SPECIAL REPAIR TO OFFR GOVT MD ACCN BLDG NO P-12/02 (MAJ ACCN) AT DHOLEWAL MIL COMPLEX UNDER GE LUDHIANA

Amount

Sch 'A' sec-I

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level).

Demolition of reinforcement cement concrete as in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work (reinforcement cut as reqd to facilitate demolition).

M&L for reinforced Cement Concrete type B1 1:2:4 (nominal mix ) (using 20 mm graded stone aggregate) in Chajjas etc.

M&L for use and waste rough finished flat Form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc.

M&L for use and waste rough finished Form work to edges of concrete floor and roofs and similar work exceeding 5 Cm but not exceeding 10 Cm wide.

S&F for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing, serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for vitrified ceramic dark shade coloured tiles 8-10mm thick square/rectungular polished area of each tile not exceeding o.36 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm thick screed bed of cm 1:6 complete all as secified.

Ditto- as per item No 8 above but as in skirting over rendering 10mm thick in cement mortar 1:4.

M&L for non skid cerermic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc. 0.11 sqm but n.exc. 0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6).

Ditto- as per item No 10 above but as in skirting over rendering 10mm thick in cement mortar 1:4.

M&L for glazed ceramic coloured/ printed tiles 450mm x 300mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:3) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick Cement concrete 1:2:4 type B-0 using 20 mm graded stone aggr.as in sub flooring rough finished surface complete all as spd and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete.

M&L for granite slab (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick screed bed of cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite.

M & L for machine cut kota stone slab 20 to 25 mm thick as in flooring / stair case landing, laid over & incl. 15mm thick cement screed base in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as spd.

Ditto as per item No 16 above but in one piece as in treads of stair

M&L for machine cut kota stone slab 20-25mm thick as in skirting/steps of stair case laid over & incl.10mm thick cement screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as spd.

Demolition of brickwork built in cement or cement lime mortar incl all quoins, arches, pillars, etc but excl ashlar facings, dressed stonework and precast concrete articles.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cm 1:6 all as specified.

-ditto- but except bricks

S & F for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises gauged skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note: wire mesh and painting shall be measured & paid separately under appropriate item.

All as per item No 22 here in before but window with glazed shutters . Note Glass and painted shall be measured and paid separately under appropriate item.

S&F for mild steel framed work such as guard bars/grills,grating etc with end of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chromate primer complete all as specified.

S&F for galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tined tacks.

S&F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sqm each panes complete all as specified.

Taking down chowkats or frames(without taking off shutters from the frame) area n.exc 1.5 Sqm each.

Taking down chowkats or frames exc 1.5 Sqm but n.exc 4.0 Sqm with shutters (without taking off shutters from the frame).

Taking down shutters of any desciption area exc 1.0 Sqm but n.exc 2.0 Sqm each and refixing in the same opening after easing and minor adjustment.

S&F for pressed steel frames,size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified.

Ditto but size 125 X 60mm

M&L for providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats.

S&F for 35mm thick factory made 2nd class hard wood plain, framed, panelled shutters (two panels) with lock rail and panelsof 9mm thick BWP commercial; ply or 12mm thick veneered p article boards on both sides. The size of rail and style as per IS-1003 (part-I) kiln seasoned and chemicaly pressure treated.

M&L for 35mm thick IInd class Hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.(without sash bars) edges of framing plain, chemfered fitted with cut and mitred beads for securing glass, etc. sizes of shutters as specified in SSR Part I section 8, clause 8.24 (a) supplied and fitted to chowkat.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain glover PVC sheet reinforced with MS square tube in opening as per specification and drawing.

S&F for factory made soilid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F for mild steel 300mm helical door spring , ordinary rat tail rod patteren including roller and roller plate complete.

S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F for 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F for 125mm aluminium handles, cast type ,anodised and pattern/design as approved.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store.'

-ditto- all as per item No 41 above but 20mm bore.

S&F for 15mm GI tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

-ditto all as per item No 43 above but 20mm bore.

Refixing old steel tubing and connections in new or old postion (wall, ceiling , floors ,etc) 15mm bore.

-ditto all as per item No 45 above but 20mm bore.

S&F in repairs ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore pipe.

S&F for stop valves 20mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle etc complete fixed in repairs.

S&F in repairs Rotational moulded polythylene water strarge tanks 500 ltr (Cylinderical vertical with closed top ) hoisted and fiexed in position all as per specified in SSR Pt-1.

S&F in repairs Rotational moulded polythylene water strarge tanks 1000 ltr (Cylinderical vertical with closed top ) hoisted and fiexed in position all as per specified in SSR Pt-1.

S&F in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed (Make : Hinduware/Cera or equvalent approved by Engineerin-Charge.

S&F in repair plastic water closet seat cover of White colour closed pattern with flat bottom and cover with mild steel chromium plated hinging device etc complete as specified and directed.

S&F in repair vitreous china washbasin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end complete all as specified (without pedestal).

S&F in repair vitreous china washbasin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed including pedastal for washbasin complete all as specified.

S&F for viterous china squartting pan orrisa pattern , size 580x 440mm white, interged foot rest including connection to trap and to flush pipe, anti syphonic pipe etc complete making good to floor.

M&L for 75mm dia cast iron floor trap with grating incl jointing to waste pipe with run lead joint and embedde in cement concrete (1:2:4) type B0-1 using graded stoe agg complete all as specified and directed by Engineer-in-Charge

S&F for cast copper alloy chromium plated fancy type single lever basin mixer.

S&F for pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F for bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F for C P health faucet suitable for Europian western commode (EWC) including PVC connection 15mm size with PTMT nuts and washer, of length 900mm.

S&F for soap dish fixed to walls with chromium plated brass screws.

S&F for stop valves/angle valve 15mm, chromium plated,fancy type, complete fixed in repairs.

S&F for PVC connections 15mm size with PTMT nuts of legth 600mm.

S&F for toilet paper holder of CP fixed to walls with chromium plated brass screws.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia D-type, 60cm long between flange.

S&F in repairs brass chromium plated tubular towel rack.

S&F for brass CP mixer/Mixing valve on walls for mixing hot & cold water screwed down for iron pipe , including two-in-one joints to steel pipes or unions and plugging and screwing to walls and fixed 15mm bore fixed in repairs comlete all as specified.

S&F in repair PVC bathroom cabinet mirror size 350mm x 450mm complate all as specified and directed.

S&F for chlorium plated shower roses with or without swivel join ts 125mm size incl fixing to steel pipe in repairs.

S&F for 10 ltr capacity PVC valveless, syphonic action type flushing cistern,low level, white, with inlet, ball valve, float and handle incl brackets fixed inrepairs.

M&L for two coat of white wash to old surfaces of walls after preparation

Ditto all as per item No 71 above but on ceiling surfaces

S&F for 25 mm thick flush shutter solid core construction, with block board core and plywood face panels,commercials type on both sides covered with decorative face venner with lipping/frame to math complete all as specified.

S&F in repairs stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen or laboratory, with plug, waste pipe, washers incl. cantiliver cast iron brackets, connecting union etc overall size 915mm X 460mm with bowl size 410mm X 330mm X 160mm.

S&F in repairs pre-laminated (both sides) particle board 18/19mm thick with decorative choice laminations, interior grade, fixed with screws to timber frame work.

S & F for aluminium handle cast type anodised of size 75mm completed all as specified and directed.

Taking down curtain rod along with wooden pallmate laid on wall complete all as specified and directed by Engineer-in-Charge.

S&F in repair curtain rod made out of 25mm dia(outer dia )pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and directed, Make :- Aerolux/MEC.

S&F for plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed.

S&F for mild steel prepainted bracket to hold the curtain rod and fixed to wall (Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and directed.

Demolition and breaking up drain pipes/pipe fixed to wall (PVC, Salt glazed ware, AC or re-inforced concrete) set in cement mortar bore of pipe 100mm all as directed.

S&F for 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

S&F for 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

S&F for PVC (SWR) bend any radius 110mm bore complete all as specified and directed.

S&F for PVC (SWR) 'P' trap radius 110mm bore complete all as specified and directed.

M&L for endura chequered cement concrete tiles 30cmx 30cmx 10mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 20mm thick screed in cement mortar 1:6.

Demolition for cement conc exc 15cm thickness but above ground floor as sunken floor .

M&L for cement concrete type E - 2, 1:5:10 (using 40 mm graded stone aggregate) as in sunken flooring.

M&L for applying two coats of SHALIMAR SUPERCRETE/NITOBOND water proofing coating on the entire surface of sunken portion all as specified .

M&L for 15mm thick cement screed in CM 1:3 admixed with integrd water proofing compound FOSROC’s complast X 421 IC @ 130ml per bag of cement incl a bonding coat of FOSROC”s Nito bond AR cement slurry/STP NO 1 liquid @ 200ml per bag of complete all as specified.

M&L for PCC (1;2:4) type B-1 using 20mm graded stone agregete as in sides of rounded or chamfered on edges of sunken floor

M&L for stainless steel plate rack of superior quality size 36" x 24" with not less than 8 kg all as specified .

S&F for steel ventilators fixed type with glazing bar complete.

S&F for floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long.

Dismantling brick tiles or terracing tiles sinlge layer on roofs.

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part there of)

M&L for wire brushing neat cement slurry with 3kg of cement per sqm at top and bottom of base coat and cleaning top surface all as specified

M &L for PCC 1:2:4 type B-1 as roof padding concrete to bring the extg slab in slope of 1:40. complete all as specified.

M&L for priming surfaces and applying normal treatment (for moderate conditions) using bitumen primer @ .30 Kg/Sqm applied hot.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2kg per sq.m incl cleaning surfaces.

M&L for fixing APP based polymeric membrane minimum weighing 3kg/sqm and min 3mm thick reinforced with polyster non woven fabric (wt not less than 150gms/sqm) land on primered surface by torced application.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% 0f crude oil by weight of cement

-ditto- all as per item No 102 but but except tiles after clening and removing old mortar from bricks.

M&L for flush pointing to brick laid flat or brick tiles in paving cement mortar in 1:3.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc.

M&L for 12mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:6.

M&L for 5mm thick plastering on fair faces ofr cone surfaces finished even and smooth w/o using extra cement in cm1:3 on ceiling .

M&L for 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth w/o using extra cement in cm1:4.

M&L for preparing of new surface of plaster and applying three coats of white wash on ceiling.

M&L for Preparing of new plastered surface and applying two coats cement base paints on walls.

M&L for Preparation of new surface of wall and applying two coat of oil emulsion white or printed on walls over 3mm thick Birla wall care putty filling on plastering surface .

M&L for preparation of old surfaces of wallsand applying one coat of cement base paint complete all as specified.

M&L for complete removal of existing treatment and applying two coats of oil bound emulsion white or printed on walls. over 3mm thick Birla wall care putty including preparation of surfaces of wall.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of new surfaces of wood surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of pink primer.

M&L for preparation of old painted Steel surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

-do- all as per item no 117 above but two coats of synthetic enamelled paint of new surface of steel.

M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement morte 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. (note: wlded mesh to be paid separately)

Resecuring or easing and adjustment without taking down the shutters of any description exc 1 Sq.m and n.exc 2 Sq.m each complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing and adjustment without taking down the shutters of any description exc 2 Sq.m each complete all as specified and as directed by the Engineer-in-Charge.

S&F for framed work as in doors or gate,coolers stand of angle or others section etc confirming to Fe 410-s .

S&F for chromium plated sink mixture(single liver) of size (254mmx203.2mmx203.2mm) incl fixing to steel pipe in repairs (Make-CERA CAT Part No-F1005501)

S&F for chromium plated two way bib cock (single knob) of size (254mmx203.2mmx203.2mm) incl fixing to steel pipe in repairs (Make-CERA CAT Part No-F1015163)

S&F for butt hinges 100mm long extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed , type B-21 complete all as specified.

Taking down carefully the point wiring (light, Fan, socket or power) complete, (incl fittings such as switches, sockets any type, ceiling roses, pandents, light fittings, etc for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down Ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Refixing only ceiling fan and connecting up including provision sutiable of new down rod for ceiling fans,of cable from celling rose/ connector to fan incl painting all as specified and as directed.

M &L for point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps etc complete concealed in walls(on surface in ceiling/beam etc.) including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor, all as specified and as directed for the following :-

One light/fan/call bell point controlled by one, one way switch

One switch socket outlet point 5 Amps on independent board

One 3 Pin socket outlet , 5 Amps on the same board with other switch

One light point controlled by two 2-way switches, with cables 1.5 sq. mm size

All as per item No. 129 described here-in-before but with copper conductor cable FR LS 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board complete all as specified and directed.

Supply and fix for wall decorative LED light fittings 10watt higher energy saving decorative LED lighting fixture enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix for LED tube light fittings 1200 mm, 20W, 240V, 50Hz,rated input current- 0.070-0.110, rated input watt 20, oprating voltage range- 140-270, P.F- not less then 0.95, surge protection upto- 4Kv, IP20, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix for LED tube light fittings 600 mm, 10W, 240V, 50Hz,rated input current- 0.070-0.110, rated input watt 20, oprating voltage range- 140-270, P.F- not less then 0.95, surge protection upto- 4Kv, IP20, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

Supply & fix for exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and as directed.

M & L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed . Note:- Three run of wire shall be measured in one unit.

M & L for sub main wiring complete with 2 runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed .

Supply and fix for sheet metal enclosure with socket plug top and MCB single pole and neutral enclosure with a two pin and earth plug and socket complete with double pole MCB complete all as specified

Supply and fix for TPN MCB DB 4 ways ,Double door with 415 Amps, Double door type complete all as specified and as directed .

Supply and fix for MCB TPN 63 Amp, 415 Volt , C- series, 50 Hz, breking capacity-10 kA complete all as specified and as directed .

Supply and fix for SPN MCB DB 12 ways with 200 Amps rated bus bar 240Volt, Double door type all as specified

Supply and fixing for MCB SPN 40 Amps 240 V, C- curve, 50 Hz, breking capacity-10 kA. complete all as specified and directed.

Supply and fixing for MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breking capacity-10 kA . complete all as specified and directed

Supply and fix for ceiling rose surface type bakelite 65 x 50mm with three terminals complete all as specified and as directed

S&F for switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F for switch Modular 16A single pole, one way, 1 module complete all as specified and as directed

S&F for socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F for socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F for modular White cover plate with frame,12 module complete all as specified and as directed

S&F for modular White cover plate with frame,8 module complete all as specified and as directed

S&F for modular White cover plate with frame,4 module complete all as specified and as directed

S&F for modular White cover plate with frame,3 module complete all as specified and as directed.

S&F for modular White cover plate with frame,2 module complete all as specified and as directed.

S&F for modular Metal flush box 12 module complete all as specified and as directed

S&F for modular Metal flush box 8 module complete all as specified and as directed.

S&F for modular Metal flush box 4 module complete all as specified and as directed

S&F for modular Metal flush box 3 module complete all as specified and as directed

S&F for modular Metal flush box 2 module complete all as specified and as directed

S&F for switch Modular 6A single pole,two way, 1 module complete all as specified and as directed

S&F for calling bell , AC, 230 Volts, single pole complete all as specified and as directed.

Supply and fix for fan step regulator, 120W 2 module complete all as specified and as directed.

Taking down of XLPE cable any size complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete all as directed & specified

Returning filling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete all as specified and as directed

Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed. Note:- 18 cm punned down thick shall be considerd for mesurement.

M & L for old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified

Taking down of any size of bldy security light fittings complete all as specified and directed.

Supply and fixing for bldg security light fitting LED 30 W LED made up of pressure die cast aluminium housing with potted isolated driver and high power LED and indl lenses, oprating range- 90V to 340V AC. LED life -1 Lac burning hrs , fixture should with stand 320V upto 48 Hrs , auto cut off>320 V & restart ,440V sustain upto 8 Hrs, NABL acreddited LM 79 report, IP66 with high power LED lamp incl with suitable size of bracket compete all as specified and directed.

M& L for earthing complete for LT Panels with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically at a depth not less than 2.25 metres below normal ground level with top edge of the plate at a depth not less than 1.5 metres below normal ground level, connected with and including GI strip 32mm x 6mm and including GI pipe 50mm bore light grade as protection pipe (from top of earth plate up to the test point) by means of GI bolts, nuts, check nuts and washers of GI and thimbles, earth plate surrounded by packed layers of charcoal dust and common salt 15cm thick, all around including top and bottom and watering pipe 20mm bore of GI pipe medium grade with funnel and wire mesh, PCC chamber of size 300x300x300mm(top of chamber minimum 15 cm above the normal ground level (1:3:6) using 20mm graded stone aggregate and RCC cover (1:2:4) type B-I using 20mm graded crushed stone aggregate of 25mm thick with 2 nos MS handles of 12mm dia including necessary excavation/ earth work in any type of soil and as shown in Electrical plate No. 3 of SSR Part-I (2009) testing on completion complete all as specified.

GURPARTAP SINGH GULATI

ANUJ ABROL CONTRACTOR

PK ENTERPRISES