ELECTRIFICATION WORKS OF HAPPINESS PARK AND TAKE A BREAK IN PATHANAMTHITTA MUNICIPALITY

Amount

ELECTRIFICATION

Supply, installation, testing and commissioning of Outdoor Wall Mounting Cubical Type KSEBL Metering Panel with Double Door and Canopy suitable for 415 V, Three Phase,4 Wire 50Hz AC supply system having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame works and covers, 2 mm thick for gland plates, cleaning and finishing complete with 7 tank process for Powder Coating in approved shade and then provided with Clear Coating, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 12 mm x 3 mm at the rear with 2 Nos. earth stud and control wiring with 2.5 / 1.5 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables, cable alleys etc. complete as required. The panel shall conform to the Electrical Inspectorate and KSEBL standards and it shall only be manufactured after getting approval from the Engineer-in-charge and the Consultant BUSBAR-1 Runs of 63 mm x 10 mm Aluminium for each Phase ,I Runs of 63 mm x 6 mm Aluminium for Neutral INCOMER 1 Nos - l00A/125A 4P Switch Disconnector OUTGOING - I Nos - Provision for Fixing Three Phase Energy Meter, I Nos - 63A Bakelite Fuse Units with HRC Fuse of Suitable Rating, 1 Nos - 63A Neutral Link , 1 Nos - 40A/63A 10kA 4P C Curve MCB. OUTGOING - 2 I Nos - Provision for Fixing Single Phase Energy Meter, 1 Nos - 63A Bakelite Fuse Units with HRC Fuse of Suitable Rating, 1 Nos - 63A Neutral Link ,I Nos - 40A/63A 10kA DP C Curve MCB, There shall be Separate Compartment for Energy Meter and Fuse Units/Neutral Link with KSEBL Sealing Provision. There scope also includes providing Connections From Energy Meter to Fuse Units/Neutral Link and then to MCB using 4.0/6.0 Sq.mm FRLS (Flame Retardent Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC Insulated single core copper conductor cables with necessary copper sockets (banana/palm/pin/ring) including crimping etc. complete as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthins etc. as required. (But without MCBIRCCBA/ isolator l2 way. Double door

Supplying and fixing following rating, double pole,240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, double pole, (single phase and neutral),24O volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections. testing and commissioning etc. as required.Single pole

Supplying and fixing 5 amps to 32 amps rating,240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

Supply and laying of XLPE insulated and PVC sheathed armoured Aluminium power cable of 1.1 kV grade of the following sizes in the existing excavated trenches, built up trenches and pulling through existing pipes including all minor civil works etc. complete as required 3.5 Core 50 Sq.mm

Supply and laying of XLPE insulated and PVC sheathed armoured Aluminium power cable of I .l kV grade of the following sizes in the existing excavated trenches, built up trenches and pulling through existing pipes including all minor civil works etc. complete as required 4 Core l0 Sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV Grade as required.3 1/2 X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV srade as required.4 X 10 sq. mm (25mm)

Supply and providing gland earthing using Gland Earthing Clips / Clamp for following size of PVC insulated and PVC sheathed /XLPE Aluminium conductor cable of l.l kV grade etc. complete as required 3 1/2 X 50 Sq.mm

Supply and providing gland earthing using Gland Earthing Clips / Clamps for following size of PVC insulated and PVC sheathed / XLPE Aluminium conductor cable of 1.1 kV etc. complete as required 4 X 10 Sq.mm

Wiring for light poinV fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface Casing Cap with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. complete as required Group C

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

Supplying and fixing following sizel modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (l00mmx75mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate& switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

Supplying and fixing of following sizes of Casing Cap along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed installation etc. complete as required 11/2 lnch

Supplying and fixing of following sizes of Casing Cap along with accessories in surface/ recess including cuffing the wall and making good the same in case of recessed installation etc. complete as required 2 lnch

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steeV PVC conduit as required.3 x 2.5 sq. mm

Supply and laying of 1.5 Sq.mm 1.1 kV Grade Three Core Round Insulated Copper Conductor and Sheathed Flexible cable with compact construction and high insulation resistance. The cable shall have the specifications of Standard FRLS PVC lnsulation, FRLS Sheathing in accordance with IS 694, BS 6500,IEC 60227, DIN VDE-0281, IEC 60754-I IEC, 60332-I, BS 4066-I, ASTMD 2843, ASTMD 2863, Conductor Class 5, Number of Conductor Strands 30, Nominal Diameter of Conductor Strands 0.25mm, Nominal Thickness of Insulation 0.6mm, Nominal Thickness of Sheath 0.9mm, Approximate Overall Diameter 8.2mm, AC Current Rating of 18A, Voltage Drop/Amp/Metre for Single Phase AC 31mV, Maximum Conductor Resistance at 20 Dee.C 13.3 Ohms/Km etc. complete as required

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, singlecoie cable in the existing surface / recessed steeV PVC conduit as required. 3 X 1.5 sq.mm

Supply & installation of light fittings on TW round block Supply, conveyance installation testing and commissioning the light fittings of foliowing types made of CRCA with 0.5mm thickness complete with all accessories and lamps-etc. directly on wall or ceiling with PVC round block neatly painted to suit the fitting and giving connection with required length of l6/0.20mm 3 core copper conductoi flex wire conforming to relevant ISS and giving connections as required.1200 mm 1X20W LED Lamp with box type fixture

Supplying and fixing PVC batten/ angle holder including connection etc. as requhed.

Supply and fixing of LED Bulb up to and including l2W in the existing PVC batten / angle holder etc. complete as required

Supply, installation, testing and commissioning 50W, 240V,50H2,400mm Sweep Wall Fan with 3 blades, Air delivery of 72 m3/min, Noise level of 62dB to 63.5d8, Rated speed of 1350/1360 Revolution per minute, adjustable upward and downward tilt mechanism, Thermal Overload Protector (TOP), pull cord, using mounting accessories and Stainless Steel bolts, nuts, round and spring washers or screws etc. complete as required

Charges for cutting holes suitable for accommodating exhaust fans above 305mm sweep and up to 450mm sweep includine plasterine colour washine etc. as required.

Supply, installation, testing and commissioning 90W ,220 V to 240 V, 50H2,300mm sweep Heavy Duty Metal Exhaust Fan with rated current of 0.43, air delivery of 1710 m3/hour, noise level of 50 to 55 dB, rated speed of 1400 revolution per minute etc. in the existing holes using necessary Stainless Steel bolts, nuts, round and spring washers or screws and giving connections with required length of 2410.20mm 3 core copper conductor flex wire conforming to relevant IS or extending the original wiring etc. complete as required

Excavation of all types of soils for the laying of PVC insulated and PVC sheathed / XLPE Aluminium or Copper conductor cable, GI / DWC HDPE / RCC /PYC / Conduit Pipes, Earthing conductors to the required width and depth up to and including l.2m and back filling etc. complete as required. (The trench dimensions and specifications shall conform to CPWD / PWD, Electrical Inspectorate and KSEBL Standards)

Supplying, laying and jointing of the following sizes of double wall comrgated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench 50/38 mm or nearest size

Earthing with CI / GI earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long with charcoal / coke and salt etc. complete as required

Supply and laying of the earthing conductors of the following sizes in existing earth excavated or built up trenches, clamping in trays, walls, racks, risers, trusses etc. using heavy duty Aluminium or GI flats of which spacing between 35cm to 65cm without making holes in the earthing conductor and pulling through pipes including all minor civil works, including connection / terminating with welding or existing Stainless Steel bolts, nuts, round and spring washers after painting / treatment process as per Electrical Inspectorate standards etc. complete as required 25 X 3 mm GI Strip

Supply and drawing bare earthing conductors of the following sizes along with wirine/ cables and siving connection as required 4.06 mm GI conductor (8 SWG)

Supply and drawing bare earthing conductors of the following sizes along with wirinl cables and giving connection as required 3.15 mm copper conductor ( 10 SWG)

Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.l5 mm (10 SWG)

Reinstallation of already dismantled High Mast using Octagonal Pole made single/two sections of hot dip galvanised GI sheet 100mm top diameter, 360mm boffom diameter thickness 3mm mm suitable for wind speed as per IS 875 Part III with head frame assembly two point suspension system with steel wire rope 5mm dia double drum winching system and including round arm galvanized luminary carriage suitable to install 6/8 Nos luminaries in symmetrical arrangement control gear box and lighting spikes with single phase operation power tool installed inside the base compartment including connector foundation bolt 4 Nos fixed in existing RCC foundation and junction box etc. complete as required 12 Meters

Supply installation testing and commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70 mm top diameter, 130 mm bottom diameter thickness 3mm 6ase plate dimensions of 200x200x16 mm suitable for wind speed as pel IS 875 Part III single arm bracket 0.5mt including connector foundation bolt 4 noi fixed in existins RCC foundation and iunction box etc. complete 8 Meters

Supply, installation, testing and commissioning of Decorative Casting with Amount Decorative Double Arms and also including 2 Nos of 50W Warm Colour Output including connector, foundation bolt if necessary and with existing RCC foundation and junction box etc. complete as required 3 Meter

Supply, installation, testing and commissioning of Decorative Casting with 134943.30 Decorative Top Single Arm and also including I Nos of 50W Warm Colour Output including connector, foundation bolt if necessary and with existing RCC foundation and junction box etc. complete as required 3 Meter

Supply Conveyance, installation, testing and commissioning of 200W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled,/Nichea with power factor greater than 0.95 at fulI load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

Supply, installation, testing and commissioning of 200W LED street light output greater than l05lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 kV and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than l0 %, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230V AC supply. Driver compartment should be separately accessible for maintenance (LN{79 and 80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

Supply Conveyance, installation, testing and commissioning of l00W LED street light output greater than lO5lumenAV 4000-6000 K with IP 66 protection LED Chip make Cree,{LumilledA.,lichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230Y AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

Preparation and submission of application for Single Phase Connection along with drawings, detailed load schedule etc. and co-ordination with KSEBL for energization etc. complete as required. (*All Statutory fees shall be remitted by the Client / Consumer or it shall be reimbursed on the submission of supportins documents)

CIVIL FOUNDATION WORKS

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

Providing and laying in position cement concrete of specif,red grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 eraded stone aggresate 40 nominal size)

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of srade Fe-500D or more

Providing and laying in position specified grade of reinforced cement concrete, cost of centering, shuttering, finishing and reinforcement - All work up :1:2:4 ( I cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidated each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

EXCLUSIVE OF GST

MERKURY ELECTRICAL CORPORATION (BID ID -2343726)