Fire Fighting System for Adivasi Sanskrutik Bhavan at Ahwa, Dist. Dang.

Fire Fighting System for Adivasi Sanskrutik Bhavan at Ahwa, Dist. Dang.

Bill of Quantities.

(A) Percrentage Rate Tender ( Up to INR 50 cr.)

Quantities Rate In

Item estimated but figure

Descripction of Item Unit Amount

No. may be more or

1 Supply. installation, testing & commissioning of ISI 1.00 No 98432.58

approved electrical motor driven jockey pump set

having 10.8 m3/hr. @ 70m head. The pump unit shall

be a horizontally direct mounted motor. Unit shall

comprise the following minimum requirements: a)

Pump, b) Electric motor IE2, c) Foundation bolts, d)

Mating flanges with gasket and fasteners, e)

Discharge gauges, etc. complete in all respect, with

2 Supply, installation, testing & commissioning of 1.00 No 25678.24

Priming tank, HDPE type, 1000 litres, with necessary

piping 100 mm size, G.I pipe for priming the pumps,

pipe of with butterfly valves for isolation, Water Filling

to priming tank by piping min. 50 mm size, with all

3 Supply, installation, testing & commissioning of 1.00 No 55635.85

Manifold( surge vessel,)for fire hydrant system, min.

300 mm diameter, made from M.S plate, hydro tested

to 15 kg./cm2. with ball valves, header with couplings

for fitting pressure switches, pressure gauges etc.with

necessary isolation valves with all complete.

4 Supply, fabrication & erection of aboveground G.I. 'C'- 13.00 Mtr 642.36

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 50 mm dia.

5 Supply, fabrication & erection of aboveground G.I. 'C'- 21.00 Mtr 1177.66

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 80 mm dia.

6 Supply, fabrication & erection of aboveground G.I. 'C'- 65.00 Mtr 1690.74

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 100 mm dia.

7 Supply, fabrication & erection of aboveground G.I. 'C'- 210.00 Mtr 2525.00

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 150 mm dia.

8 Supply, installtion, testing & commissioing of 30.00 Mtr 3047.17

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. &

above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x

mm thick, wrapping & coating with 13KV holiday

testing . Rates shall include sand bedding of 75mm

dia all around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc. 10 % of

all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the

"Field Joints". Hydrostatic testing for 2 hours at 150%

of the system pressure, hook-up etc., complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. (Road Crossing) 150 mm dia.

9 Design, Supply and installation of Safety Signage 9600.00 Sq. 10.10

made of Zinc Sulphilde based glow in dark , Rigid inch

sheet with High Luminous property enclosed in a

transperent weather proof UV stabilized plastic pasted

on 3 mm thick clear acrylic sheet such as EXITS,

EMERGENCY EXIT, DO NOT USE LIFT DURING

FIRE, FLOOR MARKINGS, FIRE LIFT, STAIRCASE

EXIT, FIRE ALARM CALL POINT, FIRE HOSE REEL,

FIRE HYDRANT POINT etc.

10 Supply, installation, testing & commissioning of 3.00 No 2824.97

pressure switch. (Range 0 to 16 kg/cm2)

11 Supply, installation, testing & commissioning of 150 8.00 No 2739.12

mm dia. dial Burdon Type Glycerine Filled pressure

gauge with isolation ball valve arrangements with

necessary isolation valves with all complete.( Range

12 Supply, installation, testing & commissioning of Cast 1.00 No 5906.48

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating

flanges, drilling as per IS/ANSI 150# with mating

flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 50 mm dia.

13 Supply, installation, testing & commissioning of Cast 1.00 No 8183.02

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating

flanges, drilling as per IS/ANSI 150# with mating

flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 80 mm dia.

14 Supply, installation, testing & commissioning of Cast 1.00 No 10271.70

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating

flanges, drilling as per IS/ANSI 150# with mating

flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 100 mm dia.

15 Supply, installation, testing & commissioning of Cast 1.00 No 15920.63

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating

flanges, drilling as per IS/ANSI 150# with mating

flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 150 mm dia.

16 Supply, Installation, Testing & Commissioning of Cast 4.00 No 2011.92

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 50 mm dia.

17 Supply, Installation, Testing & Commissioning of Cast 4.00 No 2568.43

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 80 mm dia.

18 Supply, Installation, Testing & Commissioning of Cast 4.00 No 3124.94

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 100 mm dia.

19 Supply, Installation, Testing & Commissioning of Cast 4.00 No 4494.50

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 150 mm dia.

20 Supply, installation, testing & commissioning of Cast 3.00 No 1541.26

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with

all complete Accessories 50 mm dia.

21 Supply, installation, testing & commissioning of Cast 3.00 No 2226.04

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with

all complete Accessories 80 mm dia.

22 Supply, installation, testing & commissioning of Cast 3.00 No 3167.36

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with

all complete Accessories 100 mm dia.

23 Supply, installation, testing & commissioning of Cast 3.00 No 5820.63

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with

all complete Accessories 150 mm dia.

24 Supply, installation, testing & commissioning of SG 3.00 No 1113.02

iron body SinglePlate Wafer Type NRV conf. to

ASTMA 536, PN-1.6 complete with mating Flanges

class # 150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete. Accessories 50 mm dia.

25 Supply, installation, testing & commissioning of SG 3.00 No 1455.41

iron body SinglePlate Wafer Type NRV conf. to

ASTMA 536, PN-1.6 complete with mating Flanges

class # 150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete. Accessories 80 mm dia.

26 Supply, installation, testing & commissioning of SG 3.00 No 1797.80

iron body SinglePlate Wafer Type NRV conf. to

ASTMA 536, PN-1.6 complete with mating Flanges

class # 150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete. Accessories 100 mm dia.

27 Supply, installation, testing & commissioning of Y 2.00 No 5564.09

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 80 mm dia.

28 Supply, installation, testing & commissioning of Y 2.00 No 7276.04

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 100 mm dia.

29 Supply, installation, testing & commissioning of Y 2.00 No 11555.41

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 150 mm dia.

30 Supply, installing, testing and commissioning of 1.00 No 4194.53

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary

complete accessories. 80 mm dia.

31 Supply, installing, testing and commissioning of 1.00 No 6163.02

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary

complete accessories. 100 mm dia.

32 Supply, installing, testing and commissioning of 1.00 No 12411.89

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary

complete accessories. 150 mm dia.

33 Supply, installation, testing & commissioning of Four 1.00 No 8987.99

way fire brigade Inlet connection with 63 mm dia.

stainless steel (SS304) instantaneous male inlets with

built in non return valve in each inlet with 150 mm dia.

header pipe, suitable rubber cap and GI chain

including nuts, bolts, washers, gasket 3 mm thick, etc.

with all complete.

34 Supplying FIRE bucket round bottom of 9 liters 20.00 No 1027.17

capacity made out of 24 gauge G.I Sheet with extra

handle at bottom duly painted white inside and Red

out side with FIRE mark. Filled with dry-sand and kept

on existing stand provided or hung on wall hook.

35 Supplying and erecting floor mounting Stand for 5.00 No 5564.09

keeping four nos. of FIRE buckets comprising

mm in length, 900 mm height frame made out of

30mm x 30 mm x 4 mm angle iron with cross supports

legs, welded with 4 hooks and duly painted with one

coat of primer and two coats of approved enamel P O

36 Supply & installation of stainless steel body Orifice 15.00 No 1070.60

Plate of suitable inner bore along with matching flange

- as per specification & requirement as per hydraulic

37 Providing and fixing approved make Perforated C type 30.00 Mtr 471.67

cable tray. Made from pre- galvanized sheet steel.

The cable tray should be bended as per IS 2062/1079

. with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc.

erected on existing support as per Specification and

as per instruction of engineer in charge..(5) 300 X

38 Providing and fixing approved make Perforated C type 30.00 Mtr 322.19

cable tray. Made from pre- galvanized sheet steel.

The cable tray should be bended as per IS 2062/1079

. with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc.

erected on existing support as per Specification and

as per instruction of engineer in charge..(3) 150 X

39 Supply, installation, testing & commissioning of 15.00 No 5435.82

Oblique pattern type stainless steel (SS 304) single

headed External Fire Hydrant Valve with 63 mm dia.

female instantaneous outlet conf. to IS: 5290, type - A,

including mating flanges, galvanised nuts, galvanised

bolts/studs, washers & gaskets 3 mm thick with all

40 Supply, installation, testing & commissioning of 63 mm 15.00 No 1755.38

dia. stainless steel (SS 304) Universal Branch Pipe

41 Supply & installation, testing & commissioing of Fire 15.00 No 6967.99

Fighting Hose - conf. to IS : 636, type B (type- 3), The

fire hose shall be 15 m long with 63 mm dia. stainless

steel (SS 304) couplings conf. to IS: 903, at both the

ends for connection with the hydrant valve and the

42 Supply, installation, testing & commissioning of 15.00 No 2525.00

fabricated from 3 mm MS sheet, hose box of size-450

mm x 600 mm x 250 mm - painted with Fire Red as

per IS: 5, shade no. 536 front 3 mm thick transparent

glass with lock & key, handle and brass hinges - to

accommodate one number of 15 mtr long hose and

one number of universal branch pipe, including

supporting arrangement with civil work.

43 Supply, Installation, testing & commissioing of 15.00 No 7404.31

Swinging type mild steel hose reel drum with 20 mm

dia. x 30 mtr. rubber hose as per IS: 884. The

mounting stand shall be of mild steel and the hose

shall be fitted with a SS shut-off nozzle & SS ball valve

of 25 mm dia. including supporting arrangement with

all complete. accessories

44 Supplying, fixing & testing of of CI ball Valve 25mm 20.00 No 707.00

45 Supplying, fixing & testing of New Battery of diesel 1.00 No 15834.78

engine 150 Amp.

46 Supply and installation of Diesel Tank For Diesel 1.00 No 16691.26

Engine With All Accessories 100 Ltrs.

47 Supplying, filling & testing lube oil for diesel engine 40.00 Ltrs 321.18

48 Supply and commissioning of Oil Filter. 1.00 No 707.00

49 Supplying, filling of diesel in diesel engine tank 100.00 Ltrs 89.89

50 Supply and commissioning of Diesel Filter 1.00 No 428.24

51 Supplying, filling & testing coolant to engine cooling for 20.00 Ltrs 240.38

52 Excavation for foundation upto 1.5 m depth including 12.00 Cu. 125.86

sorting out and stacking of useful materials and Mtr

disposing off the excavated stuff upto 50 Meter

lead.(A) Danse & Hard soil

53 Filling Of Gaps Between pipe and Core Cutting Hole 55.00 No 299.97

With Chemical and Cement

54 Steel work, welded in built up sections framed work 400.00 Kg 91.00

including cutting, hoisting, fixing in position and

applying a priming coat of read lead paint & two coat

oil paint. (A)In beams and joists, channels angles

Tees, flats, with connecting plates or angle cleats as

in main and cross beams. Hip and jack rafters, purlins

conneted to common rafters and the like.

55 Supplying & erecting XLPE(IS:7098)(I)-88 ISI 100.00 Mtr 136.35

unarmoured copper cable 1.1 KV grade to be erected

as directed of following size. (E) 3 core 2.5 Sq. mm

for pressure switch

56 Providing and erecting XLPE(IS:7098)(I)-88 ISI 90.00 Mtr 285.83

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(B) 3 core 4 Sq. mm

57 Providing and erecting XLPE(IS:7098)(I)-88 ISI 100.00 Mtr 497.93

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(D) 3 core 10 Sq. mm (Only Fire Panel to Fire Pump)

58 Providing and erecting XLPE(IS:7098)(I)-88 ISI 75.00 Mtr 213.11

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable for Diesel Engine Battery

Charger (A) 3 core 2.5Sq. mm

59 Supply, Filling and Fixing of approved make ABC type 15.00 No 1969.50

fire extinguisher - 6 Kg. Capacity as per IS:15683 &

60 Supply, Filling and Fixing of approved make CO2 type 15.00 No 5521.67

fire extinguisher. Capacity 4.5 Kg. (conforming to IS-

61 Supply, Filling and Fixing of approved make ABC 4.00 No 3423.90

Moduler type automatic fire extinguisher. Capacity

Kg. (conforming to IS-15683).

62 Submitting the application to obtain Fire Plan Approval 1.00 No 252500.00

and After Completion of Work Obtain Final Fire NOC

63 Supply, Installation and commissioning of Air Release 5.00 No 1412.99

Valve, 25 mm Dia. connection.

64 Supply, Installation and commissioning of Fire Alarm 2.00 No 21398.87

Panel Conventional type, 4 zone, with complete

65 Supply, Installation and commissioning of smoke 300.00 No 1027.17

detectors / heat detectors, with complete accessories.

66 Supply, Installation and commissioning of plug in base 300.00 No 257.55

for the smoke detectors, hooters, with complete

67 Supply, Installation and commissioning of Audio 10.00 No 1070.60

hooters , with complete accessories.

68 Supply, Installation and commissioning of Manual Call 10.00 No 1010.00

Points, with complete accessories.

69 Providing and erecting XLPE(IS:7098)(I)-88 ISI 2500.00 Mtr 176.75

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A)

core 2.5 Sq. mm for Fire Alarm System

70 Core cutting in wall and in RCC slab with size as 15.00 No 342.39

below: 50 mm dia. Hole

71 Core cutting in wall and in RCC slab with size as 7.00 No 428.24

below: 80 mm dia. Hole

72 Core cutting in wall and in RCC slab with size as 20.00 No 514.09

below: 100 mm dia. Hole

73 Core cutting in wall and in RCC slab with size as 8.00 No 599.94

below: 150 mm dia. Hole

74 Core cutting in wall and in RCC slab with size as 5.00 No 856.48

below: 200 mm dia. Hole

75 Supply, installation, testing & commissioning of ISI 1.00 Set 204996.67

approved electrical motor operated Kirloskar make fire

hydrant main pump set horizontal end suction back

pull out top discharge centrifugal fire pump set with all

the standard acessories, base frame, coupling, and

foundation bolts with following specifications

Model -DB 80/26,

Flow-137 m3/hr,

Motor Rating -45KW/60HP/3 ph

Suc x Del - 100 x

76 Supplying, Installation, Testing and commissioning of 1.00 Set 447653.21

Kirloskar make diesel engine driven fire hydrant pump

set suitable for automatic operation and consisting of

following: horizontal type, centrifugal end suction back

pull out, top discharge pump of cast iron body &

bronze impeller with m.s.fabricated common base

plate, coupling, coupling guard, foundation bolts

etc.,as required.

Flow-137 m3/hr,

Engine - 62 HP / 3 ph

Suc x Del - 125 x

77 Fire Hydrant Panel suitable for 10 hp Jockey pump, 60 1.00 No 101000.00

hp (137 m3/hr @ 70 m head) main electrical pump

and 62 hp (137 m3/hr @ 70 m head) Diesel engine

R Y B Indication - 1 Set

VAF Digital Meter - 1 Set

F1 60 HP Star Delta Starter - 1 For Main pump

F2 10 HP DOL Starter - 1 For Jockey Pump

F3 Auto - On / Off Diesel Pump With Battery Charger

Control Circuit With Auto - Manual On/Off

On/Off Trip Indication

On/Off Push Button

Dully Powder Coated PO Red Colour,

Fabricated From 14/16 SWG,GI Sheet , IP-42

Protection,-Fixed Type Floor Mounted

Cable Entry : Bottom

78 Pay Legal Fees to Concern Authority for Obtaining 2300.00 Sq.mt 15.15

Plan Approval and Final NOC

Net Total Amount =

Net Total Amount =

I we am / are willing to carry out the work at …................................ % above/ Below percent ( Should Be writen in

figures And words) of the estimated rate mentioned above. Amount of my / our tender works out as under.

Estimated Amount Put to tender. Estimated Amount Put to tender

Deduct…........ % Below Deduct…........ % Below

In Words In Words

(1) The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

(2) The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

(3) GST and Income tax TDS will be deducted at a source while making payments of bills

(4) In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as

per actual mix design the cost of difference of cement consumption have been deducted from the rate of original item at

the rate of input rate mentioned in all the tender.

Signature of Bidder

Divisional Accountant Executive Engineer,

Dang ( R&B) Division, Dang ( R&B) Division,