fixing to wall ceiling and floors galvanized mild steel tubes (Medium grade) tube fittings and clamps including making good the wall, ceiling and floors, including carriage of material in all leads and lifts, confirming to BIS specification:-

15mm nominal bore.

20mm nominal bore.

Providing and fixing vitreous china wash down water closet (European type W.C. pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:1(1cement:1sand) (seat and cover to be measured and paid for separately including carriage of material in all leads and lifts:- Ordinary closet.

Providing and fixing vitreous china water closet squatting pan (Indian type WC pan) size 580mm (earth work bed concrete, foot rest and trap to be measured and paid for separately) including carriage of material in all leads and lifts. Orissa pattern confirming to BIS specification.

Providing and fixing sand cast iron 100 mm size “P” or “S” trap (ISI marked) for water closet squatting pan including jointing the trap with the pan and soil pipe in cement mortar 1:1(1cement:1sand) Sand cast iron including carriage of material in all leads and lifts.

Providing and fixing plastic seat (Solid/Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers:- Solid type white plastic seat and cover including carriage of material in all leads and lifts.

Providing and fixing vitreous china wash basin with single/double holes for pillar tap with C.I. or M.S. brackets painted white including holes and making good the same but excluding fittings confirming to BIS specification including carriage of material in all leads and lifts:- Circular 460mm dia (countertop)

Providing and fixing M.I. union for wash basin or sink 32mm dia confirming to BIS specification including carriage of material in all leads and lifs.

Providing and fixing C.P. brass waste for wash basin or sink 32mm dia confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6 mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of material in all leads and lifts confirming to BIS specification.

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.I. brass screws, including carriage of material in all leads and lifts. 600x20mm

Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of material in all leads and lifts confirming to BIS specification.

Providing and fixing bath shower rose with 15mm or 20mm in let :- 100mm dia., confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing C.P. brass bib tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P. brass bib tap (Superior or heavy type) including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia long body.

Providing and fixing C.P. brass pillar tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P. stop cocks confirming to BIS specification including carriage of material in all leads and lifts:- 15mm dia.

Providing and fixing PVC connection pipe with brass union 45 cm length 15mm nominal bore including carriage of material in all leads and lifts confirming to BIS specification.

Providing and fixing brass full way valve with wheel confirming to BIS specification including carriage of material in all leads and lifts:-

15mm nominal size

20mm nominal size.

Providing and fixing G.I./M.I. unions of following sizes(where not included in the item) including carriage of material in all leads and lifts confirming to BIS specification:-

15mm nominal size

20mm nominal size.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts:- 1000 litres net capacity

Providing and fixing stainless steel grating 100mm confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing PTMT jet spray of approved quality and colour with 1.5 mtr. Tube including carriage of material in all leads and lifts.

Providing and fixing P.V.C. plastic waste pipe for wash basin or sink of following size BIS specification including carriage of material in all leads and lifts.32mm mm dia.

Providing and fixing sand cast/cast iron spun spigot and socket soil waste and ventilating pipes (lead caulked joints to be measured and paid for separately)confirming to BIS specification including carriage of material in all leads and lifts:-

75mm nominal bore.

100mm nominal bore.

Providing and fixing ISI marked sand cast iron/cast iron spun fittings and accessories:- (a) Bends of required degree (any radius) with oval access door insertion rubber washer 3mm thick bolts and nuts complete including carriage of material in all leads and lifts:-

75mm nominal size

100mm nominal size.

Plain Bend:-

75mm nominal size.

100mm nominal size.

Single equal branch of required degree with oval access door insertion rubber washers 3mm thick bolts and nuts complete confirming to BIS specification including carriage of material in all leads and lifts:-

75mm nominal size

100mm nominal size.

Collars:-

75mm nominal size

100mm nominal size.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the walls and floors complete. 110mm x 75mm including carriage of material in all leads and lifts.

Providing lead caulked joint to sand cast iron/cast (spun) iron pipes and fittings including testing of joints including carriage of material in all leads and lifts:-

75mm nominal size

100mm nominal size.

Providing and fixing high density polyethylene / poly propylene 10 litres apacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts..

Arvind Kumar Sareen

Neeraj Kumar