Provision of Storage Shed and Autoclave Room for Speed Breeding Facility

Earth work in excavation by mechanical means(hydraulic excavator)/manual means in foundation, trenches of drains at all levels, depth, lifts etc including dressing of sides and ramming of bottoms lift , including getting out the excavated soil & backfill again and disposal of surplus excavated soil as directed, including dewatering etc during excavation within a lead of 500m. All kinds of soil

Providing and laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : All works upto plinth level and above at all levels. 1:2:4 (1 cement(ultratech/ACC/Ambuja) : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of synthetic enamel paint all complete.

Providing and fixing of 40MM WALL PUF PANEL DENSITY= 40±2 KG/M³ alongwith flashing etc. material as per direction of Engineer-In charges inclusive of complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Paid only total length of section fixed not individual sheet.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of paint synthetic enamel, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. For fixed portion Powder coated aluminium (minimum thicknessof powder coating 50 micron).

Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required Powder coated aluminium (minimum thicknessof powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. With float glass of 5.50 mm thickness and Frosted Glass Film to be fixed on glass as per design at NABI.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge

Providing & fixing Stainless steel AISI 316 grade glossy/ satin finish specified size Push-Pull Handle in pairs in door/ window with necessary screws complete as approved by Engineer -in- Charge.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with rubber, etc. complete as per architectural drawings and directions of engineer in- charge. Pre-laminated particle board/Compact Sheet with decorative lamination on both sides. Sample available at Site.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

polestarengineers

Sudharshan Solution Provider Co.