CMLRRP 2020 - 21Re tarring and Concreting work of Stadium Murukan Kovil Murinjakalumku road in Collage ward 31in Punalur Municipality

Amount

PROTECTION WALL

11.1.1.1 : Excavation for StructuresEarthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I.Ordinary soil(i)Upto 3 m depth

od813399/2020_2021 : DRY RUBBLE MASONRY- Dry rubble with out concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials , labour charges etc. Complete as per direction of Departmental officers at site

od864247/2020_2021 : Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and Random rubble masonry In cement mortar (1:6)

12.3 : Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

ROAD WORK

3.1 : Preparation of Foundation for EmbankmentScarifying Existing Granular Surface to a Depth of 50 mm by Manual Means Scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per Technical Specification Clause 301.4.

3.5.1 : Excavation in Cutting in Soil by manual means with lead upto 50 mExcavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

od813407/2020_2021 : Granular sub-base/base/surface course with local materials (Table 400.13) by mix in<br>place method normal. Construction of granular sub-base by providing local material spreading in uniform<br>layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and<br>compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per<br>Technical Specification Clause 408.<br>(i)Using naturally occuring gravel<br>

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

75.5.5.A.1pb : Modified Penetration Macadam 50 mm thick using Bitumen S-65 - Packed Bitumen Rates <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.1.1pb : Prime Coat - Low porosity - With Packed Bitumen Rates <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.2.1pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.2.2.Pa : Plastic Roads - Bitumen S-65 <br> 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 (with 7% of bitumen replaced by shredded waste plastic) Case - I By Manual Means (II) Bitumen (S-65) (VG - 30)

75.5.12.A.3.2pb : Seal Coat - Manual Means - Type C - Bitumen S-65 - Packed Bitumen Rates <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 A. By Manual Means <br> Case III : Type C (II) Bitumen (S-65)

CONCRETE WORK

3.5.2 : Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

od611919/2020_2021 : Construction of plain cement concrete pavement , thickness as per design , over a prepared &lt;br&gt;sub grade / sub base, with 43 grade &lt;br&gt;cement or any other type as per per clause 1501.2.2 M20 (grade) , coarse and fine aggregate conforming to IS 383 , maximum size of course aggregates not exceeding 25 mm , mix in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design , laid in approved fixed side form work ( steel channel , wedges steel plates including levelling the form work as per drawing) , spreading the concrete with showels , rakes, compacted using needles vibrators and finished in continuous operstion including provision of contraction and expansion , construction joints , curing of concrete slabs for 14 days with water finishing to lines and grade as per drawing and technical specifications clause 1501.

SIGN BOARDS

10.2.A.2.4 : Traffic Signs A. Retro-reflectorised Traffic Signs 2 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 <br>4 800 mm x 600 mm Rectangular

10.4.A.1 : Direction and Place Identification signs with size more than 0.9 sqm size board A. Retro-reflectorised Traffic Signs 1 Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

od818453/2020_2021 : Providing and erecting a &quot;W&quot; metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.3&lt;br&gt;(Modified Data MoRTH 8.23.A)

od813416/2020_2021 : Fabricating Welding Supplying fixing in concrete steel project information board including painting and lettering and submitting a photo of same at site complete

od864259/2020_2021 : Supplying and fixing name board of size 75x60cm installed in appropriate place visible to public made of brick wall with granite plaque should be inserted and engraving letters etc complete as direction of dept officers at site

SIVAN PILLAI

NARAYANAN S

Bidder Name

NARAYANAN S

SIVAN PILLAI

S SURENDRAN PILLAI