SPECIAL REPAIRS TO BLDG NO B-06 AND NC-01 (TYPE-II and TYPE-III) BLOCK AND D-06 (TYPE-IV) BLOCKS, BLDGS OF RESIDENTIAL AREA AT DEAL UNDER GE (I) RnD DEHRADUN

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge complete all as specified and directed

M&L for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each coloured tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including for Screed bed (or) bedding layer of mortar 15mm thick for laying floor finishes CM (1:6) complete all as specified and directed.

Demolishing cement concrete nominal 1:3:6 of richer mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Demolishing cement concrete nominal 1:4:8 of leaner mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Material and labour for cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete all as specified and directed .

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection even and smooth without using extra cement complete all as specified and directed.

Material & labour of PCC 1:3:6 type C-2 using 20 mm graded stone aggregate (4 stay). in mass concrete and filling complete for foundation/hard standing coping , complete all as specified and directed.

Providing and laying 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing complete all as specified and directed

M&L for providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints of depth 10mm complete all as specified and directed

M&L for PCC 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) as in sub base of floor complete all as specified and directed

Taking down ceiling fan / Exhaust fan by disconnecting the electric connection and dismantling the blades and removing from ceiling or wall of bldg by descrewing the nut bolt and complete all as specified and directed.

Taking down existing energy meters with meter box of any type any capacity, keeping aside safely & refixing/connecting the same in its original position after making complete of point wiring/sub main wiring of bldg/Qtr complete all as specified and directed by Engr-In-Charge. Note:- Small items required for fixing the electric energy meter with meter box at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.

Rehanging and refixing ceiling fan/ exhaust fan and connecting up including provision of PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50 Sqmm from ceiling rose or connector block of fan including minor repairs such as replacement of locking pin, reel insulators, bolts, nuts etc and spraying one coat of synthetic enamel paint of color approved by GE/ Engr in charge all as required and complete all as specified and directed.

M&L for 12 mm thick cement plaster finished with a floating coat of neat cement of mix in 1:3 (1 cement: 3 fine sand) complete all as specified and directed

All as per iterm Ser No. (2) above but except bricks complete all as specified and directed.

All as per iterm Ser No. (15) above but as in skirting/dados etc. complete all as specified and directed.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to I

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete all as specified and directed.

S: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed

M&L for 20-25mm thick kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete all as specified and directed

Providing and laying Polished Granite stone slab colour of Black, cherry/rubby Red or equivelent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes etc. including removing cable protection covers/ bricks complete all as specified and directed. Notes : (i) Excavation shall be made carefully in order to avoid damage of existing cables and brick protection.

15 mm cement plaster on Brick / concrete surface of wall / ceilling of mix :1:6 (1 Cement : 6 Sand) surface making even and smooth without using extra cement complete all as specified and directed.

Providing and fixing 10 mm thick acid and/alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, In flooring over and including a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) complete all as specified and directed

M&L for chequerred precast cement concrete tiles 22 mm thick medium shade pigment using 50% white cement 50% Grey cement in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) complete all as specified and directed

Weberdry PUR Basic shall conforms to: Colour: Light grey; Product structure: polyurethane; recoat time: 12 hours to 18 hours; service temperature: -30 degrees to + 90 degrees. Elongation at breakage: > 600 %; Pack size: 25 Kg; Application Consumption: 1.2 to 2.0 Kg/ m2 (for 2 to 3 coats); Crack bridging ability: up to 2mm: Hardness (Shore A scale):65-70; Chemical properties: Good resistance against acidic and alkali solutions (5%), detergents, seawater, and oils. 1) Elongation : >600% as per ASTM D 412/ DIN 52455 2) Tensile Strength : 4 N/mm2 as per ASTM D 412/DIN 52455 3) Water vapor permeability: > 30 gr/m2/day ISO 9932:91 4) Crack bridging capability: up to 2 mm crack (reinforced) EOTA TR-008 5) Shock temperature (15 min): 200°C 6) Adhesion to concrete: >2,0 N/mm2 (concrete surface failure)- ASTM D 903 NOTE: - Application Brush / Roller recommended: (a medium nap 8-12 mm pile- paint roller is recommended) New rollers should be dampened with water before being used for the firsttime. For best results with a paint brush use a good quality, 50 mm long bristle variety. Protective Covering: - Weberdry PUA Seal is a single component liquid applied solvent free polyurethane based hybrid waterproofing membrane for indoor and outdoor use. • Solvent-free, non-toxic • Single component, ready-to-use • Highly flexible • High ability to bridge cracks • Excellent resistance to UV and rains Weberdry PUA Seal shall conform to: Colour: Elongation: >450% as per ASTM D 412/ DIN 2016. Tensile Strength : 1.25 N/mm2 as per ASTM D 412/DIN 52455 Water vapor permeability: > 25 gr/m2/day ISO 9932:91 Crack bridging capability: up to 1.5 mm crack (reinforced) EOTA TR-008 Shock temperature (15 min): 200°C Adhesion to concrete: >1.5 N/mm2 (concrete surface failure)- ASTM D 903.

Water proofing treatment on RCC roof slabs by Techno Commercial process :- (a) Surface Preparation: All surfaces shall be carefully prepared as it is essential for optimum finish and durability. The surface shall be made dry sound and free from all contaminates using mechanical tools like a grinding machine, chisels with hammers, and Rotatory grinded.Removing the existing brick bed cova by using concrete breaker / removing existng treatment up to the mother slab. RCC Mother Surfaces must be clean, even and sound concrete. Remove all oil, dirt, laitance, protrusions (by light grinding) and other contaminants manually to attain a fairly smooth surface. Even pneumatic acids can be used for the removal of algae formations.The surface shall be dry and the moisture content shall be less than 5%. (b) Crack treatment (Option 1): All cracks shall be treated using Weber SBR (SBR-based,multipurpose, concentrated, liquid polymer additive). Cut open the cracks by making a groove in the form of “V” shape at the required size. Clean the grooves and 25 mm minimum depth of the joint to make it free from all dirt, dust and other contaminants. Apply a mixed slurry coat of Weber SBR (1 part of SBR: 1.5 parts of cement: 0.5 parts of Water) by volume in and around the groove. Fill polymer modified mortar into the grooves using mix design (1part of SBR: 5 parts of cement: 15 parts of sand: 4 parts of water) as at dosage over the neattacky coat of Weber SBR. Finish the surface with neat steel trowel flush with the surface. Allow the applied mortar to cure and dry completely for min 7 days. Weber SBR shall confirm to: Appearance: White color liquid; Specific Gravity: 1.02 – 1.03; pH: 9 – 11; Solid content: 47%; Pot life:60 minutes; Re-coat time: 4-6 hours; Application consistency: brushable consistency.

Material & labour for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches/ducts for cable protection complete all as specified and directed. (NOTE : Thickness after punning shall be measured for payment)

M&L for two coat Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : On new plastered surface incl. preparing the surface smooth etc. with white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete all as specified and directed.

M&L for one coat Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : On Old work including removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. with white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete all as specified and directed.

Crack treatment (option 2): After surface preparation apply a uniformed leveled coat of PU sealant.(dispersion based single component ready to use sealant) Material shall be spread and levelled uniformly using spatula or any appropriate tools and allowed to dry completely. (c) Coving: Mix Weber SBR (SBR based, multipurpose, concentrated, liquid polymer additive) with water and cement (1 part of SBR: 1.5 parts of cement: 0.5 parts of Water) by volume toa thin slurry and spread the mix over the surface with brush (thickness not more than 1 mm). Over the tacky bonding slurry, install coving at horizontal and vertical corners using polymer modified using mix design (1 part of SBR: 5 parts of cement: 15 parts of sand: 4 parts of water) finishing in half round or fillet in shape. The applied plastered surface shall be allowed to cure for complete dry for 3 days.Weber SBR shall confirm to: Appearance: White colour liquid; Specific Gravity: 1.02 -1.03; pH: 9 – 11; Solid content: 47%; Pot life:60 minutes; Re-coat time: 4-6 hours; Application consistency: brushable consistency. (d) Bore Packing (Up to 100mm Dia): Providing and applying Weberprim epox 501-2 component Standard an epoxy bonding agent over the PVC and internal side of

concreteafter rubbing it with emery paper/sand paper. Later Filling the pipe gap with Weber NSG2from the top all over the periphery, with all shuttering already in place, . Leaving Top 20 mm. which shall be filled with Mortar. (e) Waterproofing coating: Weberprim epox 501: Over the prepared surface, apply a coat of Weberprim epox 501, two component High performance transparent epoxy based non- solvent universal waterproofing primer for both sealing and floor coating applications on absorbent and non-absorbent surfaces, by mechanical means, applying using brush/roller/Squeeze or other appropriate tools, Allow the surface to air cure for 5 to 6 hours before application of subsequent coat. Weberprim epox 501: Over the prepared surface, apply a coat of Weberprim epox 501, two component High performance transparent epoxy based non-solvent universal waterproofing primer for both sealing and floor coating applicationson absorbent and non-absorbent surfaces, by mechanical means, applying using brush/ roller/ Squeeze or other appropriate tools, Allow the surface to air cure for 5 to 6 hours before application of subsequent coat. Weberprim epox 501 shall conforms to: Colour: Transparent; Mix ration: 2: 1 (Epoxy based Resign: water-based Hardener); Adhesion to concrete: 1.5 Mpa (Concrete failure);Application temperature: 10 degrees to 40 degrees; Pot life: 60 Min; over coating time: 4 to 6 hours; Application thickness: 100 to 200 gm/ m2. Waterproof coating: Weberdry PUR Basic: -Elastomeric, single components, specially designed polyurethane-based cold liquid applied waterproofing membrane product shall bemixed uniformly before applying. Apply first coat and allow the surface to dry. During the application of the Second broadcast sufficient sand over the wet surface of Weberdry PUR Basic to provide mechanical bonding and allow it to dry completely as per the manufacturer's specification.

Sunken Treatment : M&L for cleaning the surface with wire brush to remove dirt, dust or any loosely held materials. All existing cracks must be opened up in V notch shape and filled with a mixture of cement mixed with 37 +/- 1% solid content Styrene Butadiene rubber based multipurpose polymer in a ratio of 3:1 or PU sealant making surface smooth and level wherever needed. Application by brush or roller a coat of a two component (1:1.4 ratio) polymer modified elastomeric cementitious waterproof membrane must have adhesion to concrete > 1 Mpa, fortified with graded fillers, polymers and additives applied seamless waterproofing coating at a specified coverage per kg to all required areas to achieve a thickness of 500 – 600 microns in one coat and allow the surface to dry for 4 -6 hours before 2nd coat and it should be covered by ready-to-use, fiber reinforced elastomeric, super flexible acrylic waterproof coating with More than 150% elongation confirms to ASTM D 412: 2016 and should contain solid contents of minimum 55 +/- %. Acrylic coating must be done with pre priming coat of acrylic waterproofing primer which contains 47 +/- 1% solid contents with recommended DFT of 30-40 microns complete all as specified and directed

M&L for Finishing walls with 100% Premium acrylic emulsion paint (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. on new / old plastered wall surfaces having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives complete all as specified and directed

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead complete all as specified and directed

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) complete all as specified and directed

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead of area 3 Sqm and below complte all as specified and directed.

Centring and shuttering including strutting,ropping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform complete all as specified and directed

Providing and fixing 30mm thick wire gauge shutters kiln seasoned and chemically treated hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, with ISI marked stainless steel butt hinges of required size and necessary screws complete all as specified and directed.

Thermo-Mechanically Treated cold twisted bars of grade Fe-500D reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level complete all as specified and directed

Dismantling doors, windows and clerestory windows of area 3.00 sqm and below (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead complete all as specified and directed

Dismantling wooden boardings 10mm to 25mm thic

kness in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead complete all as specified and directed

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete all as specified and directed

S&F 18mm to 20mm thick solid factory made PVC board for cup board /cabinate shutter with one side 1mm thick printed pvc sheet other side plain pvc sheet suitable fixed with &including suitable pvc frame, matching colured beading to cover all edges & screwed portion of frame, Magnetic catcher as per specification & drawing complete all as specified & directed.

M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete all as specified and directed

Providing and fixing of 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a PVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a PVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a PVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) complete all as specified and directed

Providing and fixing for Powder coated aluminium (minimum thickness of powder coating 50 micron) shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) complete all as specified and directed

Providing and fixing double strip (horizontal type) magnetic catcher of approved quality in cupboard/word robe shutters, including fixing with necessary screw etc complete. Double strip (horizontal type) complete all as specified and directed

Providing and fixing stainless steel 35mm soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete all as specified and directed

S&F Chromium plated stailess steel wire basket (cutlery basket ) pull out type , size 480x500x100mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed.

S&F Chromium plated stailess steel wire Bottle pull out basket (storage basket ) pull out type , size 100x150x750mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed.

S&F Chromium plated stailess steel wire Thali basket (storage basket ) pull out type , size 480x150x200mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed.

S&F Chromium plated stailess steel wire saucer basket (storage basket ) pull out type , size 480x500x150mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed.

S&F Auto closing hinges 35mm of 8 crank for kitchen cabinet shutter fixtures and complete all as specified and directed

M&L for Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture complete all as specified and directed.

S&F Auto closing hinges 35mm of 120 crank for kitchen cabinet shutter fixtures and complete all as specified and directed

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete all as specified and directed

Per 100 RM

S&F Stainless steel handles 150mm size for kitchen cabinet shutters and complete all as specified and directed

Providing and fixing M.S. Piano hinges ISI marked IS: 3818 (overall width 35 mm) finished with nickel chromium plating grade I as per IS: 1068 and fixing with necessary screws etc complete all as specified and directed overall width 35mm

Dismantling of tile work of any thickness upto 25mm in floors and roofs laid in cement mortar including stacking material within 50 metres lead complete all as specified and directed

Providing and laying vitrified floor tiles in different size of tiles 600x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc, complete all as specified and directed.

M/L for one or more coat painting on old wood surfaces with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade complete all as specified and directed

Providing and fixing ISI marked 100x58x1.90 mm M.S. pressed butt hinges bright finished with necessary screws etc. complete all as specified and directed

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm complete all as specified and directed

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm complete all as specified and directed

S&F 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and directed

Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 115mm size complete all as specified and directed

Providing and fixing chromium plated brass 100 mm mortice latch and door lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete all as specified and directed

Providing and fixing factory made uPVC R4 series white colour sliding glazed three track window upto 1.80 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 115 x 45 mm & sash 44 x 55 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension complete all as specified and directed

Providing and fixing factory made uPVC white colour casement/fixed window double panels with fixed mullion with SS 304 friction hinges as per size and weight of sash and multi point locking system, zinc ally (zamak) powder coated handles, using R2 series co

mprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 39 x 39 mm, sash 39 x 60 mm & mullion 39 x 60 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Height of window upto 1.20 sqm) complete all as specified and directed

M&L for fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading complete all as specified and directed

M&L for second class soft-wood wrought timber scantlings in framed work and fixed with cleats etc. complete all as specified and directed.

M&L for two coat of synthetic varnishing over a prime coat including preparation of new wood surfaces of any description, over 10cm in width or girth including wood filler liquid transparents complete all as specified and directed.

M&L for one coat of synthetic varnishing including preparation of old wood surfaces of any description, over 10cm in width or girth complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips etc complete all as specified and directed.

Providing and fixing 4mm thick glazing with float glass panes (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) complete all as specified and directed

Providing and fixing 12 mm thick prelaminated particle board with decorative laminatiion on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings complete all as specified and directed

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment complete all as specified and directed

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. (Only weight of grill to be measured for payment).

Dismantling timber scantlings in framed work 40 sq. cm and over in section, in any position complete all as specified and directed

Providing and laying Vitrified tiles in different size of tiles 600x600 (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete all as specified and directed

S&F for 4.8 mm thick,Sheet glass,ordinary quality and glazing with beading (any type) or oil putty in square exc 0.5 sq. m in each pane, etc complete all as specified and directed

Dismantling old plaster/grit wash with clean water or skirting raking out joints and cleaning the

S&F 4.0mm thick figured glass, pin head type and glazing with beading (any type) or oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed

Dismantling old plaster/grit wash with clean water or skirting raking out joints and cleaning the

Dismantling of 75 to 80mm dia C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed

Dismantling of 100mm dia C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter complete all as specified and directed

Providing and fixing 110x110x110 single tee with door on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed

All as per item ser No. (87) above but single bend of 110mm dia complete all as specified and directed.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever require, White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer complete all as speciied and directed.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead complete all as specified and directed

Providing and fixing CP brass toilet paper holder complete all as specified and directed.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as specified and directed

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete all as specified and directed

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture complete all as specified and directed

surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed

Dismantling water tanks and removing to store capacity exc. 250 ltr but not exceedings 500 liters complete all as specified and directed.

M&L for one or more coat of painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old steel surface complete all as specified and directed

S&F 15mm brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for wall mixer complete all as specified and directed

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) for nternal Work- Exposed on wall complete all as specified and directed

M&L for 6mm plaster in CM 1:3 on ceiling surface/concrete surfaces complete all as specified and directed

Providing and fixing 15mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints including cutting chases and making good the walls etc. for concealed work complete all as specified and directed

Providing and fixing 20mm bore Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete all as specified and directed

S& F in repair soap dish, Stainless steel of approved pattern complete all as specified and directed.

Providing and placing on terrace (at all floor levels) 500 liters capacity polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and

making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete all as specified and directed

Providing & fixing in repairs White vitreous china water closet squatting pan (Indian type/Orissa pattern W.C Pan of size 580x440 mm) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge complete all as specified and directed.

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan complete all as specified and directed.

S&F in repairs 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

Providing and fixing 25mm gun metal gate valve with C.I. wheel of approved quality (screwed end) complete all as specified and directed

S&F in repair 100 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) complete all as specified and directed.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 complete all as specified and directed

S&F in repair 15mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle chromium plated fancy type long shank and cup(concealed type), screwed both ends for iron pipe or for unions complete all as specified and directed

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter complete all as specified and directed

Providing and fixing 15mm bore, 450mm long uplasticised PVC connection pipe with brass unions complete all as specified and directed

Providing and fixing P.V.C. low level flusingh cistern 10 Ltr capacity (white) with manually controlled device (Handle lever) conforming to IS:7231, with all fittings and fixtures complete all as specifiend and directed.

S&F 600 mm long 20mm dia brass chromium plated tubular towel rails complete all as specified and directed.

Providing and fixing 15mm size C.P. brass angle valve (two/three way) for basin mixer, jet spray and geyser points etc. of approved quality conforming to IS:8931 complete all as specified and directed.

Providing and fixing 25mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete complete all as specified and directed.

Providing and fixing 15mm C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms complete all as specified and directed.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) floor trap with grating incl jointing with solvent cement complete all as specified and directed.

M&L for removing the plants/ vegetation from bldgs more than fifth story height including penetreated roots complete and injecting chemical GLYPHOSPHATW 41% SL 20 ml or till refusal by makimg cut/ injection in the stem of plant 30mm C/C spraying with solution (25ml Glyphospoto 41% diluted with one litre water) including necessary scaffolding etc wk will be carried out from bldgs more than 5th storey but upto 8th storey with and including dismantling of plain or corrugated steel sheeting, any gauge, thickness complete all as specified and directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, jafri wall etc. complete all as specified and directed.

Providing and fixing 200mm/250mm bright finished brass helical door spring (superior quality) any type, complete all as specified and directed.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge complete all as specified and directed.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete all as specified and directed.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces even and smooth without using extra cement with WPC. complete all as specified and directed (Note: Liquid type WPC shall be mixed as per manufacturer's instructions and measured/paid separately under relevant item).

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board 510x1040mm bowl depth 250mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed.

Providing and laying in position cement concrete of specified grade excluding the 1:2:4 (1: Cement, 2: Sand, 3: Concrete) cost of centering and shuttering - All work up to plinth level complete all as specified and directed.

S & F Stainless steel Plate rack of size 900mm x 600 mm x 200mm deep with plate racks, spoon holders, shelves etc complete all as specified and directed.

Providing precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) complete all as specified and directed.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete all as specified and directed.

Demolition and breaking up drain/rain water pipe of size 150mm dia, set in cement mortar or complete all as specified and directed.

Providing, laying and jointing glazed stoneware pipes 150 mm dia class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

S&F Providing and fixing 150 x 10mm size aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and directed.

M&L for providing and injecting chemical emulsionat points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

All as per item ser No.(60) above but size 75x47x1.70mm complete all as specified and directed

All as per item ser No. (63) above but size 150x10mm complete all as specified and directed

All as per item ser No. (64) above but size 100x10mm complete all as specified and directed

All as per item ser No. (85) above but 75mm dia complete all as specified and directed

All as per item ser No. (87) above but 75mm dia complete all as specified and directed

All as per item ser No. (101) above but for 25 mm bore tube complete all as specified and directed

Providing and laying factory made chamfered edge 60mm thick cement concrete paver blocks of approved colour and design, M-30 grade in footpath or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as specified and directed.

M&L for PCC 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) for coping of manholes, parapet walls etc complete all as specified and directed.

Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge complete all as specified and directed.

Providing and laying cement concrete bed 1:4:8, type D-2 to drain pipes of size 150mm dia including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Taking down of carefully unserviceable Aluminium/copper point wiring (light, fan socket or power) complete with fitting such as switches, ceiling rose lamp holder, sockets, fan regulators, SK/FTL light fittings etc removing materials for store for keeping in safe custody or for taking credit (credit for above items should be taken as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan point controlled by one Switch complete all as specified and directed.

S&F Modular switch piano single pole one way 6 amp complete all as specified and directed.

S&F Modular TV Co -axial socket 1 module with metal flush box and white Plate of 1 module complete all as specified and directed .

S&F Modular switch piano single pole one way 16 amp complete all as specified and directed.

S&F Modular switch , 6 amp, single pole, two way complete all as specified and directed.

S&F Modular bell push, 6 amp 240 volts complete all as specified and directed.

S&F in replacement of UNSV fluorescent tube light with Surface and wall Bright LINE IP 40 LED batten fitting 20 W, 220V, AC Durable extruded aluminum body with high quality PC diffuser for uniform illumination with high efficacy (>125 Lm/W),enhance efficiency connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-charge.

S&F in replacement of UNSV LED mirror light fitting with LED 10 watts, 1000 lumens 6500K comprises of aluminium extruded channel, frosted diffuser, integrated electronic driver, IP 20 protection and all accessories pre- wired including connecting to mains complete all as specified and directed.

S&F door bell, AC, 240 volts, single pole complete all as specified and directed.

S&F in replacement of UNSN Decorative, Wall mounting champagne gold finish fixture with Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base complete all as specified and directed.

S&F in replacement of UNSN Decorative, Round/ Square surface mounted LED Panel, of 24 W 6500K PDC aluminium housing and high translucent frosted Plastic diffuser robust Luminaire. Efficacy 100 lm/W complete all as specified and directed by Engineer-in-Charge.

Supply & fixing Inverter LED Lamp 9 watt 6000 K energy saving with cool day type complete all as specified and directed by Engr-in-Charge .

Supply & fixing of LED building light 35 Watt, are made of pressure die c

ast aluminium housing, with integrated lenses and High power LED's with IP 66 protection for better optics for uniform distribution and connection with three core copper flexiable cable 16/0.20 from ceiling rose to fitting with complete all as specified and directed .

S&F Modular socket outlet 2/3 pin combined 2 module 6/16 amp complete all as specified and directed.

S&F 32 mm dia GI light grade pipe bracket 1.50 m long bent to shape by cutting & welding as required & directed and fixed on wall with suitable size of FI clamps to be tightened with bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer complete all as specified and directed.

M&L in replacement UNSV of sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 25 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor complete all as specified and directed.

All as per item ser No. (106) above but 20mm dia complete all as specified and directed

Taking out existing cement concrete interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead complete all as specified and directed.

M&L in replacement UNSV of sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 4 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 20 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified and directed.

S&F in replecement of UNSV vertical type load line distribution board ,double door, 4 way, AC 3 Phase 415 volt with TPN bus bar 250 Amps for each phase with 2 Neutral bar, 2 Earthbar and cable ties for cable management,fully insulted busbar & shrouded Neural bars ,improved Pan assembly for each insullation ,prefitted masking sheeet,reversible door for IP 43-"IK 09 with metal door Suitable for provision for MCCB up to 125 A as incomer and SP/TP MCB's as out going complete all as specified and directed by Engr-in-Charge.

S&F Modular socket outlet 2/3 pin combined 2 module 6 amp complete all as specified and directed.

All as per Srl item No 145.00 above for point wiring for one light point controlled by two Nos two way switch complete all as specified and directed.

S&F in replecement of UNSV vertical type load line distribution board ,double door, 8 way, AC 3 Phase 415 volt with TPN bus bar 250 Amps for each phase with 2 Neutral bar, 2 Earthbar and cable ties for cable management,fully insulted busbar & shrouded Neural bars ,improved Pan assembly for each insullation ,prefitted masking sheeet,reversible door for IP 43-"IK 09 with metal door Suitable for provision for MCCB up to 250 A as incomer and SP/TP MCB's as out going complete all as specified and directed by Engr-in-Charge.

Supply and fixed in replacement of UNSV MCCB 4 pole,160 Amps 415 volts, 50 Hz adujustable type having breaking capacity 36 KA , with thermal magnetic protection complete all as specified and directed by Engineer-in-Charge

All as per Srl item No 145.00 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on same board with other switches complete all as specified and directed.

All as per Srl item No 145.00 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board complete all as specified and directed.

Supply and fixed in replacement of UNSV MCCB 4 pole,200 Amps 415 volts, 50 Hz adujustable type having breaking capacity 36 KA , with thermal magnetic protection complete all as specified and directed by Engineer-in-Charge

Supply and fixed in replacement of UNSV Isolator 4 pole, 100 Amps 415 volts, 50 Hz 'C' Curve having breaking capacity 10 KA , with thermal magnetic protection unit and testing Complete all as specified and directed.

S & F in replacement of unserviceable RCCB for earth Leakage protection DP , 30 mA, 240 volts 'C' Curve suitable for fixing in DB of capacity 25 Amps complete all as specified and directed.

S&F Angle holder, insulated polycabonate body with back plate suitable for batten fittings complete with One number LED lamp 9/10 Watt complete all as specified and directed.

S&F ceiling rose 3 plates polycarbonate, isolated body complete all as specified and directed.

S&F in replacement of UNSV bulkhead fitting with LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F modular fan step regulator 120 W 2 module complete all as specified and directed.

S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole and neutral MCB 20 amp,240Volts power coated CRCA steel sheet enclosure recess mounted with chained metal cover for the socket outlet with and including one number single pole 'C' series MCB 16-32 Amp as required complete all as specified and directed.

S & F in replacement of unserviceable MCB SP 240 volts 'C' Curve suitable for fixing in DB of capacity 6 to 32 Amps complete, all as specified

Taking down unserviceable existing water heater, keeping aside safely & refixing the same to its original position after servicing of the whole geyser/ making functional after completion of wiring work, complete all as specified and directed by Engr-in-charge.

S&F in replacement of UNSV MCB distribution board Double door, SPN, 240 volts, 12 ways ,powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43- IK-09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with following ratings & ways:- Note: (i) MCB’s /Isolators etc. shall be measured and paid for separately under appropriate item of Sch ‘A’.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (2020) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified and directed.

S&F 25 MM dia meduim Class PVC conduit along woth accessories in surface/Recess incl cutting the wall/ Floor and making good the same complete all as specified and directed.

M&L for Returning, filling in, including spreading leveling, watering and well ramming the excavated soil in layers not exceeding 25 cm thick complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead 32X 6 mm GI strip, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate No . 3 of MES Schedule Part-I (2020) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 40 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh incl necessary excavation and earth work in any type of soil, and PCC (1: 3 : 6) type C-1 (using 20 mm graded black trap/ granite/ Basalt stone aggregate) for earth pit with 40x40x6 mm mild steel angle iron frame for cover and 40 mm thick precast RCC cover in 1 : 2 : 4 type B1(using 20 mm graded black trap/granite/ basalt stone aggregate) with 3 Nos 8 mm dia TMT bars both ways with 12mm dia round bar handle, complete all as specified & directed . NOTE : RCC pit cover shall be pre-cast of RCC (1:2;4) type B-1 80 mm thick reinforced with XPM weighting not less than 4 Kgs/Sqm in lieu of CI cover.

M&L for Removal of surplus excavated soil to a distance not exceeding 50 Mtr distance and depositing as directed at a level not exceeding 1.5 mtr above starting point complete all as specified and directed.

All as per Srl item No 145.00 above but point wiring for one bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and directed.

M&L for Un-reinforced precast concrete cable cover class LV type I, flat, size 250mm x 150mm x 40 mm as proteciton to under ground cable laid dry flat adjoining each other complete all as specified and directed

Taking down Aluminum air termination rod of any size and type from floor/wall of bldg and deposited to MES store yard complete all as specified and directed

Supply & Fixing Single Pointed Air Termination Aluminium Rod 25 mm dia 300 mm long Complete all specified and as directed by Engineer-in-charge.

Supply & fix Test point terminal block made out of gun metal or phosphorus bronze size 75X75X25 mm, drilled and screwed including 3 Nos, 8 mm dia 25 mm long hexagonal head screws complete all as specified and directed by Engr-in-Charge.

Supply and Fix GI Strip 20X3 mm thick on parapet or surface of wall for lightning conductor complete as specified and directed by Engineer-in-charge. ( for horizontal run)

Supply and Fix GI Strip 20X3 mm thick on parapet or surface of wall for lightning conductor complete as specified and directed by Engineer-in-charge.(For vertical run)

Supply and Fix GI Strip 32X6 mm from earth electrode directly in ground complete as specified and directed by Engineer-in-charge.

Supply and fixing testing joint,made of 20 mm X3 mm thick GI strip 125 mm long, with 4 nos. of GI bolts nuts chuck nuts and spring washers etc, complete all as specified and directed by Engineer-in-charge

Supply and fix meduim grade Galvanised pipe 40 mm dia with all fitting fixed to wall ceiling or in floor complete all as specified and directed.