SPECIAL REPAIR TO BLDG NO T-4, T-6 OF OR LIVING ACCN OF MAHAR AT ROORKEE

Amount

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M&L Plain cement concrete 1:4:8 type D2, 100 mm thick as in sub base to flooring complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L machine cut Kota stone slab flooriing 20-25 mm thick in floor set and jointed in grey cement slurry over and including 20 mm thick screed in CM 1:6 including grinding & polishing in granite finish complete all as specified and directed.

M&L machine cut Kota stone slab 18-22 mm thick in skirting set and jointed in grey cement slurry over and including 10mm thick plastering in CM 1:4 incl grinding & polishing complete all as specified and directed.

M&L 18-20 mm thick marble stone makrana doogri table rubbed White as in border between Kota stone flooring over and incl 20 mm thick screeding in CM 1:6 incl grinding & polishing all as specified & directed

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for joint free non skid coloured ceremic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for jointfree white glazed ceremic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed

M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection incl finishing the surface even and smooth without using extra cement complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp , insulation etc) or insulation boards/ slabs any thickness complete all as specified and directed.

M/L for 'E' board (Designer )ceiling 4mm thick (Everest )with GI framed work of size 4mm main 'T' 24x38.5mm and cross T of size 24X28.5mm thick made out of PGI sheet 0.30mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25mm thik and angle 24xx24x0.4mm covered with powder coated sheet 0.25mm thick for ceiling, ceiling boards 60cmX60CmX4mm thick, suspended with GI wire 2mm dia and upto 2 mtr long complete incl plugging in brick walls with steel rawl plugs @ 600mm C/C and complete all as specified and directed by Engr-in-Charge.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and directed

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and directed

Taking down cement or cement lime plaster on brick or stone walls etc incl raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on brick or concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick or concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over and incl a coat of birla putty complete all as specified and directed

M&L for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of white wash complete all as specified and directed

M&L for complete removal of existing treatment and preparing surface of old surface of wall and applying two coats of cement base paint complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of birla putty complete all as specified and directed

M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wood surfaces and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkhats or frame with shutters exc 1.5 sqm but n exc 4 sqm (without taking off shutters from the frame) complete all as specified and directed.

ditto as per item No 25 above but n exc 1.5 sqm each

Taking down shutters of any description exc 1 sqm but n exc 2 sqm each and refixing in same opening after easing and adjusting incl renewal of screws erc complete all as specified and directed

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or cement conc (1:2:4) type B1 as reqd depth of embedded portion exc half brick but n exc one brick complete all as specified and directed

S&F Framed work as in doors or gates of angle or other section Fe 410-W (Gde E250) quality-B with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 35 mm thick factory made plain framed, panelled shutters (any number of panels) with lock rail of 2nd class hardwood and panels of 9 mm BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces and fitted to chowkhats complete all as specified and directed.

M&L for 2nd class hardwood (SAL) fillets, square, rectngular or triangular in section exc 6 and n exc 13 sqcm clean sawn secured with nails or screws complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreature 1.18mm and fixed with tinned tack/galvanised wire staple all as specified.

S&F 35 mm thick factory made plain framed, panelled shutter (any number of panel) with lock rail of 2nd class hard wood and panels of 9mm B.W.P commercial ply of 12mm thick veneered particle board with commercial veneering on both faces and fitted to chowkhats complete all as specified and directed".

Hacking out old broken glass from wooden frame etc glazed with oil putty or fixed with wooden beading complete all as specified and directed.

S&F sheet glass 3.0 mm thick ordinary quality and glazing with and incl wooden beads/ oil putty in square n exc 0.5 sqm in each panes complete all as specified and directed.

S&F factory made steel windows with side hung shutters incl box type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed.

ditto as per Item No 36 above but without glazing bar

S&F mild steel framed work such as grills, grating etc with ends of bars shouldered and or riveted or forged in spikes , framed guard bars, barred iron doors , ladders, framed balusters, railings and similar conforming to Fe-290Gde E-165 complete all as specified and directed.

M&L preparation of new wooden/or wooden based surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specifed and directed

M&L for mild steel work as in hold fast complete all as specified and directed.

S&F mild steel butt hinges 100 mm medium weight , cold rolled mild steel and fixed complete all as specified and directed.

S&F 200 mm mild steel barrel tower bolt stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F 300 mm mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and incl a min 6 bolt and nuts four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 125 mm mild steel pressed handles oval type stove enamelled black complete all as specified and directed.

M&L for providing cement concrete type B-0 (12.5 mm graded stone aggregate) as in bed block for fixing hold fast complete all as specified and directed.

S&F solid PVC door frame of size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube , supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. Frame for top and bottom rails . M.S. Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & drawing

S&F PTMT butt hinge 100 mm size Make: Cat No 222 PRAYAG/Equivalent

S&F PTMT tower bolt 200 mm size Make: Cat No 233 PRAYAG/Equivalent

S&F PTMT tower bolt 100 mm size Make: Cat No 231 PRAYAG/Equivalent

S&F PTMT door handles 125 mm size Make: Cat No 202 PRAYAG/Equivalent

S&F vitreous china wash hand basin white flat back size 550x400mm including 01 No CP pillar tap 15mm, CP waste coupling 32 mm , PVC waste pipe 750 mm long and brackets incl cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed

S&F towel rail 600 mm long of PTMT fixed with and incl chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed.

S&F swivel shower of PTMT any colour for fixing with 15 mm pipe (min wt 40 gms) with shower arm 15 mm size 195 mm long with bend of 45 degree with flange of PTMT any colour (min wt 40 gms) complete all as specified and directed.

S&F PVC (SWR) floor trap of 75 mm diameter of outlet plain with grating including jointing with solvent cement complete all as specified and directed.

S&F bib taps cast copper alloy fancy type chromium plated with flange with crutch or butterfly handle, screwed for iron pipe or for ferrule of 15 mm bore and fixed complete all as specified and directed.

S&F Pillar taps, cast copper alloy,fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15 mm bore and fixed. Make : Cat No 8903 Prayag/Equivalent complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms) Make : Cat No 186 Prayag/equivalent.

S&F 15 mm Stop valve, fancy type, chromium plated screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed Make : Cat No 8518 Prayag/equivalent.

S&F waste coupling of PTMT dia 40 mm (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F waste coupling of PTMT dia 31/32 mm (half or full threaded) for urinal .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F PVC connection 15 mm size of length 450 mm with PTMT nuts and nylon washer complete all as specified and directed. Make : Cat No 323 Prayag/equivalent.

M&L for 32 mm waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flanges end bedded in redlead cement and other end fixed incl waste pipe 750 mm long complete all as specified and directed.

Demolition or breaking up drain pipe (salt/glazed ware, AC or reinforced) of any description 100/75 mm complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints , laid in floors or in trenches or to walls complete all as specified and directed.

S&F PVC (SWR) bends of 75 mm bore of any radius Make : Prayag / equivalent complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore single socketed in any length with rubber ring joints , laid in floors or in trenches or to walls complete Make : Prayag / equivalent complete all as specified and directed..

S&F PVC (SWR) bends of 110 mm bore of any radius. Make : Prayag / equivalent complete all as specified and directed.

Taking up or down steel water tubing of 15 mm bore and connections incl cleaning for refixing or removal to store complete all as specified and directed.

ditto as per item No 70 above but 20 mm bore.

S&F tubes 'medium grade' galvanised 15 mm bore with all fittings and fixed complete to walls and ceiling or laid under floors (open or concealed) complete all as specified and directed.

ditto as per item No 72 above but 20 mm bore.

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar incl all quoins , arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Dismantling water tank of capacity exc 500 & n exc 1000 ltrs capacity complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks , straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed

M&L for brick work with old size sub class 'B' bricks , straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Dismantling timber scantling 40 sqcm and over in section in any position complete all as specified and directed.

M&L for 2nd class hardwood (SAL) as in scantling, clean sawn complete all as specified and directed

S&F rortational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

S&F 20 mm bore ball valve high pressure of PTMT epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. Make : Cat No 152 Prayag/equivalent.

S&F gun metal globe gate valve with iron wheel head screwedof 20 mm bore both ends for iron pipe and fixed all as per specified and directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade made with grey cement and no pigment including 25 mm thick sand cushioning complete all as specified and directed.

S&F Vitreous China urinal half stall type flat back of size 590 mm x 375 x 390 mm white (minimum) with chromium plated waste fitting grating and union for discharge pipe (excluding flusing cistern, flush pipe ) including urinal spreader of CP and PVC waste pipe of adequate length complete all as specified and directed.

M & L for grinding and polishing of existing terrazzo/ Kota stone floor and dado and treating the surface with wax polish completed all as specified and directed by Engr-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete incl fixtures and fittings swithes, ceiling rose, pendant, regulator, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

Taking down carefully any type and sweep of fans and any capacity of geysers kept in the safe custody and refixing the same after servicing and painting of two coat and MES numbering of existing paint by spraying including filling cavities with filler for fans complete all as specified and directed by Engr-in-Charge.

M & L Concealed Point wiring with 1.5 Sqmm(Nominal area) PVC insulated and PVC unsheathed FRLS multi stranded copper conductor single core cable drawn through and including PVC non metallic conduit of 20 mm dia ISI marked with complete accessories,including sunk mild steel 1.6 mm thick terminal boxes with 3 mm thick bakelite sheet top cover ISI marked complete including PVC insulated and unsheathed single core multistranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth and earth dolly ,making good surface with white wash or any type distemper as per existing colour of building complete all as specified and directed for the following :- Make of Cable- Havells /policab/Finolex, Make of PVC conduit -Plaza /Kalinga/Polycab (a) One light point controlled by one one way switch

(b) One fan point controlled by one one way switch,

(c) One 3/5 pin socket outlet 5 Amp on the same board with other swithes

(d) One 3/5 pin 5 Amps socket outlet on independent board.

All as per item No 91 above here in but with 2.5 Sqmm (nominal area) FRLS cable PVC for the 15 Amp 3/5 pin socket power point including 2.5 Sqmm copper conductor green as per colour coading for earth contineuity all as specified. Make Plaza/Polycab/Havells for cable and Kalinga/Plaza/Polycab for conduit.

S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 15 Amps complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type.Make: Havells / Anchor (Penta) /Legrand”

S&F socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type.Make: Havells / Anchor (Penta) /Legrand”

Supply & Fixing Angle holder (metal ring) PVC / polycarbonate type with back plate, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed. Make:- Havells, Anchor(Penta), Legrand

S&F electronic fan regulator 230 volts , step type (5 step) socket type ,hum free 100/300 watt complete all as specified and directed.

M&L for Ceiling rose in poly carbonate 3 terminal brass flush type 6 Amps,250 volts AC ISI marked, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed.

S & F in replacement of LED tube light fitting 1x20 Watt LED box type industrial batten type with bipin holder, connectors block complete with all accessories and including 20 watt retrofit LED tube rod T8 polycarbonate complete and making conncetions with the help of three core PVC insulated unsheathed copper conductor multistanded wire of suitable length & suitable in size complete all as secified and directed. Make C&S Cat Part No LTDC1220WLED/WD(LTDC161820WLED + LT4f20WLEDT8/WD) or equivalant in Philips/Bajaj.

S & F in replacement of old unserviceable light fittings and Supply and fixing security light fitting versatile pressure die-cast aluminium with high power LED 25 W as light source complete with LED 25 W 5000K including brackets made out of GI pipe light grade pipe bent to shape incl 02 Nos MS flate clamps incl nut bolts connection complete all as spd and directed .Make : C&S cat part No. LTESSE25WLED or equivalent in Bajaj/Havells

S & F in replacement of Distribution Board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 12 way IP 43 double door with 200 Amps rated copper bus bar neutral bar ,earth bar, flush to wall complete all as specified and directed MAKE-LEGRAND/Indo Asia/ C&S

S&F in replacement of Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof TPN 4 way IP 43 double door with 200 Amps rated copper bus bar neutral bar ,earth bar ,triple pole and neutral 415volts ,flush to wall complete all as specified and directed.MAKE-LEGRAND/Indo Asia/ C&S

S & F in replacement of MCB SP 6-32 Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/thimbles compelte : Make Legrand/Indo Asian/C&S

S & F in replacement of MCB SPN 40 Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/thimbles compelte : Make Legrand/Indo Asian/C&S

S & F in replacement of MCB SPN 32 (DP) Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/thimbles compelte : Make Legrand/Indo Asian/C&S

S & F in replacement of MCB TPN 63 Amps, four pole, AC 415 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/thimbles complete Make :Legrand/Indo Asian/C&S

S & F in replacement of concealed sub main wiring with two runs of single core FRLS PVC insulated and unsheathed multistranded, copper conductor cable of size 6.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20mm /approprite dia with accessories and fittings and one run of 6.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm/approprite dia shall be measured as one run length, Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the conduit pipe (Note :- Extra length of cable required for connection to MCBs shall deemed to be included in unit rate.) Make of Cable- Havells /policab/Finolex, Make of PVC conduit - Polycab/plaza/Kalinga

M&L earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.3 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron wire 4mm dia size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 20 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) (chamber size not less than 300x300x300mm interier diamentions), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified. NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point. and chamber shall be made 0.5 mtr away from the earthing pit.

Supply, laying LT cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts grade of size 25 sqmm 3.5 core complete all as specified and directed.

Supply and lay in trench/floorwall/hard standing GI pipe light grade 40 mm bore including its necessary fitting such as bends sockets etc for cable protection complete all as specified and directed.

Excavation in trenches not exc 1.5m vide and not exc 1.5mtr deep in any type of soil(soft/lose/hard/dense soil) for laying/taking up/taking down of electric power cable and getting out and levelling of bottom surface to required level all as specified and directed.

Returning, filling including spreading, leveling, watering and well ramming soils in layers not exceeding 25cm thick all as specified and directed.

Removing excavated material from site to a distance n exc (50mtr away and exc 1.5 m above the starting point all as specified and directed by Engr-in-Charge.

Material and labour for river washed and screened dry sand for filling in trenches below and around undergroung cables for cushioning of cables etc complete all as specified and directed.

S & lay in trenches sub class 'b' bricks having compressive strength 75Kg/Sqcm for cable protection etc complete all as specified and directed by Engr-in-Charge.

Supply & fix LED Blub 15 Watt hoder type make : Philips/Hellonix/Bajaj

AMAR NATH SHARMA

KISHORE CHAND DINESH CHAND

Alankar Traders

A ONE BUILDERS AND ENGINEERS

sagar associates

RAJENDER CONSTRUCTION CO

m/s rajesh bros.

M/S A.K GARG

M/S RAJESH ARORA

AJAY KUMAR CONTRACTOR

KAPOOR ELECTRICALS

Bhardwaj Construction Co

M/S IRFAN AHMAD CONTRACTOR

VINAYAK CONSTRUCTION COMPANY

SMG Construction