Loading
Loading…
Loading…
Tender Value
₹3.0 Cr
EMD Value
₹6.1 L
Closing Date
23 Jul 2026, 11:00 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
GSPGT
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' which ever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Appendix-J, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet
Statement showing Annual Contractual Turnover Data (as per Annexure - J of Tender Document) for the Previous 3/4 Years (Contractual Payment only) supported by Audited Balance Sheet duly certified by the Chartered Accountant shall be enclosed alongwith the bid. Non-submission of the same by the bidder shall result in summarily rejection of his/their bid
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: 1. Three similar works each costing not less than the amount equal to 30% of advertised value, or 2. Two similar works each costing not less than the amount equal to 40% of advertised value or 3.One similar work each costing not less than the amount equal to 60% of advertised value Note: Separate completed works of minimum required values for each component can also be considered for fulfillment of technical eligibility criteria for different components. *Similar Single work is defined as "Works involving supply, installation, testing and commissioning of outdoor/indoor substation equipments of 11kV or above voltage".
The tenderer shall submit along with the tender document, documents in support of his/their claim to fulfill the eligibility criteria as mentioned in the tender document. Each page of the copy of documents/certificates in support of credentials, submitted by the tenderer, shall be self- attested/digitally signed by the tenderer or authorized representative of the tendering firm. Self-attestation shall include signature, stamp and date (on each page). Only those documents which are declared explicitly by the tenderer as "documents supporting the claim of qualifying the laid down eligibility criteria" will be considered for evaluating his/their tender. Note- The tenderer shall attach a summary of documents submitted for satisfying the eligibility criteria either duly self attested or digitally signed
22 conditions · 3 needing a document upload
The Supply of Goods and Services would be subject to GST Act and Rules applicable from time to time.
I/We have read the various conditions to tender in the attached tender document and agree to abide by the said conditions.
I/We agree to keep this tender open for acceptance for a period of 45 days from the date of closing of this tender and in default thereof I/We will be liable for forfeiture of my/our Bid Security. I/We offer to do the work for Railway, at the rates quoted in the attached Schedule and hereby bind myself/ourselves to complete the works in all respects.
I/We also hereby agree to abide by the updated Regulations of Tenders and Contracts and General Conditions of Contract issued by the Engineering Department of Indian Railways along with correction slips issued from time to time and to carryout the work according to the Special Conditions of Contract and specifications of materials and works as laid down by Railway in the Annexed Special Conditions / Specifications, Schedule of Work for the present contract.
All rates quoted in the tenders shall be deemed to be inclusive of CGST, SGST, IGST etc., payable by the contractor to the Government or any public body and no additional amount/rate or claim will be entertained on this account by the Railways. Also no claim whatsoever will be accepted by Railways on account of revision of tax rates, new taxes of statutory nature by State/Central Govt.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall go through the entire tender documents thoroughly and strictly adhere the instructions and directions given at different pages.
Deployment of Qualified Engineers at Work Sites by the Contractor - The Contractor shall employ 1 No. of qualified Graduate Engineer for works Rs. 200 Lakh or more and 1 No. of Diploma Engineer for works costing more than Rs. 25 Lakh, but less than Rs 200 Lakh
MAQ - Provision of 3 phase 750 V AC supply in pit lines / washing lines at Mangalore Central Railway Stations for LHB Coach Maintenance - Electrical Arrangements.
J-E-14-2026-27-W
J-E-14-2026-27-W
Open
Works - General
9 Months
Palakkad, Kerala
₹0
₹6.1 L
23 Jul 2026
29 Jun 2026
9 Jul 2026
89 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 3,03,87,417 | ||
| — | 340.00 | — | — | ||
| Drilling of cable duct under Railway Track/Railway land by Horizontal drilling method as directed by site engineer incharge. | — | — | — | 13,87,200 | |
| — | 400.00 | — | — | ||
| "Laying of 3 core 300sq.mm 11kV HT cable or releasing and coiling of 3 core 300 sq.mm11kV HT cable into cable drums or re-laying of 3 core300sq.mm 11kV HT cable as directed by site engineer incharge. Note: - Cable will be supplied by Railway from the Office of SSE/Electrical In- Charge of the work." | — | — | — | 96,000 | |
| — | 2.00 | — | — | ||
| Supply, fixing and commissioning of outdoor heat shrinkable type end termination kit for 11kV, 3 Core, 300sq.mm XLPE UG cable | — | — | — | 27,850 | |
| — | 16.00 | — | — | ||
| Supply, fixing and commissioning of indoor heat shrinkable type end termination kit for 11kV,3 core, 300sq.mm XLPEUG cable | — | — | — | 1,73,280 | |
| — | 1.00 | — | — | ||
| "Supply, erection, testing and commissioning of floor mounted 11kV, 630A HT panel with 1 Nos of VCB as incomer and Two nos. of VCB as outgoing as per enclosed detailed specification and relevant standards. Note :- Provision for adding one more Incomer & outgoing VCB Panels in Future will be provided with suitable capacity of bus bars by the Contractor." | — | — | — | 17,92,656 | |
| — | 413.00 | — | — | ||
| Excavation of cable trench in all kinds of soil up to a depth of 1.0 Mtr. & Width of 0.3 Mtr duly clearing the roots of trees etc. and refilling with the excavated soil up to normal level. Depth and Width can be varied based on site Condition as directed by site engineers in charge. Concerned Measurement will be taken in Cubic meters. | — | — | — | 2,56,060 | |
| — | 800.00 | — | — | ||
| "Transportation and burying of HDPE pipe 160mm dia pressure rating up to 4PN (Material Grade-PE 80) Under Railway track/Road Crossing/ in the excavated cable trench with suitable fixing hardware. Note: HDPE pipe will be supplied by Railway from the Office of SSE/Electrical/Works/PGT." | — | — | — | 41,600 | |
| — | 2.00 | — | — | ||
| "Supply erection testing and commissioning of 1600 KVA 11kV/750 V Package/ compact outdoor substation with one incomer RMU panel consisting of two numbers of 630A Load break switch and one number of SF-6/Vacuum circuit breaker with 630ABus bar, transformer unit and LT panel consisting of 1 number of 750V/800V/1000V,2000A 65kA Drawout ACB with 50 cm long 2000A copper Busbar for each phase and neutral as per specification (MAKE ;- ABB, SEIMENS, L&T, KIRLOSKER ELECTRIC or SCHENIDER make only)." | — | — | — | 1,31,72,000 | |
| — | 1.00 | — | — | ||
| "Supply erection testing and commissioning of Medium Tension MDB having overall minimum size of size of 6.2m W x 1.85m H x 1m D fabricated with 10 SWG CRCA sheet with 2 Nos of 800V, 65kA 2000A four pole draw out type ACB as incomer and five numbers of fixed type 800V 800A FP ACB as outgoing with 2000A main copper busbar size having minimum length of 3.6m long as per specification Note:- 1) In the above panel, in addition to the Five numbers of out going, only space for accommodating 1 No. of ACB has to be provided by the contractor. 2) Suitable capacity & length of bus bas to be provided in the said open space for accommoding future/upcoming 1 Nos of ACB. 3) Inter locking to be provided between incoming ACBs" | — | — | — | 35,34,000 | |
| — | 16.00 | — | — | ||
| Supply and fixing of Indoor type cable end termination for 3.3KVgrade Three core 400Sqmm aluminium cable | — | — | — | 1,70,880 | |
| — | 8350.00 | — | — | ||
| "Transportation & Laying / clamping / threading of 1Core/4 Core XLPE cable (Size above300 Sq.mm upto and including 400Sq.mm) through trench, Cable protection pipe, Wall/shelters, FOB, etc as directed at site, with suitable clamps and termination duly supplying required Aluminium sockets, etc., Note: - Cable will be supplied by Railway from the Office of SSE/Electrical/W/PGT." | — | — | — | 7,93,250 | |
| — | 8000.00 | — | — | ||
| "Transportation and laying /fixing of HDPE pipe 90mm dia pressure rating up to 4PN (Material Grade-PE 63) in the excavated cable trench/building wall/FOB etc.., With suitable GI fixing hardware like T-Joints, L-Joints, shall be used at appropriate locations. So that cable can be easily inserted and removed wherever need arises. Note: HDPE pipe will be supplied by Railway from the Office of SSE/Electrical/Works/PGT." | — | — | — | 3,76,000 | |
| — | 32.00 | — | — | ||
| "Supply and fixing of Indoor type cable end termination for 3.3KVgrade single core 400Sq.mm aluminium cable. Note :- 2mm thick Round wire (Aluminium) armouring shall be provided for the siad cable." | — | — | — | 1,13,920 | |
| — | 4.00 | — | — | ||
| Supply and erection of Outdoor type kiosk made up of 10SWG CRCA sheet with 0.5m long 100x10mm copper bus bar 4 numbers and 1No. 800V,630A 50kA 4 pole MCCB as incomer, 1No. 800V,630A 4 pole power contactor, 1No.Measuring & Monitoring Relay (MMR), 1No.ON/OFF push button switch, two auxiliary circuits each auxiliary circuit having 1No.750/415V 200VA control transformer and 1No.Auxiliary contactor(1NO+1NC), 2 sets of HT fuse units & 2 sets of LT fuse units as per specification | — | — | — | 13,50,732 | |
| — | 50.00 | — | — | ||
| Supply of 750V feeder extension cables set consist of (i)1 No. 1.8/3KV grade 3X150sqmm cable, 1No. 1.8/3KV grade 1X95sqmm cable and 1No. 750V grade 2X2.5 sqmm cable all as per Harness Nos. 1 & 1B only to EDTS-252 Rev-1-clause. 2.1(B) and 1No. 1.8/3KV grade 1X70sqmm copper cable cross linked polyolefin insulated including laying of all the above cables in pipe | — | — | — | 6,75,000 | |
| — | 4.00 | — | — | ||
| Supply & fixing of 1 No.IVC female socket assembly for ZS couplingof LHB coaches (500Acapacity) with enclosure made of 10 SWG MS sheet and fixing the same in the cut rail/ TCC column with suitable brackets as per standard specification. | — | — | — | 2,84,800 | |
| — | 4.00 | — | — | ||
| Supply of 2 Nos. of IVC jumper plug assembly for ZS coupling as per RCF specification No. EDTS-105 Rev-E including supply of set of feeder cables 10M long consist of (i)1 No. 1.8/3kV grade 3X150 sq.mm cable, 1No.1.8/3kV grade1X95sqmm cable and1No. 750V grade 2X2.5sqmm cable all as per Harness Nos. 1 & 1B only to EDTS-252 Rev-1-clause. 2.1(B) and 1No.1.8/3kV grade1X70sqmm copper cable cross linked polyolefin insulated including supply of flexible polyimide conduit of size 80mm and laying of all the above cables in pipe | — | — | — | 13,35,116 | |
| — | 1000.00 | — | — | ||
| Supply, laying and provision of 6 SWG GI wire as earth continuity including termination | — | — | — | 34,000 | |
| — | 8.00 | — | — | ||
| "HT Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Note :- 1) The work has to be done as per the drawing enclosed. 2) Drawing Approval may be obtained before Commerncent of work. " | — | — | — | 92,584 | |
| — | 8.00 | — | — | ||
| "Supply of Concealed type Earthing. This consisting of supply at site, erection, testing and commissioning of G.I. Earth Electrode 50mm dia, 3000mm long, 'C' class (heavy duty/ISI marked supply and and fixing of earth inspection chamber, lid, as per CEE Drg. No.EL/P/TYPE-1022 with charcol & salt / Bentonite Compound Filling, which includes the cutting and removing of granite / marble / kadappa stone paved platform and cement concreted areas etc., excavation / augering of earth pit by suitable boring equipments. The earth pot shall be provided in level with flooring. The above includes reconstruction of the area of granite / marble / kadappa stone / cement concrete etc.., to bring back to the original condition duly providing granite / marble / kadappa stone / cement concrete etc.., The earth pot shall be painted black and earth value to be recorded" | — | — | — | 57,280 | |
| — | 2.00 | — | — | ||
| Fabrication supply and placing of Input Output trolley with 3 Nos. IVC female socket assembly for extending supply to LHB coaches (500A capacity) with enclosure made of 10 SWG CRCA sheet powder coated | — | — | — | 7,60,000 | |
| — | 3.00 | — | — | ||
| Fabrication supply and placing of trolley for double end plug assembly with 10m control cable as per Drawing no. E/CN/ERS/SK/23-24/14 | — | — | — | 3,00,000 | |
| — | 40.00 | — | — | ||
| Fabrication supply and fixing of 50 x 6 mm size Copper flats for transformer earthing | — | — | — | 1,30,000 | |
| — | 40.00 | — | — | ||
| Supply and laying of electrolytic tinned copper flat of 40mmx6mm (11/2"x1/4") size as per standard | — | — | — | 94,880 | |
| — | 1300.00 | — | — | ||
| Supplying of reinforcement for RCC work including straightning , Cutting, Bending, placing inposition and binding all complete. | — | — | — | 1,50,800 | |
| — | 50.00 | — | — | ||
| Supply and provision of Mass concrete with 1:2:4 ratio | — | — | — | 5,47,350 | |
| — | 35.00 | — | — | ||
| Supply and provision of Mass concrete with 1:3:6 ratio | — | — | — | 3,22,245 | |
| — | 40.00 | — | — | ||
| Supply and spreading of blue metal (Ballast) of 40mm size | — | — | — | 55,640 | |
| — | 85.00 | — | — | ||
| "Supply and fabrication of fencing panel of 2.4mtr Height and 1m Width made with 8SWG (Nominal Size ) GI Chain Link Mesh 50X50mm inner size of the diamond design, 40X40X5/6mm MS angle Outer frame in 2mtr wide and Vertical T section support with 40X40X5/6mm MS angle iron and 40X5/6mm MS flat at middle , Horizontal brazing at Centre with 40X5/6mm MS flat etc.., In welded Construction, Install the Fencing panels on the channel poles already erected by welding,Suitable door and locking Arrangements , painted with approved enamelShade/AL paint after Applying epoxy Primer etc., as Required. Note:- Fencing to be done as per the drawing enclosed." | — | — | — | 3,94,485 | |
| — | 50.00 | — | — | ||
| fabrication, Supply and Erection of approximate 2.9m long channel pole of size 100X50mm with MS base plate of size 200X200X5mm, painted with approved enemal Shade/AL pain after epoxy primer for welded mesh fencing of the substation including concreting. | — | — | — | 2,32,050 | |
| — | 10.00 | — | — | ||
| "Supply at site & placing of flat type cable route indicator at regular intervals on straight route and one each at every route diversion from straight line as directed by site engineer. The said cable Route Indicator has to be grouted in a concrete mix of ratio 1:3:6with 300mmX200mmX300mm size." | — | — | — | 8,160 | |
| — | 8.00 | — | — | ||
| Supply and fixing of Danger Board suitable for 11 KV /22 KV/33 KV systems, as per IS.No: 2551, along with one number of clamp made out of 25mm X 4 mm size including bolts & nuts for fixing on structures and painting | — | — | — | 2,472 | |
| — | 50.00 | — | — | ||
| Supply, fabrication and laying of 50mmx6mm GI flat for earthing purpose as per relevant standard and as instructed by the Engineer-in-charge | — | — | — | 23,200 | |
| — | 6.00 | — | — | ||
| Supply and spreading of chequered electrical rubber mat of 2 m long and 1.0 m wide and 12 mm thick to withstand 40 kV(rms) as per IS No: 5424 | — | — | — | 12,378 | |
| — | 5.00 | — | — | ||
| Supply and fixing of Protected area Board of Size 750X300X1.6mm as per Drawing No.EERE/TSS/16-Enamel type | — | — | — | 3,350 | |
| — | 1.00 | — | — | ||
| Provision of printing the substation Electrical Drawing in the viniyal (Approx. Size 6 X 4 feet) and same has to be fixed in the suitable location as directed at site Engineer. | — | — | — | 3,094 | |
| — | 35.00 | — | — | ||
| Hiring of JCB | — | — | — | 57,295 | |
| — | 100.00 | — | — | ||
| Form work for Centring shuttering including strutting proping etc. and removal of form for Walls includingattached plastres etc. etc | — | — | — | 47,200 | |
| — | 2000.00 | — | — | ||
| Steel work in build up tubular trusses including cutting hoisting, fixing, fixing in position and appling priming coat approved steel primer, and two coatsof enamel paint, welded and bolted including special shaped washers etc. Complete Hot finished welded type tubes | — | — | — | 4,86,000 | |
| — | 212.00 | — | — | ||
| Supply and installation of pre-coated galvanised iron profile sheets as per specification | — | — | — | 2,35,320 | |
| — | 4200.00 | — | — | ||
| Fabrication and Supply of GI flat /Angles Hot dip galvanised as per RDSO standard manufactured by RDSO approved manufacturers for fixing in catwalk pillars or as directed by SSE-In- Charge including fixing. | — | — | — | 6,72,000 | |
| — | 12.00 | — | — | ||
| "Supply & Fixing of 40W LED street light fittings on the Octogonal Poles/Rail Poles/Wall of the building with suitable GI pipe and clamps if necessary. GI pipe has to be bend as directed at site including wiring arrangements/Point wiring to the fittings. Preferable Makes :- Wipro, Bajaj, Havells, Surya, Syska, Osram, Philips, CG or any other Reputed makes." | — | — | — | 60,000 | |
| — | 154.00 | — | — | ||
| "Supply and laying of ISI marked Medium duty PVC rigid wiring conduit pipe of size 20mm dia for Open wiring including, tees, bends, junction boxes etc and finishing to original level & Wall thickness 1.4mm +/- 0.2mm. Preferable Makes :- Precision, Anchor, Avoplast, VIP, Balco, Inplast or any other reputed makes. " | — | — | — | 9,240 | |
| — | 107.00 | — | — | ||
| "Supply and Single phase wiring by means of 2 nos. of 1.5 Sq.mm (P&N) and 1 No. of 2.5 Sqmm (Earth) size Flame Retardant Low Smoke & Halogen (FR- LSH) PVC insulated single core multistranded flexible copper cable with ISI mark of approved make with coded color for Phase, Neutral and Earth through already erected PVC casing and capping or pipes, junction boxes, distribution boards etc., Preferable Makes of FR-LSH Cables :- Poly Cab, Havells,V-Guard, Bonton or any other reputed makes, " | — | — | — | 16,050 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocument-MAQ-750V.pdf
ATTACHMENT
GCC April 2022
ATTACHMENT
GeneralConditionsofContractGCC-April-2022.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .