Spl repair to Bldg No T-4 of 217 Fd Wksp Coy EME, Provn of Toilet block near Fresh issue shed of 447 Coy ASC Coy and Certain repair/ seepage and connected works at 1 x Toilet block of KV upper camp under GE Dehradun.

Amount

Demolition brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M& L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM ( 1:6 ) using old size bricks complete all as specified and as directed by Engr-in-Charge.

All as per item No. 03 here-in-above, but except brick complete all as specified. (Old bricks shall be re-used obtained from demolition).

M&L brick work with sub class 'B' brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall complete all as specified.

Taking down cement plastering of any description on brick/stone/concrete wall surfaces of any description incl racking out joints hacking for key,scrubbing down with water etc. complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L for rendering 15 mm thick in cement mortar 1:4 using WPC in roof surfaces finished even and smooth without using extra cement ( WPC used , If ordered by Engineer-in-Charge), complete all as specified and directed.

M&L for complete removal of existing treatment from wall upto brick work or plaster surface by electric sand paper grinder, washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper complete all as directed by Engr-in-charge.

M & L for taking down existing treatment (membrane) including picking, sweeping clean and washing down with water to remove dust & providing APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application, shall be laid over hot blown bitumen grade 85/25 conforming to IS 702 @ 1.2 kg per Sqm over a coat of bituminous primer and applying aluminium reflective paint over it complete all as specified and directed. Note : The work of water proofing treatment shall be got executed through original manufacturer or authorised applicator only.

M&L for two coats of oil bound distemper over a coat of alkali resistant primer on internal wall surfaces over prepared putty surfaces complete all as specified in SSR Part I and directed Engr-in-Charge.

M&L for preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified

M&L preparing new plastered surfaces and applying 3 coats of white wash on walls etc complete all as specified and as directed .

M&L for two coats of oil bound distemper over a coat of primer on new surfaces prepared by putty complete all as specified.

M&L for preparation of wall and applying interior grade wall care putty 1.50 to 2 mm thick to make the surface smooth as specified and directed by Engr-in-Charge. (Make : Berger/Asian/JK/Birla

M&L for preparation of newly plastered surface of wall and applying two coat of exterior emulsion paint (APEX) over a coat of primer complete all as specified

M&L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified

Taking down wooden chowkhats or frames with shutters of any description n. exc 1.5 sqm each (without taking off shutter from the frame) complete all as specified.

All as per item No 19.00 here in above but exc. 1.5 Sqm and not exceeding 4 Sqm each complete all as specified.

S&F Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified (Note: framed filled in cement concrete1:2:4 type B0 (12.5 mm stone aggregate)

Taking down shutter of any description, exc. 1.0 Sqm but n. exc. 2 Sqm each and removing from site complete all as specified.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified Make :- Kitply/centuryply or as approved by GE.

S&F factory made 100% solid wood plastic composite (WPC) door frame of size 75 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex or as approved by GE.

S&F 24 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side plain with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex or as approved by GE.

S&F powder coated aluminium ventilator fixed type half glazed and half gauged with and including hardware fittings, glazing, wire gauge, rubber packing, aluminium beading etc. as specified below including taking down old window/ventilator and making good of wall surface to match with existing surface complete all as specified and directed :- Frame : 44.5 x 44.5 mm x 1.80 mm thick Middle rail : 44.5 x 44.5 mm x 1.80 mm thick Glazing: 5 mm thick frosted glass fixed with rubber gasket and aluminium beading. Wire gauge: stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with aluminium beading.

M&L for complete removal/ demolition of existing treatment of sunken portion such as WC & bath etc using the following specification for sunken floor: (a) Clean the complete surfaces including rubbish for sunken and washing down with water. (b) Plaster for sunken portion in CM (1:3) with WPC (Dr. Fixit or equivalent) as per manufacturer's instructions. (c) Preparation of surfaces and applying one coat of polymeric primer @ 0.30 Kg/Sqm. (d) Supply and providing APP based polymeric water proofing members 3 mm thick of weight not less than 3.00 Kg/ Sqm. (e) Applying one coat of bitumen 85/25 @ 1.2 Kg/Sqm. (f) M & L for PCC 1:5:10 type E2 mixed with brick bats 40 mm size. (g) M & L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) 40 mm thick finished even and smooth as specified.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete all as specified.

S & F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay,tower bolt etc. complete with glazing bars, dovetailed or welded complete all as specified.

S & F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay, tower bolt etc.complete without glazing bars, dovetailed or welded complete all as specified.

S&F powder coated aluminium grill with frame fixed with stainless steel screws complete all as specified and directed.

S&F 0.56 mm dia stainless steel wire cloth with average width of aperature 1.18 mm and fixed with stainless steel wire staples or moulded beading complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified.

S & F stainless steel barrel tower bolts 200 mm long grade 304 one piece and fixed complete all as specified

S & F stainless steel barrel tower bolts 150 mm long grade 304 one piece and fixed complete all as specified

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 150 mm long Aluminium anodised handles of fabricated type complete all as specified and as directed by Engr-in-Charge.

S & F stainless steel butt hinges, medium weight 100 mm long grade 304 one piece and fixed with screws/welded to frame ,complete

S & F stainless steel handles 150 mm long grade 304 one piece and fixed with screws/welded to frame ,complete

S & F stainless steel handles 125 mm long grade 304 one piece and fixed with screws/welded to frame ,complete

S & F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy & fixed and compete all as specified and directed.

M & L floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 140 mm complete.

Taking down/ dismantling asbestos (corrugated, semicorrugated, etc.) sheets in roof coverings etc complete all as specified.

Dismantling of framed or unframed timber scantlings 40 sqcm and over in section, in any position complete all as specified and directed.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W(Gde E-250) quality-A complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed.

M & L for two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified.

M & L for one coat of synthetic enamel paint on old painted steel surfaces of any description including preparation of steel surfaces complete all as specified.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamel Paint complete all as specified

M & L for two coats of Synthetic paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified

Dismantling floor, hearth or wall tiling/ terrezzo toping including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate) as in floor/subfloor/levelling course finished even and fair complete all as specified and as directed.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 6- 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 6- 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 15 mm thick screed bed in cement mortar 1:4 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L for coloured digital ceramic tiles in vertical surface as in walls, dado, etc. of size 375 x 250 x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchover and including 10mm thick rendering in CM (1:4) complete all as specified.

M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match complete all as specified.

M&L for prepolished precast factory made coloured chequred cement paver tiles of size 300mmx300mmx20-22 mm thick set and jointed in neat cement slurry and pointed in white cement mixed grey coloured pigment to match including 20 mm thick screed bed in bedding layer (1:6) complete all as directed.

All as per item No 61 here-in- above but as in skirting over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed.

M&L for Machine cut kota stone as in skirting 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L heavy duty endura ceramic coloured tiles 10 mm thick dark shade (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L cutting holes in brick wall built in cement mortar exc half brick but nexc one brick for inserting hold fast etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified.

M & L 75 mm th PCC (1:3:6) type C-2 as in plinth protection, finished even and fair without using extra cement.The plinth protection shall be laid in alternate bays nexe 2sqm, 10mm joints shall be provided joints shall be filled with bitumen mastic, bitumen mastic comprises of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work and demolition of existing old cement concrete (un-reinforced) not exc 15 cm thick in ground floor and paving below or above ground level complete.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in any type of soil complete all as specified and directed by Engr-in-charge.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc complete all as specified.

M&L 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base etc complete all as specified and as directed by the Engr-in-Charge.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drain including necessary form work complete all as specified.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soil complete all as specified and directed by Engr-in-charge.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engr-in-charge.

M&L 18 to 20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified

M&L grinding and polishing to edges and rounding of granite kota or marble slab etc and smooth finishing complete all as specified and as directed

S&F in repair SS grade 204 drapery rod 20mm dia including decorative brackets, decorative finals at both ends complete all as specified.

Supply and fix in repair aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60x44.45x1.60mm Shutter verticle style :- 85x44.45x1.56mm Shutter middle Rail :- 83.50x44.45x1.54mm Shutter Top Rail and bottom Rail :- 114.30x44.45x1.55mm Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S & F in repairs powder coated Aluminium partition (fixed) made out of aluminium powder coated section 83 x 44.45 x 2.00 mm including 5 mm thick glass/ ACP Sheet complete with rubber packing/ aluminum beading etc including dismantling of existing structure complete all as specified and directed

S & F in repairs aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter andone nos wire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows, and glazed with tinted glass coloured glass 4mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc complete all as specified and directed. Shutter Top & bottom size : 37.50x15x1.60mm Shutter inner lock size 37.50x15x1.60 mm Shutter side (Handle) size 37.50x15x1.36 mm Chowkhat bottom size : 50.30x26x1.20mm Chowkhat top & sides size: 50.30x26x1.00mm

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair Aluminium (Die Cast body) Door closer hydraulically regulated designation No 1 universal type suitable for door shutters up to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & directed.

S&F in repair Brass Mortice lock, four levers vertical type, of 100 mm size complete all as specified.

S & F rotational moulded polyethylene water storage tanks of Capacity 1000 litres, tripple layer, white colour, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete all as specified.

S&F Rotational moulded polyethylene water storage tanks of 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including supply & fix 20 mm dia GI light grade wash out pipe 450 mm long with plug and 20 mm dia GI light grade over flow pipe 600 mm long with fitting complete all as specified.

S&F in repair half stall china urinals (wall type) complete incl plugs, bedding urinal to plugs with and incl 60 mm long screws, pointing around urinal back in cement and waste pipe etc complete all as specified and directed by Engineer in Charge. Make : - Jaquar/URS-WHT-13261 size 340 x 310 x 660 mm/Hindware vinenzia Cat Part No 60023 Stan white pastel size 31.5 x 34.5 x 66 cm/Parryware Cat Part No Aquaseal and neutral size 360 x 345 x 565 mm.

Taking up or down steel tubing and connection with fittings incl removal from site bore of pipe 15mm complete all as specified.

Taking up or down steel tubing and connection with fittings incl removal from site bore of pipe 20mm complete all as specified.

Supply & Fix in repairs PVC connection 15 mm dia 450 mm long with brass fly nut at both ends complete all as specified

Supply only PVC connection 15 mm dia 450 to 600 mm long with brass fly nut at both ends complete

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti syphonage pipe etc and making good to floor complete all as specified.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) water closet, including 600 mm long CI P-trap, connection to trap and to flushing pipe, anti syphonage pipe etc, and making good to floor complete all as specified and as directed by Engr-in-Charge.

S & F in repair 10 litre capacity PVC low level flushing cistern ‘ white’ with inlet, float valve including brackets with 32 mm dia PVC pipe/bend 600 mm long complete. Hindware/Parryware/Jaquar.

S & F 10 litre capacity PVC low level flushing cistern ‘ white’ with inlet, float valve including brackets with 32 mm dia PVC pipe/bend 600 mm long complete. Hindware/Parryware/Jaquar.

S & F in repair 75 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall / laid in trenches complete all as specified

S & F in repair 110 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall/ laid in trenches complete all as specified

S & F in repair 75 mm bore UPVC (SWR) bend with oval acess door ,'T'socket reducer etc complete all as specified.

S & F in repair 110 mm bore UPVC (SWR) bend with oval acess door ,'T'socket reducer etc complete all as specified.

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 75 mm dia pipe complete all as specified.

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe complete all as specified.

S & F 110 mm dia PVC (SWR) vent cowl complete all as specified. Make : Supreme/finolex or as approved.

Supply and fix in repair 32 mm dia PVC waste pipe for WHB and sink 90 cm long with union, complete all as specified and directed. equivalent).

M & L for demolition of existing PCC, cleaning and preparation of surfaces and treating of joints, filling of honey combs and providing 25 mm thick PCC (1:2:4) type B-0 with WPC over roof surface complete all as specified and directed.

S & F in repair vitreous china wash hand basin white, oval type counter top of size 550mmx400mm including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe, waste fitting etc. complete all as specified. Make : Jaquar (FLS-WHT-5701) or equivalent in Hindware/Parryware.

S & F in repair vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc complete all as specified. Make : Jaquar (CNS-WHT-301) or equivalent in Hindware/Parryware.

S&F Vitreous China wash hand basin, white, flat back type of size 550mm x 400 mm fixed on and including cast iron cantilever bracket, 32 mm dia brass waste coupling and 32 mm dia PVC waste pipe, grating dome, CP pillar tap etc including fixing of tap, waste fitting etc complete all as specified.

S&F 15mm dia swan neck pillar tap (for oval type WHB) brass chromium plated with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, and fixed complete all as specified and as directed by Engr-in-Charge.

S&F in repair pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaguar/Cat part No. KUP-35001PM/Hindware Cat Part No:F370001/Parryware Cat Pat No.T4302A2

S&F in repair 15 mm bore Angle cock/stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make : - JAGUAR Cat Part No FON-40053/Hindware Cat Part No F160017/Prayag Cat No 9410.

S&F fancy type concealed stop valve, cast copper alloy, with crutch or butterfly handle, screwed down both ends for high pressure, as per ISI suitable for 20mm dia iron pipe complete all as directed.

S&F in repair 15mm bore Bib taps long body cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - JAGUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Prayag CAT Part No S9906.

S&F in repair CP Health Faucet with 1.20 mtr metalic expandable tube & hook complete. Make : Jaquar Cat No.ALE-ESS-585/Parryware Cat No. T9941A1 or equivalent in Hindware or prayag.

S & F 15 mm bore bib taps, chromium plated cast copper alloy long body, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

Supply and fix in repair CP grating 100mm to 125 dia round fix on floor/ nahani trap with /without hole fixed with cement mortar, complete all as specified and directed.

S&F in repair looking mirror mounted on decorative type PVC frame fixed to wooden plug with CP brackets screw fixed, complete all as specified. Make: Prayag or equivalent as approved.

S & F in repair 20 mm dia brass chromium plated towel rack of 3 sets type 60cm long between flanges including pair of fixing brackets complete all as specified and directed. Make: Jaquar Cat Part No AKP-35781PS/CAN-1181FHS or equivalent in Hindware.

M & L in repair 75 mm CI spun casted floor trap with grating including jointing with solvent cement 75mm bore outlet complete all as specified.

M & L PVC (SWR) floor trap plain with grating including jointing with solvent cement 75 mm bore outlet complete all as specified.

S & F PVC (SWR) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 110 mm dia bore of pipe complete all as specified.

S & F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete all as specified.

S & F in repair 15 mm dia bore chromium plated concealed stop cock, complete all as specified. Make :Jaquar/Hindware/Parryware

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S & F in repair 20 mm dia bore gun metal gate valve complete all as specified and directed. Make :Zoloto/ Leader or equivalent as approved.

S&F 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified. Make :Zoloto/ Leader or equivalent as approved.

M & L for grinding & polishing of existing kota stone / terrazzo floor etc using mechanical grinder complete all as specified and directed by Engineer-in-Charge.

Supply & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling of any type at all heights as per direction of Engineer-in-Charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

M&L for providing damp proof course 40 mm thick in cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) to horizontal or vertical surfaces mixed with integral water proofing compound as per manufacturere instructions including necessary formwork complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid seperately.

M&L for RCC Type B-1, 1:2:4 nominal mix (using 20 mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span RCC band etc complete all as specified.

M&L for Providing precast cement concrete 1:2:4 nominal mix type B1 (using 20 mm graded aggregate) set in cement mortar 1:4 in landings, cover slabs (for man holes, septic tank etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified.

M&L TMT bars 06 to 08 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 132 here-in-above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L for construction of soakage well, internal dia 1.8M dia & effective depth 3.00M including excavation in any type of soil complete all as specified and shown on TD drawing & directed.

M&L Formwork to fair finished surfaces to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and openingcomplete all as specified.

M & L for moorum / red bajari filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering and duly consolidating complete all as specified and directed.

M&L for hardcore of broken stone of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces complete all as specified and as directed.

M&L for screed bed bedding layer 15 mm thick in cement mortar (1:6) for laying of floor finish complete all as specified and as directed .

Supplying, fixing, jointing and testing galvanised steel water tubing 15 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing 20 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

M & L cutting chases for concealed water tubing or concealed conduit wiring, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges, etc., cutting not exc 10 cm width or girth complete all as specified & directed.

S & F brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule complete all as specified.

S & F Chromium Plated brass soap dish fixed to wall with chromium plated brass screwed and cup washer complete all as specified and directed.

S & F brass chromium plated towel rail, 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

Supply only integral waterproofing compound complete as per manufacturer instructions.

S&F 150mm internal dia of pipe salt glazed stoneware drain pipes, laid in trenches and jointed in cement & sand mortar 1:1, complete all as specified and directed.

M&L for Concrete bed in 1:3:6 type C2 to 150 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified.

Taking down and re-fixing the existing shutter in same opening after & including necessary easing/ repair etc. exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) any type including unscrewing from board,fitting and fixture such as switches, ceiling roses, holders, regulators sockets ,light fittings etc removing materials from site and making good disturbed with the existing surfaces complete all as directed.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed iron/steel suction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and making good to walls,floors etc complete all as specified and directed by Engr.-in-charge of following. Note : The wiring to be done as per IE rule and maintain colour code accordingly.

One light point / Exhaust fan point controlled by one way switch.

One fan point , controlled by one way switch through Regulaor

One three pin 5 Amp socket on same board with other switches

One three pin 5 Amp socket on independent board

All as per Item No 153 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete all as specified.

S & Fix Switch piano flush type single pole one way 230 Volts 6 Amp complete all as directed.

S & Fix Socket outlet 3 pin , 230 Volts 5/6 Amps flush type multipurpose 5 pin complete all as specified

Supply and fix Socket outlet multipurpose having provision for 3 pin, 230 Volts 15/16 Amp and 3 pin, 5/6 Amp, piano flush type IS: 1239-1988 marked with valid CML No complete all as specified.

Supply and fix Switch piano; flush type, single pole, one way, 230 Volts 15/16 Amps complete all as specified

S & Fix in repairs for Lamp holder polycarbonate insulated body, with back plate suitable for batton fitting complete all as specified.

S & Fix step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts, 6 Amps 120 watts complete all as specified .Make HPL/Havells/Anchor

Supply and fix Ceiling rose, Three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified Make HPL/Havells/Anchor.

S&F in repair wall mounted LED tube light fitting 1x20 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No BN 021 C LED 20 S PSU CW GR S2 /Havells ENDURALINEARNEOBS20W LED840SPCWH / Wipro LL20-281-XXX-65AL1 or equivalent in Eveready.

Removing /Refixing of LED tube light fittings / LED fancy light fittings of any make or capacity carefully complete (taking down included ser item No 152 of point wiring) all as specified and directed by Engineer-in-charge

S&F in replacement of fully diffused recessed mounted 2'x2' LED luminaire with UGR<19, for Full Glow Office Complaint indoor spaces, LED 36 Watt ,6500K in White & gray housing with profiled & flat diffuser all as specified and directed by Engineer-in-charge. Make : Philips cat no RC 380B LED36S-6500G4L60W60PSUODOC OR Equivalent in wipro/Havells/Eveready.

S&F in replacement of energy saving ,surface mounted, LED 10 watt Bulk head luminaire with decorative oval diffuser comprrising of high brightness LEDs complete all as specified and directed by Engr-in-charge. Make : CG cat LBHP-10-CDL/Philips WT140W LED7S CW PSU S1 PC/Havells ENDURA RUGBYNEO N /Mepro cat no BCL 23 Plain or equivalent in Eveready.

Supply and fixing in replacement of Busbar chamber of size 600x315x214 mm or higher size with PVC hinged lid suitable for and mounting arrangement for fixing of MCCB 4 pole, 100/125 Amps 25 KA (Icu=100%Ics) 415 Volt,50 Hz, duly connected with and incl 04 Nos of copper Busbar 300 Amps fixed on epoxy insulators, Gun metal cable gland of 25 Sqmm 01 No and PVC coupler for sub main wires 04 Nos complete Polycarbonate type (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV resistant, having high grade gasket made of Polyurethane, flame retardant,complete all as directed at site by Engr in charge or his rep complete. Note:- Only MCCB shall be measured and paid for seperately all other items incl connection from MCCB to busbar with suitable size copper wire incl thimble, bottle lugs etc are incl in item rate. Make:- Hensel cat No Mi 9410 or ABB/BCH/Universal/Schneider

S&F Ceiling fans complete with blades ,down rods, and accessories, 230V,1200mm sweep,340 RPM,200CMM,50Watt with suitable size of fixing arrngement to MS channel or Angle iron arms as all specified & directed directed Make : CG model kassels 50 ISI SKU code 250467 or equivalent in Havells/Bajaj/Usha or as approved.

S&F exhaust fan,steel body AC single phase ,230 V of size 300mm sweep ,1400 RPM,1300CMM,70 watt with , blades, and frame and louvers make :CG model MAXX AIR sku code 70046 or equivalent in Havells/Bajaj/Usha or as approved.

Removing & Refixing of old serviceable ceiling fan with and including suitable fan hook as per site requirement made of MS flat etc to existing truss / runner of any type complete all specified & directed.

Supply and fixing in replacement for Distribution board SPN 8 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection.Note:- DB and MCCB/MCB shall be of same make Make:- Legrand/Hager/L&T

Supply and fixing in replacement for Distribution Box MCB Protected Socket with sheet steel enclosure 20 A MCB DBOXX Combo DP including PLUG TOP all as specified & directed Make : Havells/LEGRAND/L&T

Supply and fix in repairs MCCB 100 Amps FP 415 Volts having breaking capacity 16 KA with and incl spreader link kit complete suitable for fixing as incoming in polycarbonate busbar complete all as specified and directed.

S&Fix in repairs MCB single pole 240 volt, 10 KA, 5-32 Amp, 'C' series confirming to IS complete all as specified and directed.

S&Fix in repairs MCB SPN 240 Volt 10 KA 32 Amp 'C' series conforming to IS complete all as specified & directed.

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) drawing in and including 20 mm dia or higher medium duty PVC concealed conduit/flexible conduit where reqd and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly complete incl taking out old unserviceable submain all as specified & directed. Make: Havells/Finolex/L&T/Polycab (Note: Three run 4 Sqmm cable and one run conduit shall be measured as one run)

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium duty PVC concealed conduit/flexible conduit where reqd and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 6 Sq mm as earth wire upto common earth and connected to earth dolly complete incl taking out old unserviceable submain all as specified & directed. Make: Havells/Finolex/L&T/Polycab (Note: Three run 6 Sqmm cable and one run conduit shall be measured as one run)

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized wire 4 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 15 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR part 1 including testing on completion all as specified and directed. incl demolition to existing earthing complete all as specified.

Supply & Laying in replacement XLPE insulated armoured heavy duty electric cable , with multi stranded aluminium conductor served with an inner sheathing of PVC type armoured with galvanized steel wire or tape and PVC sheathed 1100 volt grade,nominal cross sectional area 35 Sqmm 3.5core inclu lugs and heat shrinkable PVC Sleeves on exposed surfaces & teflon tape duly insulated complete laid in trenches, ducts, drawn through pipe across the road/path/alongpoles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-charge. Make: Havells/Polycab/Glandlay

M&L for sand cushioning in trenches for protection of UG cable with river based sand laid dry in trenches before and after laying of cable, incl well ramming complete all as specified and directed

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified & directed.

Supply & Laying in replacement of GI Steel tubing light grade 40 mm(2") dia including all fitting laying in trenches across road or grouting /fixing on wall for protection of cable complete all as specified and directed by Engr-in-charge.

M/S JAI PRAKASH GOEL

SRI GANESH ENTERPRISES

M/s RAM RATAN AND SONS

M/S C S AITHANI

M/s Teg Singh Negi

RIZCON