ADDN/ALTN OF BLDG NO. P-34, MT OFFICE, PROVN OF SHELVES WITH SHUTTER P-1 BLDG AND SPECIAL REPAIR TO MES INSTALLATION AT GANDHINAGAR UNDER GE (AF) CHILODA

Amount

Dismantling of floor, hearth or wall tiling, etc. including cement Mortar bedding (but not backing) and removing debris, etc. to outside MD/AF Land, complete all as specified and as directed.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling/removal of existing water proofing membrane of any description and removal of material out of MOD land/sites etc complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 sqm but n exc 4.00 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n.exc 1.5 sqm each complete all as specified and directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation, for laying of HT cable etc and getting out in soft/loose soil complete all as specified and as directed.

M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified and as directed.

Removing excavated material n exc 50m and depoting where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M & L cement concrete 1:4:8 of type D2 (using 40mm graded stone aggregate) as in filling and mass concrete complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M & L for Reinforced cement concrete1:2:4 type B1 (using 20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M & L for Reinforced cement concrete1:2:4 type B1 (using 20mm graded aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M & L for formwork to sides and soffits of floor or roof beam, rough finished of flat concrete surface including suppots, overhangs etc complete all as specified and as directed.

M & L for Reinforced cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in Roof Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for fromwork to flat rough finished surfaces of concrete sunpended slab not exc 200mm thick horizontal or sloping complete all as specified and directed.

M&L providing reinforced cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate as in roof slabs supported on walls surfaces of concrete flat complete all as specified and directed.

M&L providing reinforced cement concrete type B1 (1:2:4) using 20 mm graeded stone aggregate as in chajja complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia over cut to length, bent to shape required including cranking, bending, hooking ends & binding with mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia over cut to length, bent to shape required including cranking, bending, hooking ends & binding with mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

All as per item No 28 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Pre-cast cement concrete block masonry with solid blocks, PCC 1:3:6 typeC1 (20mm graded aggregate exc. 10 cm in width and setting in mortar 1:6, complete all as specified and as directed.

M&L rendering 15mm thick in cement plaster 1:4 on surfaces fair faces of brick work and surface mixing with WPC as per Manufactures instruction, finished even and fair without using extra cement complete all as specified and as diected. Note : WPC shall be measured and paid separately.

M&L rendering 12mm thick in cement plaster 1:6 on fair faces of brick work and surface finished even and fair complete all as specified and directed.

M&L rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of roof slab, mixing with WPC, to receive tiles etc on vertical surfaces of wall as per Manufactures instruction complete all as specified and as diected.

M&L rendering 5mm thick in CM 1:4 on ceiling of concrete surfaces and complete all as specified and directed.

S&F fibre glass mesh 145 Gsm as in various column/beam joints before plaster work with necessary fitting and fixtures complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

M & L for newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M & L for complete removal of existing treatment of ceiling and applying three coats of white wash complete all as specified and as directed.

Material & Labour for preparing new Plastered Surfaces of Walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Camouflage pattern) with silicon additives @ 1.43 litre/ 10 sqm, over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Material & Labour for complete removal of existing treatment of Walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Camouflage pattern) with silicon additives @ 1.43 litre/ 10 sqm, over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M&L for Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed.

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

M&L complete removal existing wall surface applying two coats of oil bound distemper over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

Earth filling under floor including spreading, levelling, watering and well ramming in layers n exc. 25cm thick complete all as specified and as directed.

M&L for hardcore using broken stone or boulders nexc 63mm deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100mm thick cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L 40mm thick Cement Concrete 1:2:4 type B-0, using 12.5mm graded aggregate) as in floor complete all as specified and directed.

Providng and laying Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular), Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, set and Jointed in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4 complete all as specified and directed.

M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting,etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, complete all as specified and as directed.

M&L Non-skid Glazed Ceramic Coloured/Printed Tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc.6.0 to 7.0mm thick in Flooring, set and jointed in Neat Cement Slurry and pointed in White/Coloured Cement, laid over and including 15mm thick Screed Bed in Cement Mortar 1:4, complete all as specified and as directed.

M&L Coloured Glazed Ceramic Tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 15mm thick rendering as Screed or backing coat of wall tile in Cement Mortar 1:4, complete all as specified and as directed.

M&L for preapring clean and dried plaster surface and applying a coat of oil based bitumen primer confirming to (IS: 3384) at the rate of 0.30 litrs per Sqm and then laying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with non woven polyster reniforced membrane having thermal insulation with mineral gravel on upper side of membrane land on primed surface by torch application method complete all as specified and directed.

M & L for 75mm thic cement concrete type C1 1:3:6 (20mm garded stone aggregate) as in plinth protection complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M & L 25 mm sand filling under floors or in foundation, and sand filling in trenches as cable protection incl watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Area not exceeding 2.00 sqm each complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.

S&F factory made single extruded WPC (wood polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65x125mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonet and natural fibre (wood powder/rick husk wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed screw SS crews having minimum frame density of 750kg/Cum, screw withdrawl strength of 2200N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in postion with MS hold fast/lugs /SS dash fasterners of required dia and length complete as per direction of Engineer-in-charge. (Note : MS hold fast/lugsof SS dash fastenrers shall be paid for seprartely).

Providing and fixing factory made single extruded WPC (wood polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K valure 58-60 (Suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650kg/cum and screw withdrawl strength of 1800N (Face) & 900 N (Edge), minimum compressive strength of 50N/mm2, modules of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamindated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as per direction of Engnieer in Charge.

S&F Brass 2 lever Mortice lock, vertical type, size 65mm complete all as specified and directed.

S&F Brass handles, cast type, polished bright 150mm long, complete all as specified and directed.

S&F 150mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed, complete all as specified and directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Sheet Glass 5.5mm thick, Ordinary quality and glazing with Oil Putty in Square exc. 0.50 Sqm in Each Pane of Steel Windows, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.71mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram , complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and as directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles With Semi perforated 12mm thick micro tegular edged GRG false ceiling tilesof Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including screed bed 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F Table top wash basin of size 650x380x110mm catmax snow white colour including all fittings complete all as specified and directed. Make : CERA Cat No.- S2020159 or techno commercially equivalent as approved by GE.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F PVC (SWR) bends any 75mm bore complete all as specified and as directed

S & F PVC (SWR) bends any 110mm bore complete all as specified and as directed

S & F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply and fixing 15 mm outer dia UPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and directed.

All as per item No 77 here in before but 20 mm bore tube

S&F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specifeid and as directed.

S & F CP pillar cock mixer 2-in-1 for wash basin complete with all fittings complete all as specified and directed. (Make- CERA Cat No.F2007461 or techno commercially equivalent as approved by GE.)

S&F floor mounted, one piece water closet (western toilet), white (including seat cover, inlet and outlet rubber gasket, 'S' trap of size 690x370x645mm including fixing complete all as specified and directed by Engr-in-charge.

S & F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S & F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

S&F rotational moulded polethylene water tank of 500 ltrs capacity ( cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I complete all as specified and as directed.

S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod and high denty plastic ball screwed for iron pipe and fixed (min wt. 210gms) complete all as specified and as directed.

S&F Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Looking Mirror 5.0mm thick of size 600x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror and Fixed-in-repairs, complete all as specified and as directed.

S&F in repairs 20 mm brass chromium plateds towel rail of 20mm dia and 600mm in length 'D' shaped between flanges complete all as specified and as directed.

S&F PVC Connection Pipe 15mm size and 60 Cm in length with Adopter Nuts of PVC and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Waste Pipe 32mm dia (bore) having 35 inches long and fixed complete all as specified and as directed.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Cutting chases, pinning in, making good to facings in brick work where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and as directed.

S&F Zebra roller Blinds (horizontal) alongwith necessary fitting and fixtures for window for light filtering, privacy, UV protection Corded rolled up curtain window of any shade complete all as specified and as directed by Engr-in-Charge.

M&L Brick work with fly ash brick, old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick work or concrete surfaces of walls finished even & smooth with out using extra cement complete all as specified and directed.

M&L for 5 mm thick cement plaster in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L preparing new surface of wall and applying three coat of white wash complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying three coat of white wash complete all as specified and directed.

M&L ATT Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&LTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS-15658-2006 of 80mm thickness M-40 grade complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil complete all as specified and directed.

M&L PCC 1:2:4 type C2 (using 40mm graded crushed stone agg) as in foundation of posts and struts complete all as specified and directed.

S&F Mild steel works for posts and struts in fencing incl cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iorn fillets (for securing wire mesh etc) incl all necessary drilling , bolting or welding / riveting, etc and similar work conforming to Fe-290 Gde -E-165 complete all as specified and directed.

S&F mild steel screw bolts with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut , but length of bolt exc 5 cm and n exc 10 cm long and diameter of neck 10 mm complete all as specified and directed.

Supply only Chain Link Fencing MS galvanised fencing any size or type

Fixing only Chain Link Fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc. including provision of binding wire

S&F 10mm dia MS round bar for fixing of chain link fencing with posts complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling Plain or corrugated steel/ Fibre translucent sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded complete all as specified and as directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W (Gde E- 250) quality A complete all as specified and directed.

S&F pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 MPA as in roof covering fixed with self topping screw complete all as specified and directed.

M&L Preparing new steel surfaces exceeding 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for Preparing old painted steel surfaces exceeding 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

S&F factory made single extruded WPC (wood polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonet and natural fibre (wood powder/rick husk wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed screw SS crews having minimum frame density of 750kg/Cum, screw withdrawl strength of 2200N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in postion with MS hold fast/lugs /SS dash fasterners of required dia and length complete as per direction of Engineer-in-charge. (Note : MS hold fast/lugs of SS dash fastenrers shall be paid for seprartely).

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-290, (Gde E- 165) complete all as specified and directed.

S&F 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F Steel rolling shutters, thickness of laiths 1.25mm with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: gear operated type with bevel gear box and crank handle complete all as specified and directed.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for rendering in CM (1:3) 10mm thick over RCC roof, chajja/ brick wall mixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement complete all as specified and directed. Note - WPC shall be measured and paid separately.

S&F Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and Fixed-in-repairs, complete all as specified and directed.

S & F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC Waste Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps,waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F in repair Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Long Body with Capstan Head, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S & F in rapair Pillar taps, cast copper alloy, with capstan heads, chromium plated, facny type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair Stop Cock 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with long Shank and Cup (Concealed type), screwed down, high pressure, with Crutch or Butter-fly Handle, screwed Both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F in repair PVC Waste Pipe 32mm dia (bore) having 600mm long and fixed complete to Walls, Ceilings or in Floors, etc. complete all as specified and as directed.

S&F in repair Rotational moulded polye thylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore, including cleaning for refixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing and connections 20mm bore, including cleaning for refixing or removal to store, complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 with all necessary fittings on walls/ceiling of 20mm dia complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 with all necessary fittings fittings in trenches 25mm dia complete all as specified and as directed.

Demolition & breaking up Drain Pipe 100mm dia (Salt Glazed Ware, AC or Reinforced Concrete) set in Cement Mortar, complete all as specified and as directed.

M & L preparing new surface of wall and applying two coat of oil emulsion distemper over a coat of chalk whiting complete all as specified and as directed.

M&L for rendering 10mm thick plaster in CM 1:6 on other than fair faces of brick work, followed by 5mm thick plaster in CM 1:4 with water proofing compound @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and as directed. (Note : water proofing compound shall be measured & paid for separately).

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed.

Supply only integral water proofing compound

M&L for 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and as directed.

M&L for dark shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc. complete all as specified and as directed.

All as per item No 143 here in before but on vertical surfaces/skirting.

S&F Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S&F aluminum anodized barrel tower bolt of extruded section, length of bolt 200mm complete all as specified and as directed.

S&F 150mm size aluminum handles, cast type anodised complete all as specified and as directed.

S&F aluminum alloy, anodized, sliding door bolt of length 250mm with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm length complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for partitions, doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer-in-charge.

M&L PCC 1:3:6 type C2 (using 40mm graded crushed stone agg) as in foundation of posts and struts complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and as directed.

S&F 12mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and as directed.

S & F Continuous (piano) hinges, width of flap (when open) 30mm mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F 100mm Hasp and staple, aluminium anodiesed, safety type stove enamalled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F 75mm size Extruded brass handles, fabricated type polished complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm single core PVC insulated unsheathed multi stranded copper conductor FRLSH cable 1100V grade drawn through and incl PVC concelled conduit with accessories like bends tees, junction boxes etc fixed recessed in wall or ceiling etc including 1.5 Sqmm single core PVC insulated but unsheathed multistrandard copper conductor FRLSH cable 1100V grade as earth continuity wire incl modular sunken type pressed steel terminal boxes of size with 3mm thick bakelite steel white/coloured top cover for the following :- (a) One light point controlled by one switch complete

All as per item No 160 here in before but One fan point controlled by one switch complete.

All as per item No 160 here in before but One 3 pin socket out let 5 Amps on the independent board.

All as per item No 160 here in before but One 3 Pin socket out let 5 Amps on the same board.

All as per item No 160 here in before but with cable of size 2.5 Sq mm PVC insulated on independent board for power plug 15 Amps.

Supply and fixing Modular switch one way 6A,1 Module, complete all as specified and directed.

Supply and fixing Modular switch one way 16A,1 Module, complete all as specified and directed.

Supply and fixing Modular socket 6/10A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular socket 16/15A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular Fan Regulator, 120W, 2 module complete all as specified and directed.

Supply & fix ceiling rose 3 terminal/ poly carbonate, isolated body complete all as specified and directed.

Supplying and fixing of sheet metal enclosure, single phase, double door SPN DB 8 way, flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links ( without MCB's) SPN/ TPN complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing 240 Volts 10 KA 'Ç' Curve MCB SPN 4 pole of 40 Amp capacity complete all as specified and directed.

Supply & fix MCB SP 6 to 32 Amps 10 KA 240 V, 10 KA 'Ç' Curve complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including conencting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fittings 1 x 10 watt bulkhead luminaires including LED light driver holder conencting up with three core flexible copper cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 HZ, Size 300 mm complete all as specified and directed. Note :- (a) Making hole in existing brick/PCC wall of required size to accommodate exhaust fan and fixing louvers on outer surface shall be deemed to be inclusive of quoted rate by the contractor.

Supply & fix ceiling fans complete with blades, down rods as per site requirement , and accessories, 1 Phase, 230 V, 50 Hz, AC, 1200 mm sweep. Min air delivery 210 CFM with brushless direct current motor (BLDC, including down rod, Nut,Bolt,Clamp, hold fastener) complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified and directed.

M&L for brick protection cover to underground cable with sub-class ‘B’ old size over burnt bricks laid dry and flat across the axis of cable, abutting each other with gaps between adjacent bricks not exceeding 10mm complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6mm thick burried directly in ground not less that 2.25 m deep below normal ground level and top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI strip of size 25 x 4 mm by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical palte No 3 connected to earthing test point incl excavation, earth work in any type of soil strata, PCC chamber, 40 mm dia GI med grade pipe as protection of strip and 15 mm dia GI Med grade watering pipe, funnel, wire mesh etc including testing on completion complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, required length 3 run of 1.5 Sqmm PVC FRLSH copper multistranded conductor for conenction from connector of exhaust fan to ceiling rose, wall fastner etc complete all as specified and directed. Note :- (a) Making hole in existing brick/PCC wall of required size to accommodate exhaust fan and fixing louvers on outer surface shall be deemed to be inclusive of quoted rate by the contractor.

Abhishek Enterprises (BID ID -3453587)

ARTI CONSTRUCTION (BID ID -3453348)

ALBA AC AND REF SERVICES (BID ID -3453287)

Shree Builders (BID ID -3453047)

Haritwal traders (BID ID -3453536)

Priya Construction co. (BID ID -3453075)

Ramdev and Sons (BID ID -3453369)